Search Documents

By T. L. Barone, J. R. Patts, L. D. Patts, S. J. Janisko

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. IntroductionAirborne coal dust is a byproduct of coal production, and engineering controls exist to deal with both the respirable dust health hazard as well as the float dust explosion safety hazard. Float coal dust, smaller than 75 µm (0.003 in.) in size, can deposit throughout mine entries and propagate explosions that had been initially fueled by methane gas. The inertization of float coal dust with rock dust helps prevent a potential secondary float coal dust explosion, but a preferable course of action is to significantly reduce the hazard by removing float coal dust from the airstream before it has the opportunity to deposit on the mine’s surfaces.Since 1970, disasters due to explosions in underground coal mines have caused 201 deaths in the U.S. mining industry, including 29 deaths in a single mine explosion in 2010 (Wade, 2010; U.S. Mine Safety and Health Administration, 2015). The U.S. National Institute for Occupational Safety and Health (NIOSH) had initiated a fiveyear research project that aims to investigate methods and technologies to reduce the potential for secondary coal dust explosions by the purposeful capture and/or suppression of float coal dust prior to its deposition on the mine roof, rib and floor (NIOSH, 2013). The project aims to evaluate the efficiency of methods to reduce longwall and belt airway float dust in the general airstream as well as methods to capture it at or near the source. Prioritization is given to longwall sections given the amount of coal produced relative to continuous miner sections, but the research is open to technologies that may be adapted from one method of mining to another."

Dec 1, 2016

By Jey K. Jeyapalan

A characteristic common to most tailings dam failures caused by earthquakes or excessive rain storm is that the tailings tend to liquefy and flow for substantial distances as a viscous fluid, with the potential for extensive damage to property and life. Failures of El Cobre, Chile (1965), Mochikoshi, Japan (1978), Aberfan, Wales (19661, Buffalo Creek, West Virginia (1972) are examples of such catastrophic incidents. In these four incidents more than 400 lives were lost, and the loss of property was approximately $200 million. In order to be able to assess the potential for damage in case of such a failure, it is necessary to predict the possible extent of flow slide movement. This paper discusses simple procedures for performing such analyses. Also, in order to illustrate the use of these analysis procedures in tailings dam design, two case histories are analyzed.

Jan 1, 1982

By William Gleason

"More than 6,300 people converged on the Colorado Convention Center for the 2017 SME Annual Conference and Expo and 119th National Western Mining Conference in Denver, CO on Feb. 19-22. Many of them crammed in to hear Douglas Silver deliver the keynote address to the conference.Silver is a portfolio manager for Orion Mine Finance, a private-equity fund focused on providing funding to advanced-stage base and precious metal projects and is one of the most respected voices in the field of mineral economics. Prior to joining Orion, he served as chief executive officer and chairman of International Royalty Corp., a global mineral royalty company, which he founded in 2003 and sold in 2011.Those who were hoping that Silver would deliver at least a bit of optimism during his 90-minute presentation got what they came for from the talk titled, “When are commodity prices going to rebound?”It marked the second time Silver has presented the keynote address to SME, the first was in 2008 and was delivered during the height of mining’s super cycle (ME, June 2008). In his 2017 address, Silver looked back on the previous 10 years and the massive contraction of the global economy that resulted from the great recession that began near the end of 2008.It has been a challenging time for the mining industry. About US$1.4 trillion was lost in the global mining stocks from 2011 to Jan. 6, 2016. Major mining companies exceeded $60 billion in write downs between 2012 and 2013 and investors lost confidence in the sector, putting the global mining industry into a bear market that has taken mining equities to historic lows.However, that was then and this is now.Using numerous examples, including rising commodity prices, a steady decline in the U.S. unemployment rate, increases in discretionary income and the Dow Jones Industrial Average, which topped the 20,000 mark for the first time ever in February, Silver theorized the current down cycle is near its end and the demand for metals and other commodities will see a sharp increase by 2025. He also noted that investors are beginning to rotate back into mining equities."

Apr 1, 2017

By Jr. Watts

The American Mining Congress and the U.S. Bureau of Mines have formed a collaborative research team to develop, implement, and evaluate a comprehensive control strategy to reduce diesel particulate matter concentrations without degrading other air quality parameters at an underground noncoal mine. Other participating organizations include Caterpillar, Inc., the Mine Safety and Health Administration, and the University of Minnesota. After extensive baseline information and air quality data are collected, available control strategies to reduce diesel particulate matter exposures will be implemented, individually or in combination, and evaluated. This paper discusses the objectives and protocol of the collaborative effort to evaluate diesel particulate control technology.

Jan 1, 1995

By S. M. Hsiung

Chain pillar design formula under weak roof condition was developed by statistically analyzing the results from the three dimensional finite element parametric analyses. The parameters such as mechanical properties of the roof and floor strata, overburden depth, panel width and length, and coal strength were incorporated in the formula. A conversion formula which transfers a rectangular chain pillar into a square chain pillar of equal strength is proposed. The influence of high in-situ horizontal stresses, which are often encountered in the coalfield, on chain pillar stability is also discussed.

Jan 1, 1984

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By SANJIT KUMAR PAL, Sarvesh Kumar, Arindam Guha

The integrated geophysical study around pipe 1 and pipe 2 in Wjarakarur Kimberlite Field (WKF) assisted in comprehending the response of pipes. In the present study, we have attempted a combined analysis of very low-frequency electromagnetic (VLF-EM), electrical resistivity tomography (ERT), and magnetic methods to analyze the response from pipe 1 and pipe 2. A comparative analysis along all the profiles revealed the extension, depth, and geometry of the pipes. The results of VLF data and ERT data have been compared for two profiles of pipe 1 and pipe 2. Fraser-filtered grid map generated from all profiles of pipe 1 proficiently demarcated the trend of kimberlite pipe extension with high Fraser filter value associated with kimberlite. The ground-based magnetic data around pipe 1, pipe 2, and pipe 6 have been processed to analyze the magnetic behavior and subsurface structure based on the susceptibility contrasts. Analytical signal (AS) map revealed the extension of pipes, which was validated with the Fraser-filtered grid map. Analytical signal anomaly pattern reveals that pipe 1, pipe 2, and pipe 6 are trending in SW-NE, NE-SW, and NE-SW, respectively. Based on this study, the results indicate the conducting nature of pipe 1, whereas pipe 2 is resistive in nature. Further, the Euler deconvolution technique has been applied to calculate the possible depth of pipes from magnetic data. The comparisons of calculated depth ranges obtained from all geophysical techniques correlate well and validate the result (Table 1). The geological borehole data at pipe 1 and pipe 2 reported by the Geological Survey of India are well corroborated with our combined geophysical study.

Jan 17, 2024

By Gordon Kidd

Inflation and burgeoning costs are two among many factors which have generated a new surge of interest in "fringe benefits" (sometimes referred to as "supplementary remuneration" or "supplementary compensation"). Other specialized forms of compensation ("perks", in the vernacular) such as company cars, windowed offices, etc., which also are the subjects of current study, are outside the scope of this paper. For businesses, interest in fringe benefits is based on concern for employees? welfare, compliance with government requirements, and an increasingly burdensome impact on bottom lines. In 1980, according to Fred D. Lindsey in the October 1980 issue of Nation's Business, employee benefits will cost American employers an estimated $420 billion. To paraphrase Winston Churchill, "some fringes!" Indeed, few if any administrators consider employee benefits as fringes. Employee benefits impact other major areas of a company's operations as well. As listed by Beadle (1980), these areas include employee relations, collective bargaining, short-term costs, long-range funding, manpower planning, compliance with legislation, taxation for the company and for the employee, corporate image in the community, competitiveness for staff, communications, administration, claims cost containment, etc., etc.

Jan 1, 1980

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By Summers D. A.

A mining machine has been designed and fabricated to mine coal from room and pillar operations combining high pressure waterjet cutting and mechanical fragmentation. Waterjets are used to slot the coal face with an advancing plow wedge then breaking out larger coal pieces. The machine has the following advantages: - simply built around a disassembled longwall chock and gathering arm loader apron; - few moving parts which are simply and inexpensively maintained; provides immediate roof support in the face working area; - coal produced is larger, with resulting lower preparation cost; - no dust is generated; - risk of spark generation is virtually eliminated.

Jan 1, 1992

By C. J. Pritchard

The Office of Mine Safety and Health Research (OMSHR) investigated ways to increase mine airflow to underground metal/nonmetal (M/NM) mine working areas to improve miners? health and safety. One of those areas is controlled recirculation. Because the quantity of mine air often cannot be increased, reusing part of the ventilating air can be an effective alternative, if implemented properly, until the capacity of the present system is improved. The additional airflow can be used to provide effective dilution of contaminants and higher flow velocities in the underground mine environment. Most applications of controlled recirculation involve taking a portion of the return air and passing it back into the intake to increase the air volume delivered to the desired work areas. OMSHR investigated a Nevada gold mine where shaft rehabilitation was in progress and one of the two main fans was shut down to allow reduced air velocity for safe shaft work. Underground booster fan operating pressures were kept constant to maintain airflow to work areas, inducing controlled recirculation in one work zone. Investigation into system behavior and the effects of recirculation on the working area during times of reduced primary ventilation system airflow would provide additional information on implementation of controlled recirculation into the system and how these events affect M/NM ventilation systems. The National Institute for Occupational Safety and Health monitored the ventilation district when both main fans were operating and another scenario with one of the units turned off for maintenance. Airflow and contaminants were measured to determine the exposure effects of induced recirculation on miner health. Surveys showed that 19% controlled recirculation created no change in the overall district airflow distribution and a small reduction in district fresh air intake. Total dust levels increased only modestly and respirable dust levels were also low. Diesel particulate matter (DPM) levels showed a high increase in district intake mass flow, but minor increases in exposure levels related to the recirculation percentage. Utilization of DPM mass flow rates allows input into ventilation modeling programs to better understand and plan for ventilation changes and district recirculation effects on miners? health.

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years Minera Peñasquito, S.A. de C.V., a wholly owned subsidiary of Goldcorp Inc. has developed the Peñasquito property to produce an average annual production of 120 kilo tonnes of lead containing 0.5 million oz gold and 30 million oz silver and 250 kilo tonnes of zinc containing 20 thousand oz gold and 1.5 million oz silver.. The Peñasquito property covers a 39,000 hectare area in the western half of the Concepción del Oro district in the northeast corner of Zacatecas State, Mexico, approximately 24°45'N latitude/101°30'W longitude. The sulfide reserves are 1,009 million tonnes containing 3.33 million tonnes of lead, 7.26 million tonnes of zinc, 16.5 million ounces of gold and 1,000 million ounces of silver. This paper describes the work to justify the installation of HPGR to process the crushed SAG mill pebbles. The SAG mill-Ball mill and Cone crusher (SABC) grinding circuit is an accepted grinding circuit to optimize power consumption relative to throughput. The installation of a HPGR to process the Cone crusher product is the next step in optimizing the power consumption relative to throughput. The concern expressed by some on not moving on this change in grinding circuit was the capital and operating cost of a HPGR. The pebbles from the SAG mill can be the more abrasive and are the harder particles of the ore. Goldcorp investigated the wear and processing costs of installing a HPGR to treat the crushed pebbles. The conclusion was the installation would be a very positive economic factor in the operation of Peñasquito. This is the first application of the use of HPGR to process crushed pebbles. Minera Peñasquito and M3 Engineering selected Polysius to provide a Polycom 2417 with twin 3,000 kW drives. A comprehensive test program at Polysius has shown for 7% higher circuit power it is possible to get approx 23% higher tonnage. This coupled with full utilization of the SAG and Ball Mill available energies and with proper control of the transfer size from the SAG to Ball mill circuit there is the potential to achieve 65,000 mtpd per line or a 30% total capacity increase. The cost of power for this increase in grinding capacity is 4.8 kWh/tonne.

Jan 1, 2010

By Jim V. Rouse

Adverse water-quality impacts of uranium mining and milling activities on both surface- and ground-water resources in the Grants Mineral Belt have recently been documented.1 In some cases, the impacts resulted in violation of existing regulations and license conditions and have endangered public health. Unfortunately, industry-sponsored ground-water monitoring programs do not adequately record the actual impacts of mining and milling on ground-water quality.

Jan 1, 1976

By Robert McIvor

The following is a summary of the Robert H. Richards Lecture on “Learning and Good Fortune on the Road to Discovery” presented at the Mineral & Metallurgical Processing Division (MPD) Awards Plenary Session on Feb. 23, 2026 during the MINEXCHANGE 2026 SME Annual Conference & Expo in Salt Lake City, UT.

Mar 1, 2026

By D. E. Healy

In 1989 an Autogenous Grinding Task Force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding at the National Steel Pellet Plant located in Keewatin, Minnesota. Pilot plant test work performed by the Hanna Research Center (HRC) indicated that fully autogenous grinding with pebble extraction and crushing could feasibly be incorporated into the existing circuits. In 1990, one of the existing ten grinding mills was converted for an in-plant test incorporating pebble crushing. The full scale test work conducted in 1990 and 1991 verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit utilizing pebble crushing being greater than throughput of the existing SAG mill circuits.

Jan 1, 1992

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By Adabala Raja Venkata Sai Naresh, Radhakanta Koner

Particle size distribution (PSD) is an essential parameter in assessing the overall efficiency of blasting operations in mines and the subsequent mine-to-mill process in the mining industry. Despite some drawbacks of 2D image analysis techniques in accurately estimating particle sizes in PSD, the mining industry has relied on them for the last three decades. This study proposes the 3D rock fragmentation measurement (3DFM) technique for deducting the accurate dimensions of 3D rock particles for the PSD. 3DFM has utilized different processing algorithms. Images of different views of the non-touching rock particles of varying sizes have been acquired as a data acquisition step of structure from motion technology for generating sparse point cloud. Dense point cloud reconstruction is used to avail finer details of the point cloud using clustering views for the multi-view stereo algorithm. Random sample consensus (RANSAC) algorithm coupled with an unsupervised classification using the density-based spatial clustering of applications with noise (DBSCAN) classifier is employed to extract the rock clusters from the 3D point cloud. Finally, the accurate rock sizes are derived using the hybrid bounding box rotation identification (HYBBRID) algorithm with a root mean square error (RMSE) of 0.10 cm for length, 0.10 cm for breadth, and 0.32 cm for depth. The PSD of rock fragments obtained from the proposed 3DFM technique is found to be matching with the results of mechanical sieving and manual gauging with an R2 values of 0.98 and 0.99, respectively. The 3DFM method can be considered cheaper, more accurate, and computationally faster in determining the rock dimensions for the PSD determination method to enhance the productivity of the mining industry.

Dec 29, 2023

By Alistair James, James Alcorn, Chaitan S. Sandhu, Andy Small

The Risk-Informed Decision Making (RIDM) working group is a group of industry professionals formed under the joint initiative undertaken by United States Society of Dams (USSD), Tailings Dam Safety Committee and Canadian Dam Associations (CDA) Mining Dam Safety Committee (MDC). The working group was organized to develop a guideline on implementation of a RIDM process relating to the design of mining water dams and Tailings Storage Facilities (TSF). Since its formation in 2022, the group has completed a literature review of more than one hundred (100) cross industry publications on applications of RIDM in mining water dams and TSFs, has held two industry workshops in Niagara Falls, Ontario in 2024 and Saskatoon, Saskatchewan in 2025 to capture industry input relating to the understanding and application of RIDM. The working group has subsequently formulated a process that constitutes good industry practice as it relates to application of RIDM in mining dams and TSFs. The authors, through their engagement and leadership in the working group and facilitating the two industry workshops in 2024 and 2025, are of the opinion that the successful application process of RIDM across Canada and United States (U.S.) is still not clear to many industry practitioners. There is confusion over terminology, good versus poor RIDM, and in some cases reluctance to use the RIDM terminology. This paper addresses critical knowledge gaps identified in the RIDM implementation for mining water dams and TSFs through three years of stakeholder engagement. It provides clarity of the process via a joint position statement and implementation roadmap, resolves terminology confusion, and documents contradicting industry opinions to promote adoption of good RIDM practices in Canada, U.S. and beyond.

Feb 22, 2026

By J. J. Reilly

The Vesta Mines of the Jones & Laughlin Steel Corporation operate in the Pittsburgh Seam in Washington County, Pennsylvania. This seam is overlain with a drawslate, 12" to 16" in thickness, which slimes readily when wet. Because of the need for a uniformly good quality metallurgical coal, the amount of reject, together with the top and particle sizes of the raw coal feed, is a serious problem at the Vesta Preparation Plant. The Preparation Plant operates two, seven and one-quarter hour shifts per day and processes 2,100 tons per hour of raw coal feed. The third shift is, used for planned maintenance of equipment. Since the water clarification equipment is so vital in insuring a uniform product, there is no alternative but that it be in operation at all times. To insure this continuous operation,. well-planned maintenance is a necessity. For years, Plant Management has kept performance records of the various units to determine the renewal dates of vital component parts, the length of wear, the various materials used in the manufacture of the equipment, and the labor cost for renewal. These records have been of inestimable help in planning an effective maintenance program to insure continuous operation of the various units.

Jan 1, 1959