Search Documents

By John G. Parker

Important quantities of gold, silver, platinum-group metals, selenium, tellurium, and arsenic are recovered in the processing of copper concentrates. The objective of this Bureau of Mines study was to determine the occurrence of these elements in copper ores and to trace their distribution during subsequent processing steps. The study describes the important areas supplying concentrates, precipitates, and unrefined copper to the copper smelting and refining industry in a composite of the years 1971-74. The relative importance of these areas as a source of the respective byproducts is assessed. The lack of certain quantitative and assay data, recycling of dusts and slags, and the addition of scrap to the feed often complicates calculations and estimations of the byproducts in the smelter-refinery throughputs. Such volatile or low-boiling point elements as arsenic, selenium, and tellurium may be lost in gaseous and other emissions in various processing stages, or they may be concentrated in slags and residues for which samples were not available. The effects of antipollution legislation to improve control of sulfurous and other emissions that may affect recovery of certain byproducts was noted. A section on newer technology illustrating hydro-metallurgical techniques that may affect the recovery of minor metals is included.

Jan 1, 1978

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By B. J. Barfield

Standard erosion plots (4.6 m by 22.1 m on 9 percent slope) were constructed on the Alston Surface Mine of Peabody Coal Company in Western Kentucky to evaluate the effects of placement technique and density on the erodibility and eroded size distribution from mine spoil and reconstructed topsoil. PLots were constructed with a dozer and scraper pan from shale spoil material, topsoil (A horizon) and subsoil (B and C horizon mixture) using soils stockpiled at the Alston Surface Mine. Plots were evaluated under fallow conditions with a tilled plot surface and two compacted conditions. One compacted condition was generated by tracking the surface with a dozer and rolling with a loaded scraper pan. The second was generated by rolling the surface with a solid wheel compactor. Rainfall was supplied with the Kentucky Rainfall Simulator at a rate of 63.5 mm h-l with the plots in three different soil moisture conditions; dry, field capacity, and very wet. Runoff was evaluated for flow rates, sediment concentrations, and aggregate and primary particle size distributions. Sediment yields and the Universal Soil Loss Equation E130 indexes were calculated from the data for each plot. The erodibility was calculated from the tilled plot data using a weighted soil loss and E130 value from the dry, field capacity and wet runs, and a cover management factor calculated for every other condition. For the topsoil and subsoil plots, sediment yield was greatest for the dozer scraper pan plots and lowest for the tilled plots. For the shale plots, erosion rates from the wheeled compacter plots were the highest and tilled plots the lowest. Average erodibilities were 0.14, 0.38, and 0.41 tons ac h ft-1 tonf-1 in-1 hundred ac-1 for the shale, subsoil, and top-soil plots. Cover management factors for each plot were 1.29, 1.42, and 1.17 for shale, topsoil and subsoil plots compacted with the solid wheeled compacter and 1.29, 3.79, and 2.51 for shale, subsoil, and topsoil plots compacted with the dozer scraper pan conbination. The accuracy of the Wischmeier erodibility nomograph was evaluated on the data collected. Erodibilities were accurately predicted for the topsoil plot and poorly predicted for the sub-soil plot. The accuracy of the CREAMS procedures for predicting the composition (size distribution) of eroded particles was also evaluated. The composition was well predicted for the topsoil plots, moderately well predicted for the shale plots and poorly predicted for the subsoil plots.

Jan 1, 1983

By Michael G. Zabetakis

Limits of flammability of normal propyl nitrate (NPN) vapor were investigated at ambient and elevated temperatures. Minimum spontaneous ignition and decomposition temperatures were determined with laboratory apparatus over the pressure range from 0 to 4,000 p.s.i.g. Flame speeds and the detonation susceptibility of NPN vapor were measured at elevated temperatures. Stable detonation was obtained with liquid NPN at elevated temperatures, and the detonation velocity was determined to be between 4,700 and 5,100 m./sec.

Jan 1, 1962

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963

By Lowell Stroud

This report is the third in a series presenting equilibrium vapor-liquid data for helium-bearing natural gases. The first two reports contained phase data for the gases processed for helium at the Bureau of Mines Amarillo and Exell, Tex., helium plants. The present report offers similar information for a lower-helium-content (0.75 mole-percent) natural gas to be processed in the Department of the Interior's long-range helium-conservation program. A windowed-cell apparatus was used to obtain 218 samples of equilibrium vapor and liquid phases at 73 experimental conditions ranging in temperature from -100° F to -275° F and in pressure from 100 to 500 psi. From the phase data, the condensation characteristics, helium solubility, and equilibrium-vaporization-coefficient data for helium, nitrogen, and methane were evaluated. The effect of using a. preliminary hydrocarbon trap upon the subsequent vapor-liquid compositions is reported. A brief comment regarding the composition effect of passing the gas through a gasoline-removal unit is also included.

Jan 1, 1963

By Harold P. Rue

The problem of removing hydrogen sulphide from natural gas has become within the last few years one of major importance to the natural gas and petroleum industry. Several gas fields in the United States produce natural gas containing hydrogen sulphide, and a number of oil fields produce gas which contains hydrogen sulphide. 3 The percentage of hydrogen sulphide in natural gas produced in these fields varies from a fraction of 1 per cent t6 as high as 20.5 per cent by volume. 4 Hydrogen sulphide is probably the most toxic gas associated with natural gas,5 and from the standpoint of health and safety it is important that the hydrogen sulphide be removed if the gas is to be used for domestic purposes. Hydrogen sulphide, besides being toxic and therefore a hazard to animal life, is under certain conditions an active corrosive agent and very destructive to equipment. 6 The annual loss caused by the corrosive action of hydrogen sulphide on equipment amounts to hundreds of thousands, perhaps millions, of dollars. 7 The largest percentage of natural gas produced in the United States comes from wells which also produce oil. This associated gas invariably carries with it light fractions of petroleum, which when separated from the gas, condense to the liquid form at ordinary temperatures and pressure. Commercial application is made of this natural condition, and "wet gas" is processed to obtain so-called natural gasoline by employing the principles of absorption, adsorption, or compression and subsequent expansion accompanied by cooling. In the manufacture of natural gasoline from wet gas which contains hydrogen sulphide, if this contaminating gas is not first removed, some of the hydrogen sulphide may oxidize to form free

Jan 1, 1932

By Earl Redman

The Juneau Gold Belt portion of the Juneau Mining District has historically had the greatest mining and exploration activity within the district. Between 1880 and 1983, the mines within the Juneau Gold Belt produced 6.7 MM oz gold, 3.1 MM oz silver, and 45 MM lbs lead, which had a total value of about $157,000,000 at the time of production. This report summarizes Bureau of Mines work completed in 1986, the second year of the Juneau Mining District study. Fifty mines, prospects, and occurrences were examined and 638 samples were collected for analysis during 1986. Metallurgical samples were collected from seven deposits and preliminary tests of cyanide amenability have been completed for five of these. The simultaneous discovery by private industry and the Bureau of gold-bearing quartz veins cutting diorite gneiss recently exposed by the retreat of the Herbert Glacier is the most notable result of work during 1986. This location yielded gold values up to 7 oz/st.

Jan 1, 2011

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By K. P. V. Lei

The Bureau of Mines investigated molten-salt electrorefining as a practical method for reclaiming vanadium from vanadium scrap. An electrolytic process utilizing a KC1-LiC1-VC12 electrolyte at 615° C was developed for producing ductile vanadium with a purity over 99.9 percent. The recovery of the vanadium in the cell feed ranged from 88 to 93 percent with a current efficiency from 83 to 95 percent.

Jan 1, 1967

By Martin H. Rogoff

This publication combines a critical review of the literature on the microbiology of coal with an introduction to those areas of microbiology related to studies of coal as a biological material. The attack on coal by microorganisms as yet remains doubtful. Only the low-rank coals contain an indigenous microbial flora, and even these organisms are not peculiar to coal, but are common soil and water forms. No experimental data have as yet been presented, either in the literature or in the present work, which unequivocally demonstrate the oxidation of coal by microorganisms. Reasons for the resistance of coal to such attack, including insolubility, physicochemical structure, steric hindrance of enzyme action, and the presence of antibiotic materials in coal are discussed. Microorganisms do attack large aromatic molecules and the mode of oxidation of aromatic ring systems by bacteria is presented. Well-defined pathways are known for the oxidation of polycyclic compounds with one to three rings, and these paths with their key intermediates are described and related to the possible oxidation of coal.

Jan 1, 1962

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

By E. Chin

The Asia and the Pacific region has large mineral resources of antimony, barite, bauxite, bismuth, copper, fluorspar, gold, graphite, iron ore, magnesite, mica, rare earths, salt, talc and pyrophyllite, titanium, zinc, and zirconium. The region overall lacks large resources of oil and natural gas, but it has large resources of anthracite and bituminous coal. In terms of exploitation, many minerals, metals, and fuel are produced in significant quantities in the Asia and the Pacific region as shown in table 1. Collectively, the area accounts for a substantial amount of the world production of antimony, barite, bauxite, fluorspar, gold, graphite, ilmenite and rutile, iodine, iron ore, lead, magnesite, manganese, nickel, salt, tin, tungsten, and zinc. Total coal production of the region exceeds 1.6 billion metric tons. The production of bituminous coal accounts for more than 80 % of the total output. China is the region's largest coal producer, with an output of almost 1.1 billion tons. Other major producers are Australia and India. The combined production by Australia, China, and India is more than 1.5 billion tons or 93 % of the area's output. The remainder of the coal output in the region comes from Afghanistan, Cambodia, Indonesia, Japan, the Korean peninsula, Malaysia, Mongolia, New Zealand, Pakistan, the Philippines, and Taiwan. The production of crude oil throughout the Asia and Pacific region is close to 2.4 billion barrels. China and Indonesia together account for 67 % of the total output. The remainder of the output is primarily from Australia, Brunei, India, and Malaysia. Indonesia is the largest producer of natural gas in the region with an output of close to 58 billion cubic meters, followed by Malaysia and Australia with 23 and 22 billion cubic meters, respectively. Other producers in the region of lesser stature by output include Brunei, China, India, and Pakistan.

Jan 1, 1993

By E. L. Rawlins

The development of commercial natural-gas reserves in the Michigan stray sandstone horizon of central Michigan during the past few years has resulted in expansion of the natural-gas industry in that State. The location of the natural- gas reserves of Michigan in the general vicinity of domestic and industrial markets is of economic importance, and in supplying these markets with natural gas a reasonable knowledge of the extent and availability of the reserves is needed in formulating regulations for drilling gas wells and producing natural gas, in analyzing the feasibility of projects to construct natural-gas transmission lines, in promoting and developing markets for the domestic and industrial consumption of natural gas, and In solving many engineering and economic problems common to the natural-gas industry. The development of the natural-gas industry in Michigan has been related closely to the development of oil production. The potential oil production of Michigan is comparable with that in most of the eastern oil-producing States. The development of oil production probably will continue, especially in the central Michigan Basin area; and as wells are drilled to deep horizons in the search for oil, more knowledge will be obtained of the gas reserves in formations above the oil- bearing horizons.

Jan 1, 1936

By R. G. Knickerbocker, T. E. Evans, D. R. Torgeson

"INTRODUCTION Sponge iron is a product resulting from the reduction of an iron oxide at such a low temperature that fusion does not occur, and the reduced particles retain substantially the same shape as the original ore. The removal of oxygen in the reduction process leaves the metal porous and reactive. Sponge iron may be compared in general to a chemically precipitated substance insofar as reactive properties are concerned. The high specific surface and the orientation of metallic structure are factors which probably contribute to the reactive properties of sponge iron.The term ""gaseous reduction,"" as applied to iron ores, required clarification. Strong evidence exists, for example, that ore is partly reduced to sponge iron by carbon monoxide in the blast furnace at temperatures around 800° C. at a point that may be as high as 30 feet above the tuyores. In 1923 and 1924, Sims and Wood attempted to reduce iron oxide with carbon in an Arsem vacuum furnace at 980° C. These investigators found that only 6 percent of the iron was reduced to metal when the iron oxide-carbon mixture was heated for 1 hour under evacuated conditions, whereas at atmospheric pressure 70 percent of the iron was metallized. Their results indicate that the process of iron-ore reduction at temperatures below the melting point of the ore may proceed largely, if not entirely, by the action of reducing gases even when the reducing agent is solid carbon. Therefore, the term ""gaseous reduction,"" as used heroin, is defined as a process in which iron ore is brought into intimate contact with a reducing gas produced in separate-equipment from the reduction chamber itself.A large amount of pilot-plant development on gaseous reduction of iron ores has been carried out by the Bureau of Mines at the Boulder Experiment Station and had as its objective the reduction of fine iron ore by means of producer gas. The use of use gas was prompted by two considerations: First, the possible utilization of large reserves of Western noncoking bituminous coals and lignites contiguous to iron-ore drewwing; and second, an investigation of the results that might be achieved in the pilot-plant gaseous reduction of fine iron ores by means of a relatively reducing gas. The results obtained, it was felt, would be of considerable value in indicating the direction which gaseous reduction experimentation must take for the development of a commercially practicable and economic process for the production of sponge iron."

Dec 1, 1946

By T. H. Jeffers

The Bureau of Mines conducted a laboratory investigation of copper electrowinning from electrolytes produced by solvent extraction. The purpose of the research was to gain a better understanding of the fundamental relationship between copper electrowinning conditions, anode corrosion, and cathode purity. Processing variables were evaluated in a cyclic semicontinuous system in which the depleted electrolyte was used to strip copper from loaded organic extractant. For the production of high quality copper cathodes, the electrolyte was dosed with cobalt and stripped of organic solvent extraction reagent. An optimum cobalt addition of 60 ppm, and removal of the entrained extractant with activated carbon provided the best conditions for electrowinning copper containing the least amount of lead and controlling anode corrosion. As little as 13 ppm of the entrained organic extractant, LIX 64-N, significantly accelerated anode corro-sion. However, the addition of 1,000 ppm of organic diluent kerosine did not affect anode corrosion. After cobalt dosing and removing the entrained extractant, cathodes containing less than 2 ppm lead were consistently electrowon at widely varied current densities, electrolyte copper and acid concentrations, and temperatures. Dosing of the electrolyte with selected impurities including magnesium, aluminum, manganese, and iron did not affect the cathode purity. However, 0.05 giL of chloride ions markedly increased anode corrosion and the sub-sequent transfer of lead to the cathode copper.

Jan 1, 1985

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By M. E. Hawkins

This Bureau of Mines report provides information on all of the 329 proved salt domes in the Gulf Coastal States and offshore area of the United States. It includes specific data related to location, depth to the cap rock and to the salt, storage facilities for LPG, and production of salt, sulfur, petroleum, and rock related to or associated with the dome structure in the subject area. Also included is a brief history of the salt, sulfur, and petroleum industries as related to the salt domes. Gulf Coast salt domes were the scene of the first discovery of a large deposit of rock salt in North America, the birthplace of the Frasch sulfur industry, and the location of the first large oil gushers that ushered in the modern liquid fuel age.

Jan 1, 1966