Search Documents

By B. K. Shibler, W. G. Sandell, G. M. Potter, H. D. Snedden

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, examining 'engineers of the Bureau of Mines collected samples from seven manganese properties in Grand and beery Counties, Utah. These were supplemented by five samples submitted by property owners. Since all of the ores were too low-grade for use in producing ferromanganese for steel manufacture, some means of beneficiation was required to produce marketable concentrates, and metallurgical studies were made on each of the samples.Most of the ores Investigated are similar in one respect: At least part of the 'manganese oxide areas contains minute inclusions of gangue. This occurrence materially enhances the complexity of the ore, partly by .increasing the complexity of mineral association, but largely through making manganese-quartz liberation more difficult. In such ores, there is a marked tendency for the manganese minerals to be retained as shells or coatings on the surfaces of quartz particles when crushed. Particles of this type represent considerable loss of manganese in tailing, if gravity-concentration methods are employed, or tend to' float, thus carrying an appreciable quantity of gangue into the concentrate, if treated by flotation.Plus 48-percent manganese sinters were made from some of the ores tested, but, in general, intimate association of manganese minerals with silica limited the degree of beneficiation attainable."

Dec 1, 1947

By Earl C. Redman

The Juneau Gold Belt, centered on Juneau and approximately 120 miles long by 10 miles wide, stretches from Berners Bay on the north to Windham Bay on the south (fig. D-l). Access within the Juneau Gold Belt is provided by the Glacier, Thane, and North Douglas Highways. The Glacier Highway extends northwest from Juneau for approximately 40 miles to Echo Cove, and the other two roads end 5.5 miles southeast and 12.6 miles west from Juneau, respectively. None of these roads connect with other highway systems and access to other areas is restricted to airplanes, the State ferry system, and commercial barge lines. BUREAU ACTIVITIES The majority of lode gold produced in Alaska came from the Juneau Gold Belt portion of the Juneau Mining District. To evaluate the economic potential of the Gold Belt, the Bureau located 173 mines and prospects within the area. A total of 263 ad its and shafts were found and 56,650 feet of underground workings were mapped. The Bureau collected and analyzed 1,557 samples during the study. In addition, considerable detailed geologic map-ping was done in the vicinity of the mines and prospects from which ore control models were developed.

Jan 1, 2012

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By H. R. Babitzke

As part of a continuing project to develop refractory metal alloys for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation strengthening techniques to improve the properties of columbium alloys. The purpose was to investigate the effects of hafnium, tungsten, and boron on the formability, strength, and oxidation resistance of columbium. The experiment was of factorial design with two replications which called for 72 ingots of 36 basic compositions, weighing 150 grams each. Hafnium, tungsten, and boron were evaluated at 3, 3, and 4 levels, respectively. Values of alloy content are all in atomic percent. The highest strength observed was 29,000 psi at 1,200° C for alloys Cb-15Hf (No. 3), Cb-7.5Hf-5W-2B (No. 14), and Cb-15Hf-5W-2B (No. 15). At 1,200° C, the ternary alloy Cb-15Hf-5W (No. 6) which has shown good properties in previous Bureau of Mines investigations was the most resistant to oxidation For boron additions, the alloys oxidized more readily with increasing amounts of this element. The fabricability of the alloys high in boron became increasingly difficult, resulting in an inadequate number of alloys required for a complete statistical analysis for all the tests. As a result of the decrease in ductility, an insufficient quantity of tensile samples were available for a proper analysis for the high-temperature strength data.

Jan 1, 1970

By D. Harrington

"One of the underlying reasons for the establishment of the United States Bureau of Mines was the desire to promote greater safety in the mining and allied industries. Safety continues to be an important feature in the work of the bureau, and during the fiscal year 1929-30 the Bureau of Mines allotted $387,510 to the safety division out of a total appropriation of $2,249,670 (other than for helium).The safety division personnel consists of 22 engineers, 2 mine safety commissioners, 3 senior foreman miners, 18 foreman miners, 16 first-aid miners, 16 clerks, 10 cooks, and 3 laborers, a total of 90 persons. These safety workers are distributed through the 10 districts into which the United States has been divided for administration purposes. During the year 3 engineers, 1 senior foreman miner, 4 foreman miners, and 4 first-aid miners left the service. In general these men left the service to take up more lucrative positions.The 10 all-steel mine-rescue cars have headquarters as follows: Car 1, Reno, Nev.; Car 2, Raton, N. Mex.; Car 3, Pittsburgh, Pa.; Car 4, Terre Haute, Ind.; Car 5, Pineville, Ky.; Car 6, Pittsburg, Kans.; Car 7, Huntington, W. Va.; Car 8, Duluth, Minn.; Car 9, Butte, Mont.; Car 10, Des Moines, Iowa. There is also a mine-rescue car with headquarters at Juneau, Alaska. In addition, there have been established 11 mine rescue stations as follows: Birmingham, Ala.; Berkeley, Calif.; Seattle, Wash.; Evansville, Ind.; Jellico, Tenn.; McAlester, Okla.; Norton, Va.; Vincennes, Ind.; Wilkes Barre, Pa.; Salt, Lake City, Utah; and Pittsburgh, Pa.Every mine-rescue car and station is fully supplied with equipment and devices for use in case of mine fire or explosion, and at each station is an up-to-date automobile truck. At time of amine disaster the bureau's forces are immediately placed at the disposal of the authorities, State or company, with a view to giving such assistance as may be desired or available.The activities of the safety division at ordinary times are directed largely to securing and disseminating data on safety in mining. Among the numerous studies made, or being made, concerning safety and health in mining are those in connection with the causes and methods of prevention of mine explosions, explosibility of dust and gases, explosives and blasting, haulage, electricity, falls of persons or material, ventilation, dusts, high temperatures, timbering, lighting, machinery, and in fact practically anything which results or may result in acci¬dents of any kind in or around mines."

Nov 1, 1930

By J. B. Stott

The performance of an adiabatic calorimeter for measuring heats of oxidation of coal is assessed and suggestions made for its improvement and calibration. The use of magnetic analysers for measuring small oxygen deficiencies in air is described and three different methods of measuring the output for such a meter are characterised. The occurrence of spontaneous heating in an 800 tonne heap of Wyoming coal is briefly described. The major part of the report deals with the oxidation of Pittsburgh seam and Wyoming subbituminous coal and describes an experiment in which 1 tonne of Wyoming coal is stored in a 5 metre long insulated container whilst air was passed through. Temperature rises, rates of oxygen absorption and gas compositions of the air stream were measured. The report relates the results of these-experiments to a theory of spontaneous heating developed by Stott and Quan which stresses the importance of the moisture content of the coal and the relationship between the heat necessary to evaporate this water to the heat available from coal oxidation. The work was carried out over a five month period and the emphasis is on demonstrating the effects of moisture transfer and confirming the theory of Stott and Quan.

Jan 1, 1980

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By F. E. Cash

The Holmes Safety Association was organized and named in honor of the late Dr. Joseph A. Holmes, first director of the United States Bureau of Mines. The association is a national organization and operates through local, sectional, or State chapters in mining, petroleum, and allied industries. The National Council of the Holmes Safety Association consists of representatives of State councils and local chapters, with the Director of the Bureau of Mines as president.

Jan 1, 1929

By R. D. Berkenkotter

Titanium and iron assays obtained from cores of three diamond-drill holes from the Cebolla Creek titaniferous iron deposit were evaluated by statistical techniques to obtain information concerning the mineral characteristics of the deposit and to make a preliminary determination of sampling requirements for the deposit. A range of sample volumes representing sizes from one-sixth NX core 2 feet in length through full NX core 10 feet in length were prepared by split-ting the NX core with a diamond saw and combining pulverized splits. Results indicate the existence of at least two statistical populations having different average grades of iron and titanium. Each has an assay frequency distribution that is not normal but is highly peaked (leptokurtic). Frequency distributions of assays from specific altered zones of the drill holes appear to be normally distributed. Increasing the cross-sectional area of the sample unit to change assay volume did not result in significant changes either in assay values or the resulting frequency distributions of assays. However, when assay volume is increased by increasing sample interval, the shape of the assay frequency distribution changes, and a normal distribution of assays is approached. Positive correlation exists between titanium and iron assays. The degree of correlation, although very significant, is too low to use for prediction purposes. Although the amount of data from three widely separated drill holes is not sufficient to establish an average grade for this large deposit, it indicates a range of expected assay values and provides some information for determining requirements of future sampling for evaluation purposes.

Jan 1, 1963

The Mine Safety and Health Administration (MSHA) defines an independent contractor as “any person, partnership, corporation, subsidiary of a cor-poration, firm, association or other organization that contracts to perform services or construction at a mine.” Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Sep 1, 2007

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By Lester G. Morrell

AGAIN in 1963, as in nearly every year since 1946, the Canadian mineral industry has established a new national record in value of mineral production. The 1963 estimated total value of $2,976 million is 5 percent higher than the 1962 value of $2,845 million.2 As in previous years, metals made up more than half the value of total production. For selected years since 1949 the category percentages and total value are as follows: [ ] Crude petroleum, Canada's most valuable mineral product, accounted for 21 percent of the total value of minerals in 1963. In descending order came nickel 12 percent, iron ore 10 percent, copper 10 percent, gold 5 percent, and uranium 5 percent. Asbestos accounted for 5 percent, sand and gravel 4 percent, and cement 4 percent. The complete list of Canada's mineral products includes more than 50 basic commodities.

Jan 1, 1964

By R. S. Dean

In addition to the normal work and that pertaining to strategic minerals, the Metallurgical Division has been made responsible for carrying on major investigations in the development of processes' for the treatment of low-grade domestic manganese ores that heretofore have failed to yield products suitable for the preparation of ferromanganese, an alloy essential to every ton of steel produced. These investigations are particularly important at this time because of their part in tucking this country self-sufficient with regard to manganese when the stock-piled ore becomes e exhausted and as foreign shipments of ferro-grade ore are cut off. The results indicate that there is a good probability of accomplishing this objective, while at the same time conservation may be promoted through the use of normally useless material from the large, low-grade ore deposits.

Jan 1, 1941

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

By H. A. Dierks

Implementation of the joint Federal-State control program established in 1955 to cope with the mine water problem in the Pennsylvania anthracite region is described in this report. The increasing severity of the water problem in the anthracite mines has necessitated major adjustments as this continuing program has progressed. Since 1941 the Federal Government has recognized the mine water problem as an important factor in the worsening economic condition of the anthracite region by initiating scientific and technologic investigations and establishing the Anthracite Flood-Prevention Section in the Bureau of Mines in 1948. On the basis of comprehensive investigations and studies, the results of which were published in numerous reports and bulletins, the Anthracite Mine Drainage Commission of the Commonwealth of Pennsylvania formulated a plan that served as a background for legislative action in 1955, resulting in Public Law 162, 84th Congress (Act of July 15, 1955 (69 Stat. 352; 30 U.S.C. 571-576)), for the Federal Government, and Act No. 82 of the General Assembly, July 7, 1955, for the Commonwealth of Pennsylvania. The report covers 29 mine flood control projects approved and executed in implementing the aforementioned legislative acts. Essential engineering and cost details for each project are given, together with an evaluation of the effect that the installed facilities have on alleviating the mine water problem as it concerns individual mines and the anthracite industry as a whole.

Jan 1, 1962