Search Documents

By D. B. Spears

The sillimanite group includes the aluminosilicate minerals sillimanite, kyanite and and alusite, all of which have the same chemical composition (Al2SiO5). This discussion also includes the closely related mineral, mullite(about Al6Si3O15), which, although rare in nature, is produced artificially for industrial use. All of the minerals in this group have a low coefficient of thermal expansion and high corrosion resistance. This makes them desirable for refractory applications, especially in the steel and foundry industries. Other uses include electrical insulators, abrasives and household ceramic products. The minerals in the sillimanite group decompose with an irreversible expansion at temperatures between 1,300° C and 1,600° C (2,372° F and 2,912° F). Sillimanite and and alusite have relatively small expansion on decomposition (4 percent to 6 percent) and, therefore, can be used as aggregates in refractory products. Kyanite’s expansion on decomposition is large (18 percent). So it is sometimes used to balance shrinkage of other materials such as clays in refractory mixtures. For applications requiring high-temperature volume stability, mullite is more desirable. As an additive, mullite improves resistance to creep and corrosion, and imparts thermal and electrical insulating properties.

Jan 1, 2005

By Steve Klein

Weak rock is an important consideration in tunnel design and construction due to the difficult ground conditions that are often encountered. Nevertheless, when conditions are favorable high advance rates can be achieved leading to economical tunnel construction. Successful construction of a tunnel in weak rocks depends on correctly anticipating the behavior of these unique materials. The objective of this paper is to provide guidelines that can be used to accurately classify the performance of weak rock in tunnels.

Jan 1, 2001

By Lee Browne

The transformation of Peru’s Tintaya copper project from a state-owned company to a private company is under way and the results have been successful. Since Magma Copper Co. assumed operating management in December 1994, production and costs have improved dramatically. To understand the transformation of Tintaya, the transformation of Magma Copper must also be understood.

Jan 1, 1996

By B. K. Parekh, Z. Chen

INTRODUCTION The need for cleaning and recovery of fine (minus 28 mesh or 0.5 mm) coal fraction has increased in recent years. This results from realizing a substantial recovery of ultraclean coal from the waste stream improving overall Btu (heat) recovery, providing extra revenue for the coal industry. Also the potential of using the clean coal so obtained for making coal-water mixture which could replace oil. An additional benefit of recovery clean coal from the waste stream is reducing environmental concern of burning uncleaned coal and in waste disposal. Deashing of coal by physical beneficiation processes is limited by the degree to which ash components are liberated from coal. Conventional processes have been inefficient in terms of Btu recovery, for ultrafine coal. Chemical cleaning methods, which involves leaching of ash material from coal, have provided ultraclean coal at high Btu recoveries, are more costly than the physical cleaning methods. An advanced physical separation technique that appears to address the need discussed above is selective flocculation. This technique which has been successfully utilized in iron ore beneficiation offers the potential of processing fine and ultrafine coal to produce a clean fuel. OBJECTIVES The main objective of the present study is to investigate applicability of selective flocculation technique for recovery of clean coal product from the waste coal slurry supplied by the Peabody Coal co., from their three different coal preparation plants. It is also the objective of the program to conduct preliminary economic study of the selective flocculation process.

Jan 1, 2002

By H. J. Sutherland

This paper reviews the results of the subsidence research prop ram at Sandia National Laboratories. The manuscript highlights the following: the application of empirical methods (profile functions) to the subsidence above longwall panels in the U.S.; the use of the "rubble model" to describe the behavior of broken strata as it distends when it falls to the Mine floor (or top of the rubble pile) and then is subsequently compacted as it is loaded by overlying elements of strata; and, the application of physical modeling techniques (centrifuge simulations) and numerical techniques to study the failure mechanisms in highly structured stratigraphy. The capabilities of the latter two are illustrated ')y comparing their predictions to the results of a field case that has complicated stratigraphy.

Jan 1, 1982

By Jay Nopola, Christopher Johnson, Matthew Minnick, Erik Hemstad, Erik Walega

Mining data collection, storage, and interpretation methods have progressively changed over time. Data collection, for the most part, has transitioned from handwritten notes and logs based on manual gauge readings to real-time data streaming through instrumentation capable of directly communicating with site-based data historians or cloud storage. Data collection and storage have had to adjust commensurately with the volume of data, leading to more complex database architecture. Geoscience interpretation methods have also changed; however, the first goals of modeling and understandings from first principles remain the same and are typically deeply rooted in historical academic work. Machine learning methods are becoming more common, available, and implemented by industry and practitioners. Despite the wide accessibility of machine learning methods, the population of geoscience subject matter experts in the underlying theory of this analysis type is limited. This form of analysis, therefore, must be conducted carefully and in conjunction with subject matter experts, on both machine learning theory and the field it is being applied to. This paper aims to provide background history on data analytics and machine learning, current methods and practices, and high-level geoscience case study examples, as well as take aways regarding the mining industry, potential pitfalls specific to geosciences, and possible perspectives on the direction of artificial intelligence in the future.

Jun 25, 2023

By J. M. Dean, R. L. Grayson, R. C. Althouse, M. J. Klishis, G. L. Winn

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Feb 24, 1997

By L. Lacerda, C. Rose, E. Zellers

Approximately six hundred air sample measurements were taken at several U.S. underground metal/nonmetal mines in 1998 and 1999. This air sampling effort was organized by the Nevada Mining Association to evaluate mining conditions and to evaluate the Mine Safety and Health Administration’s (MSHA) Proposed Rule on Diesel Particulate Matter Exposure of Underground Metal and Non-metal Miners. MSHA’s proposed air sampling method, NIOSH Method 5040, was tested under controlled conditions and under normal mining conditions. Unfortunately, NvMA sampling results have indicated that carbonaceous rock dust, oil mists and even cigarette smoking create severe sampling interference problems for NIOSH 5040.The main conclusion was that NIOSH 5040 did not distinguish between DPM and other airborne carbon particulate. Thus, it is not a reliable method of accurately and unequivocally measuring DPM in underground metal/nonmetal mines.

Jan 1, 2000

By Neil A. Brown

The trona deposits near Green River, in southwestern Wyoming are world class in size and quality. They contain more than 25 times the reserves of the next largest trona deposit at Lake Magadi in Kenya. Based on present rates of production, the Green River reserve should last for more than 500 years. Since their discovery in 1938, the Union Pacific Corp. has been instrumental in the promotion, development and production of soda ash in Wyoming. Union Pacific spent several years drilling the deposits and trying to promote them to chemical companies. In 1947, Westvaco and Union Pacific entered into what became the first trona lease agreement. Today, the Green River Basin leads the world in soda ash production, accounting for about 25% of the world's supply. Green River producers process more than 14.5 Mt/a (16 million stpy) of trona to produce more than 8 Mt/a (9 million stpy) of soda ash. The future for Green River soda ash looks good, with more of the world looking towards the cheaper and higher quality source of soda ash coming from the natural deposits. Production from the Green River deposits should continue to grow as trade barriers and tariffs begin to fall in Europe and energy and environmental costs force the synthetic producers to exit the market.

Jan 1, 1995

By William W. Edgerton, Calvin Locke

INTRODUCTION King County, Washington operates a regions wastewater treatment system that provides treatment to 18 cities and 16 sewer districts in the greater Seattle metropolitan area. The system serves 1.4 million people and currently includes two regional treatment plants. In 1999, a long-range planning study identified the need for a third regional treatment plant, now known as Brightwater. Prior to this project, the county has almost exclusively used the traditional design-bid-build delivery process for its capital projects. However, with the adoption of the RWSP, the county began to study the potential application of innovative project delivery methods. This paper looks at the project delivery methods used for the Brightwater project, based on the specific needs of this large, complex, and multi-faceted project. THE KING COUNTY WASTEWATER TREATMENT SYSTEM In 1958, voters approved the formation of a regional agency called the Municipality of Metropolitan Seattle, or Metro, to build and operate a regional wastewater collection and treatment system. Prior to the formation of Metro, there were no regional wastewater treatment facilities and pollution of Lake Washington and Puget Sound from untreated sewage was a concern for many residents. In 1994, King County merged with Metro. The county’s 1,087 square kilometer (420 square miles) wastewater service area covers most of urban King County and extends into portions of two neighboring counties. The system includes two regional treatment plants, a local plant, 61 pump and regulator stations, and 571 kilometers (355 miles) of conveyance pipeline which convey wastewater from local districts to the treatment plants. As with other areas, the greater Seattle/King County region has seen rapid population growth. The RWSP estimates that the current system would soon reach capacity, and called for the construction of a new third regional treatment plant, called Brightwater, to be operational by 2010.

Jan 1, 2005

By E. Stiakakis

The paper presents a geotechnical simulation of the "Mavropigi" open pit mine (Western Macedonia Lignite Center, Greece), using the finite element method. The simulation was based on the initial planning of the pit using Mohr-Coulomb and Soil Hardening models. Results indicate high stability factors as well as the magnitude of the expected horizontal displacements and floor heaving. However, these deformations do not influence decisively the overall stability unless locally adverse tectonics are encountered. Results can be used in the ongoing update of mine planning and stability evaluation.

Jan 1, 2006

By T. S. Golosinski

Introduction Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost. Both work in very difficult conditions and wear out rapidly. As a result, frequent rope changes are required resulting in substantial cost and productive time loss. Although performance of rigging has a profound impact on dragline efficiency, there are no common, industry accepted standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The performance of drag and hoist ropes depends on: •rope construction that should closely match requirements of the specific application, rope operating conditions and its maintenance and • correct definition and application of the rope discard criteria so that full advantage of the rope can be taken without endangering safety of its operation. This paper reviews the present practice related to all these factors. Its findings are based on the wide survey of the present industrial practice. Field survey In total, 33 North American dragline applications were surveyed of which 17 were Bucyrus-Erie machines, 10 were Marion and six were Page (now P&H). Most of the draglines were stripping overburden in coal mines, but the survey also included some unique applications such as phosphate mining in Florida and oil sand mining in Alberta. Hoist drive power of the surveyed machines varied from 300 to 7775 kW (400 to 10,400 hp). Drag drives varied from 300 to 5815 kW (400 to 7800 hp). Boom lengths varied from 37 to 110 m (120 to 360 ft). Bucket sizes varied from 5 to 96 m3 (6 to 115 cu yd). The hoist and drag ropes installed on the surveyed machines were supplied by 10 rope manufacturers and differed widely in type and construction. Most common rope strand constructions included standard strands, Seale, Warrington, Warrington-Seale and Filler-Seale. Results of the survey [ ] Working conditions Working conditions of hoist and drag ropes are quite different. The first cope primarily with bending on rope drums, point sheaves and deflection sheaves, and with tension force imposed by the bucket and its load. The drag ropes are exposed to severe abrasion at the pit crest, and to severe bending and crushing at fairleads, all while coping with tension forces imposed by resistance of the bucket to dragging. Bending of drag ropes at house rollers and at rope drums is of minor importance for their performance. Differences in working conditions result in different wear patterns, which make it feasible to install discarded hoist ropes to further serve as drag ropes. The hoist ropes wear primarily due to fatigue breaks of wires, while the drag ropes are subject to severe abrasion of outside wires, rope deformation and internal wire-strand breaking. The last is often indicated by the reduction of rope diameter. The summary of working conditions for the surveyed draglines is shown in Table 1. For simplicity, Table 1 does not include the data on rope bending at the fairleads, nor at the deflection rollers and house rollers. Similarly, Table 1 does not include the data on drag rope bending (other than that on the rope drum), as its influence on rope life is insignificant in view of severe abrasion and internal wear taking place elsewhere. The following abbreviations are used in Table 1: [D - diameter of rope drum. DP - diameter of boom point sheaves. d - rope diameter x - mean value of the measured parameter. s - standard deviation of x B/d - average bending ratio of ropes B/d =(D+ DP)/2d n - operational safety factor of the rope (rope stength) x (number of ropes) n(bucket load + bucket weight)] In terms of D/d ratio, the working conditions of hoist and drag ropes are similar to that in other related industrial applications. However, the safety factors of the dragline ropes are lower, which requires them to carry relatively large tension forces. The last explains the fact that the life of dragline ropes is low when compared to other industrial rope

Jan 1, 1995

By J. A. Lombardi

Acid-Minesite-Solutions (AMS) are defined as copper-containing pit lake, tailing pond, acid-mine-drainage, and heap and waste dump irrigation solutions. All of these solutions are characterized by copper, acid and water contents that have value as individual commodities. HW Process Technologies, Inc. (HWPT) has developed nano- and hyper-filtration membrane methods for the separation of copper and other base metals, acid and water from AMS. These treatments are collectively called HWPT?s Engineered Membrane Separation® (EMS®) systems. The EMS® method of copper recovery produces small volumes of higher-concentration copper solution from large-volume, copper-dilute AMS. A case study of the 4,000 gpm Cananea EMS®-AMS plant for the recovery of copper from an acid-pit-lake resource is described. The EMS® method of copper removal from AMD and tails pond waters has been bench-scale demonstrated and are described, complete with projected budgetary capital and operating costs. Additional treatments for the recovery of sulfuric acid and high-quality water from the permeate (membrane passing) waters for the above-described AMS treatments are presented, with budgetary capital and operating cost estimates. [ ]

Jan 1, 2009

By Michael E. Stickney

"Soft technology" computers and computer programs-brings to mind a room full of machines, tape drives, disks, plotters, and printers spitting out financial reports. Computers now have a much broader scope of applications because of reductions in equipment size and cost. For example, people now interact directly with computers to control events. Such computers and associated equipment-called interactive control systems-are often small, relatively inexpensive, and can be designed to increase productivity at mining operations. This is accomplished by improving communications between individuals; giving employees the information needed to make decisions in real time, as events are happening; and giving individuals the background needed to perform more effectively. This paper will describe a procedure for determining the return on investment for interactive control systems, and describe four such systems. The analysis process is general in nature and can be applied to any type of mining operation or production process.

Jan 4, 1981

By Ian McFeat-Smith

Despite a present, short-term economic recession, a remarkable enthusiasm exists in Hong Kong for building infrastructure including major tunnel projects. This paper provides details of current and recent bored tunnel works together with an insight into the impressive list of future underground projects planned by the MTRC,KCRC, Highways Department and Drainage Services Department for the next decade. Risks for each of these works including pipejacking, mixed face and rock tunnelling generally in Hong Kong are also identified. From this is evident that the scale and difficulty of such works continues to increase, requiring the use of more sophisticated methods of construction, the need for better methods of assessing and managing risks and for Government to utilize improved, more equitable Conditions of Contract for such major tunnelling projects.

Jan 1, 2001

By Tim O’Neil

ISO 9000 is a system of quality standards that originated in Europe in the 1980s and has since been widely adopted by manufacturing companies throughout the world. The ISO 9000 standards have received less attention in the minerals industry. But, in part as a result of customer pressure, a trend is beginning to emerge for minerals producers to seek ISO certification. This is especially true among producers of industrial minerals. In early October 1994, SME's Industrial Minerals Division held a conference "ISO 9000 - uniting industrial mineral producers and consumers into quality partnerships," in Nashville, TN to bring people from the industry together to talk about their experiences with ISO 9000. William J. Miles, of Bentonite Corp. Inc., and A. Frank Alsobrook, of Alsobrook and Co., were cochairmen of the meeting. In his introductory remarks, Miles noted, "ISO 9000 is more than a quality program. It is a quality philosophy. Appropriately imple-mented, it is a contract between the supplier and the customer. It leads to continuous quality improvement and reduced manufacturing costs."

Jan 1, 1995

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are kaolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

By J. F. Stenebråten, W. P. Johnson, D. R. Brosnahan

Carbonaceous material (CM) from ores of varying preg-robbing activity from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was characterized in terms of its functional group content, hydrocarbon content, elemental composition, and humic acid content. FT-IR analyses showed neither the presence of hydrocarbons nor of carboxylic, phenolic, or sulfhydrol functionalities. FT-IR bands present included C=C stretching in aromatic rings and C-O-C stretching, indicating presence of oxygen as ether linkages in the carbon matrix. Calculated atomic oxygen to carbon (O/C) ratios did not reveal a trend between maturity of CM and preg-robbing behavior, possibly due to low resolution of electron microprobe analysis. However, the atomic O/C ratios agree with other chemical analysis, indicating that the organic carbon is very mature, similar to or higher in grade than anthracite coal.

Jan 1, 1999

By John McDonald, Peter C. Raleigh, Christopher Dishlip

This paper will discuss how the construction management team and the contractor working together on the City of Los Angeles, North East Interceptor Sewer project, managed information on a daily basis. Data was synthesized from various sources including: inspection, survey, instrumentation, laboratory and the tunnel boring machine data logger systems to produce state-of-the-art reports and graphics which will become industry standard. Special emphasis is placed on how the data is managed and interpreted in a clear and objective manner, permitting the tunneling processes to be carefully monitored and suggesting appropriate action to be taken by the construction management team and contractor.

Jan 1, 2005

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 160 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey’s canvass of producers.

Jan 1, 2005