Search Documents

By Volkan Arslan

This study aimed to remove the contaminants in quartz sand by using an eco-friendly method and to obtain high-purity quartz. For this purpose, ultrasound-assisted acid leaching was applied. Equal amounts of a mixture of diluted hydrochloric and oxalic acids were used as the solvent. Response surface methodology (RSM) was used for optimizing, modeling, and predicting the experimental parameters. The correlation coefficient ( R2) of the proposed quadratic model for the relationship between iron removal yield and test parameters was calculated as 0.9731 and it was determined that the predicted and actual values were compatible. Finally, optimization experiments were made and optimum experiment conditions were revised and determined as 83.38 °C of leaching temperature, 196.35 min of leaching time, 2.86 M of acid concentration, and 202.24 W of ultrasound power. Under the optimum conditions determined after optimization, the highest yield of iron removal was determined as 95.08%. Under the optimal parameters, the SiO2 content of the concentrates increased from 97.841 to 99.907% and the Fe2O3 content reduced from 0.225 to 0.011%.

Jul 12, 2021

By J. C. Irvine

Meramec Mining Company, a joint venture by Bethlehem Steel Corporation and St. Joe Minerals Corporation, is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge Mine located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during an exploration program to discover new lead orebodies. An airborne magnetometer survey which was run by the U. S. Geological Survey, the Missouri Geological Survey, and several min¬ing companies was published in 1950 and showed an anomaly in the Pea Ridge area. Test holes drilled in 1953 and 1954 revealed the presence of a large orebody of probable commercial significance; additional drilling in 1956 and 1957 provided confirmation of this. Meramec Mining Company was incorporated in 1957 and shaft sinking began in the latter part of that year. The Pea Ridge orebody lies under about 1300 feet of sediments. It is tabular, about 2600 feet long and up to 600 feet thick, and lies in an approximate east-west delineation. The orebody dips about 800S and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite, The Pre-cambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 feet 1 inch in diameter and 2500 feet deep. No. 1 shaft, equipped with an "A" type head-

Jan 1, 1972

By Keith Olson

In the heart of Appalachia, where coal mining has shaped communities and economies for generations, Bluefield State University (BSU) has made a landmark decision to reestablish its mining engineering technology program. This move comes at a critical juncture for both the university and the mining industry, which faces significant workforce challenges amid evolving technological demands and an aging professional demographic. The program’s revival represents an educational initiative and a strategic response to industry needs and regional economic development. Nestled in the mountains of southern West Virginia, BSU has a storied history intertwined with the region’s mining heritage. The institution’s decision to bring back this specialized program after a hiatus of several years signals a renewed commitment to serving both regional industry demands and providing career pathways for students in an area where the cyclical nature of resource extraction economies has often limited economic opportunities. “This program’s return reflects our deep understanding of this region’s needs and our commitment to preparing graduates for meaningful careers that support our local industries,” said Darrin Martin, president of Bluefield State University. “We’re bridging the gap between education and industry with a modernized curriculum that addresses today’s mining challenges while preparing for tomorrow’s innovations.”

Jun 1, 2025

By X. Baolin, R. Guru, M. Peiravi, M. K. Mohanty, Z. Qian, R. Ma, Z. Yude, L. A. Ackah

"Acid mine drainage (AMD) is produced when exposed pyrite (FeS2) reacts with air and water to form an acidic solution that usually contain contaminant levels of heavy metal ions. AMD can potentially contaminate surface water and soil if not treated. The primary objective of this study was to investigate the removal of dissolved aluminum, iron and zinc metal ions from natural AMD using water treatment residue (WTR), a low-cost adsorbent. WTR sorbent generated as waste material in drinking water treatment plants (WTP) was characterized and utilized for the sorption of Al, Fe and Zn in AMD collected from an abandoned coal mine site in southern Illinois that generates approximately 20 gallons per minute of AMD. Sorption experiments were performed using batch technique to obtain rate and equilibrium data. The effects of various parameters on sorption capacities of WTR were observed by varying contact time, pH of the AMD and WTR dosage. The adsorption studies showed rapid uptake in general for the first 80 minutes for Fe and Zn but much earlier for Zn. Further increase in contact time did not show significant change in equilibrium concentration indicating the onset of adsorption equilibrium. After the batch treatment of the AMD water with the WTR, the removal of Al, Fe and Zn were 99.8%, 99.85% and 95.5% respectively. The pH of AMD increased from 2.64 to a near neutral point of 6.74 after treatment. The laboratory results show that the low-cost WTR, which is an abundantly available industrial waste, has proven potential to significantly reduce the high metal ions in acid mine drainage. INTRODUCTION Mining activities provide the basic raw materials needed for infrastructure development and economic growth world-wide. However, it is well recognized that mining activities have been the cause of a variety of environmental pollutions, including AMD. Water seeping out of an old abandoned mine is generally characterized by low-pH with heavy loads of dissolved sulfates (SO4) and metal species such as Fe, Al and Zn among other dissolved elements categorized as toxic metals. The Bureau of Land Management’s Abandoned Mine Lands (AML) program reported the existence of about 46,000 abandoned mines in the United States. Several environmental problems have been reported to be associated with these mined out sites such as heavy metal poisoning, loss of vegetation, air pollution etc. (Boulanger & Gorman, 2004)."

Jan 1, 2017

By Zhan-fang Cao, Hong Zhong, Li-feng Li, Shuai Wang, Xiao-yu Cao, Guang-yi Liu, Ming-ming Wang

"In recent years, there has been an increasing focus on the hydrometallurgical processing of molybdenite, with the decline of high-grade and easily handled molybdenum minerals. In this work, a novel method of selective extraction of complex molybdenite concentrate, which is characteristic of high-grade copper ore, has been investigated. The results show that the leaching of chalcopyrite was impacted by the pH of the electrolyte when sodium carbonate and ammonium acid carbonate were added to the electrolyte. The leaching rate of molybdenum reached 99.39%, but chalcopyrite could not be leached at all in 240 min under experimental conditions of liquid-to-solid ratio 25:1, concentration of NaCl 4 mol/L, pH=9, room temperature and agitation speed 400 rpm. The grade of copper in the residue was 21.84%, with a recovery 99.93%. The technology of selective electro-oxidation leaching of molybdenum and recovery of copper from complex molybdenite concentrate is an effective separation method. The diffusion control model can be used to describe the process of leaching of molybdenum. The activation energy of the leaching reaction was found to be approximately 9.21 kJ/mol.IntroductionWorldwide, high-grade and easy-to-handle ore is decreasing, while the proportion of low-grade and complex ore is increasing. Porphyry copper ores with associated low-grade molybdenite are very abundant in China. Molybdenum is a valuable byproduct in the processing of porphyry copper deposits where the molybdenum is present in low quantities in the form of molybdenite (MoS2). In the conventional processing of copper sulfide ores by froth flotation, most of the molybdenite in the ore floats along with the copper sulfides. In this way, a bulk copper-molybdenum concentrate is produced. Afterward, the bulk coppermolybdenum concentrate is treated by differential flotation to obtain a rougher molybdenum concentrate, which requires several successive cleaning steps to produce a final molybdenum concentrate. However, it is widely recognized that flotation alone cannot economically produce a high-grade molybdenite concentrate, i.e., with less than 0.5% Cu. Therefore, in most cases, it is necessary to use a final step of chemical purification of the molybdenite concentrate to reduce the copper content to a level suitable for the market (Antonijevic and Pacovic,1992; Gerhardt et al., 2001; Fu and Zhong, 2003; Reza et al., 2006, Rafael et al., 2013)."

Jan 1, 2015

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom-designed radial sector sampler , six large blasthole samples were collected to perform the test developed by Pierre Gy to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to total fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32 percent and ±49 percent for copper and molybdenum, respectively. A classical statistical analysis conducted on the data confirmed the level of RSD native to the mine. About 95 percent of the sampling error was produced from one step in the sampling protocol, that of reducing the 1-kg (2.2-lb) sample to a 50-g (0.1-lb) sample for chemical analysis. To minimize the FSE, the use of a slightly different protocol is recommended. The 1-kg sample (2.2-lb) should first be crushed to a 0.2 cm (0.08 in.) particle size. A 250-g (0.5-lb) split should then be taken and finely ground, from which a 50-g (0.1-lb) split should then be taken. These simple steps will reduce the FSE to ±7.9 percent and ±17 percent for copper and molybdenum, respectively. The modified sampling protocol effectively reduces to zero the probability of misclassification of low-grade ore. IntroductionThe Erdenet copper-molybdenumopenpit mine is located in Erdenet in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is 1.5 to 3 km (0.9 to 1.8 miles) wide and about 25 km (16 miles) long (Erdenet Mining Corp., 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 Mt/a (29 million stpy) of ore."

Jan 11, 2017

By R. R. Swanson

Liquid ion exchange is becoming more and more important in hydro-metallurgical processing and recovery of metals. The key to success for this process are reagents which have suitable operating characteristics. One of these important characteristics is a relatively fast phase separation rate in the extraction and stripping circuits, as this greatly affects the size of plant required. A test for measuring phase separation rate is needed to help evaluate liquid ion exchange reagents. Such "a test also would be useful for evaluating carrier solvents that are used for diluting the re-agents. In fact, one standard test method would be very desirable as it would provide a common basis for comparing reagents and sol-vents. The phase separation test described in this paper has been used successfully for several years with the copper reagent, LIX®64N. The test is set up for feed liquors containing low copper concentrations. For other types of systems, modifications in procedure probably would be necessary. However, this test and the associated apparatus could be the basis for a standard phase separation test.

Jan 1, 1972

By John W. Sweeney

Florida is usually thought of as a vacation State, not a mining State, yet Florida has been the leading producer of phosphate rock in the United States for 85 consecutive years and in 1978 supplied over 80 percent of the national output and over 30 percent of the world's output. It is estimated that the Central and South Florida phosphates contain 412,800 short tons (374,000 metric tons) of U308, that 115,000 short tons (104,000 metric tons) of U308 will be contained in the wet-process phosphoric" acid procsssed in the United States through the year 2000, and that 54,000 short tons (49,000 metric tons) of U308 will be available from Florida. In 1978, two companies in Florida and one in Louisiana went on-stream recovering uranium oxide from wet-process phosphoric acid and three others started construction of U308 extraction facilities. These six companies will have the capacity to recover 2,137 short tons (1,900 metric tons) of U308 annually in 1980, which will account for about 15 percent of our domestic requirements.

Jan 1, 1979

By Zhiyuan Ma, ZUI WANG, Xincheng Hu, Jianwei Cheng, Junhong Si, Yi Qin, Gao Ke

The harmfulness and destructiveness of mine gas explosion is quite serious, which is the first of all kinds of coal mine disasters. Once the gas explosion occurs, it could instantly generate explosion shock waves, high temperature airflows, and disaster gases, which cause the destruction of underground ventilation structures, disruption of airflow direction in a mine ventilation network, and miners’ deaths by asphyxiation. As an important barrier to prevent the spread of accidents caused by the gas explosion, the safety and reliability of the mine seal affects the mine’s production and the health of workers. Due to the demands of coal mine production and transportation, a large number of longitudinal and horizontal roadway networks have been developed underground. There are not only many flat and straight roadways in the complex roadway network structure, but also a large number of different types of bifurcations and bends. Once a gas explosion occurs, the impact of the blast waves on the mine seal after passing through the complex path is difficult to determine. Therefore, this paper establishes a numerical model of bifurcated and cornered roadways and studies how the impact of gas explosion shock waves on the structure of sandwich mine seal after passing through different types of bifurcated and cornered roadways. The damage state of sandwich mine seal is analyzed. The researching finding could prevent and manage the spread of gas explosion disaster, and improve the disaster mitigation of mine explosion accident.

Jul 11, 2023

By David Mast, Irwan Halim, Brian Hagan, Kaveh Talebi, Jason Edberg, Amanda Foote

On June 14, 2023 Jay Dee Contractors’ Tunnel Boring Machine (TBM) “Phoenix” holed through and completed mining the second drive of the I-75 Segment 3 Storage and Drainage Tunnel. Completion of the tunnel came only after overcoming several challenges, including a groundwater intrusion event which deposited thousands of cubic yards of wet ground material into the tunnel. This paper will discuss the events which delayed completion of the tunnel by over nine months, the risk management and construction approaches assumed by the Design-Build team during bid, several challenges faced by Design-Build teams when building stormwater resilience tunnels using traditional Department of Transportation standards, and recommendations for improving risk allocation and proposal documents for future similar Design-Build tunnel projects.

Jun 23, 2024

By G. Deschênes

In an earlier study (Deschênes et al., 2009), gold and silver were shown to be efficiently extracted from samples taken from the Kupol Mine in Russia using lead nitrate in a cyanide leach system. In the current study, a com-parison of the technical and economic merits of a new technology called CANMET enhanced leaching process (CELP) was made with the cyanidation/acidification-volatilization-recycling (AVR) process using eight metal-lurgical variability samples, as well as a large composite sample, which was to represent the initial two years of Kupol mill feed. The composite sample leach feed assayed 33.4 g/t Au and 289 g/t Ag. The metallurgical results from the large composite sample demonstrated that CELP produced very similar gold and slightly higher silver leach extractions compared to the conventional cyanidation/AVR leach conditions at 1/2 the cyanide concentra-tion (1,000 ppm NaCN in CELP vs. 2,000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton was approximately the same for the two technologies (total cost of CELP with the use of Merrill-Crowe at $46.48/t, with cyanidation/AVR at $46.13/t). However, the implementation of CELP would eliminate a capital expenditure of approximately $5 million for an AVR system based on a 2005 feasibility level cost estimate. Eight variability samples used to confirm the composite sample results showed that, on average, the gold leach extractions with CELP and the conventional leach conditions were very similar, but the average silver leach extraction was 2.1% higher for CELP. Furthermore, CELP silver leach extraction was 4.6% higher on average compared to conventional cyanidation for the four mid-grade variability samples evaluated. The decision was made to remove AVR cyanide recovery from the flowsheet and implement CELP at Kupol. The ability to use the conventional leach equipment with CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2010

By R. R. Bhappu

The metallurgical processing industry is in the midst of a hydrometallurgical revolution with mining companies looking for low cost, energy efficient and environmentally friendly technologies for processing sulfide ores and concentrates. The Intec Copper Process is one of the most advanced of these technologies and has the potential to greatly change the way copper concentrates are treated in the future. Specifically, the Intec process has the ability to be built on a small scale and at mine sites while being much more economic than conventional smelting. Intec Copper has constructed a I tonne of copper per day demonstration plant in Sydney, Australia designed to verify metallurgical and operational performance. This paper will describe the process in more detail and provide preliminary results of the process based on the plant's performance. It will also compare the Intec Copper Process with a few of the competing technologies and evaluate the relative economic merits of Intec.

Jan 1, 1999

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By R. R. Hall

Tests were conducted to assess the potential of column flotation for beneficiation of a talc ore from Montana. This ere contained approximately 80% talc, with the gangue comprised mainly of chlorite, silica, and dolomite. A tributylamine, MIBC, and sodium silicate reagent suite proved effective for talc flotation. Rougher-cleaner column flotation in a continuous open-circuit produced a final talc concentrate which contained 0.90% Al2O3. 0.17% CaO, and 1.28% Fe2O3. These analyses represented impurity rejections of 77, 85, and 65%, respectively. Weight recovery for this open-circuit was 52%; however, weight recovery was estimated to be 75% with cleaner tailings recycle. Results from this investigation show that column flotation is a viable means for beneficiating talc.

Jan 1, 1990

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corporation operates a modern coal preparation plant in Van, West Virginia. Since the start-up of the Van Plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miner's vacation the original system, which included two screw conveyors and a drag conveyor, was replaced by an installation utilizing two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance. The Van facility is a heavy media plant designed to handle 127 mm x 0 raw metallurgical quality coal from the Powellton seam at a maximum feed rate of 590 TPH (metric tons per hour). Depending on mining conditions, the clean coal recovery rate averages between 50 and 65%. The plant is set up with three types of cleaning circuits. Coarse material (127 mm x 12 mm) is cleaned in heavy media baths. Intermediate size material (12 mm x .5 mm) is cleaned in heavy media cyclones. Fine coal (.5 mm x 0) is cleaned in a hydrocyclone1 froth flotation circuit.

Jan 1, 1981

By P. M. Pettit

Hydrologic investigations at Gold Quarry began in 1989 and continued through 1991. Hydro-stratigraphic units include Tertiary sedimentary rocks, Paleozoic siltstones and carbonates. These units display complex and variable aquifer parameters as a function of faulting and hydrothermal alteration, creating compartmentalized hydrologic domains. Testing has included step-tests, spinner production logs and constant discharge tests. Two Three-Dimensional Finite Element Models have been developed, one for optimizing the pit dewatering system and the second for predicting regional impacts of dewatering. Aquifer testing and long term pumping have been used to calibrate both Finite Element Models.

Jan 1, 1992

By Jieliang Wang, Shiwen Yi, Zhao Cao, Peng Zu

Bayan Obo ore contains mainly bastnaesite, monazite and associated iron, fluorite, calcite, dolomite, barite, and trace amount of columbite. Due to its complex mineral compositions and similar mineral properties, it is difficult to separate and obtain rare earth and fluorite concentrates with high purity by conventional magnetic separation and flotation. In this paper, a stepwise magnetic separation process comprised of wet permanent magnetic separation (PMS), wet electromagnetic separation (EMS), and superconducting magnetic separation (SCMS) was proposed to pre-concentrate iron, rare earth, and fluorite minerals from Bayan Obo ore. The results showed that iron, rare earth, and fluorite preconcentrates with high purity and low impurity content could be achieved, which might be helpful to shorten the technological process and improve the separation efficiency for the subsequent flotation of iron, rare earth, and fluorite minerals.

Sep 15, 2020

By J. M. D. Wilson

The literature relating to binders in iron ore pelletizing is reviewed from the point of view of their established or proposed bonding mechanisms in green and dry pellets.

Jan 1, 1981