Search Documents

By Alan Mayton, Bertrand Valero, Farid Amirouche

Handling of heavy vehicles such as tractors, trucks and buses require a large roll stiffness which causes large high accelerations at the seat level during impacts. To provide comfort and minimize the energy transfer from the chassis and the seat a pneumatic active seat suspension is proposed. An active seat suspension design and control algorithm under development at the University of Illinois at Chicago, UIC, is being developed and tested. Preliminary results are presented in this paper. The design of a passive suspension typically consists of optimizing the value of two parameters: the stiffness and the damping of the suspension. The general dynamic performance of the suspension is limited to the conditions under which these parameters were obtained. A change in the input conditions might lead to poor suspension and an amplification of the vibration transmitted to the body. The focus of this paper is a robust, semi-active suspension system with a variable controlled damping and using the body response an index measure to minimize the acceleration at the interface of the seat and operator. A summary of existing suspensions, such as MR and ER fluids, and spring loaded and dual valve shock absorbent will be discussed to highlight the need of a semi-active pneumatic suspension system design. Methods A model of the proposed suspension was developed in MATLB (Simulink) and different control strategies for the valve position in relation to the cylinder pressure tested. The effects of stiffening and softening resulting from pressure changes in the cylinder were examined. The vertical accelerations of the seat was computed for different control strategies and configurations of the suspension and compared to the response of a passive seat suspension. A lump -mass model was created to represent the human body including the head, the upper, middle and lower torso as well as the legs. The connective forces between body segments were modeled through modal analysis techniques from previous experiments at the Vehicle Technology Laboratory. ISO standards and absorbed power were used to evaluate the different configuration of the seat suspension system in relation to the dynamic response of the operator. Results Initial results of the semi-active suspension system show a significant reduction in the RMS value of the acceleration of the seat. A reduction of the total absorbed power by the operator is expected to provide an insight into the control strategies adapted in the active suspension.

Jan 6, 2006

By L. D. Schmidt, W. C. Schroeder, A. C. Fieldner

"INTRODUCTION The highly mechanized character of modern warfare makes steel the most vital raw material. The shortage of steel scrap in the United States is forcing the use of increased quantities of pig iron in steel manufacture, so that the rate of pig-iron output will continue to be the controlling factor in steel production. 5/ At the same time, the construction of new blast furnaces is limited both by time and the amount of strategic material available. Under such circumstances, every effort must be made to attain and then maintain maximum pig-iron output from the equipment now in use.When forcing a blast furnace to the ultimate in production the highest standards for quality and uniformity of the coke must be maintained. In view of these facts, the Bureau of Mines, in cooperation with the Office of the Solid Fuels Coordinator for War, is surveying the coke industry to study the various steps in producing coke of higher quality and greater uniformity. 6/ The engineers conducting the survey are visiting key men in coke-oven and blast-furnace organizations to determine, first, the major and most common problems in coke production and use; and, second, the best and quickest method for solving them. Various operators have made good progress in solving individual problems, and a Nation-wide exchange of information among them will make possible widespread adoption of the best practices. It is the purpose, of the survey and reports such as this preliminary one to facilitate such exchange of information. As an outgrowth of the survey, it was soon revealed that many operators could be helped by cooperation with various Government agencies, particularly to procure suitable coals, minor additions to equipment facilities, and tests on certain properties of coal or coke, or specific advice concerning the operation of various types of equipment. The machinery and organization necessary for securing this cooperation have been set up as a part of this work."

May 1, 1943

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade. By the late 1990s, longwall mine output accounted for 40 percent of all underground output in the U.S., and today longwall mines account for approximately 50 percent of coal produced underground in the United States. A 53 percent increase in average shift production rates has occurred over the last fifteen years. This increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust provides an ongoing challenge for coal mine operators. The National Institute for Occupational Safety and Health (NIOSH) has completed a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify dust generation from major sources on the longwall section and to determine the relative effectiveness of the different control technologies in use today. Substantial reductions in dust levels were realized at sampling locations on the face when compared longwall surveys conduct in the 1990?s. This paper summarizes the results from the underground dust surveys and discusses current longwall dust control technology and operating practices.

Jan 1, 2010

By N. Kyriazi

The U.S. Bureau of Mines subjected the CSE SR-lOO self-contained self-rescuer (SCSR) approved by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. The apparatus were heated to 710 C for 48 h, cooled to -450 C for 16 h, vibrated for 9 h, and dropped 1 m on each axis. A critical concern was internal damage to an apparatus, without any obvious external signs, that would cause it to malfunction or seriously degrade its performance. Carbon dioxide (C02) levels in apparatus with combined treatments were higher than in apparatus with individual treatments and untreated apparatus. The higher levels remained within safe limits, however. None of the treatments caused venting of the small oxygen cylinder that provides starter oxygen. Some bottles were found to be empty because of manufacturing defects in the burst disks. This problem was corrected in later models. The heat treatments did make the case ends more difficult to remove and the breathing bag sticky and subsequently more difficult to unfold. An apparatus that was dropped and vibrated had a broken desiccant bag that released some of its contents which compromised the seal of the relief valve. The case was dented from the drops. As with the first-generation self-rescuers, if there is visible damage to the case of the apparatus, the apparatus should be considered to be internally damaged and must be removed from service.

Jan 1, 1990

By Anthony E. Szczuka

Two facets of surface mining were studied: feasibility of using training simulators to increase productivity of haulage trucks, front-end loaders, and shovels; and improving the efficiency of dragline operations with a computer-aided analysis of dragline usage and the addition of an on-board operator display. Training costs per student were estimated based on current training practices. Training objectives were derived from task: analyses of haulage trucks, front-end loaders, and shovels. The cost effectiveness of training simulators was determined. A computer-aided analysis defined the critical performance parameters. An on-board operator's display is recommended to improve operator efficiency.

Jan 1, 1976

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By W. W. Adams

"The ninth yearly National Safety Competition covering the calendar year 1933, conducted by the United States Bureau of Mines, w participated in by 332 mines and quarries situated in 35 States. Enrollment represented as increase of 10 plants over 1932, and one addition was made to the number of States represented.The primary purpose of the United. States Bureau of Mines in conducting the contest is to promote safety in United States mineral industries. This purpose is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive recognition on a national scale for their achievement the purpose is accomplished indirectly through studies by the United States Bureau of Mines of the facts contained in the accident reports the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics which constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting, from industrial accidents.Bronze trophies, known as 'Sentinels of Safety', which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were presented to five companies in the contest of 1933, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or opencut mines. The trophies are awarded for 1 year and are then transferred to the winners of the succeeding year's contest.The trophy for bituincus-coal mines was won by a company in Wyoming. A company in Tennessee won the trophy for metal mining. In the nonmetal-mine group the trophy was again won by a company in New York. A quarry in Michigan won the trophy for the quarry-and-opencut-mine group. The trophy for anthracite mines remains in Pennsylvania, as all anthracite mines in the contest are in that State."

Jul 1, 1934

By Ren G. Dong, Dan E. Welcome

Instrumented handles or dynamometers are widely used to measure hand forces and/or the biodynamic response of hand-arm system. To study hand-transmitted vibration exposure, six generations of instrument handles were constructed or initially developed by researchers in ECTB/HELD/NIOSH. This presentation provided a summary of these handles. Their basic characteristics, limitations, and usefulness are described, which may help their appropriate applications and further improvements. Six Designs of Instrumented Handles Handle 1: The conceptual design is recommended in ISO 10819 (1996)1 for glove test. The grip force is measured by detecting bending strains on a measuring beam in the handle. A special handle fixture was designed to connect the handle to a shaker. Except the screws, the handle and fixture were made from aluminum. Handle 2: The design is based on the principle of shear strain measurement.2-3 Both grip and push forces can be measured simultaneously using this handle. This handle was directly designed for a simulated vibrating tool. Handle 3: This design is basically composed of a handle base, a measuring cap, and two charge-based sensors (Kistler 9212) sandwiched between the base and cap. The handle was also made from aluminum. The fixture for Handle 1 was also used with this handle. This generation of handle has three different handle diameters (30, 40, and 50mm).4 Handle 4: This design is an improvement from Handle 3. The handle fixture was totally redesigned and it was much stiffer than the previous one. The aluminum measuring cap was replaced with a magnesium cap. Handle 5: The basic structure of this handle is the same as that for Handle 3. However, the piezoelectric sensors were replaced with two strain gage based sensors (Interface SML-50). Handle 6: This handle includes two measuring caps, four piezoelectric sensors, and a handle centre base. The handle fixture was the same as that with Handle 4. Methods for Handle Examinations The static and dynamic characterizations were performed using the methods reported by Dong et al.5-6 Results and Discussion Handle 1: The static force measurement depended on the hand grip location on the handle. Its natural frequency was less than 200 Hz.5,6 Because the transmissibility of gloves may not vary significantly with the applied grip force, this handle may be acceptable for glove test. However, the force measurements with this handle may not be reliable. Handle 2: The static force measured with this handle was insensitive to the hand acting location. However, when the handle was vibrating, the force signals could be totally distorted. For this reason, it was not used for vibration studies.

Jan 6, 2006

As mining operations in the United States (US) have become more productive, controlling the dust exposure of mine workers has become more challenging. In response, US mining operations are applying basic controls at elevated levels and are looking to emerging control tech­nologies in an effort to better control airborne respirable dust levels. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducts research to develop and/or improve control technologies that reduce the respirable dust exposure of workers in underground coal mines. The goals of this research involve optimizing the use of water sprays and ventilating air, as well as, evaluating emerging control tech­nologies. An overview of dust controls typically utilized in underground US coal mines will be provided. An update on ongoing PRL research efforts that are evaluating new control technologies will also be presented.

Jan 1, 2008

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

By Albert E. Long

THIS GLOSSARY is published lay the Bureau of Mines as a contribution too the mining literature to fill a long-felt need for a compilation of the terms used by the diamond-drilling industry. The first step toward preparation of the glossary was taken in October 1955 when the Diamond Core Drill Manufacturers Association (DCDMA) proposed that the Bureau of Mines undertake the cons compilation and publication of a glossary of the terms used by the diamond-drilling industry. The work was authorized in July 1956, and a preliminary draft of the glossary was completed in may 1958. Copies of the draft were submitted for review to members of the DCDMA and appropriate personnel of the Bureau of Mines. The final draft, incorporating the many helpful suggestions of the reviewers representing both the diamond-drilling industry and the Bureau of Mines, was completed in March 1959.

Jan 1, 1960

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

By Michael J. Jorgensen, Anoop Polsani, Khurram S. Khan

Riveting operations in aircraft manufacturing involves the use of power tools for manually drilling holes for the rivets, power drills for the setting of the holes for the rivets, as well as rivet guns to drive and set the rivets. To close the rivet, the rivet is driven against a metallic bar commonly called a “bucking bar”. The bucking bars are typically held firmly to increase the quality of the riveting, as well as keep the bucking bar from “dancing” against the metal piece being riveted. Thus, employees in aircraft manufacturing involved in riveting are exposed to hand-arm vibration from several sources, and epidemiological evidence suggests that vibration-related musculoskeletal disorders are associated with long term exposure to riveting tasks in the aircraft manufacturing of aircraft.1,2 Recently, tungsten technology has been introduced into aircraft manufacturing for bucking bars, which are heavier than traditional steel bucking bars of the same size. Rivet guns with tungsten pistons instead of steel pistons have also recently been introduced with the objective of reducing vibration exposure to the riveter. The objective of this study was to assess vibration characteristics of steel and tungsten bucking bars and rivet guns to identify the combination that simultaneously reduced the combined exposure to both the “riveter” and “bucker”. Methods Vibration (10g tri-axial accelerometer, Biometrics S2-10G-MF Series 2) was measured from eight experienced employees using seven different rivet guns on size 6 rivets, with the same person bucking for all subjects. Vibration was also measured on two different bucking bars for these same eight subjects, with the same person driving the rivets using the various rivet guns. The rivet guns consisted of three E4 steel piston guns with different RPMs (Guns A-E4, B-E4, C-E4), an E4 vibration dampened rivet gun (Gun D-E4D), an E3 steel piston rivet gun (Gun E-E3) and an E3 and E4 tungsten piston rivet guns (Guns F-E3T and G-E4T). The bucking bars were made of 90% tungsten (1694g) and cold-rolled steel (843g), and were the same shape and size. A two-way repeated measures analysis of variance was performed on the vibration (mean frequency weighted resultant acceleration) on both the rivet gun side and the bucking bar side, and mean rankings were used to assess the vibration simultaneously for the rivet gun and bucking bars to investigate which combinations provided the lowest vibration exposure. Results Frequency weighted resultant acceleration was significantly lower on the E3 tungsten (F-E3T) rivet gun than the E4 steel piston (B-E4) and the E4 tungsten piston (G-E4T) rivet guns (Figure 1). When measuring vibration on the bucking bar, the E4 (A-E4) steel piston rivet gun resulted in lower vibration on the bucking bars than the E4 tungsten piston (G-E4T) and E4 vibration dampened (D-E4D) rivet guns (Figure 2). Additionally, use of tungsten bucking bars resulted in a 35% decrease in resultant frequency weighted acceleration than when using steel bucking bars.

Jan 6, 2006

By V. F. Parry, W. S. Landers, John B. Goodman

"INTRODUCTION The object of this investigation was to demonstrate a satisfactory method of storing slack subbituminous coal in open pits in a manner,that would minimize the cause of the physical deterioration and would have a practical application.The storage of coal by industrial plants is to their advantage, since an adequate operating supplying of fuel is available at all times as insurance against transportation delays, shortages, and strikes. Furthermore, it is possible to participate in low seasonal freight rates and mine costs by permitting the railroads to utilize idle equipment and by taking advantage of the off-peak production at the mines. For a number of years, one of the larger beet-sugar companies operating in the Rocky Mountain region has taken advantage of the lower prices and seasonal production of subbituminous slack coal during the summer months and purchased a large proportion of its requirements for the annual winter campaign. This company, operating sugar-refining plants in the 1943 campaign, used 256,613 tons of subbituminous coal. Of this quantity, 166,636 tons was purchased during the off-peak season and stored for use during the winter. It is the practice of this concern to place coal purchased through the months of January to October in underwater storage for use in the beet-sugar campaign, which lasts from October to as late as, January. The beet-sugar refining ""campaign"" period starts immediately after the beginning of the beet harvest and lasts 60 to 70 days."

Aug 1, 1946

By George S. Rice, F. B. LANEY, A. J. Lanza, Edwin Higgins

Under its organic act the Federal Bureau of Mines is directed to conduct investigations relating to the improvement of health conditions in the mineral industries. This report describes the lead and zino deposits and the mining methods employed in the sheet-ground area of the Joplin district, Missouri, and discusses the causes and the methods of abating rock dust in the mines, the chemical and physical characteristics of the dust, and the quantities present in mine air. Although the preliminary investigation included a number of the "soft-ground" mines, the writer spent the larger part of his time in the sheet-ground mines, for in them alone was siliceous dust found in appreciable quantities. Some results of the preliminary investigation have been published by the Bureau of Mines in Technical Paper 105.a The territory covered in t~lCpreliminary investigation, during the period between November 7 and December 6, 1914, embraced parts of Jasper, Lawrence, Newton, and Greene Counties, Mo., and outlying districts in Kansas and Oklahoma. The remainder of the field work, to which 84 days during the period from February 9 to July 19, 1915, were devoted, was confined to the sheet-ground mines, the most important of which are situated in the vicinity of Joplin, Webb City, Carterville, and other smaller near-by towns in Jasper County, Mo.

Jan 1, 1917

By R. Stefanko

In this report, the use of Penn State Ventilation Simulator (PSU/MVS) for planning and evaluating new coal mine ventilation systems is demonstrated. The simulator's application to evaluate the ventilation system of a coal mine currently under development is discussed. The ventilation system is evaluated for representing development of the mine at the end of 12, 24 and 36 months after mining has begun. The report describes the necessary steps of data input preparation, ventilation network development, analysis of results, modifications to the network, and methods to expand the computer program for networks larger than 550 branches.

Jan 1, 1977

By N. H. Darton

This report presents the results of an investigation begun by the Government in the summer of 1907, the investigation being started under the immediate supervision of Dr. J. A. Holmes and continued under him as director after it was transferred to the Bureau of Mines in 1910, the field studies being completed in the spring of 1912. The purpose of the investigation was to obtain information on the origin of the inflammable gases in coal and the conditions under which they occur. It was especially intended to ascertain whether there was any relation between the occurrence of gas and the structural or other geologic features of the coal beds. To this end many months were spent in mines and much time was devoted to the examination of mine maps, bore-hole records, and other data made available by the kindness of various coal companies. Two fields of work were selected-one in the northern anthracite basin of Pennsylvania, where the beds are considerably flexed, and the other in the southern part of the bituminous coal field of Illinois, where the beds lie nearly horizontal. In order to take advantage of results of previous investigations of the same general subject, an extended examination was made of reports of various investigators in Europe and America. A digest of the information obtained from these publications is included in the first part of this report, which constitutes an introduction to the discussion of the conditions governing the occurrence of inflammable gas in coal beds.

Jan 1, 1915

By J. R. Thoenen

[Before 1914 Germany held a virtual monopoly on the world supply of potash for fertilizer purposes. During the World War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-tine prisms stimulated interest in various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany mad other sources reduced prices to below pre-war levels, and, as a result, most of the domestic procedures ceased operations. This experience demonstrated that a domestic source of potash was necessary but that it must be of such a nature that it could compete in price with foreign sources. As a direct result the potash content of thick]

Jan 1, 1941

By Terry Muldoon

In conventional noncoal, room-and-pillar mining, the cutting machine is frequently a major source of airborne dust. Water is often used for dust control. An evaluation of typically used water systems during this program showed that they reduced dust levels by 60 to 70 percent over dry cutting when at least 0.5 gpm of water was applied. These systems, however, are only marginally effective in maintaining compliance levels and the added moisture causes operational problems. During the program, three additional dust control systems were designed, fabricated, and evaluated. The first, a hollow cutter bar, was designed to capture dust in the kerf at the cutting zone. The system was only marginally effective in reducing dust levels due to its lack of control of other sources. Large quantities of material captured by the system made it operationally questionable. The second, a machine mounted exhaust system, was extremely effective in capturing virtually all the dust generated in the heading. The captured dust was ducted out of the heading and exhausted downstream in the crosscut. Exhausting the dust without scrubbing, however, creates problems for personnel working downstream of the cutting machine. Successful application would require changes to the mine ventilation system and mining sequence. The third, foam, injected foam from an onboard generator through a channel to the cutting zone at the tip of the bar. Test results showed that foam, using 1/3 to 1/2 the total fluid quantity, was equally effective when compared to the mine's current water system.

Jan 1, 1983