Search Documents

By Jiayao Wang, Jian Chen, Leiting Shen, Hongyang Wang, Zeping Cao, Ziru Wang

Large amounts of by-products, including coal gangue, circulating fluidized bed (CFB) slag, and coal fly ash (CFA), are generated during mining, washing and burning of high alumina coal (HAC). The stockpile of these by-products of HAC will cause the pollution of air, water and soil. Meanwhile, the unbalanced regional distribution of bauxite and alumina production has been a critical challenge for the sustainability of world alumina refineries, especially for China. Therefore, economical extraction of alumina from by-products of HAC not only resolves the environmental pollution problems caused by stockpile but also decreases the dependence degree of import bauxite in China. Considering the fact that powder alumina can only be produced by alkali methods, the alkali extraction of alumina from by-products of HAC is summarized in this paper. Based on the formation process of by-products of HAC, the principle, research status, and problem of existing methods were analyzed and discussed, as well as the forecast of research trend. The analyses indicate that simplex recovery of alumina from byproducts of HAC generates large amounts of leaching residue (red mud) with difficulty for disposing, while comprehensive extraction of alumina and silica meets the research trend for clean and high-value utilization.

Aug 25, 2023

By M. Adnan Göksel

Pyrite cinder is generated by roasting pyrite for sulfur dioxide production. It contains up to 62% iron, but also may contain other hazardous or toxic materials such as Zn, Pb, As, T1, Cd, Cu, Sn and S. Furthermore, the physical characteristics are not properly suited for conventional sintering. As a result pyrite cinder is considered to be unsuitable for iron and steelmaking or for outside storage because of its potential for causing environmental problems. In recent years industrialized nations have put increasing pressure on the manufacturers to either use such waste products or properly dispose of them. In this study, solutions to both the iron recovery and disposal problem were attempted by pelletizing the pyrite fines with internal carbon. The pellets, after hydrothermal hardening, were reduced and melted in a furnace for hot metal production. Hot metal of usuable quality was produced and the hazardous materials were either collected with the fumes or in the slag.

Jan 1, 1984

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

Historically, as for most reagents used in flotation, the wide-spread use of dialkyl dithiophosphinates as collectors in practical applications has preceded a detailed scientific understanding of how they work. Dialkyl dithiophosphinates are a technologically and commercially important class of collectors used in the flotation processing of Cu-Au, complex polymetallic, and precious metal ores. Plant usage has demonstrated that dithiophosphinates exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive health, safety, and environmental (HSE) profile. Although dithiophosphinates received little attention in the past in the flotation research community, recently, there has been significant interest in this chemistry, and numerous studies have been conducted to understand the fundamental interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized and explained by drawing on concepts and insights from coordination chemistry. A comparison between the interactions with various minerals and metals of dithiophosphinate and dithiophosphate analogues brings out some of the subtleties that seemingly minor changes in collector chemistry can make. The critical overview and analysis given here is useful in identifying gaps in knowledge regarding this important class of compounds. This in turn can provide a basis for the design of studies to advance our understanding of dithiophosphinate flotation performance.

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020

By Michael E. Zellars

The distribution of phosphate in Pliocene-Miocene deposits of the Southeastern United States was controlled by the prevailing geologic setting. For each basin a unique set of conditions in terms of relationship of land mass to shelf, depositional environment and seawater composition, and movement controlled phosphate distribution. Concentration sufficient to recognize the deposits as a resource occurred in lagoons or shallow neritic zones, with clastics and carbonates diluting the section basinward. Each deposit within a basin displays similar metallurgy and lithology, notwithstanding post-depositional alteration.

Jan 1, 1978

By C. Patrick

Longwall face-to-face equipment transfers or moves are, for many companies, the largest single source of non-productive time in a longwall mining system. Detailed planning and resourceful thinking are paramount for economical, safe, and timely longwall moves. New equipment and innovative techniques are frequently tested in order to reduce overall move time. Determining the cost effectiveness of these ideas is difficult since the decision is influenced by many subjective factors. A project scheduling simulation model of the longwall move process was developed in order to analyze and assess the economic viability of innovative transfer methods and equipment. The model provides a project duration frequency distribution and lists of critically indexed activities and paths. It compares the monetary savings from reduced transfer time and capital costs for several innovative ideas.

Jan 1, 1994

By A. Ramage

Since late 2010, CH2M HILL has been working with a confidential client who holds a long-term commitment to sustainable development (SD). The commitment is aligned with all three elements of the triple bottom line: people and society, ecosystems and environment, and financial and economic systems. These commitments are carried forward by the firm?s executives, managers, and operational sites, and are evident in materials posted on the company?s public website. These materials include a formal sustainability report prepared in accordance with the Global Reporting Initiative (GRI) guidelines (GRI, 2006), a report that outlines key SD challenges and progress toward the GRI targets, and a delineation of risks and opportunities outlined in the firm?s Form 10-K and Annual Report. In keeping with its commitments to SD targets, our client wished to consider SD issues in its decision processes for facility expansion or new projects. The company engaged CH2M HILL to meet this goal, based on working relationships established through existing contracts and CH2M HILL?s leading capabilities in sustainable solutions.

Jan 1, 2012

By Jafar Safarian, Manish Kumar Kar, Ahmad Hassanzadeh, Casper van der Eijk

To minimize the carbon footprint in the industrial valourization of bauxite residue, hydrogen was used as a reducing agent. The current study experimentally investigated hydrogen reduction of bauxite residue-CaO sintered and self-hardened pellets at 1000 °C, along with magnetic separation of these reduced pellets for iron recovery. Calcium was introduced to bauxite residue to form leachable calcium aluminate phases with the existing alumina in bauxite residue. This involved the addition of either CaCO3 or a mixture of CaO and CaCO3 while maintaining the fixed Ca content during pelletization. The former underwent sintering at 1150 °C, while the latter was self-hardened through the cementing effect of CaO in exposure to moisture and air. Both types of pellets were reduced in a thermogravimetry furnace at an elevated temperature under similar conditions. The pellets were characterized by the X-ray diffraction (XRD) method and scanning electron microscope (SEM) coupled with energy dispersive spectroscopy (EDS), and their physical and mechanical properties were measured via standard techniques. During hydrogen reduction, a negligible amount of gehlenite ( Ca2Al2SiO7) was formed in the self-hardened pellets, while this phase dominated in the sintered pellets. Alumina in the bauxite residue converted to mayenite phases during reduction in both the pellet types; however, reduced self-hardened pellets had a higher amount of alumina containing mayenite leachable phase. The two pellets showed similar reduction behaviour, while different chemical, physical, and mechanical properties were observed. The magnetic properties of milled reduced pellets were examined through a Davis Tube magnetic separator in a wet environment under a constant magnetic field of 800 G. Higher iron recovery was observed for the self-hardened reduced (41%) pellets than for the sintered pellets (27%).

Nov 23, 2023

By A. J. Martin, M. J. Peoples, D. J. Adams, A. Opara

"The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium (Se). Nitrogen species are also found in association with coal-mining drainages mainly due to the leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal-mining environments in British Columbia. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains.Treatment to remove Se from coal-mining waste waters has proven to be challenging for conventional water-treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry.This paper's electro-biochemical reactor (EBR) technology provides a controllable and consistent supply of useable electrons to the microbes directly at a low voltage potential (1-3 V) and low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical and robust biotreatment system. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required.Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal-mine waste waters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia’s coal-mining waste waters.IntroductionSelenium in Mining. Selenium (Se) is a naturally occurring trace element, which is an essential nutrient in small amounts (Thompson and Robinson, 1980; Brown and Arthur, 2001). However, it is also toxic to aquatic life, birds, and humans at very low concentrations. A major concern with waterborne Se is the potential for its bioaccumulation in aquatic food chains, resulting in acute and/or chronic toxicity to fish, water birds and amphibians (Besser et al., 1996; Conley et al., 2009)."

Jan 1, 2015

By Robin J. Hickson

El Abra has mining concessions granting the right to exploit minerals in more than 130 km2 (32,122 acres). SCM El Abra owns “rights to occupy” the surface of these claims. The company also owns the surface rights over the process plant area and over land conveyor route. The project has procured all material easements relating to the mine area, processing facilities and access rights of way. Engineering, procurement and construction Figure 1 sets out the development and construction schedule for the project. Development is already well under way. As of early January 1996, about 70% of the project was complete and more than 80% of the capital expenditures were committed.

Jan 1, 1996

By L. R. Stoiser

The mineral resource potential of the Los Bronces deposit was successfully evaluated by an intense, coordinated program over a 37-month period (April 1978-May 1981) as part of an economic feasibility study. The program included more than 120 km of core drilling, 63 km of access road construction under adverse topographic and climatic conditions, detailed geological mapping, plus other related activities. This Tertiary-age copper-molybdenum deposit is composed of an earlier mineralized porphyry-type body intruded in part by a large complex of mineralized hydrothermal breccia pipes. Both intrusive and extrusive igneous rocks are present. Erosion, oxidation, leaching, and supergene enrichment of copper have resulted in a deposit now exposed at the surface that contains more than 368 Mt grading about 1% copper equivalent as sulfides.

Jan 1, 1982

By Joseph J. Yancik

An exchange of coal mine specialists was made with the USSR under an "Agreement on Exchanges and Cooperation in Scientific, Technical, Cultural, and other Fields for 1972-73," which was signed by President Nixon and Chairman Breshnev on April 11, 1972.* This exchange, in the field of coal mine safety and scientific research in hazard control technologies, was one of 16 technical exchanges covered under the above agreement. A six-man USA delegation visited the Soviet Union from September 9 to September 21, 1973. The delegation visited four deep mines, three in the Donets Basin and one in the Moscow Basin, a State Safety Research Institute, a Mine Research Station and associated Research and Design Institute, two Research and Design mining equipment institutes, and a Trade Union-sponsored health sanitarium. In Moscow, the delegation received a briefing on the Soviet coal industry from First Deputy Minister Vladimir Fedanov. A similar briefing was given to us on the Donets coal basin by the Deputy Minister S. Saratikyanz of the Ukrainian Coal Ministry. Lengthy technical discussions were held with the mines staff and research personnel at the institutes we visited. In addition, we had detailed discussions with key staff members of two combinats "Donetskugol" and "Tulaugol." In all these meetings, principal topics were matters of safety related to hazards associated with face mechanization, coal transport, methane gas control measures, gas outbursts, coal and rock outbursts, fire fighting add control, explosion suppression and control measures and other related hazard factors. There was also much discussion on miner training, miner's attitudes toward safety and accident prevention practices, and preparation and enforcement of safety rules and regulations. The delegation was very warmly received and constant attention was given to our needs. Our numerous questions were answered with candor although quite often in not as much detail as we would have liked.

Jan 1, 1974

By A. T. Yu, K. A. Young, Ronald M. Hays, Sanford Terry, D. R. Campbell, J. K. Lovrien, W. L. Price, C. W. Matthews, W. R. van Slyke, S. P. Cole

Storage and transport systems are essential for mineral processing. Section 10 includes systems for storage and transport of dry bulk materials, slurries, and water necessary for operation of mineral pro¬cessing plants. All aspects of these systems are presented, including material characteristics; dry material placement in and reclamation from storage stockpiles and bins; dry material conveyance; hydraulics (liquid flow and pumping); slurry characteristics; slurry storage and reclaim, slurry flow (distributors, launders, and pipes), and pumping; water (primary and secondary process, reclaimed, fire, cooling, and domestic) supply, transport, and storage; equipment selection and sizing; power transmission; controls; and health and safety. The mate¬rials considered include crude ore; process and other water supplies; initial, intermediate; and final in-plant materials; finished materials; and tailings and other waste products. Section 10 is a compilation of practical operating data for engineers, technicians, and plant opera¬tors. For the design of mineral processing plants, including selection and sizing of equipment, the design engineer should consult with equipment manufacturers, suppliers, engineering firms, and plant op¬erators with specialized experience in particular materials handling methods. When unusual conditions are encountered, actual pilot or full scale testing may be required to insure adequate design. Operation of mineral processing plants is dependent on the proper engineering and construction of storage and transport systems for dry bulk materials, slurries, and water. It is obvious that processing plants cannot produce the required quantities of semifinished and finished products unless these material can be transported adequately to, through, within, and from the plant. Costs of storage and transport systems may exceed 50% of the total capital and/or operating costs. Considerable attention must be given to the design, layout, and engineering of these systems. These systems are interrelated with the mineral processing method and it is necessary to determine the best combination of mineral processing method and storage and transport systems. Storage and transport systems perform a major supportive func¬tion to mineral processing. The final selection of these systems depends on the final selection of the processing method and related systems (environmental control, tailings and waste disposal, etc.). The process¬ing method determines the characteristics of materials to be stored and transported; distances, elevations, flow rates for transport; and storage requirements. Flowsheet After selection of the processing method and related systems, a flowsheet must be developed. This flowsheet should indicate produc¬tion rate, percent solids or moisture, and specific gravity for all initial, intermediate, and final products or product flow streams. It also may be necessary to know the size analysis, chemical analysis, abrasiveness, and other physical characteristics of various product flow streams. The flowsheet provides basic information for plant layout, storage requirements, and selection and sizing of process and transport equip¬ment. Storage and transport systems often function improperly be¬ cause of inadequate flowsheet data or process revisions, resulting in improper equipment selection and sizing. Further details on plant design are presented in Section 33. After selection and sizing of process equipment, it is necessary to select the type of material transport equipment to be used for in¬plant materials handling as well as crude ore, tailings, and final prod¬ucts. The storage and/or surge requirements, including capacity and location, then are determined. Storage and/or surge capacity is neces¬sary for leveling production rate fluctuations due to variations in material characteristics; production scheduling; equipment mismatch¬ing, failure, or breakdown; and scheduled maintenance downtime. Variations in ore grindability will cause fluctuations in throughput or production rate for grinding mills and variations in ore grade will cause fluctuations in production rate for concentrating equipment. Variations in material moisture content and percent solids can have serious effects on the capacity of material transport equipment. In some cases, a blending system may be desirable or necessary to reduce variations and to obtain uniform production and/or metallurgy. Storage capacity often is needed because of different production schedules for various phases of the mining and mineral processing complex. As an example, the mine and coarse crushing plant may operate on a one- or two-shift-per-day schedule while the fine crushing plant and concentrator on a three-shift-per-day schedule. This would require storage between the coarse and fine crushing plants. Another example would be load-out storage where unit trains are used to haul concentrate or final products. The concentrator could be operated on a three-shift-per-day schedule while only I to 2 hr may be scheduled for unit train loading. This would require adequate load-out storage so that the concentrator can be operated continuously. Process equipment with mismatched capacities requires storage or surge capacity between the mismatched equipment to achieve oper¬ating efficiency. As an example, the fine crushers may have greater capacity than the rod mills. Storage between the fine crushers and the rod mills permits both the crushers and rod mills to be operated at optimum capacity with the crushers actually operating or running a lesser number of hours per day. Mismatched capacities for process and transport equipment also may require storage or surge capacity. Mismatching of equipment capacities most often occurs because of the difficulty in equipment sizing. Thus, the design engineer must anticipate where in the flowsheet these mismatching capacities are likely to occur while making every effort to assure that equipment is selected and sized properly. Equipment breakdown can cause major operating difficulties and lost production. These breakdowns can be reduced with adequate scheduled maintenance. Lost production due to nonscheduled down¬time caused by equipment breakdown can be reduced further by standby equipment and storage and/or surge capacity ahead of essen¬tial mechanical and electrical equipment. As an example, standby pumps and conveyors often are available as part of the in-plant trans¬port system. Storage and/or surge bins and tanks often serve dual functions, such as dewatering, mixing, and smoothing production rate fluctuations.

Jan 1, 1985

By A. S. Macfarlane

Over the last few years, and especially the last few months, issues relating to Corporate Governance in industry in general, and the Minerals industry in particular, have become increasingly topical, as a result of a number of scandals and failures. The development of International and National Codes for the reporting of Mineral Resources and Reserves began some years ago, and has been followed by more stringent Listing Rules for the Securities Exchanges, as well as more standardised formats and protocols for financial reporting of assets and activities. More recently, some countries have adopted Codes for the Valuation of Mineral Properties, which have focussed on standardisation of valuation approaches to be adopted, and the qualifications of people deemed competent to sign off such valuations. This process has not been without criticism, the main criticism being the proliferation of local standards and regulations, which are often difficult to apply and regulate, or which are too prescriptive for multinational mining companies to deal with. In South Africa, these concerns have been recognised, while at the same time a need has been identified to establish a Code which could be applied to South Africa, and the African continent as a whole. Such a development would necessitate that the Code satisfies the needs of the continent, but in a global context. This global context has already been set by the activities of the International Organisation of Securities Commissions, the International Valuations Standards Committee and the International Accounting Standards Board. This paper explains the progress and process that has been established in South Africa for this purpose, and highlights the key issues which are open to public debate, so that the process is inclusive and transparent, whilst at the same time it is consistent with international time frames, and provides a deliverable product that meets the desired objectives.

Jan 1, 2004

By Ronald C. W. Webber‑Youngman, Philani Larrance Ngwenyama

Entrapments are a huge risk in underground mines. This happens when miners (or any other persons who have entered underground) survive the initial event of an accident, become trapped or lost in unknown and life-threatening locations after evacuation, and remain unaccounted for. At this point, every second counts, and emergency response is highly desired for any chances of saving survivors. The survival chances of the missing persons depend on how quickly they can be located. Rescue teams are often deployed to search for the missing persons underground. However, the rescue teams are forced to search in random and presumed areas of the mine. This is due to the unavailability of information pertaining to the whereabouts of the missing persons. Not only the provision of accurate locations, but various other types of information such as post-accident two-way communication can enhance the survival chances of the missing persons. This information can be provided by a fit-for-purpose missing person locator system. A wide variety of missing person locator systems are already commercially available, some are in testing phases and others in prototype and development phases. This includes tracking, tracing, location detectors and post-accident two-way communication systems. These systems have unique functionalities, capabilities and limitations; making it difficult for mines to select the most effective, applicable and suitable system specific to their mine. In this study, the user requirements for a fit-for-purpose missing person locator system were developed. The purpose of the user requirements was to provide a guideline to facilitate the system selection process. The user requirements can also be used as a tool to measure and evaluate the performance of the selected missing person locator system. The user requirements were also used to predict the success of the selected system under different missing person incident scenarios. The development of the user requirements showed a potential for many other benefits for missing person locator systems.

Nov 2, 2023

By RICKARD HANSEN

With vehicles frequently found in underground mines and tyres being a major fuel item, the risk of tyre fires will be severe underground. This study presents an in-depth analysis of tyre fires on mining vehicles to increase the knowledge of the risk, applying data from full-scale fire experiments and CFD simulations. It was found that the wheelhouse of the loader caused an increase in the flame tilt angle of approximately 10%, decreasing the flame impingement and heat flux downstream. The flame temperature of the drilling rig tyre was found to be approximately 7% higher than the loader tyre, increasing the risk of igniting adjacent fuel items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for the drilling rig case for higher flow velocities, indicating the influence of a varying wheelhouse/mudguard construction and tyre geometry on the flame tilt angle. The construction of the loader resulted in a flow behaviour, where the short distance to the front mudguard/tyre and the separation of flow directly downstream of the protruding construction led to fire gases being steered past the front mudguard/tyre. In the drilling rig case, the longer distance to the front mudguard/tyre led to fire gases being directed towards the body of the vehicle after passing the area with flow separation. An increased knowledge of the tyre fire risk on mining vehicles and mitigating measures would improve the fire safety in underground mines.

Feb 10, 2022

By Jürgen Kretschmann, Christina Suarez, Jürgen Brune, Stefan Möllerherm

"The Ruhr region in Germany’s North-Rhine Westphalia is going through significant change. By the end of 2018, the last two underground hard coal mines in the Ruhr, Ibbenbüren and Prosper-Haniel collieries, will close their portals and bring an end to more than 200 years of coal mining and an industry that was once the economic and cultural backbone of the area. Ruhr is undergoing an impressive economic and cultural transformation, as it gradually shifts from being a region once dependent on coal and steelmaking to a post-mining region focused on redesigning itself as a cultural center. This article focuses on the socioeconomic impacts of the transformation into post-mining and the roles of the government, labor unions and local community to aid the transformation from the perspective of an American student. It will look into the cultural values that are helping to drive the transformation and compare them to American standards and values in order to determine if a similar approach can be used in the United States and its coal industry. History and backgroundUnderground hard coal mining has had a long history and a significant impact on the culture and economy in Ruhr since the early 19th 20century. The Ruhr region is located in the heart of the German state of North- Rhine Westphalia. Ruhr is bounded by the Rhine River in the west, the Ruhr River in the south and the Lippe River in the north, with the Emscher River running through its center.The Ruhr is home to around 5.1 million people and spans an area of approximately 4,500 km2 (1,730 sq miles). Before the era of industrialization, the Ruhr was a rural, agricultural region. Small-scale coal mining began in the 13th century, with coal being used for heating, cooking and metallurgical processes, including steelmaking. With 19th-century industrialization, coal mining became a significant driver of the region’s economic structure. Steam engines, and soon, electric motors, allowed for the pumping of mine water and for powerful hoists hauling from deep shafts, enabling miners to reach deeper coal seams that were once thought impossible to mine. The Ruhr mining boom began in the 1850s, supported by Prussian economic policies that attracted many workers and their families to the region. The population grew from 400,000 in 1850 to 5.7 million in 1957. The coal and steel industries were key contributors to Germany’s “Wirtschaftswunder” — or “miraculous economic recovery”— in the 1950s. In 1956, the coal industry reached its peak production of around 112 Mt/a (124 million stpy) of coal and employed almost 600,000 miners."

Mar 1, 2019

By J. Noll, J. A. Organiscak, A. B. Cecala

"In recent years, significant strides have been made to optimize the design of filtration and pressurization systems used on enclosed cabs of mobile mining equipment to reduce respirable dust and other contaminants and provide the best air quality to the equipment operators. This synergetic effort has involved original equipment manufacturers building mining equipment, manufacturers of heating, ventilation, and air conditioning systems for mobile equipment, filtration and pressurization system manufacturing companies, as well as the National Institute for Occupational Safety and Health, and other government organizations. Considering all the advances made in this area over the last decade, one aspect that NIOSH still needs to assess is the longevity of optimal cab performance with respect to the quality (filtering efficiency) of the filters used in filtration and pressurization systems. In today’s culture, most health and safety professionals automatically believe that HEPA quality filters need to be used to provide the greatest level of protection to workers. Researchers at the Office of Mine Safety and Health Research for NIOSH hypothesized that HEPA quality filters may not be optimal for the mining industry and speculated that MERV 16 rated filters would be more appropriate in most cases. In order to test this hypothesis, NIOSH performed a two-year study comparing both HEPA and MERV 16 quality filters on two pieces of underground limestone mining equipment, being a roof-bolter and face drill machine. Testing showed at the 95 pct. confidence level that there was no statistical difference between the two efficiency filters on both pieces of mining equipment. Since the MERV 16 rated filters were less restrictive and provided greater cab pressure, and since they did not have to be replaced as often as the HEPA quality filters, researchers concluded the MERV 16 filters were the optimal choice for both pieces of mining equipment in this case study comparative analysis. INTRODUCTION When most health and safety professionals today think about filtration efficiencies and their correlation with protecting workers’ health, the normal assumption is the higher the efficiency of a filter, the greater the protection afforded to the workers. The next logical step is to believe that HEPA filters deliver the greatest protection for workers because they provide the highest filtering efficiency. Obviously high-efficiency intake filters are a necessity for an effective cab filtration and pressurization system on mobile mining equipment, but what is the optimal filter efficiency rating for achieving high levels of cab protection factor performance over the service life of filters? To address this question, the National Institute for Occupational Safety and Health (NIOSH) has performed an in-depth laboratory research study over the years simultaneously with numerous field studies to retrofit used enclosed cabs on mobile mining equipment with newer and more effective filtration and pressurization systems."

Jan 1, 2016

By Madhu G. Ranade

A statistically designed pot grate- kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables, bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate, were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a pl ant trial. The target firing temperature at the Empire Plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets

Jan 1, 1985

By G. E. Agar

In the April issue of Mining Engineering there is a technical note "New size laboratory ball mill for Bond Work Index determination" written by M. Nematollahi which is very confusing. My recollection is that a description of an experimental procedure should be such that someone skilled in the art should be able to reproduce the results. Applying this test to this particular article would according to me cause a failure to be registered. There are apparently three batch laboratory test procedures referred to in the article. One of these is the traditional Bond test with all its limitations such as dry grinding followed by exclusively dry screening, two attributes which fail to simulate conventional industrial grinding. There is a second procedure (NSBM) which the author is advocating as an improvement of the Bond procedure but from the description I doubt that anyone would be able to repeat the procedure. For instance, is the grinding to be done wet or dry, if wet at what pulp density, and how is the screening to be done, wet or dry or a combination?

Jan 1, 1995