Search Documents

To determine the relative permeability of the soil a series of percolation tests were performed at the three locations of interest at Lanse, i.e., 3C, 03A and strip bank, and KA and KB at Kato. Soil cores were removed to 2, 8, 16, 24 and 32 inch depths with the thin wall sampler tube, each core separated from the next by about fifteen feet. Then two-foot-long thin-wall tubes were inserted into the 2, 8, and 16 inch deep holes and three-foot long tubes were inserted into the 24 and 36 inch deep holes. Each tube was tamped down about one inch further to assure a bottom seal; the tubes were filled with water and the rate of fall was measured. The test is similar to those done for septic tank percolation studies 6; but is not quantitatively related to Darcy's coefficient of hydraulic conductivity because the water can flow in three dimensions from the bottom of the tube. The measurements are dependent on the length of test, since the rate of fall is a function of the head. Therefore, it should be noted that the 24 and 32 inch deep tubes should give faster percolation rates because of the one foot greater head. At locations 03A and 3C the data show a sharp decrease in percolation at increasing depth, Table XV. However, the percolation at 03A and 32 inch depth is much higher than at 3C (0.2 vs. 0.01 inches/hour); the fragipan layer must be deeper at the 3C location since this area does experience a perched water table. On the strip bank the rates of falling head are randomly variable, appearing to be as much dependent on the particular location of insertion as on depth of placement. For example, water drained from the 16 inch tube as fast as it was added, probably into a sub-surface cavity or crevice. At Kato the tubes were more difficult to place because of interference of tree roots. For this reason 2 inch deep tubes were not inserted. These short tests at Kato were inconclusive, varying extensively when the tubes were moved. Field permeability tests were also performed in two (previously described) eight-inch diameter permeater tubes at Lanse and one at Kato. Because the soil is confined inside the tube, hydraulic conductivity can be calculated according to Darcy's flow equation. The high values reported in Table XVI experienced when the tubes were rewetted from a dry surface condition, enable us to conclude that infiltration is faster than the saturated permeability of the soil. In contrast to the falling head percolation tests, these permeability results do not show a high variation between locations.

Jan 1, 1972

By Joseph P. Flick, Kathleen M. Kowalski, Lynn L. Rethi, Roberta A. Calhoun

Many miners are involved in tasks at the mine site that are similar to those sub-tasks performed in general construction, maintenance and repair (CMR) type work activities. As a result, many of the injuries in the mining industry today can be traced to employees performing these CMR type work activities. Indeed, a recent analysis of a major aggregate company revealed that 65% of all injuries documented originated from performing such CMR activities. It is hypothesized that the number of injuries to miners performing construction, maintenance and repair (CMR) work activities on mine property may be reduced through improved training that focuses on better hazard recognition using the numerous visual and other cues that are available for evaluating workplace health and safety hazards. To this end, researchers at NIOSH’s Pittsburgh Research Laboratory have merged two proven methods of training miners to recognize hazards, stereoscopic (3-D) slides and the concept of degraded images, into this training program. Stereoscopic (3-D) slides have been shown in earlier NIOSH and U.S. Bureau of Mines research to be an effective training aid for improving the ability of miners to recognize various geologic and mining-induced irregularities that can cause groundfalls.3 They realistically portray the natural mine environment, and thus are an excellent training aid for teaching miners to recognize such visual cues. The degraded image concept, originally developed by the military and used for target detection training, describes scenes where the target is partially hidden by cloud cover, dust, rain, natural barriers, buildings, or other obstructions that can camouflage or confuse the target. Research had shown that flight observers who were trained with less than ideal (or degraded) pictures were more successful in subsequent identification of targets than those trained using ideal (or highlighted) pictures of targets. In order to investigate this concept for training miners to recognize hazards, NIOSH researchers developed a prototype hazard recognition training program using such mining scenes. A control program based on traditional highlighted mining scenes was also developed. Both programs were applied to subjects in a field experiment. Results indicated that miners trained with the degraded images did significantly better on a follow-up test of hazard recognition.4 This hazard recognition program teaches trainees to look for hazards in a more realistic manner than that of the control program. This specific training program for CMR activities involves using the degraded image concept and 3-D slides. The module is designed to educate workers on hazard identification techniques and safe work practices. It focuses on teaching miners techniques for recognizing visual (sight) cues, and then uses these cues to evaluate mining conditions. It should be stressed that other senses, such as sound can also play an important role in hazard detection.

Jan 1, 1999

By N. H. Coates

As part of a joint program of the U.S. Atomic Energy Commission and the Federal Bureau of Mines for using nuclear energy to supply process heat, the Bureau designed and constructed a pilot-scale simulated nuclear reactor system. Although workable components were developed,5 the simulated nuclear reactor could not be operated continuously at its design conditions of 2,500°F. and 250 p.s.i.g. because the refractory materials used for insulation deteriorated. Replacement of these materials with porous carbon permitted sustained operation at design conditions, and a 1,000-hour demonstration run was completed successfully. No serious operating difficulties developed during the test. Leakage of helium after 1,000 hours was only 3 to 4 std. c.f.h. Inspection after the run revealed no damage to any of the components. Including earlier runs during previous research5 the system has been operated about 4,000 hours, of which 1,120 hours have been at 2,500° F. or higher. The helium-recycle compressor performed satisfactorily with no main¬tenance whatever for 2,445 hours, with about 2,000 hours at 900° to 1,000° F.

Jan 1, 1961

By L. C. IlsLey

A specially recommended cable is a rubber-sheathed cable that has met the minimum performance requirements for cables as set forth in Schedule 20. The first in the series of recommended cables was listed September, 1930, by an ad- vance notice published as Information Circular 6375 which described the conditions under which the cable tests were made. Since that time six additional cables have met the test re- quirements and have been specially recommended. The complete list of specially recommended. cables is as follows: Specially recommended-cables Cable Symbol No. Hazacord No. 2 BM1 Stranding 19 x 7 Hazacord No. 3 BM2 do. Hazacord No. 4 BM3 do. Super-service No. 3 BM4 7 x 19 Super-service No. 2 Super-service No.. 4 BM5 do. BM6 do. Super-service No. 4 BM7 7x 7 Manufacturer Hazard Insulated Wire Works (division of the Okonite Co.) Do. Do. Rome Wire Company (division of the General Cable Corporation) Do. Do. Do. The cables listed were all twin (parallel duplex) cables having outer belts or cov- erings of approximately -inch high-grade rubber compound, and have the same general appear- ance and relative dimensions as the types of twin cables in general use. The cables were tested under conditions designed to show their approximate perform- ance under mine conditions. Only twin-type cables have met these test conditions. Although the recommended trailing cables are much better and safer for mine use than other cables and withstand being run over by a 7-ton car, they should not be considered as 100 per cent safe. The 7-ton car test represents the minimum limit requirement effective at present under Schedule 2-C, but the test car operates on a straight and level track, and thus does not represent the more severe conditions of mine use such as might result from uneven and curved tracks.

Mar 1, 1931

By Thomas O. Glover

Economic growth in Cameroon was restricted during 1987 owing to a decrease in oil prices during 1986 and the falling value of the U.S. dollar in 1987. The yearly budget reflected a significant drop in revenues and expenditures. Taxes on imports and some exports were increased to raise revenue. The shortage of revenue and the lack of liquidity had restricted the Government's operation and investment programs. External public debt reached an estimated $3.2 billion2 representing 20.8% of the estimated gross domestic product (GDP) of $12.3 billion. The Government operated at an 8.7% deficit in 1987. The GDP growth rate had fallen to 0.6% in 1987 and was projected to remain at that level in 1988. Economic planning was managed through a series of 5-year plans. The country was under the sixth 5-year plan, which would end in 1991. The plan stressed balanced development as one method to achieve the desired results. Sources of revenue for the year included direct and allied taxes (31.2%). customs collections (31.0%), and oil royalties (28.0%). The oil royalties in 1987 represented a larger part of the budget than in 1986. In January 1987, eight African oil exporting countries, including Cameroon, formed the African Petroleum Producers' Association (APPA). The eight countries represented about 80% of the total African oil production of 5.2 million barrels per day in 1987. Cameroon produced approximately 3% of total APPA oil production. Cameroon produced approximately 68.5 million barrels of crude oil in 1987, slightly less than that produced in 1986. Earnings also fell in 1987, not only from falling production, but also from declining oil prices and the fall in value of the U.S. dollar on world markets. Oil had been the main stimulus of Cameroon's growth throughout the past decade, and a key generator of export revenues and financial resources for the economy.

Jan 1, 1989

By Kenneth E. Hjelmstad

The U.S. Bureau of Mines (USBM) has developed an electromagnetic (EM) fire warning alarm sys-tem for underground mines. The system generates a magnetic field for through-the-earth signal trans-mission to microreceivers carried by individual miners. EM fields can induce electric currents in metallic conductors; if an EM transmitting antenna and an electric blasting cap array are too close, the field could induce a current in the blasting array and cause an unintentional initiation of the electric detonators. The USBM conducted tests that define the safe and unsafe regions for using electric detonators near the transmitting antenna of the warning alarm system. The minimum safe distance between a transmitting antenna and a blasting array is the distance where the induced electrical current in the blasting array is 50 mA, which is the safe current level specified in Federal mine safety regulations. Tests indicate that at transmitting power levels of 100-and 1,000-W, separation distances of 9 and 21 m, respectively, were required. These distances are small compared with the dimensions of a mine. Thus, the tests indicate that, with proper placement of the transmitting antenna, the warning system can be used safely in the proximity of blasting arrays.

Jan 1, 2010

By P. C. Good

The work reported here was undertaken by the Federal Bureau of Mines to investigate new methods of preparing high-purity metal. Tungsten hexachloride was prepared by direct chlorination of scrap tungsten metal and by treating tungstic oxide with carbon and chlorine. The resulting tungsten hexachloride was purified by distillation and reduced win: sodium, magnesium, or hydrogen. The metal prepared by these techniques was at very high purity after arc melting but of variable quality prior to arc meIting. Metal recovery ranged from about 40 to 90 percent of theoretical values, It was found possible to deposit a smooth, dense coating of high-purity tungsten on the inside of a heated tube by vapor-phase reduction of tungsten hexachloride at reduced pressure.

Jan 1, 1961

To quickly and reliably assess the stability (safety) of saturated and unsaturated tailings pond embankments. Approach Determine embankment geometry and soil properties, then use that data to obtain the safety factor of the embankment directly from one of a series of factor-of-safety charts.

Jan 1, 1982

By Maria I. De Rosa

This report analyzes mobile equipment fires for all U.S. surface and underground coal and metal/nonmetal mining categories by state and 2 year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from MSHA mine fire accident publications and verbal communications with mine personnel. The analyses will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the hazards associated with mobile equipment fires and will create a basis for future fire research programs.

Jan 1, 2004

By Launa G. Mallett, Charles Vaught

This report is intended to help mine safety trainers better prepare to teach the influx of new underground coal miners who are entering the industry. This is done by identifying two different approaches to instruction and discussing the ways they may affect how well prepared new hires are to deal with a dynamic and hazardous workplace. One approach is based on the use of a syllabus. Those using a syllabus are more likely to rely on lecturing or direct instruction. This is a good way to get across factual information, but does not provide a context within which miners can fit the discrete facts so that they form an integrated whole set of concepts, principles, and skills. The other approach is based on the use of a curriculum. Those using a curriculum may be more likely to help miners integrate concepts and skills that give them an overall picture of the complex mining environment and how they fit into the workplace. This will better prepare them for the decision-making and problem-solving activities that will help them work safely and productively

Jan 1, 2008

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993

By L. B. Berger

"Additions to List Published in Information Circular 7444 NEW APPROVALSThe following respiratory protective devices have been approved by the United States Department of the Interior, Bureau of Mines, since Information Circular 7444 was issued (March 1948):Gas Masks Approved Under Schedules 14, 14A, 14B) 11+D, and 14E Type N: Universal Gas MasksUniversal gas masks with filters that afford respiratory protection against smoke from ordinary fires and limited respiratory protection against dusts, fumes, mists, and fogs but do not afford respiratory protection against the toxic smokes of warfare.Willson WUG-Nl universal gas mask. Approval BM-1443, issued to Willson Products, Inc., May 25, 1948.Bullard universal as mask. Extension of approval BM-1443, issued to E. D. Bullard Co., January 12, 19 9.Supplied-air Respirators Approved Under Schedules 19 and 19A Type C: Air-line Respirators4. METCO air-line respirator. Extension of approval BM-1920, issued to Metallizing Engineering Co., Inc., December 8, 1948.Type CE: Abrasive Blasting Helmets, Hoods, or Masks9. M.S.A. abrasive mask. Approval BM-1920, issued to Mine Safety Appliances Co., April 30, 1948."

Apr 1, 1949

By Deborah A. Spotts

Researchers at the Bureau of Mines have developed a technique for re- generating chromic acid-sulfuric acid etching solutions used in metal surface treatment operations. The technique utilizes a diaphragm cell equipped with a cation-selective membrane to oxidize cr3+ to cr6+ at the anode and to remove copper, the major metallic contaminant, at the cathode. Normally, spent etchant is discarded after approximately 3 days of use. Using the electrolytic cell, the etchant can be used for a year without replacement, From data obtained from industrial-scale cells, the installation of a regeneration cell with a 1,000-gal catholyte- holding tank has been estimated to save at least $240 per day, The payback period for the investment is estimated to be about 10 mo or less. Because the magnitude of these cost savings will vary at different locations, several graphs are presented to aid in calculating payback for a specific site. Using these graphs and the capital costs presented in this study, the payback period can be determined for installing a regeneration cell with a 500- or a 1,000-gal catholyte-holding tank in an existing surface treatment plant.

Jan 1, 1983

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

By Thomas M. Barczak

Purchasing a new set of longwall shields requires a substantial investment. A poor shield design can lead to economic hardships, safety concerns for the mine workers, and closure of the mine. This paper addresses several key points that should be considered in the procurement process: (1) understanding your goals and the logic in selecting a higher capacity shield, (2) the importance of completing performance testing before production shield fabrication begins, (3) making sure performance testing is properly done, (4) measuring load(stress) development during performance testing, (5) testing a shield to failure, and (6) the value of buying extra shields. In addition, several challenges are proposed for consideration in future shield designs. These include (1) 100,000 life-cycle expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control by optimizing setting pressures, (4) lubricated link joint design concepts, (5) composite material applications to reduce shield weight, (6) incorporating periodic weighting predictive algorithms into the data-processing software, (7) advanced component load measurement on two to three specially instrumented shields to detect loading in the structural components, and (8) constant set leg cylinder design.

Jan 10, 2000

Develop a machine which can accurately simulate both the breathing and metabolic functions of a human being. The advantages of such a machine over a human being for testing of respiratory protective devices lie in its ability to quantify metabolic input, its repeatability, and the lack of a need to deal with the vagaries of human subjects. Breathing simulation has been widely achieved throughout the world but metabolic simulation has not. Approach Utilize the latest computer technology and place the complex portion of the system in software, leaving the mechanical portion as simple as possible. How It Works The concept for the automated breathing and metabolic simulator (ABMS) was developed through a research contract with the Pennsylvania State University. The ABMS utilizes a continuous removal/replacement concept to simulate metabolic functions, with breathing and metabolic functions being controlled by a computer. The mechanical portion of the machine is simple; the complexity of the system lies in its computer software which is not subject to maintenance problems.

Jan 1, 1987

Continuously monitor air-borne radon daughters that are a hazard to underground miners. Approach A beta detector continuously counts beta activity collected on a filter paper to allow calculation of exposure in working level units. How It Works At each Site a constant flow pump draws mine air through a fiberglass filter located in front of a beta detector (pancake type Geiger Mueller tube), Radioactive particles (products of the radon 222 gas emanating from the mine walls) collect on the filter and decay, releasing alpha and beta particles as well as gamma rays. A portion of the beta particles penetrate the Geiger tube window and create electrical pulses in the tube. These pulses are then amplified and sent by a coaxial type or shielded electrical cable to a central monitor located some distance from a working level detector. At the central monitor incoming Signals are amplified and fed into two channels, (See the block

Jan 1, 1979

By Charles Vaught, Belinda Sue Mills, Henry P. Cole, William J. Wiehagen

This study reports the results of a survey of organizations that used problem-solving simulation exercises to support mine health and safety training. The exercises are designed to teach judgment and decision-making skills within two broad domains: (1) how miners respond to mine emergencies (e.g., first aid, self-rescue, and escape) and (2) how miners integrate safety concepts within the context and performance of routine production work. The simulation exercises were distributed by the Mine Safety and Health Administration's National Mine Health and Safety Academy near Beckley, WV. The present study focused on those organizations that ordered the exercises from the Academy over a 2-year period (1995-96). Researchers assessed how the materials were used and trainer perceptions of the impact of these materials on annual mine health and safety training . A total of 147 organizations ordered the exercises over the 2-year period. Survey responses were obtained from 52 of these organizations. Sixty percent of the respondents rated the exercises as more useful than traditional instructional materials, 40% as equally useful, and 0% as less useful. Most trainers (79%) felt that the exercises help them to make better use of workers’ knowledge and experience during training. Many (71%)also reported that the simulations helped to improve the effectiveness of their instruction and promoted a problem-solving approach to their training. Fifty of the fifty-two respondents reported that they would like to have new simulations developed. A large majority showed a proactive interest in helping to develop and field test new exercises. Ninety-four percent of the trainers judged the exercises as a good value; 92% planned to order more simulations in the future. Based on this study, recommendations are offered for the continuation and expansion of simulation exercises as one method for occupational health and safety training.

Jan 1, 2001

To provide safer and more efficient mine operations by improving the operational performance of underground trolley line communication systems. Approach The dc trolley line provides a convenient means of In-mine communication since it can carry signals to each phone on the system whether the phones are in mine vehicles or in a fixed location such as that of a dispatcher. In many cases, however, the system does not perform satisfactorily. Short communication range, noise, and dead spots commonly interfere with effective communication. These problems are inherent with the trolley line, which was designed to transmit power and not communication Signals. As a power line, the trolley line is connected to rectifiers and feeds many loads such as motors, water pumps, track block lights, etc. Each of these devices represents a low impedance radio frequency (RF) shunt that seriously reduces carrier communication Signals. Performance is therefore often poor and can be improved only if the effects of the various shunts can be reduced. The Bureau of Mines has developed numerous methods applicable to either existing or planned phone systems which can improve communication range and reduce the shunting effects of the various loads.

Jan 1, 1983

Detemine the elastic properties and structural integrity of a rock mass in situ. Approach An acoustic device that transmits and receives high-frequency seismic waves between boreholes was designed, built, and field tested. How It Works The acoustic cross-borehole apparatus operates by sending a seismic wave from a transmitter in one borehole to a receiver in a second bore? hole which may be located as far as fifty feet away, depending on the wave transmission quality of the rock. By measuring the wave's travel time and the distance between boreholes, the acoustic velocity of the rock mass can be determined. Characteristics of the seismic wave arriving at the receiver (such as the wave velocity, amplitude, and frequency content) are related to the physical properties of the geologic media, as calcu-

Jan 1, 1982