Search Documents

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

Among underground coal miners, roof bolter operators are generally considered to have some of the highest risks for hazardous respirable dust exposure. This is because bolting requires drilling into roof strata that can often be a source of silica and silicate dust, which are associated with occupational lung diseases. However, little is known about the variability of dust characteristics (e.g., mineralogy constituents, particle size) in the vicinity of the bolter—or when specific dust controls are applied. As part of a prior NIOSH study, respirable dust samples were collected during several different events in standardized locations around an active roof bolter, and personal samples were also collected from the operator during the cleanout of the bolter’s dust collection system when it was equipped with a novel wet dust box versus a traditional dry box. Those samples were made available for follow-up analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDX), as well as direct-on-filter Fourier transform infrared spectroscopy (FTIR). Results showed variability in dust constituents and particle sizes at locations around the roof bolter, and indicated some event-to-event differences in dust sources. Additionally, compared to the dry dust box, the wet dust box appeared to reduce (by 41–82%) the relative silica and silicate content in the respirable dust to which the operator was exposed during cleanout. Furthermore, an inter-laboratory comparison demonstrated the reproducibility of a standardized direct-on-filter FTIR method for estimating quartz mass (i.e., the predominant form of crystalline silica) in respirable coal mine dust samples. However, for constituent analysis by SEM–EDX, differences observed between results from two independent labs indicate that standardization of the analytical protocol is necessary to enable comparability of results.

Jan 5, 2024

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009

By Roger J. Araujo

A photochromic material is one which undergoes a change of color when exposed to light and reverts to its original color when the light is removed. Review articles carrying extensive bibliographies have been written by Brown and Shaw (1) and by Schwab and Bertelson (2). Organics. Schwab and Bertelson divide the reactions in different organic photochromic materials into some half-dozen categories; Windsor (3) reduces these to the following three main classes of general interest, based on how they work. 1. Stereoisomers. Absorption of light breaks one of the chemical bonds in a. ring molecule, thus allowing the molecule to unwind and form a different geometrical arrangement. The reverse process is a reforming of the bond. Examples of this class are the spiropyrans and the anils. 2. Dyes. A triphenyl methane dye, for example, is oxidized by energetic light; the absorption characteristics of the positive ion so formed are different from those of the original electrically neutral benzene rings. 3. Triplet States. In the class of polynuclear aromatic hydrocarbons, ground-state molecules are excited first to a singlet state by irradiation, and then go, via the lowest triplet state, to an excited triplet state. Visible light is absorbed in the triplet-triplet transition.

Jan 1, 1970

By E. Molleman

This paper reports on testwork exploring the dissolution/reprecipitation reaction: ZnS + 2HCl ? ZnCl2 + H2S, as part of a process for the production of pure ZnS. In spheroidal form, this would constitute a premium fonn of zinc refinery roaster feed enabling the production of pure ZnO. The research focused on the influence of proton activity on dissolution of zinc concentrates from Brunswick Mining & Smelting, Red Dog and Tara. The results and thermodynamic data suggest that the three concentrates contained significant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1997

By M. J. Allan, D. J. Barratt

This paper reviews current testing methods for sizing autogenom and semiautogenom mills in the North American context with comments on the necessity for test work and requirements for different circuits and equipment selection. The economics of testing and the value received are discussed.

Jan 1, 1987

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By Shawn Orser, Jennifer Waddell, Mike Sierakowski, Tom Barrett

Production evaluations were conducted at Daisy Gold Mine (Glamis Gold, formerly Rayrock), between August, 1997 and August, 1998 to quantify the effect of 3M fluorochemical surfactants (fluorosurfactants) on extraction kinetics and gold recovery in gold heap leach mining operations. Ore was treated at a level of 7-10 grams surfactant per ton of ore using 3M Pluorad TM Leach Mining Additive PC-GOLD. Kinetics and gold recovery were determined by solution assay for each of the tests. Both tests indicated improved kinetics, and data from Test 2 was used for determination of a quantitative increase in gold recovery resulting from PC-GOLD addition. A discussion of test results including methods used to determine gold recovery is provided.

Jan 1, 2000

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By A. Juganda, F. WILSON, H. PINHEIRO, N. SANDOVAL, J. F. Brune, G. E. Bogin Jr.

To evaluate methane explosion hazards in longwall coal mines, a CFD model was developed along with a 1/40th-scale, optically accessible model of an underground longwall coal mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met for accurately representing the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure, and gas concentrations. This research will help develop strategies for methane monitoring that prevent methane ignitions and explosions in longwall coal operations.

Aug 15, 2022

By J. C. Stankus, K. J. Ma, D. Faulkner

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding-type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high, causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concern for the U.S. Mine Safety and Health Administration (MSHA) and ground control engineers. During the last few years, Keystone Mining Services, LLC developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents an impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development and laboratory testing of a waterproof coated impact-resistant lagging panel and (3) impactresistant steel set design based on the law of conservation of energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Shiou-Chuan Sun

This paper is to be presented at the Annual Meeting of the American Institute of Mining, Metallurgical and Petroleum Engineers, New York, New York, February 18-22, 1962. Permission is hereby given to publish with appropriate acknowledgments, excerpts or summaries not to exceed one-fourth of the entire text of the paper. Permission to print in more extended form subsequent to publication by the Institute must be obtained from the Secretary of the Institute. If and when this paper is published by the Institute, it may embody certain changes made by agreement between the Technical Publications Committee and the author, so that the form in which it appears here is not necessarily that in which it may be published later.

Jan 1, 1962

By Zhenzhong Bian, Ruiyang Zhang, Xiaofeng Zhong, Zhangxuan Ning, Yuanping Zhang, Jie Lu, Airan Zhang

This study addressed the separation and recovery of vanadium(IV), iron, and titanium from synthetic and real leach solutions of vanadium-bearing titanomagnetite using extractant P204 (di-(2-ethylhexyl) phosphate) and P507 (2-ethylhexyl hydrogen- 2-ethylhexyl phosphonate). Based on the speciation analysis of vanadium in sulfuric acid medium, the single-stage extraction efficiency of vanadium, iron, and titanium was 94.21%, 3.45%, and 5.32%, respectively, under the optimal extraction condition of P204-P507 concentration of 15% (v/v), P204 to P507 ratio of 3:1 (v/v), TBP (Tributyl phosphate) concentration of 5%, sulfonated kerosene concentration of 80%, initial pH of 1.8, contact time of 8 min, and phase ratio (O/A) of 2:1. By confirming the predictions of the McCabe-Thiele diagram, a five-stage countercurrent extraction was carried out and the desirable extraction efficiency for vanadium reached 98.13%. The maximum co-extraction coefficient and distribution ratio of vanadium were 2.58 and 26.23, respectively. The stripping efficiencies and concentrations of a vanadium-rich solution by three stages of countercurrent experiments with 20 vol.% sulfuric acid reached 99.14% and 0.58 g/L, respectively, while almost all of the titanium remained in the organic phase. The mechanism of synergistic extraction between hydrogen ions of P–O–H and VO2+ in acidic conditions was confirmed by ATR-FTIR spectroscopy and molecular structure derivation. Besides, the separated impurity ions ( Fe2+) after oxidation, precipitation, and roasting process form a qualified iron oxide pigment with a total iron content of 97.2%.

Apr 25, 2023

By Rudrajit Mitra, Erik Hulthén, TOBIAS HARTMANN, ELISABETH CLAUSEN, Aarti Sörensen

There has been an ongoing debate on how to transform engineering education to better prepare students for today`s professional world that is characterized by increasingly complex problems and challenges that engineers are tasked with upon entering the industry. Within the conceive–design–implement–operate (CDIO) framework, entrepreneurship education presents a valuable pedagogical approach to foster the necessary skills of the students through integrated, hands-on, active learning experiences. While numerous publications have addressed possibilities of how experiential, problem-based, project-based and active learning can be integrated into engineering curriculum, there has been hardly any attention on mining engineering with respect to adopting this approach. This paper will address the possibilities of integrating entrepreneurship education into mining engineering programs in particular. This paper will enhance and foster discussion among academics from mining engineering on how to integrate elements of entrepreneurship education on a course, program and departmental level to infuse value creation experiences across the curriculum.

May 25, 2022

By P. I. James, M. R. Baker

Este artículo analiza la nueva producción de cobre a partir de "minerales de desecho" de baja ley usando la tecnología de Blue Planet Strategies DEMET™ (Dynamic Electrode Mining Effluent Treatment, por sus siglas en inglés), que tiene como objetivo salvar la brecha de procesamiento entre la solución débil de lixiviación en operaciones de extracción por solventes/electrowinning (SX/EW), removiendo electroquímicamente los metales a partir de corrientes débiles y a la vez generando productos concentrados en metales objetivo en un análogo funcional de extracción por solventes (SX). Se estudió el tratamiento de la débil solución de lixiviación pregnant (PLS por sus siglas en inglés) y se usó para estimar los impactos económicos y de producción para una hipotética lixiviación en pilas de cobre brownfield y una operación aumentada DEMET usando SX/EW para tratar el "mineral de desecho." Se presenta la remoción de cobre a un 86% de eficiencia en las placas por debajo de 0,1 g/L de cobre con un consumo de energía de 0.55 kWh/lb de cobre y una concentración del producto mayor a 10 g Cu/L. El modelamiento arrojó aproximadamente $2/ lb para la producción total de cobre y costos de tratamiento menores o iguales a $1/lb con un inmediato aumento del margen bruto de operación del 12% para el brownfield incrementado. Se indicó también un aumento de la vida de la mina con un margen bruto promedio de 38% en la producción aumentada de "mineral de desecho" con valores de cobre de $3.25/lb.

Jan 1, 2014

By J. Pascoe, J. H. van Laar, J. H. Marais, F. J. L. Matthee

Advanced measurement and verification (M&V) is a process where the impact of an energy initiative is determined in real time. Data prediction models can be used to predict and compare energy consumption with a predetermined baseline. Deeplevel mines can benefit from advanced M&V as the impact of operational changes can be identified in real time. Ultimately, this can ensure that informed decisions are made regarding energy management based on the impact and severity of the occurrence. Previous studies on advanced M&V do not account for operational changes to the model’s baseline. These changes can significantly impact the performance of both the mine and related activities. The aim of this study is to propose a method that can accurately predict the energy consumption of a deep-level mine regardless of operational changes. To achieve this objective, nine different data predictive modelling techniques were considered. The proposed method is based on the Moving Average (MA) modelling technique due to its simplicity, flexibility, and rapid development time. The coefficient of variation for the root mean square error (CV(RMSE)) was used to statistically analyse the modelling error. If the predictions exhibit an unsatisfactory CV(RMSE), the model dynamically adjusts to reduce the prediction error. The model was developed to adapt to operational changes in scenarios where the standard model becomes irrelevant. The method developed in this study was able to predict the future energy consumption of deep-level mines with an accuracy of 99%, improving the mine’s energy and finance management.

Dec 13, 2023

By Russell Frith

The entire subject area of micro-seismic events due to stored strain energy, as distinct from gas-driven coal outbursts, can be readily sub-divided into firstly events with their energy source from within the coal seam (termed “bursts”) and secondly, event with their energy source outside of the coal seam in either the overburden and/or floor strata. The reason for sub-dividing micro-seismic events in this manner is that if the causation mechanisms and associated geotechnical conditions are materially different, then effective pre-mining predictions and subsequent operational controls may also differ. Attempting to explain a multitude of micro-seismic event types without consideration of varying source mechanisms will inevitably lead to inadequate causal explanations and effective controls.

By Lorraine Brandt Yde

This paper describes development of a cost report that is descriptive, logically oriented, and concise. Since the costs involved relate to mining, this reporting technique could help bridge any possible communications gap between "mining men" and computer personnel, at the same time giving the computer-oriented mining individual information to assist him in his job performance. As computers become entrenched in the mining world, meaningful report assimilation becomes a major task. No one should be more capable of defining required results than the man requesting a report. If he is able to clearly state his needs and has researched his problem, it will be reflected in the computer output. During 1970, The Anaconda Company's Berkeley Pit Operation, at Butte, Montana, received many different computer-generated equipment cost reports. Up to thirty-six different components for each type (class) of pit equipment contributed cost data to the Berkeley Pit cost system files for both operating and repairs during current month, year-to-date and accumulation-to-date time periods. This reporting approach was taken to facilitate analyzing this voluminous data. SUMMARY A Major Component Cost Analysis (Exhibits 6-A thru 6-C) developed by arranging the top ten operating and repair percentages (component cost divided by total cost) in descending order, and then accumulating these percentages to a possible one-hundred percent. While tabulating the operating and repair cost percentages by equipment unit number in the current month, year-to-date and accumulation-to-date time periods, a frequency chart is constructed for each equipment

Jan 1, 1971

How do you think the US Bureau of Mines closing will affect SME? The demise of the bureau represents a challenge, an opportunity and, above all, new responsibilities for our profession. A lot of good professionals are seeking new positions. A lot of worthwhile research is available for transfer to the private sector. Logic dictates that worthwhile projects of any defunded government activities should find support in the private sector. The bureau may be gone but its legacy is deeply rooted in the profession. The bureau’s contributions will be remembered as long as there are mines and miners. Its1994 research program was divided into three major areas: environ-mental technology; health, safety and mining technology; and minerals and materials science. There must be a place in either the government or private sector to continue these worthwhile activities.

Jan 1, 1996

By C. Bryce

Rhenium is primarily recovered as a by-product from molybdenum roasting circuits. However, rhenium is also present in copper heap leach solutions at very low concentrations and represents a potential new rhenium source. Freeport-McMoRan Copper & Gold has developed a new process using carbon adsorption followed by ion exchange or solvent extraction to concentrate rhenium from less than 1 ppm to 15 g/L. The product is compatible as a feed to an existing rhenium processing plant. A pilot plant operated at Freeport-McMoRan?s Sierrita mine has demonstrated the technical and financial feasibility of this new process.

Feb 23, 2014

By C. D. Anderson

"IntroductionTungsten carbide is a valuable material used in a variety of different applications, including the manufacturing of cutting tools, bearings and as a cost-efficient alternative to industrial diamonds. Both the high hardness value (Mohs 9) and scratch resistance of this material make it a valuable commodity for use in the mining industry.Usually, the production of tungsten carbide is a multistep process involving one or more of the following unit operations: hydrometallurgical digestion, solution purification, crystallization (as ammonium paratungstate), calcination, hydrogen reduction and carbon synthesis. The proposed three-step process eliminates three of these steps (crystallization, calcination and hydrogen reduction) by implementing a combination of hydro/pyrometallurgical techniques. These include alkaline pressure leaching, carbon adsorption and carburization roasting. By eliminating some of the intermediate processing steps, there is potential to reduce energy consumption and decrease overall operating costs.Methods and resultsInitially, alkaline pressure leaching with sodium carbonate (Na2CO3) was employed to selectively leach tungsten, as tungstate (WO4 2-), from an industrial Scheelite (CaWO4) flotation concentrate. Experimental variables included lixiviant (Na2CO3) concentration, temperature and residence time. Experimental constants, based on previous work, were percent solids at 13 wt% and agitation at 400 rpm (Queneau and Strathmore, 1969). Leaching results showed it was possible to extract 97% of the tungsten present. The most favorable conditions for leaching were determined: 2M Na2CO3, temperature of 180° C and a residence time of 30 minutes."

Jan 1, 2015