Search Documents

By Y. Rajpal

The Hedley and Grant pillar strength formula is widely used within the South African mining industry to calculate pillar strengths in bord and pillar mining layouts, and is currently being used at Bathopele Mine. Bathopele is an operation of Anglo American Platinum near Rustenburg, mining the UG2 reef at depths ranging from 40 m to 300 m below surface. The formula includes a parameter K, which is a downrated uniaxial compressive strength value of the rock, used to calculate the strength of a pillar. At Bathopele Mine, for the shallower areas Less than 150 m the value was 33 MPa, but this was increased to 44 MPa due to the fact that rock mass conditions improved and there were no incidence of failure in the shallower areas. Underground observations showed pillars to be stable with no signs of failure, and it was questioned whether the design was not still too conservative, resulting in sub-optimal extraction ratios and consequently a loss of revenue to the mine. A trial mining section was started at the mine where the pillars were reduced from 6 m x 6 m to 5 m x 5 m and the pillar behaviour was monitored for the onset of failure. Numerical modelling was conducted using the TEXAN code to back-analyse pillar stresses in order to find a more realistic value for K. Results from the trial section indicated that the pillar design was in fact too conservative, and the value for K was adjusted to 54 MPa for future designs. This paper details the findings from underground monitoring and numerical modelling results, and includes details for further calibration of the K value in order to further optimize the extraction of the orebody.

Jan 1, 2012

By H. Han, Z. Gao, Y. Gao, W. Sun, J. Wang

Strategic Ca-bearing minerals like scheelite and fluorite are usually separated by flotation, yet the separation is quite difficult due to their similar surface Ca active sites. Compared with the conventional strong collector sodium oleate (NaOL), lead nitrate-benzohydroxamic acid (Pb-BHA), complex collector shows a better selectivity for scheelite, yet its high cost hinders its wide application. Therefore, a novel collector (Pb-BHA-NaOL complex) was initially developed in this work to overcome the abovementioned dilemma. The flotation results of a single mineral showed that Pb-BHA-NaOL had a better selectivity for scheelite than Pb-BHA. Under the conditions of sequential assembly of Pb, BHA and NaOL at the molar ratio of 240:120:1 and pH 9.0, selective separation of scheelite from fluorite could be achieved without adding any depressants. In addition, for the same preferred scheelite recovery, Pb- BHA-NaOL could also save approximately 20% Pb and BHA compared with Pb-BHA. The analyses of the zeta potential measurement and X-ray photoelectron spectroscopy indicated that Pb-BHA-NaOL showed stronger adsorption on scheelite relative to fluorite. Meanwhile, Pb-BHA-NaOL showed more adsorption modes and higher utilisation of Pb and BHA on scheelite than Pb-BHA, which was due to the accelerator, NaOL. Keywords: Scheelite, fluorite, lead nitrate, benzohydroxamic acid, sodium oleate, flotation

Jan 1, 2020

By O. S. Tinkler, K. C. Sole

Approximately 20% of current world copper cathode output is produced using a hydrometallurgical process route, generally referred to as the leach–solvent extraction–electrowinning flowsheet. Since its commercialization in the late 1960s, steady improvements in the performance and efficiency of the solvent-extraction reagents and equipment, combined with significant developments in leaching and electrowinning, have made an ever-widening range of ore types amenable to this technology. Following successful implementation on all major continents, a large proportion of growth in recent years derives from the re-emergence of copper solvent extraction in the Central African Copperbelt. This review provides a brief history of the development and evolution of copper solvent extractants and mixer-settler contactors, and the significance of the Copperbelt region in achieving commercialization and acceptance of the technology. The opportunities and challenges presented by the abundant high-grade oxide ores of the Copperbelt are contrasted with the processing of solutions derived from the low-grade mixed oxide–sulfide ore bodies that are prevalent in other geological regions. The current status of hydrometallurgical copper production in the African Copperbelt, within a global context, and a medium-term outlook for the technology are discussed.

Jul 5, 2023

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 22nd August, 1979. Dr M. G. Atmore (President) was in the chair and declared the meeting open at 16h00. Obituaries President: It is my sad duty to announce the death of the following Members of the Institute : Brigadier R. S. G. Stokes, Honorary Life Fellow and Past President ; J. A. Arthur, C. L. Cartwright, R. B. Greaves, A. A. Haynes, G. Ross, M. W. Richards, W. T. Stobart, E. Veres, G. V. White, and A. G. Williams, Life Fellows; A. J. H. Pole, D. T. McMurray, P. G. O. Pretorius, A. E. D. Rubidge, A. M. Seccombe, and R. R. Uren, Fellows; R. E. Oltman, R. B. Richardson, and G. P. Rundle, Members; S. F. Dench and S. van Wyk, Associates. As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, please rise and observe a few moments' silence. Minutes President: May we confirm the minutes of our last Annual General Meeting, which was held on 23rd August, 1978, as published in the November issue of the Journal? Agreed.

Jan 1, 1979

By K. E. H. K. Ishak, S. R. M. Zan

Cement production requires significant energy, and entails high costs and CO2 emissions. This is because the clinker requires very fine grinding. Grinding aids can improve production and fineness and decrease energy consumption by reducing the agglomeration of particles and protecting the balls and liners in the mill. In this study we compare the effects of three different grinding aids on clinker grinding using a ball mill. A commercial grinding additive, triethanolamine (TEA), and two industrial grinding aids (GAA079 and GAA088) were compared by ball milling tests, with additions of 0.05, 0.25, 0.50 and 1.00 wt%. The industrial grinding aids were characterized using gas chromatography-mass spectrometry (GC-MS). Particle size and morphological analyses were performed using SEM and XRD. The best results were obtained with 0.25% GAA088, which has a higher active component of diethanolamine isopropanolamine (DEIPA) than TEA. The unique combination of TEA and DEIPA in GAA088 enhances grinding efficiency and significantly improves the particle size distribution compared to TEA alone.. The grinding aids produced smooth rounded particles, which have a smaller specific surface area, enhancing the quality of the cement. XRD showed no significant structural distortion with or without grinding aids, and it was also found that the grinding aids helped decrease ball coating during grinding. The use of grinding aids can significantly improve clinker production and fineness while decreasing energy consumption, which can help reduce the costs and CO2 emissions associated with cement production.

Sep 6, 2023

By L. von Ketelhodt

During the period October 2003 to June 2004, a containerized optical sorting pilot plant was operated at Kloof Gold Mine on a waste rock dump. In this paper, we describe the test work and its results leading to the decision to operate this pilot plant. This paper presents the operational data and financial figures achieved during this project, in particular, for the month of June 2004 when the plant was run at full capacity on three shifts, 24 hour operation. These results are also extrapolated and presented to show the profitability of such an operation at today?s gold price levels and cost structure.

Jan 1, 2009

By T. M. Louw, L. Auret, S. M. Bradshaw, F. F. Noelle

Modern industrial processes undergo frequent process state shifts due to changes in demand, feedstock or maintenance operations. Multimodal continuous process monitoring is therefore required for effective plant operation. Steady state analysis is a key component in effective multimodal monitoring. Various issues still remain in determining the starting and ending times of transition states. High dimensionality of process data is a characteristic that makes it difficult to select variables to consider when conducting steady state analysis. In order to address these problems, steady state detection on the principal component space is proposed. First, data undergoes principle component analysis to reduce dimensionality, then existing multivariate steady state detection algorithms are applied on the principle component scores. A novel algorithm, threshold PCA-SSD, is proposed and compared to an existing technique for steady state detection. The algorithms are investigated on high dimensional synthetic data Keywords: Multimode process, steady state detection, principle component analysis

Jan 1, 2020

By G. Popplewel

Commencing with the Pre-Feasibility Study (PFS) conclusions, the Orapa 3 process design evolved through a phase of value-engineering studies. An overall re-evaluation of the originally proposed process design was necessary both in order to address the interim increase in target throughput from 9.8 Mtpa to 12 Mtpa as well as to increase capital efficiency. In the interests of clarity, the PFS process design for Orapa 3 has been omitted from this paper, as it is no longer relevant. Recognition is however due to those engaged in earlier phases of the Orapa 3 project with respect to fundamental mass-balancing modelling; and ore and diamond characterization, which fanned the basis for the process design that has evolved from feasibility study activities.

Jan 1, 2010

By J. J. Cilliers, J-A. Lamamy, J. N. Rasera, K. Hadler

Production of oxygen on the moon can be achieved by reduction of lunar soil. One such reduction technology, hydrogen reduction, favours a high proportion of ilmenite in the feedstock. Ilmenite is present in lunar soil as a minor mineral phase, but it can be upgraded using electrostatic separation. This study presents the results of a preliminary investigation into the operating parameters and sensitivities of a free-fall electrostatic mineral separator for lunar applications. Samples of ballotini and ilmenite as well as simple binary mixtures of the two were tribocharged on copper and passed through a uniform electrostatic field. The field is varied to change the electrostatic force acting on the particles. The proportion of material reporting to the positive electrode collectors, negative electrode collectors or the central collector was measured to determine the separation performance. The data confirmed that the charge transferred from the tribocharger to each species is in agreement with the triboelectric series; ballotini was found to charge positively on copper and ilmenite negatively. Particle-particle contacts were dominant, however, resulting in a somewhat symmetrical particle distribution in the collectors. These findings indicate that the copper tribocharger design requires optimisation in order to substantially increase particle-wall contacts. Four binary mixtures with feed grades of ilmenite ranging from 5% to 20% were prepared and tested. This study found that a higher ilmenite head grade resulted in a higher concentrate grade (26.3% from a head grade of 20%) with low recovery (3.4%). In contrast, the lower feed grade resulted in a low concentrate grade but higher recovery. The mass yield of ilmenite was 1.4 times greater for the highest-grade feed than for the lowest. A subsequent study into the reprocessing of middling fraction found a nearly constant relationship between cumulative grade and recovery. This is the first investigation into the effect of feed grade on the concentrate grade and recovery for lunar mineral processing. Keywords: Lunar resources, beneficiation, electrostatic, SRU, ISRU

Jan 1, 2020

By P. Mühlen, C. Nelson

Process control optimisation depends a lot on the availability of timely data from production to give operators a chance to make adjustments before potential process upsets or disruptions happen. A lot of data is already available with newer and updated machine technologies, but what about the process upsets coming from the raw materials that we use? They are natural products and therefore they are not of a stable composition or mineralogy. The production process depends on a certain chemical or mineralogical stability of the raw materials when they come to a roaster, kiln or sintering stage. Only then can the proposed reactions take place and the equipment be operated at stable temperatures. Laboratory analytical technologies have the limitation that they depend on representative samples and have a long time delay. Therefore online (real time) analysers are used nowadays in mining applications to obtain an early indication of the actual mined or to-be-processed ore. Most available technologies can only analyse inorganic content on an oxide or elemental level. Near infrared (NIR)- based online analysers can overcome that limitation and give a real time analysis of organic as well as inorganic composition, if required on a mineral level. The paper will present two case studies where the NIR online technology was successfully adapted.: a) Optimising refractory gold ore processing at the Goldstrike roaster operation b) Optimising the sinter process at a Japanese manufacturer. Keywords: Analyser, NIR, online, realtime, gold, roaster, iron ore, sinter, mineral phase analysis

Jan 1, 2020

By P. Hand

Most coal plants must run under conditions of varying feed conditions or are asked to produce qualities different from that used in the design. This can cause overloaded conditions as the ?bottlenecks? within the plant, depending on plant operation or as the feed changes. During plant design, geological information can be used to determine washability envelopes and blends that may be expected. Historical data can also be used to develop a size distribution envelope as well as to assign reasonable models for each of the unit processes. In operation, a plant can be sampled to determine changes and to refine process models. The information obtained can then be used in an accurate simulation to define how the plant can deal with the changing environment. This paper uses Limn: The Flowsheet Processor to simulate the coal plant in detail and will produce an accurate model, in terms of equipment sizing as well as water, medium, and solids balance, for each change in feed condition. It will show examples of running the simulation through complete density and size ranges and will determine the equipment required to address each part of the performance envelope.

Jan 1, 2010

By N. D. Fernandes

Labour-intensive narrow reef stoping, as traditionally practised in South African gold and platinum mines, is almost unique in the modern first-world mechanized mining environment. Shortcomings of the system include the ever increasing cost of labour, a cap on achievable productivity and a poor safety record, particularly in the field of rock-related accidents. In the absence of sustainable alternative technologies, the South African mining industry has spent millions of rands improving the present system, focusing on improving workplace safety. This paper details the changes to stope support at Impala Platinum?s Rustenburg operations, and the impact on rock-related safety performance. Keywords Stope panel support, narrow reef stoping, improving workplace safety.

Jan 1, 2011

By L. Schernikau, W. H. Smith

Oil, coal, and gas account for approximately 80% of global primary energy, but only a portion of total airborne CO2 eq (approx. 35% at GWP20 to 65% at GWP100), even though they account for 95% of total measured CO2 emissions. The benefits of these energy sources, as well as their related costs, are not all incorporated in current energy policy discussions. Global greenhouse gas policies must include documented changes in measured airborne CO2 eq to avoid spending large amounts of public funds on ineffective or sub-optimal policies. The authors examined airborne CO2, which is less than half of emitted CO2, as well as reported CH4 emissions and the global warming potential of CH4 as published by the IPCC for coal and natural gas. The surprising conclusion is that surfaced-mined coal appears ‘better for the climate’ than the average natural gas, and all coal appears beneficial over LNG. Therefore, current CO2-only reduction policies and CO2 taxes are leading to unintended consequences and the switch from coal to natural gas, especially LNG, will not have the desired impact of reducing predicted future global warming; in fact, quite the contrary. A large portion of anthropogenic global warming is attributed by the IPCC and IEA to CH4, but it must be noted that CH4 emissions from natural sources and from agriculture account for approximately 40% and 25% of annual global CH4 emissions respectively. Energy accounts for about 20% of documented CH4 emissions. CO2 contributes only approximately 35% of annual airborne anthropogenic GHG emissions after accounting for CH4, over a 20-year horizon. At a 100-year horizon, the contribution of CO2 increases to approximately 60%. Energy policies that do not consider all GHG emissions along the entire value chain will lead to undesired economic and environmental distortions. All carbon taxation and CO2 pricing schemes are incorrect and need to be revised. At IPCC’s GWP20 an approximately 2%1 higher loss of CH4 across the value chain prior to combustion of natural gas versus coal will lead to ‘climate parity’ of coal with natural gas. According to public data, natural gas value chains have high CH4 and undocumented CO2 losses. On a global average, using only IEA-documented CH4 data, natural gas emits approximately 15% more CO2 eq than surface-mined coal, over a 20-year horizon. This difference will increase as the use of shale gas and LNG expands. Investors should support all energy systems in a manner that avoids an energy crisis, including intermittent renewable energy systems where they make sense. If CO2 emissions need to be reduced, one of the most effective ways would be to install ultra-supercritical power plants with CCUS technology. However, the undisputed benefits of increased CO2 concentrations in the atmosphere because of its promotion of photosynthesis and plant growth effects (fertilization) need to be considered in energy policy decisions as well. The authors suggest that future research and development should concentrate on reducing net emissions from fossil fuel power plants and providing cost-effective and reliable new conventional power generation capacity, utilizing clean coal and clean natural gas technology.

Mar 2, 2022

By A. Çelik

Wheel loaders are widely used in many sectors due to their mobility, operational flexibility, and low costs. The literature is mainly focused on improving the hydraulic, mechanical, and electronic subsystems of these machines in terms of efficiency or developing strategies for controlling these systems. In this study, the effects of the loader operator and different working conditions on the loading performance were investigated. The study was carried out at the Can Lignite Enterprise (CLI), which is a major coal producer in Turkey. In the study, which lasted approximately four months, a total of 808 measurements were performed to investigate seven different scenarios. The effect of a single parameter on loading performance was investigated in the first six scenarios. The results showed that the biggest impact on loading performance was caused by the operator's experience with 63.4%. On the other hand, the worst and most ideal working conditions determined from the first six scenarios were tested in the seventh scenario. It was tested as a script. The test results showed that the loading performance was 285.5% more effective under the most ideal operating conditions compared to the worst operating conditions. In addition, in the study, the loading performances of five loaders with four different capacities were examined in terms of energy efficiency and it was determined that the Kawasaki 115 work machine, which has a higher model and lower engine operating hours, was more advantageous. In the study, various suggestions were developed in parallel with the research results. The most prominent and easiest to implement of these suggestions is related to the selection of the loader operator.

Nov 27, 2024

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By Dave Deglon, Andrévan der Westhuizen

Objectives ?Survey typical Met Accounting streams at the Zincor refinery ?Determine Precision in Metal Conc?s Measurements for Monthly Met Balance ?Determine the Components of Variance in these Met Acc Values (Sampling, Preparation, Analyses) ??Common plant practice? should be mirrored even though not always in perfect agreement with ?laid down procedures? or ?good practice? ?Mass Measurement and Inventory Measurement was considered in less detail ?not reported here

Jan 1, 2005

By M. Ye. Scheglov, G. I. Voiloshnikov, S. M. Ryakhovsky, V. E. Dementyev, V. N. Alekseev, N. S. Voiloshnikova

Irgiredmet has substantial experience on RIP and RIL technology for gold recovery, having started development of ion exchange technology in 1964. Irgiredmet specialists were involved in the majority of RIL and RIP projects in the former Soviet Union and Russia, and took part in commissioning of practically all plants using ion exchange technology. Laboratory and pilot plant tests were conducted to develop process design criteria for designing 15 RIP plants of the former USSR using bifunctional macroporous anionite AM-2B or its analogs. This paper is devoted to the laboratory, pilot plant testing and introduction of RIP technology conducted in cooperation with GC Pertopavlovsk. Medium base resin PuroLite S992 (PuroGold) was used as adsorbent. Some adsorption regularities and the affinity of resin to metal cyanide complexes were studied. Laboratory batch and continuous pilot tests on resin-in-pulp process were held for oxidised ores from Pioneer, Albyn and Malomyr mines (Amur region, Russia) owned by the Petropavlovsk company. A simplified flowsheet for gold elution and resin regeneration was developed. Alkaline cyanide solution was used as gold eluent and gold was recovered from eluates by electrowinning. Process design criteria were developed on the basis of the testwork results, and the plants were designed and constructed by GC Petropavlovsk. The RIP plant at Pioneer was commissioned in May 2008, at Malomyr in August 2010, and at Albyn deposit in December 2011. These plants are currently in operation at design performance at throughputs from 3 to 6.5 Mt/year. The primary gold ores of Pioneer and Malomyr deposits are refractory to cyanidation; Irgiredmet also completed continuous testwork on RIP technology using medium-base resin for pressure oxidation (POX) residues derived from their flotation concentrates. In 2019 a hydrometallurgical plant for the treatment of refractory gold concentrate after POX was commissioned at Pokrovsky mine (Amur region). Keywords: Gold ores, cyanidation, RIP, RIL –processes, ion exchange resin, medium base resin, adsorption, elution, electrowinning

Jan 1, 2020

By M. Åstrand, M. Johansson

"Advanced planning and automation are increasingly important in modern mines. Sophisticated methods for long-term mine planning are often used, and the advent of autonomous machines makes the actual operation more predictable. However, the interface between these two timescales, i.e. the scheduling of the mobile production fleet, often limits the ability to operate mines at maximum profitability. We show how scheduling the production fleet in an underground mine can be modelled as a flow shop. A flow shop is a general abstract process formulation that captures the key properties of a scheduling problem without going into specific details. Thus, the flow shop enables mine scheduling to reap the benefits of scheduling research from other industries. We review recent results from the mining community and the flow shop community, and introduce scheduling methods used in these two fields. This work aims at providing value to researchers from the mining community who want to leverage their skill set, as well as to theoretical researchers by presenting the mining process as a potential application area. Lastly, we discuss the results, and outline some future challenges and opportunities facing the industry. IntroductionThe margins in underground mining are constantly under pressure since costs increase as the mine becomes deeper. One major component influencing the operational performance, and thus the profitability of an underground mine, is how the mobile machinery and staff are coordinated. Today, the coordination of the underground fleet, i.e. scheduling of the machines, is mostly done manually, with methods that are stretched to their limit and with no guarantees on performance. According to a survey of more than 200 high-level executives in mining companies around the world (Mincom, 2011), the top challenge for modern mines is to maximize production effectiveness, rather than improving the reliability of individual items of equipment. This highlights the importance of coordination on a system level.The effectiveness of mine production can be increased by introducing supportive algorithms in the scheduling process. These algorithms enable mines to construct optimized schedules with respect to custom metrics. Additionally, manual scheduling is a tedious and error-prone task where the performance is heavily dependent on the scheduler. To reduce the staff dependency, supportive algorithms can help to achieve more uniform outcomes, resulting in a more predictable process. In turn, this increases the transparency of the mining process through the entire production chain. It is worth noting that automatic scheduling has proved beneficial in many other industries, such as chemicals and metals (Floudas and Lin, 2004; Tang et al., 2001)."

Dec 1, 2018

By C. T. O’Connor

Since the first IMPC took place in London in 1952 there have been many developments in our understanding of flotation, both in terms of chemical and physical factors influencing the process. Many of these developments have been captured in the proceedings of thirty congresses that have taken place since that first event, as well as in numerous journal papers and special volumes dedicated to flotation. This paper attempts to highlight the individual contributions which many eminent researchers and engineers have made over the past 70 years towards extending our understanding of, especially, the effects of chemical factors on flotation. Although the focus is mainly on more fundamental aspects, it seems that the ‘pull’ of practice has often preceded the ‘push’ from laboratory-based research. As the fundamental understanding of the role of chemical factors on flotation continues to be developed, the major challenge remains to transfer this knowledge effectively into the domain of operations of this profoundly complex process.

Jan 1, 2020