Search Documents

By R. A. Jankowski, J. D. Potts

Four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner section averaged 0.59 and 0.26 mg/m3, respectively. The stageloader/crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feederbreaker contributed 0 to 0.2 mg/m3 of dust. A 1000 ft (305 m) increase in belt entry length or a 200 to 500 tons/shift (181,000 to 454,000 kg/shift) increase in production resulted in roughly a 0.1 mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By J. K. Grunig

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1982

By D. A. Rice

In pelletizing magnetic iron ore concentrates, about 6 to 18 lb of bentonite binder are added per ton of concentrate during balling to give green and dry strengths to the unfired pellets. The dry bentonite is mixed into the filtercake following the magnetic concentration circuit of the plant. The filtercake contains about 10% moisture, and the water may be of highly variable composition, depending on the particular concentration circuit, its source, and the ore being treated. A knowledge of the parameters that influence the balling operation is essential for optimal efficiency in producing balls strong enough to survive the treatment during transportation from the balling device to the furnace and during the firing operation. Furthermore, very weak unfired pellets probably contribute to high dust losses and poor furnace control. The factors that determine the strength of unfired pellets have received considerable study (1,2,3,4). Tigerschiold and Ilmoni(l) pointed out the significance of the surface area of the particles being pelletized. Merklin and Childs(2) reported on the effect of material size consist, chemical additives such as soda ash, lime, balling time, ball size, and the moisture content of green balls. Iwasaki and Zetterstrom(3) examined the detrimental effects of fatty acids on the pelletizing process. Stone(4) correlated the zeta potential of bentonites with the strength of unfired pellets. He found that, in general, a high negative charge on the bentonite is conducive to good balling. Although studies of pelletizing in the iron ore industry deal with a complex multicomponent system consisting mainly of the iron mineral, bentonite, and water, the last of these has received little attention, particularly with regard to the possible effects of mill water chemistry on the pelletizing process and the strength of unfired pellets. It is widely known that the composition of mill process water is an important variable in unit operations such as flotation, thickening, and filtering and that impure water can lead to poor metallurgical results. The results of the present study indicate that the chemistry of the mill water may be an important variable in the balling operation as well. Knowledge about this variable should contribute to lowering bentonite and oil consumption and to improving furnace performance. Such knowledge can also assist those who use balling in evaluating commercial bentonites for plant use as well as those investigating balling from a more fundamental point of view In this study we have examined 1) the effects of replacing mill process water in the magnetic concentrate filtercake with pure water, and 2) the effects of several chemical impurities that are commonly found in mill process waters upon the strength of unfired pellets. The results are interpreted in terms of the zeta potential of the bentonite and magnetite particles. The data lend support to a suggested mechanism whereby the electrostatic attraction of oppositely charged particle surfaces causes bentonite-bentonite and magnetite-bentonite bonding. This mechanism would also explain why several chemical additives e.g., sodium carbonates and phosphates, have such marked effects on increasing the strength of unfired pellets.

Jan 1, 1971

By Hai Lin, Renshu Yang, Yongliang Li, Shizheng Fang

With the aim of solving the large deformation problem of surrounding rock in coal mine roadways with a thin sand-mudstone interbed roof, transportation roadway 1603 in Haoyuan Mine was considered. The failure mechanism of surrounding rock was studied through comprehensive on-site investigations, borehole image analysis, mineral composition analysis, and other means. Numerical simulations were performed to determine the influence of roof layer thickness, lateral pressure coefficient, and coal rib strength on the stability of the interbedded roof. The main reasons for support failure and deformation of the roadway are softening and swelling of the sand-mudstone interbed roof upon exposure to water, insufficient support capacity of the roof due to the soft coal rib, an unreasonable support scheme, or poor construction quality, which can reduce the bearing capacity of surrounding rock. Based on our analysis, a control strategy was devised for a thin coal-mudstone interbed roof. The support scheme combines long and short cable support, strengthening of the coal rib to consolidate the roof, and partially shotcrete grout, and was found to improve the overall mechanical strength of surrounding rock and maintain the stability of the thin sand-mudstone interbed roof. The results of the numerical simulations and monitoring data indicated that the proposed support scheme effectively controls the deformation of the surrounding rock of thin sand-mudstone interbed roof of coal mine roadways while maintaining the safety and stability of the surrounding rock and supporting structure.

Dec 12, 2022

By A. M. Gaudin

A new method of measuring the viscosity of unstable suspensions has been developed, using a Heinz viscometer. The technique was applied to kaolin-water suspensions. Spreads in viscosity with lime additive were measured.

Jan 1, 1962

By P. G. Martin

"As the speed of business has continued to increase over the last decade, the focus on real-time control of the performance of both stationary and mobile assets has become an increasing priority. Traditionally the maintenance team has been focused on the management of the availability of assets while the operations team has been focused on the throughput of those same assets. Typically operations and maintenance teams worked almost independently in spite of the fact that they were both working with the same assets. Part of the problem has been their traditional performance measures which have often been diametrically opposed. Recent advancements in the area of real-time performance measures and decision support have helped to drive higher levels of collaboration between operations and maintenance leading to real-time asset performance control and higher levels of business performance. This paper will explore the forces driving the need for changes, present an effective approach to the definition of the most appropriate business performance measures, and examine the effectiveness of contextualized real-time decision support resulting in asset performance control. TRADITIONAL APPROACHES TO ASSET PERFORMANCE MANAGEMENT In most industrial operations the phrase asset performance management is synonymous with maintenance of the industrial assets. This is the way industry has viewed asset management and asset performance management for decades. This is a very limited perspective that is serving to constrain the profitability of industrial operations. As industrial organizations began to form following the Industrial Revolution, the complexity of the operations forced an organizational design based on specialization. No single person could understand all of the aspects of an industrialized operation. This was particularly true at the plant floor level where the operation and maintenance of the industrial equipment required very different skillsets and training. To accommodate the vast differences most industrial organizations set up operations teams to run the equipment and maintenance teams to keep the equipment available to the operation. Both teams were dealing with the same industrial equipment but from very different perspectives and with very different performance measures. Typically the operations team was measured on maximizing the output of the equipment – or throughput. On the other hand the maintenance team was measured on the uptime – or availability of the equipment."

Jan 1, 2015

By J. F. Burr, D. Snyder, W. Calder

"INTRODUCTION “Explosion protection” refers to techniques used to minimize the potential for electrical and electronic equipment to create an ignition while operating in a hazardous location (HAZLOC). In particular, U.S. coal mines are required to use equipment in certain areas of the mine that has been approved by the Mine Safety and Health Administration (MSHA) for use in a methane and coal dust environment to limit the risk of the equipment creating an ignition-capable spark or a thermal energy ignition. In general, MSHA’s regulations for explosion protection recognize two techniques: the use of explosion-proof enclosures (XP boxes) and 2-fault intrinsic safety for electrical and electronic equipment. For 2-fault intrinsically safe (IS) equipment, the U.S. mining industry requirements are unique in that the equipment is certified by MSHA. The criteria MSHA uses to evaluate equipment for intrinsic safety, as required by Title 30 of the Code of Federal Regulations (30 CFR) [30 CFR, Sections18.20(b), 18.68(a)(1), 19.1(b), 20.1(c)(2), 22.6, 23.6, and 27.20(a)], is published in a document referred to as ACRI2001 (1). Outside of U.S. underground mining, many industries and countries accept equipment that is designed to a consensus-based international standard (ANSI/ISA 60079-11 is the U.S. version). The purpose of this study is to provide an overall assessment of the ANSI/ISA 60079-11 standard on 2-fault intrinsic safety and the MSHA ACRI2001 acceptance criteria, and determine if the ANSI/ISA document can be an alternative to ACRI2001 while maintaining an equivalent or better level of safety for miners. There are many drivers for this study. First, immediately after the 2006 MINER Act (2) was passed, there was a perception in the industry that the unique MSHA requirements were contributing to delays or restricting the availability of equipment to meet the requirements of the Act. Additionally, the MINER Act required that mine operators submit an accident response plan for MSHA approval, to be reviewed every six months. MSHA is required to determine if these plans reflect the most recent credible scientific research and make use of currently commercially available technology. There is a concern, as expressed in a recent National Academy of Science (NAS) study (3), that the unique requirements for U.S. mining may be limiting the technologies available to coal miners and technology options for mine operators. Accordingly, the study recommended that the National Institute for Occupational Safety and Health (NIOSH) and MSHA re-examine their technology approval and certification processes to ensure they are not deterring innovation, and explore opportunities to cooperate with other international approval organizations to harmonize U.S. and international standards without compromising safety. Lastly, the National Technology Transfer Act (NTTA) and the accompanying Office of Management and Budget’s OMB-119 circular mandate the use of consensus-based standards by federal agencies. However, for U.S. mining operations, MSHA cannot accept such standards unless a determination is made that such standards provide an equivalent level of protection for the miner, per the requirements of the 1977 Mine Act, the 2006 MINER Act, and 30 CFR Part 18 regulations."

Jan 1, 2017

By T. B. Thompson

The Leadville District has been a prominent metal producer since its discovery in 1860. Veins and replacement bodies both have contributed to district production. The latter have been the major metal sources and are hosted within the Paleozoic Leadville, Dyer, and Manitou Dolomites. Igneous bodies representing eight separate events cut the sedimentary section. The main intrusive complex within the district occurs in the Breece Hill area and was the thermal center about which the vein and replacement ores exhibit mineralogical zoning. Precious metal-pyrite-quartz veins (quartz Th= 422 to 469°C; salinity < 4.2 wt. percent eNaCI) occur within or peripheral to the Breece Hill Intrusive Complex, whereas base metal veins and replacement bodies extend from the complex margins outward as much as 2 mi. Pre-ore and post-ore igneous bodies occur, but Fragmental Porphyry dikes immediately post-date the ore event. The Fragmental Porphyry grades downward from a heterolithic breccia with rock-flour matrix to one with a dark, glassy, sulfide- and phenocryst-bearing matrix, commonly with quartz-feldspar porphyry selvages on the dike. Two types of replacement bodies are recognized in the district: 1) the Leadville-type (LTM), massive sulfide (> 60% sulfides) bodies with recoverable Zn, Pb, Ag, and Au, and 2) the Sherman-type (STM), sulfide bodies (low total sulfide) with barite, galena, sphalerite, argentian tetra.hedrite, and minor pyrite. The latter type occurs only within the Leadville Dolomite and is found throughout the Mosquito Range and extending into the Alma District. The Leadville-type replacement bodies are zoned with a pyritic margin and base metal core. Wallrock alteration and trace Pb-Zn dispersion are strongly developed in igneous wallrocks but are weakly developed in carbonate wallrocks. Cu:Zn, Ag:Zn, and Au:Fe ratios increase outward from the center to the margins of LTM. Some of the sulfide bodies are localized on earlier-formed magnetite skarns. Pyrrhotite, pyrite, and marcasite are the earliest formed sulfide phases while chalcopyrite, marmatite, and galena developed later. Tetrahedrite and electrum occur in vugs and fine veinlets cutting the sulfides. Late-stage barite, dolomite, and fluorite occur as minor phases. Pressure-corrected Th for quartz (375-410°C), sphalerite (374-387°C), barite (320-360°C), and dolomite (310-314°C) fluid inclusions with salinities < 5.2 wt. percent eNaCI characterize the fluid responsible for the formation of the Leadville-type orebodies. These values clearly demonstrate the high temperature and low salinity of the ore fluids. Sulfur isotope analyses for galena and barite from LTM are - 1.9 to + 0.9%o and 7.8%o, respectively. Proximity to feeder veins and favorable dolomite hosts are the principal controls on ore localization. The Sherman-type bodies are not internally zoned but commonly have host rock silicification near the orebody margin or in the footwall rocks adjacent to fluid flowpaths along faults. Early quartz, pyrite, dolomite, and white barite precede base metal-silver minerals which are followed by late quartz and golden barite. It is not clear whether the early quartz and the late quartz and barite are part of the STM-forming process. Fluid inclusion analyses yield trapping temperatures as follows: early quartz, 316-341 °C; barite, 264-347°C; low-iron sphalerite, 215-265°C; and late quartz, 260-278°C. All inclusion fluids have salinities < 8.1 wt. percent eNaCI. Sulfur isotope values for barite and galena from STM range from 13.2 to 24.00/00 (avg: 18.4%o) and -6.8 to -3.8%o (avg: -5.5o/00), respectively. A hydrothermal fluid d34SSS of about 15%o is needed in order for galena and barite in equilibrium to exhibit the observed sulfur isotope compositions. Equilibrium sulfur isotope fractionation between barite and galena indicates a 300°C temperature of deposition. Two separate hydrothermal events appear to have taken place to form the distinctive Leadville-type orebodies and those of the Sherman-type assemblage. The STM is known to be older than the LTM. The latter is likely mid-Tertiary in age, post-dating emplacement of the Johnson Gulch Porphyry. LTM is clearly related to meteoric leaching of sulfur and lead (and other metals) from the upper portions of the Breece Hill Stock. Fluids were transmitted along faults, bedding planes, and contacts, and cooled away from the intrusive complex. Early ore fluids were weakly acidic and developed argillic assemblages in the igneous rocks adjacent to the fluid conduits. Reaction/replacement of carbonate rocks occurred where fluids encountered dolomite, but rapid neutralization prevented any wide-spread alteration beyond the ore-carbonate host contact. Pressures based on sphalerite geobarometry and stratigraphic reconstruction were 1.0-1.2 Kb. The high temperatures of vein and replacement ore fluids indicate that chloride complexing was more effective in metal transport than bisulfide complexes. Cooling, dilution of ore fluids, and reaction with carbonate rocks were the major factors in LTM ore deposition. STM formed over wide expanses of the Leadville Dolomite terrain adjacent to (and possibly capping) the Sawatch uplift. Sedimentary sulfur was derived from Pennsylvanian evaporite-bearing sequences adjacent to the uplift. Ore leads are strongly radiogenic (J-type) and are compatible with a crustal-leaching model. Temperatures of ore formation are higher, and ore-fluid salinities are lower than Mississippi Valley-type ore fluids. Superimposed upon dark-gray, diagenetic Leadville Dolomite are several stages of hydrothermal dolomite regionally distributed astride intrusive centers of the Colorado Mineral Belt. The presence of these later dolomites argues for dolomitization and later ore deposition in response to an abnormal thermal gradient caused by emplacement of Laramide batholiths and their generation of convective flow of meteoric fluids.

Jan 1, 2013

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By Greg Beckstrom

On Oct. 1-3, SME?s Twin Cities chapter (SME TC), in cooperation with the University of Minnesota ? Duluth?s Precambrian Research Center (UMD-PRC), cohosted a symposium on silica sand mining and processing. The conference was held at the Earle Brown Heritage Center near Minneapolis. The symposium was followed by a day-long field trip to operating mines, processing plants and loading facilities located in southwestern Wisconsin. Speakers and attendees at the symposium included university professors, industry experts, regulators, mining company representatives, equipment suppliers, consulting engineers and service companies. Approximately 320 people attended the conference. In addition, about 50 people who oppose mine development and the oil and gas industry showed up to voice their displeasure with the event and those companies that operate in this space.

Jan 1, 2012

By G. Bulut, Ü. Yenial

"The use of recycled water in flotation has significant effects on flotation and selectivity because the recycled water contains many dissolved compounds and ions that alter the chemistry of the system. In this study, the effects of calcium, magnesium and sulfate, which are abundant components in recycled water, were investigated on galena, sphalerite and pyrite flotation using pure minerals and a complex sulfide ore by conducting bench-scale flotation, microflotation and zeta potential measurements. The bench-scale flotation tests indicated that higher recoveries of galena and sphalerite are obtained when water is recycled, due to higher concentrations of ions in recycled water. However, there was a critical ion concentration for galena recovery. The microflotation tests showed that galena recoveries at different pHs in recycled water are lower than in tap and distilled water. Pure sphalerite recoveries improved in recycled water in the bench-scale test with ore. Pure pyrite was depressed with recycled water as well. Zeta potentials became less negative with increased calcium and magnesium ion concentrations due to their adsorptions, and the presence of sulfate ions was seen to increase the negative charges of sphalerite and pyrite, conversely for galena. IntroductionWater is among the most important elements for mining and mineral processing. The distance to water sources is one of the major factors for mine site selection. The mining and mineral processing sector needs and consumes large quantities of water. In Chile in 2014, the copper mining sector alone consumed 12.7 m3/s fresh water for 1.189 tons of ore processing, and recycled 74 percent of the consumed water (Chilean Copper Commission, 2015). A plant that does not reuse or recycle any water will require 1.9 to 3.0 m3 of water per ton of ore processed (Gunson et al., 2012). Many stages of mineral processing, such as grinding, gravity concentration, dense medium separation, wet magnetic separation, flotation and hydrometallurgical operations, use large volumes of water (Schumann, Levay and Ametov, 2009).In mineral processing plants, the process water is recycled from the tailings dams, thickener overflows, and dewatering and filtration units. Wet concentration processes can require large quantities of water. Flotation, the most common process, typically takes place at 25 to 35 percent solids by mass. Most flotation plants practice at least some water reuse and recycled. Modern mines and mineral processing operations generally aim for zero water release (Levay, Smart and Skinner, 2001). In most cases, water quality has been found to affect flotation performance, and this interaction remains under investigation."

Jan 1, 2016

By A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, Y. Xiong, J. Gu

"As ores degrade, mining techniques and chemistries change to meet market demand and maintain product quality. The balance of recovery and grade is a significant challenge in the Crago Process where an anionic collector is used to float phosphate, followed by acid scrubbing, then an amine float to improve product grade. As the grade is a requirement for DAP and MAP production, recovery is the criteria to suffer. Phosphate losses in the amine float can bring overall recovery down by as much as 18%, creating a growing need to think outside the box to improve recovery. This paper will focus on the theory of amine tail recycling and the best methods to optimize the overall phosphate recovery by recycling the tails from the cleaner flotation step. INTRODUCTION In 2014 the total US phosphate production was down 13% over the prior year, from 31.9 to 27.1 Mt, which accounts for 12.32% of the world’s phosphate rock production. Florida and North Carolina phosphate production accounted for 80% of total US phosphate production, which was down from 85% the previous year. This decline is due in part to the closing of the last phosphate mine in Polk County, FL - which had an operating phosphate mine for over 100 years (Gurr, 2015). Another factor contributing to the reduction in contribution from FL & NC is the increasing challenges in beneficiating the remaining ore deposits. The Central Florida mining district has historically been in the Bone Valley deposit, where raw apatite was abundant with P2O5 values as high as 15%. The Bone Valley ore also had characteristics favorable to beneficiation to 27.5-29.7 %P2O5 while achieving recoveries above 86%. The move southward into the Hawthorne Formation has seen the ore feed grade hit some historic lows, and the matrix characteristics pose more challenges to phosphate producers. The Hawthorne Formation experienced lateritic weathering after the Bone Valley formation which altered the apatite to aluminum phosphate minerals, and alteration of montmorillonite to kaolinite, releasing MgO that caused the dolomitization of the top of the Hawthorne limestone (Cathcart, 1966). Elevated levels of dolomite can yield an increase in slurry viscosities, reduce production rates, and increase energy costs in the wet-acid fertilizer process. The MgO will also act to dilute grade, making it more difficult to achieve a standard 18-46-0 product (McHardy, 1981)."

Jan 1, 2016

By Fred W. Brackebush

In underground stopes that require more than minimal support, backfill is almost universally used. The term cut and fill stopingis used in a broad sense in this section, which describes underground mining methods requiring support. Support in stopes can be classified as local or short-term and general or long-term. Local support for the back of a stope, for example, can be accomplished with rock bolts or timber stulls. General support for the walls of the stope is provided by backfill. Local support provides a safe working place for the stope miners. General support, provided by backfill, preserves the access way to the stope and prevents large scale dilution of ore. Supported methods are a set of cut and fill stoping methods using backfill for general support and various local support methods. his section is subdivided into three chapters: 19.1 Cut and Fill Mining 19.2 Excavation Techniques 19.3 Backfilling Methods

Jan 1, 2008

By Edward C. Dowling

Froth flotation has been used industrially for many years to separate valuable minerals from their associated gangue constituents. Notwithstanding the significance of this process to the mineral industry, many of the engineering tools needed for the evaluation of the flotation process are still in a developmental stage. Traditionally, the evaluation of a flotation test on both the laboratory and industrial scale has been based largely on a rougher recovery value achieved at a sufficiently long time to give a "final" or "equilibrium" recovery value. The assumption of a time equivalency for a given recovery value between various flotation tests or between laboratory tests and industrial operation underlies this method of evaluation. Such an assumption implies that flotation is an "equilibrium engineering process" and that the time-rate recovery of material from the flotation cell is not affected by changes in the flotation system. It has been shown by Bushell (1) and by Klimpel (2) that the assumption of time equivalency between various flotation tests is unjustified. Consequently, better tools are needed for evaluating flotation test results, Because mathematical flotation models which incorporate both a recovery and a rate function can completely describe flotation time-recovery profiles, they can provide an excellent tool to evaluate flotation tests.

Jan 1, 1984

By E. Hasanbas

Vibrating screens and crushers are the workhorses of material sizing. Unfortunately their natural frequency is often in the range of typical supporting structures, thereby making installations prone to vibration problems. Much of the available literature regarding the support of vibrating screens is fairly confusing and outdated. This paper presents the results of utilizing accelerometers and finite element software in the analysis and design of supports for vibrating equipment. It contains data from field studies of vibrating screen and crusher installations, design of new and repair of existing supporting structures, and the correlation between field data and finite element time history analyses. Finally, the paper summarizes a method for analyzing and designing structures subjected to vibratory loads and predicting their behavior.

Feb 23, 2014

By Satyam Tiwari, Sarat Kumar Das

Tailings from mines and industries impose danger to the environment as evidenced by the recent failures of tailing storage dams. The tailings are mostly non-plastic with silt-size particles, but their behavior is largely dependent on the extreme void ratios of the material. Hence, the critical state provides an appropriate perspective in explaining the behavior of these geomaterials. Based on a comprehensive dataset of non-plastic tailings and non-plastic soils, an attempt has been made here to correlate critical state parameters to extreme void ratios and stress parameters. A hybrid algorithm with multi-objective feature selection (MOFS) and extreme learning machine (ELM) was used to establish the correlation and to identify the most influential input parameters. Based on the information from the proposed hybrid algorithm, a comprehensive prediction model is proposed using multi-gene genetic programming (MGGP) algorithm to facilitate quick estimation of critical state parameters. The performance of both models has been assessed using several performance metrics. The results from the study indicate that hybrid MOFS algorithms perform very well in the prediction of critical state line parameters and the identification of influential features. The findings of the study have significant implications for future research on the safe management of tailing storage facilities.

Dec 22, 2023

By d&apos, I. J. Agati

The stockpiling and reclaiming of bulk materials can be a challenging task for engineers seeking the optimum solution for plant needs, reliability, and at lowest unit cost. The objective of this paper will be to expose advantages, disadvantages and limitations of many storage and reclaiming systems to the responsible engineer and management. The paper will emphasize the practical aspect of stockpiling and reclaiming methods. Many valuable and interesting papers are available dealing with the theoretical viewpoint and application of a particular manufacturer&apos;s machine. Several of these are mentioned in the bibliography. As many practical parameters as possible will be given. After twenty years in the field of designing and selling bulk materials handling systems, the needs of the user and the plant are recognized and reasonably understood. This paper cannot give solutions to all problems In this vast field but will stress practical applications and examples of various installations. The evolution of advancements in materials handling is based upon not only technological innovations, but learning from many experiences of others and utilizing them as stepping stones to improved installations.

Jan 1, 1969

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

As a result of the rise in global demand for pure copper, there is urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as an effective and efficient leachant for the dissolution of chalcopyrite. This work reports different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from Wase Local Government Area, Plateau State, Nigeria, and assayed as 11.30 wt% of Cu. At the optimum leaching conditions (0.4 mol/L NH3-( NH4)2SO4 leachant concentration; 75 °C reaction temperature; 45 μm particle size), the extent of chalcopyrite ore dissolution reached 87.4% within 120 min. The dissolution rate was affirmed to conform to the diffusion control mechanism with the activation energy, Ea, of 38.84 kJ/mol and a reaction order of 0.661 for the leachant concentration being established. The leaching mechanism was affirmed by characterizing the raw ore and the leached product by XRD and SEM-EDS analysis. Ascertaining optimal leaching conditions for copper using alkaline leachant is advantageous from the environment and economic points of view.

Jan 6, 2023

By MUSTAFA ERKAYAOGLU, Muhammet Mustafa Kahraman

Particulate matter (PM) is one of the main actors related to air pollution caused by surface mining. Fugitive dust, considered as particulate matter that cannot be collected by conventional measures, is classified by the particle size. The Environmental Protection Agency (EPA) categorizes PM as coarse and fine particles based on the particle size being less than 10 μm (PM10) and less than 2.5 μm (PM2.5). Basic operations of surface mining such as drilling and blasting, loading, haulage, and processing are processes that can potentially generate fugitive dust. Regulations and legislations enforce the mining industry to use environmental monitoring systems, fugitive dust level measured by PM10 level as part of this. Air quality monitors are positioned at different locations around surface coal mines and track air quality levels during production. This study introduces a data-driven methodology to handle air quality issues related to fugitive dust at surface coal mines. Data is sourced from different mine equipment in real-time and they are integrated with air quality monitoring systems to provide information to support decisions for fugitive dust. The method is implemented and demonstrated in a case study at a large surface coal mine.

Sep 29, 2020