Search Documents

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

By G. D. Mainwaring, Weng L. W, Lam Y. K.

The first power transmission cable tunnel in Singapore was the 2.6km long undersea tunnel between Pulau Seraya and mainland Singapore, constructed in the1980s. Ten years later, similar concepts were used for the Tuas Cable Tunnel. The tunnel, which includes a 2.2km long immersed tube section, was designed to accommodate 10power circuits of 400kV and 230kV capacity. It is fully equipped with sophisticated control and communication equipment, fire suppressant and life safety systems plus a maintenance vehicle which runs on tracks through the length of the tunnel. The paper discusses the planning, design, and construction of the Tuas tunnel, and the development of these concepts for future tunnels.

Jan 1, 2001

By V. M. Lepetic

Large tonnages of copper and molybdenum sulfide ore are treated by flotation. Substantial savings could be realized, particularly in high-capacity concentrators, by use of a simplified flotation technique involving lower reagent consumption. Chalcopyrite and molybdenite from some deposits can be floated by use of only a frother as a single flotation reagent; acceptable concentrate grade and recovery can be obtained. Separation of molybdenite from copper sulfides may become simpler and less costly. The genesis of the ore and the ions present in the flotation pulp liquid phase appear to be the major success-determining factors.

Jan 1, 1972

Microorganisms have been widely used for hydrometallurgical operation and effluent treatments(Smith, et. al., 1991a; Gadd, et. al., 1986; Darnall, 1986; Paponettis, et. al., 1991; Mihaylov, et. al., 1991; Rusin, et. al., 1991; Noble, et. al., 1991; Yang, et. al., 1991). In recent years there is a growing interest in using microorganism for flocculation of minerals fines and flotation collector (Smith, et. al., 1991b, 1991c; Misra, et. al., 1991a, 1991b, 1992a, 1992b). It is envisioned that the utilization of nonpathogenic microorganism and/or extracellular surfactant derived from microorganism as a flotation collector will replace some of the environmentally toxic flotation collectors and at the sometime improve flotation efficiency. The selection screening, and judicious selection of appropriate microorganism as flotation collector has been a challenge to process engineers. Over the past five years, continued research at the University of Nevada has shown that certain microorganism Mycobacterium phlei (M. phlei) can be a good flocculating agent and has potential to be used as a flotation collector (Dubel, et. al., 1992; Misra, et. al., 1991a, 1991b, 1992a, 1992b; Smith, et. al., 1991d; Chen, et. al., 1992a, 1992b)).

Jan 1, 1993

By A. Davis

Pit lake chemistry depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock versus oxidizable sulfide content, and the alkalinity of recharging ground water. In this paper, we assess the geochemistry of 11 existing pit lakes, ranging from the acidic Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington Pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits with the long-term pit lake chemistry lying on a geochemical continuum between end members consisting of influent calcium bicarbonate ground water, and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1996

By A. C. Smith, J. H. Rowland III

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) established a Technical study panel (the Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the belt evaluation laboratory test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 91 - 107 cm (36- to 42-in.) wide conveyor belt. Due to today’s coal haulage capacity, the mining industry is using 183 cm (72 in.) and wider conveyor belts. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2011

By Michael S. Moats, John Bailey Fletcher

The performance of grinding media can be misrepresented in marked ball wear tests due to galvanic interactions between dissimilar media. The possible galvanic interaction of media materials during marked ball wear tests has not been adequately explored. Corrosion rates and potentials of modern high carbon steel and high chromium white iron grinding media materials were measured using electrochemical testing as a function of pH and chloride content in a simulated mill water. The results replicate previous research with the high chromium white iron sample being more noble (higher corrosion potential) and corrosion resistant (small corrosion current) than high carbon steel. Using the experimental data and corrosion theory, the effects of galvanic coupling on corrosion rates were calculated to examine what could happen during a marked ball wear test or when a mixed media charge is present. This analysis indicates that high carbon steel can cathodically protect high chromium white iron leading to significant decreases in the corrosion rate (up to 99%) of this material during marked ball wear tests. The magnitude of the protection is a function of the pH of the mill water.

Dec 21, 2022

Never known as a conference to shy away from its share of off-color jokes, the Colorado Mineral Processing Division?s Annual Meeting returned to the Broadmoor Hotel in Colorado Springs, CO April 26-28 for its 62nd edition, this one held under the theme ?Does size matter (is bigger always better).? With the predictable jokes sprinkled in here and there, and a few unpredictable ones as well, the three-day conference featured a healthy mix of talks about some of the latest technical developments in the field of mineral processing, as well as insightful looks at some new operations in the western United States. This year, the Colorado MPD also launched the Wagner Equipment Student Scholarship program.

Jan 1, 2012

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999

By Ted H. Eyde

Improving the mineral industry&apos;s tarnished image describes in a nut- shell the reason why the Speakers Bureau of the Tucson Subsection of the AIME was formed. Let&apos;s go back in time about 3 years to the fall of 1971. Literally thousands of bills detrimental to the mineral industry were being introduced into Congress and State Legislatures. Unfortunately, many were being passed and signed into law. Clean air and water, zero pollution, preserve the environment, ecology, biodegradeable, wilderness were the words that the self- styled ecologists and environmentalists were preaching. The mineral industry either sat mute or in place of acting, reacted in a way certain to attract a maximum amount of bad publicity with a minimum amount of rhetoric. A mining company president, for example, commenting on the primary air standards in Arizona was reported by the press as having said, "we&apos;ll shut all the smelters down and put thousands of Arizonans out of work if we have to meet the Arizona standards." Or another defending a poorly planned highly visible open pit nonmetallics operation, "we&apos;ll take the whole mountain down if we want to, and nobody can stop us" and still another manager of Operations, "the bottom line is all that counts, to hell with all of this environmental nonsense."

Jan 1, 1975

By J. M. Mutmansky

A number of previous publications have attempted to provide the practicing ventilation engineer with simple guidelines on the optimal velocity to be used in mine openings. Some of these velocities were meant to be used in metal mining operations and some were meant for coal mining. A careful review of these publications reveals that the optimal velocities were determined based upon assumptions that are not existent today. As a result, they are not suitable for use in a modern coal mine. This paper takes a new look at this problem and determines a statistical relationship for optimal velocity that can be applied under both current and future conditions. The analysis performed here is based upon the determination of the optimal velocity for coal mine entries under variations in power cost, mining cost differential, airway friction factor, time value of money, airway lifespan, and quantity of air carried. A total of 8400 different conditions were analyzed for optimal velocity using computer calculation of the capital and operating cost values. Using the individual values of the optimal velocity derived in the calculations, a linear regression equation was fitted to the data to relate the optimal velocity to the other six variables outlined above. This regression relationship allows the ventilation engineer to make an easy, rapid determination of the optimal velocity.

Jan 1, 1984

By J. A. Lepinski

The FASTMETSM Process is a coal-based process for converting iron oxide fines into metallic iron. The end product, direct reduced iron (DRI) is used as a low residual charge material in electric arc furnace steelmaking. This paper describes the FASTMET Process and its potential application in the United States. Operating results from a 175 kg/h process simulator are presented. Characteristics of the end product are discussed. Process economics are reviewed along with plans for scaling-up the process to full commercial size.

Jan 1, 1993

By Keith A. Heasley

At this point in time, approximately 800 M tonnes (880 M tons) of coal are mined each year in the United States. Forty percent of this coal or approximately 320 M tonnes (350 M tons) is taken from underground coal mines, and from this subtotal 16% or 50 M tonnes (55 M tons) is from longwall panels (1). If, for the sake of argument, an aver- age extraction thickness of 1.5 m (5 ft), an aver- age extraction ratio of 50 percent and an in situ density of 1360 kg/ms (85 lb/ft3) for this coal are assumed, then the 320 M tonnes (350 M tons) of underground coal translates to over 310 km2 (76,000 acres) that is undermined each year. Con- sidering that the total U.S. production of under- ground longwall coal to date is approximately 345 M tonnes (380 M tons), then a total of approximately 165 km2 (41,000 acres) (considering 100% extraction) has been directly undermined by longwall coal production in the United States. If the angle-of- draw is considered, the total area affected by longwall subsidence in the United States is probably twice the above value or 330 km2 (82,000 acres) . In the future, a number of other miscellaneous factors seem likely to multiply the number of potentially damaging situations that occur due to longwall coal mining. First, the overall production of coal in the United States is expected to gradually increase. This factor is further com- pounded by both the fact that the percentage of the overall production due to underground mining is bound to increase, since the vast majority of U.S. reserves (68%) are only recoverable by underground methods, and the fact that the percentage of the underground production of coal that is recovered by longwall mining is drastically increasing (1). Finally, as the nicest underground reserves are depleted, the remaining reserves will tend to be deeper, which increases the affected surface area, and under denser population concentrations, which increases the likelihood and severity of possible damages. Overall, considering the number of factor which are biased towards increasing the amount of undermined acreage, it appears that there must certainly be a corresponding increase in the number of possible damaging situations due to longwall-induced, ground subsidence.

Jan 1, 1986

By M. Michael, A. Felber

"Mining activities, especially underground mining operations, create great demands on utilized haulage means which cover a variety of different horizontal and vertical distances. In the course of the continuous optimization of the haulage process, the application of textile machine elements, in particular synthetic fiber ropes, offers new opportunities. Therefore the current level of knowledge needs to be improved based on extensive analyses. For the estimation of the scope of these analyses, different fields of application and occurring environmental influences which have an impact on synthetic fiber ropes during their use in underground mining have to be evaluated. The Chair Underground Mining Methods of the TU Bergakademie Freiberg works on a scientific project concerning the use of synthetic fiber ropes in underground mining operations. This paper focuses on the potential application of synthetic fiber ropes in haulage systems in underground mining and exposes critical influences as an outcome of the working environment. These first investigations are the basis for the development of an appropriate experimental series. SYNTHETIC FIBER ROPES FOR UNDERGROUND MINING OPERATIONS The main idea is to optimize underground haulage means to develop even more economic systems. The new and lightweight design of single machine elements seems to be the first step to accomplish this goal. An example is the lightweight design of shaft hoisting ropes. The commonly used steel wire ropes are very heavy and are endangered to snap due to their own weight when reaching a distinguishing length. Thus they may not or only conditionally be used for deep mining operations utilizing shaft haulage. Ropes made of high-tech synthetic fibers weigh only an eighth of steel wire ropes while displaying the same tensile strength. This relation is shown in Figure 1, based on the comparison of fiber strength and density. This could offer new opportunities for deep mining operations, which are anticipated by many mining companies. /1/"

Jan 1, 2015

By M. A. A. de Klaver

Functional Description Figure 1 is a typical flowsheet for a system for solid fuel addition to filter cake. Solid fuel, coal, coal breeze, or charcoal, is fed from a,stockpile to a surge hopper. The solid fuel is metered into a grinding mill. The fuel is dried and ground in a grinding mill. The on-size particles are removed from the mill by air sweeping. The ground solid fuel is separated from the air stream by a cyclone and stored in a surge hopper. The ground solid fuel is then pneumatically conveyed to a small hopper in the balling area. The fuel is proportioned into the filter cake just prior to mixing. An efficient mixer is very important to have a successful operation. The exact flowsheet would depend on a number of factors including what fuel is used, how the fuel is received, and the cnaracteristics of the fuel as received. Availability of floor space in the plant may also affect the flowsheet. For example, drying air may be supplied from the pellet furnace if the grinding mill can be located near the grate, or the pneumatic conveying system and a surge hopper may be eliminated by placing the grinding mill adjacent .to the mixing area. Also, for a multiple line plant, a ball mill rather than a roller mill may be more suitable.

Jan 1, 1980

By K. V. Raj, A. Miller

"Workers at mineral processing facilities are often exposed to high levels of dust generated when ores are processed. Crushing, grinding, screening, and other processes generate large quantities of dust, which can exceed the threshold VALUES (prescribed by the Mine Safety and Health Administration (MSHA). Many ores contain quartz (silica), which has been known to cause serious health problems in workers over time. Given the structure of mineral processing plants, the airflow regime is not coherent inside the building, which may lead to multiple recirculation zones. These recirculation zones can trap dust, and concentrations of dust can then rise over time. Therefore, there is a need to understand the airflow phenomenon that occur inside of mineral processing facilities and how these occurrences interact with the dust generation processes to identify zones of potentially high dust concentration. Computational fluid dynamics (CFD) modeling can give a better understanding of the airflow and help recommend designs and methods to mitigate the high dust concentrations in a mineral processing plant. This paper presents the CFD modeling of airflow inside of a mill building to demonstrate airflow patterns that will affect the generation and subsequent dispersion of dust due to crushing, grinding, and other activities. This study was conducted by researchers from the National Institute for Occupational Safety and Health (NIOSH). INTRODUCTION In a mineral processing facility, minerals go through various mechanical processes in order to reduce their size for separation of economic minerals from gangue minerals to produce a final marketable product. This research, conducted by the National Institute for Occupational Safety and Health (NIOSH), focuses on ore mills in metal and nonmetal mining (MNM) operations, but the applicability of the approach will be valid for any large structure where workers are exposed to airborne contaminants. The processes of crushing, grinding, cleaning, drying, and product sizing in these facilities generate a large amount of dust, creating hazardous conditions for the workers in these facilities. This is highlighted by the fact that MSHA sampling data for the years 1997–2012 indicate that 12.3% and 15.9% of the gathered samples were over 100 µg/m3 for silica for metal and nonmetal mills, respectively [1]. Mineral processing operations typically use some type of engineering control to address their most significant dust sources. Engineering controls include such approaches as bag-house-type dust collectors, scrubbers, and electrostatic precipitation [2]."

Jan 1, 2018

By T. G. Carnahan

The U.S. Department of the Interior, Bureau of Mines, performed a laboratory-scale investigation of technique for recovering silver from pregnant solutions generated in the hydrometallurgical treatment of complex base-metal sulfide concentrates with oxidizing chloride media. This provides a means for recovery and simplified reduction of accessory silver to metal from ions. The method consists of adding NaI or KI to the solution to precipitate AgI, which is then contacted with Na2S to produce Ag2S and to regenerate the iodide salt solution. Silver recoveries range from 99 pct with 20 pct excess iodide precipitant, to-92 pct when the theoretical stoichiometric amount of precipitant is employed. The Ag2S product can be reduced to silver metal by contact with aluminum chips in NaOH solution followed by purification with conventional fire refining techniques.

Jan 1, 1980

By S. Que

Local community acceptance is a key aspect of planning and managing mining projects, whether through sustainability assessment and reporting or corporate social responsibility programs. However, there has been very little research to understand the determinants of community acceptance. This paper seeks to identify key mine characteristics and demographic factors that influence individual acceptance of mining projects. Six demographic factors and 16 mine characteristics were selected based on literature review. Four of the six demographics factors were confirmed to be significantly (p < 0.05) correlated with people?s attitude of the importance of the mine characteristics. All sixteen mine characteristics are identified as important factors. The most important mining factors are Job opportunities, water shortage or pollution, air pollution and land pollution. Both the mining and control groups have same opinion of 12 mining characteristics and differ on four (infrastructure improvement, labor shortage for other businesses, noise pollution, and mine life). During design and management of mines, this data can be used as a reference. This result will facilitate better choice experiment (survey) design for discrete choice modeling. Such discrete choice models can provide a viable framework for data-driven community engagement and sustainable mine management.

Feb 23, 2014

Within the research project "Mine Development" funded by the "Austrian Fonds zur Forderung der wissenschaftlichen Forschung (FWF) " (funds for scientific research) between 1991 and 1993 150 underground hardrock mines in Europe, Northern America, Australia and Japan have been visited to analyze their general design and layout. The main aim of the project was to develop strategies for accessing new underground hardrock mines and to establish a mine planning database. The investigation included mines in high developed countries only, with a comparable labor cost situation. This paper presents the results of one part of the project, which deals with investigations into the influence of different parameters on the design of the primary access for a mine.

Jan 1, 1995