Search Documents

By Mostafa Benzaazoua, Bruno Bussière, Mukendi Kongolo

The desulphurization process has been proposed over the last few years for acid mine drainage control at certain mines, which generate low to medium grade sulphidic tailings (-3 to +25 wt% S). The environmental sulphur recovery, which means the sulphur to be floated to produce a non-acid generating final tailings, depends mainly on the intrinsic neutralizing potential of the tailings. However, in some cases the sulphur cleaning is complicated by other parameters which affect the flotation probability of the sulphide particles. In this study, a number of tests were conducted with a Hallimond tube and Denver Cell on both pure mineral and mine tailings. To develop a better understanding of the mechanisms of non-selective sulphide flotation, three types of approach were investigated in this work: (i) pure pyrite at progressive milling degrees, (ii) artificial mix of pyrite and quartz at different calibrated granulometry and (iii) same composition tailings with 26 % wt sulphur at progressive milling degrees. The effect of the granulometry on the sulphide flotation was demonstrated both. The results allow us to define a granulometry model, which can then be considered in the whole desulphurization modeling.

Jan 1, 2000

By D. Men, R. Q. Honaker, J. C. Hower

"Maceral separation is one possible technique to expand coking coal resources, either by increasing the blending ratio of non- or slightly caking coal or rationally utilizing the coking coal according to the different behaviors of macerals in coking. The success of maceral enrichment for a given coal using flotation is dependent on the differences in flotation kinetic rate among macerals. This paper presents the flotation rates and zeta potentials of the vitrinite-rich and inertiniterich maceral concentrates obtained from six coal samples of different ranks – from high-volatile B bituminous coal with mean random vitrinite reflectance (Rrandom) of 0.64 percent to low-volatile bituminous coal with Rrandom of 1.73 percent – using a float-sink procedure. The flotation results show that vitrinite-rich concentrates can be produced in tap water using froth flotation only with frother for the high-volatile B and A bituminous coal samples, but there was no good performance for the high-volatile C bituminous and medium- to low-volatile bituminous coal samples. The zeta potential results show that froth flotation could probably separate the high-volatile C bituminous coal samples well by adjusting pH, but there was no good performance for the higher-rank coal samples. IntroductionMetallurgical coke is used in blast furnaces for steel production and is produced by the carbonization of coking coal. Because caking coals are rare and expensive, they are often blended with non- or slightly caking coals. Considering the tight supply-demand situation for coking coal in China, it is important and urgent to develop highly efficient technologies for rationally utilizing and expanding coking coal resources (Mochizuki et al., 2013)."

Jan 1, 2015

By A. D. Hammond

"The drop in iron ore prices has claimed an unwitting casualty in vanadium. Vanadium is dominantly produced as a coproduct of steel production. The recent shutdown at EVRAZ’s Mapochs steel-vanadium operations in South Africa has cut off 10 percent of the world’s vanadium output. In February 2015, Australia’s Atlantic Ltd. suspended operations at its Windimurra iron-vanadium complex after a fire caused severe damage at the plant. Since then, challenging market conditions has resulted in the permanent closure of this operation.This decoupling of vanadium production from integrated iron ore producers presents an opportunity for vanadium exploration companies to target single-product deposits. This trend is manifested in the increasing number of pure-play vanadium ventures around the world.The mine production of vanadium is dominated by three countries — China, South Africa and Russia, which collectively produce 96 percent of the world’s vanadium. While the use of vanadium as an alloy in the steel industry remains the largest application for this metal, growth in demand is expected to come from the renewable energy industry in the form of batteries for energy storage.This article summarizes the current state of vanadium exploration, briefly describes the vanadium market and lists sources of future demand for the metal.Trend in vanadium explorationThe most active participants in the current vanadium exploration are pure-play vanadium ventures in Brazil, South Africa and Australia. These ventures are targeting deposits with higher vanadium grades than those typically mined in titaniferous magnetite operated by integrated steel-vanadium producers.The 10 percent shortfall in vanadium production resulting from the shutdown at EVRAZ’s Mapochs is expected to be partially compensated by Largo Resources’ Maracás Menchen vanadium operation located in the state of Bahia in Brazil. It commenced operation in August 2014 and is expected to produce between 7.6 and 8.6 kt (8,421 and 9,523 st) of V2O5 in 2016 at a target production cost of $3.71/lb (Largo Resources, 2016). This is the first primary vanadium operation to be placed in production in the Western Hemisphere in more than 35 years."

Jul 1, 2016

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012

By Robert W. Row

The run-of-mine coals in the U.S. being fed to coal cleaning plants have become increasingly finer due to the adoption of modern, mechanized mining methods, and economics are dictating that finer fractions, as well as the coarser fractions, be cleaned. Traditional dewatering methods (vacuum disc filters and centrifuges) are proving inadequate for preparing fine refuse for disposal or fine coal product for downstream handling. The Electric Power Research Institute has been supporting research into the nature and limitations of mechanical dewatering, and novel ways of improving it. The efficiency of various silicone-based chemicals at aiding dewatering was investigated, and it was shown that the final moisture content of hydrophilic coals after vacuum Filtration could be reduced by 1 to 5% with up to 40% increase in filtration rate by addition of one of several of these silicones. EPRI also has an on-going program at its Coal Cleaning Test Facility to investigate the performance of the Larox pressure filter in comparison with that of the disc filter and solid bowl centrifuge. While improvements to the dewatering performance currently being obtained in existing operating plants by such means are achieveable, a fundamental study has shown that, regardless of changes in operating conditions, there may be a limit to the lowest cake moisture content attainable by mechanical dewatering of a given sample of coal fines. Determination of this limit for a specific coal would be useful in designing facilities to dry and handle it.

Jan 1, 1984

By A. L. Hauff

As US Coal producers are looking more and more to the international markets, they face the complex job of planning and managing transportation logistics which make effective use of production capabilities, considers the various contract requirements to be fulfilled, Train, Truck and Vessel capacities, port restraints, etc. Pulling all the necessary pieces of information together to allow proper planning throughout the supply chain is often a time consuming, manual but necessary task. This paper will discuss the various constraints, requirements and considerations to supplying coal to a global market.

Jan 1, 2012

By Xiaolong Bi, Shaohua Luo, Longjiao Chang, Shiyuan Cao, Jianan Liu

iliary agent was proposed. The mineralogical transformation and silicon extraction kinetics of laterite nickel ore in alkaline hydrothermal treatment were studied. The effects of reaction temperature (175 ~ 250℃), molar ratios of sodium hydroxide to ore (1.05 ~ 1.2:1), and laterite nickel ore particle size (44 ~ 178 μm) on the extraction ratio of silica were investigated by using the shrinking core model. The results show that the extraction ratio of silica increases with the increase of reaction temperature, sodium hydroxide to ore molar ratio, reaction time, and the decrease of raw ore particle size. The kinetic analysis shows that the separation of silica in laterite ore can be described by internal diffusion model. The apparent activation energy (Ea) of the reaction was 8.87 kJ mol− 1, and the kinetic modeling was established.

Dec 2, 2021

By Roger G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of Project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the Project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, developing geostatistical reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mecha¬nics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1983

By R. W. Kobler

The pelletizing process for low grade iron ores has undergone continual changes since its inception over twenty years ago. These changes have necessitated filtration equipment changes in order to produce a product suitable for balling. With modern techniques it is now possible to produce pellets of 68% Fe from ores containing as low as 26% Fe. Low grade ores require fine grinding to liberate impurities This shift to finer grinds over the years has necessitated major changes in the filtration steps. Techniques are now available for producing suitable product from ores with Blaines as high as 3600 cm2/gram. This has been made possible by the development of high performance filters. Recent developments have reduced maintenance costs and produced higher production reliability. The paper discusses iron concentrate filtration from its beginning to present day design. It will be shown that the dewatering step prior to balling has gone through four generations of filters. Particular emphasis is placed upon hydraulic studies which have allowed today's optimum designs.

Jan 1, 1978

By Alexander N. Winchell

"Location. The copper mines of Michigan are all in the northern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeasterly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as follows by Foster and Whitney :"

Jan 1, 1920

By L. K. Bandyopadhyay, P. K. Mishra, S. K. Chaulya, R. S. Singh, A. Kumar, N. Tripathi, K. Mandal

A comprehensive field study has been carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling has been carried out to envisage dust concentration due to the existing and closed mines in the region. The predicted total PM10 and PM2.5 levels at the selected receptor locations ranged from 86.39 to 194.89 and from 34.82 to 99.55 µg/m³, respectively.

Jan 12, 2022

By B. A. Hillman

Silicon is the second most abundant element on earth, exceeded only by oxygen. Silicon dioxide forms a crystalline structure of repeating SiO2 molecules which form characteristically hard, durable crystals. As a result, crystalline silica is Ubiquitous in the crustal rocks, sediments and the mineral products derived from mining. An examination of the history of studies that identify silica as a human and animal carcinogen is presented in the context of the development of a public health policy in California. The implications for the cost of conducting aggregate and other mining operations in the state are discussed.

Jan 1, 1992

By Angelina Anani, Nilufer K. B. Akbulut, Sefiu O. Adewuyi

Crucial information about safety, design and operation from ground movement data can be utilized in underground mines. Communicating the information and exploring new findings can be a challenge, however, in a decade where there is an ever-increasing volume and velocity of data due to advancements in mining technologies. This challenge escalates for geotechnical data as they are multidimensional, depending on the space and the rate at which they take place. To tackle this challenge, geotechnical engineers should focus on using simple yet compelling visualization of rock mass data in 3D. Competent visualizations of ground conditions as a trigger action and response plan (TARP) could ease the communication of safety concerns and the exploration of rock mass displacement and strain surrounding an opening at an underground mine. Therefore, this study focuses on using scientific visualization methods by rendering geotechnical data over the surface of a 3D mesh model to display TARP levels. The study was conducted at the East Decline of the San Xavier (SX) Underground Mine, a laboratory mine operated by the University of Arizona. The project aims to produce visualizations that optimize the use of geotechnical data in near-real time.

Sep 1, 2025

By M. H. Rauschkolb, J. A. Cremeens

Geotechnical solutions were developed for closure of two historic, remote underground mines in the deserts of southern California. Closure criteria included access closure, minimal site impact, and optimum use of native materials. The closure designs and construction activities incorporated techniques for protecting sensitive biota, particularly bats and desert tortoise. The types of mine openings that were closed include adits, declines, shafts, daylighted stopes, and dugout dwellings. The desert locations permitted implementation of cost-effective closure techniques that relied upon the use of native materials. The strategies and techniques developed for these desert closures are adaptable to other climates.

Jan 1, 2002

You have been involved with research activities in froth flotation and size reduction. What do you think the future holds for these technologies? Froth flotation and size reduction are essential processing steps common to almost all current mineral-processing operations. The most significant recent advances in both of these technologies have been in the increased size of equipment and in some alternative machine designs, such as the column cells and the high-pressure roller mills. I believe that the next major area of improvement in size reduction will be at least partially driven by an improved awareness of controlling the conditions that influence the efficiency of particle breakage. This would include factors such as water-chemistry influences, the influence of fines from classification, chemical grinding additives and better rheology control. In froth flotation, significant changes are currently taking place in the plant use of frothers. Also, there will be an increasing number of new collector chemistries for certain types of flotation, such as with oxide minerals, oxidized mineral recovery in sulfide systems and improved selectivity with certain sulfide mineral systems. You have been active in implementing new engineering technology in industry. What do you think will be the technological future of mineral processing? Being involved in the invention and industrial implementation of new technology has been one of the most positive experiences of my career. I also have had the unique experience of working in the chemical and petroleum industries as well as in mineral processing. In my opinion, the future of mineral processing will be an exciting, wonderful work area in which to be involved. The development of new technology in minerals processing offers a special challenge compared, for example, to that of chemistry or chemical engineering. In successful industrial innovation involving minerals, having a sound theory is not enough. Instead, what is required is a valid blend of a good idea, meaningful laboratory characterization and, most key, the experience necessary to adjust the plant in such a way to incorporate the idea. The complexity of engineering systems that contain solids, liquids and gases, as well as highly variable natural mineral properties, means that nothing new comes easily. In some cases, it has been difficult to explain how processes practiced in industry for decades actually work, in terms of physical and chemical fundamentals. On the other hand, when a new idea is successfully implemented, the economic and professional returns can be very rewarding. I know of no more challenging field of engineering than minerals processing. What is your view of the future of the minerals industry in general? The need for minerals, metals and coal will be with us for decades to come. In many aspects, the minerals industry became global much earlier than some of the other industrial sectors that are currently experiencing globalization. I believe that fair international competition is beneficial to the users of minerals, metals and coals and to those involved in producing such materials. The key word here for a global economy to work is "fair." So the various playing fields involved such as finance, profit return, regulation and labor should be relatively level for all the players involved. Competition is an amazing driving force for innovation. This has been true in the minerals industry during the last few decades. The mining industry is producing more at less cost per unit than ever before in our history. I anticipate that this trend will continue as long as the global political situation remains relatively stable.

Jan 1, 1997

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By Robin J. Hickson

El Abra is one of the world’s premier copper de-posits. The project is located in northern Chile, 140 km (87 miles) inland from the Pacific coast. It has the same geologic age and structural setting as the world-class Chuquicamata copper mine located 42 km (26 miles) to the south. The current development plan for El Abra extracts798 Mt (879 million st) of high-quality oxide ore. This will require building a solvent extraction/electrowinning(SX/EW) facility that can produce 225 kt/a (248,000stpy) of cathode copper. This will make El Abra the largest SX/EW copper operation in the world, and the world’s seventh-largest copper producer.

Jan 1, 1996

By R. O. Ifill

Alternating current electrocoagulation (AC/EC) may be an alternative to chemical coagulation in the thickening of tailings in the mineral, coal and petroleum industries. In the current study, ground silica (d50 as received, 20 µm) served as the model tailings solid with characteristically poor settling behavior. Its natural initial settling rate was 1.6 x 10-3 cm/min. This paper discusses the indirect application of AC/EC via aluminum electrodes to the enhancement of the settling behavior of the silica. ?Indirect AC/EC? means that the silica was coagulated upon dispersion in water that had been treated by AC/EC. The effect of AC/EC retention time on settling behavior is examined and the water chemistry is analyzed. Test results show that the initial settling rate of silica was enhanced by a factor of 4,000 at its maximum of 6.4 cm/min, under the conditions employed. Settling enhancement was achieved upon contact between the AC/EC-treated water and the silica, and the enhanced initial settling rate was dictated by the floc size. The aluminum dosage increased with AC/EC retention time, reaching a maximum concentration that was equivalent to 13.1% of that predicted by Faraday?s law. Complex aluminum ions are considered to have adsorbed onto the silica surface and an adsorption mass ratio of 0.3 mg Al/g silica was the most effective in enhancing settling behavior. Owing to pH change or slow kinetics, aluminum hydroxide precipitation did not lower the ion product ([Al3+][OH-]3) below the KSP of 6.3 x 10-32.

Jan 1, 2011

By Sean Cassady, Jason Liu, Sanja Zlatanic, Taehyun Moon, Chris Devery

"For the Hollywood International Airport Runway Expansion Project at Fort Lauderdale, Florida, the structural fire durability analysis was completed for a series of tunnels formed by roadway and railroad cells located under the runway structure. A systematic design approach was developed to mitigate structural damage during a fire event and arrive at a practical method to structural fire engineering that is compliant to NFPA 502. To ensure the NFPA 502 requirements are satisfied, the performance based approach was implemented and the engineering analyses were performed for the adopted design fire event. The analyses considered the facility’s unique features including its fire safety systems to determine applicable design fire curves for structural durability analyses. The paper also outlines the process of defining the project specific fire curves for a specific design fire scenario and summarizes the results of heat transfer and structural fire durability analyses. This approach was aimed to assist the owner and Authority Having Jurisdiction to achieve practical decisions to the tunnel facility fireproofing.INTRODUCTIONFort Lauderdale–Hollywood International Airport (FLL) in Broward County, Florida is a major hub facility serving more than 23 million passengers annually. As part of the Airport Expansion Program, the South Runway (9R-27L) Expansion project aimed to meet ever increasing service demands via an increase to runway lengths. This necessitated the placement of one of the reconstructed runways on bridge structures over the existing U.S. Route 1 (US 1), a major north–south U.S. Highway that serves the East Coast of the United States, and the Florida East Coast (FEC) Railway, thus effectively creating multiple tunnel cells beneath the subject runway. For this project, HNTB suggested a tunnel fire damage mitigation system that would protect the runway major structural elements from the design fire event that may happen within the tunnel cells. This paper addresses the issues related to the fire event originating within the tunnel encompassing the US1 highway only, and deals with requirements of NFPA 502 [5] exclusively. Therefore, while approaching the structural fire protection issues for the specific tunnel cells beneath the runway structure, the requirements of the American National Standard NFPA 502 (Standard for Road Tunnels, Bridges, and Other Limited Access Highways, 2008 edition) were followed. Per this standard, regardless of tunnel length, all primary structural concrete and steel elements shall be protected in order to:"

Jan 1, 2016

By Nick Karl, David Wilburn

"The mission of the U.S. Geological Survey (USGS) National Minerals Information Center (NMIC) is to collect, analyze and disseminate information on the domestic and international supply of and demand for minerals and mineral materials essential to the U.S. economy and national security. Understanding mineral exploration activities and trends assists government policy makers, minerals industry decision makers and research entities in identifying where future sources of mineral supply are likely to be discovered, the amount and type of these resources and factors that may affect exploration and development.This review summarizes significant exploration trends related to active sites and budgets, mineral commodities and regional factors for the years 2001-2015. Data were compiled by specialists in the USGS-NMIC, and reported annually in the USGS-NMIC Minerals Yearbook series and in the May issue of Mining Engineering magazine. External data for these analyses were derived from industry sources, published literature, and SNL Metals & Mining, an offering of S&P Global Market Intelligence (New York, NY).The USGS-NMIC compiled exploration site data for more than 80 mineral commodities, focusing on base metals, diamond and precious metals. More than $138 billion constant U.S. dollars were budgeted by the minerals industry from 2001 through 2015 to explore more than 16,000 mineral deposits globally (SNL Metals & Mining, 2016a). Annual analyses identified where mineral exploration took place by principal commodity target, ranked the magnitude of activity in each region, identified the factors that most affected changes in exploration activity and highlighted developments that led to changes in global supply or increased diversity of supply to the United States. Geographic classifications noted in this report were Africa, Australia, Canada, China, Latin America, Pacific, Russia, United States and Rest of the World."

Apr 1, 2017