Search Documents

By Maria I. De Rosa

Table 1 and figure 1 show the number of fires and fire injuries that occurred in underground metal/nonmetal and stone mines by state during 1990-2001. Table 1 also shows the injury risk rates, employees' working hours, and lost workdays. Overall, 65 fires occurred in 20 states; these include 2 fires and no injuries for contractors. Six of the fires caused nine injuries. The yearly average was 5.4 fires and 0.75 injury. Forty-one fires with 2 injuries occurred in metal mines, 14 fires with 7 injuries occurred in nonmetal mines, and 10 fires with no injuries occurred in stone mines. The underground mine fires required 25 mine rescue team interventions and 30 mine/section evacuations. The Ewhr value was 260 x 10° hr (Irr = 0.007), and the LWD value was 83. Idaho had the most fires (eight fires and no injuries), followed by Louisiana (seven fires and two injuries), Michigan (six fires and six injuries), and Missouri (six fires and no injuries). Of these states, Michigan had the highest injury risk rate value (Irr = 0.146). Table 2, partly illustrated in figure 2, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires during the six time periods show an increase during the fourth period followed by a sharp decrease during the fifth period and a sharp increase in the last period. The number of fire injuries show an increase followed by a decrease during most of the periods, accompanied by a decline in employees' working hours during most of the periods; an increase is seen during the third and fourth periods. The In values follow patterns similar to those shown by the injury values. Tables 3-8 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 3 shows the major variables related to fires for 1990-2001. Table 9 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Fred L. Bishop

This paper describing the methods employed in the purchasing and supply departments of the Miami Copper Co., Miami, Ariz., is one of a series being prepared for and published by the United States Bureau of Mines on office practice in mining operations. GENERAL DESCRIPTION The Miami Copper Co.'s plant is located about 1 mile from the town of Miami, in the Globe-Miami Mining District, Gila County, Ariz. The property consists of a complete mining plant, concentrator, high-pressure steam power plant, and many other attendant structures. In normal times the company employs about 1,500 men, and mines and mills about 6,000,000 tons of ore annually.

Jan 1, 1932

By Herbert R. Babitzke

The purpose of this investigation was to optimize the high-temperature properties of columbium and tantalum. Columbium and tantalum were combined with selected alloying elements to achieve solid solution and dispersion strengthening. Fifty-six alloys were evaluated to determine their formability, hardness, strength at elevated temperatures, and oxidation resistance. The following six alloys showed high-temperature strength: [Cb-15Hf-5W-2Zr-4Al-4Ti-2N Cb-15Hf -5W-5Zr Cb-15.3Ti-4.1Zr-13.7Hf Ta-20Hf-4Al Ta-30Hf-4Al Ta-20Hf-5W-4Al] At 1,200° C, the columbium alloys had strength values of 40,000 psi or greater, and the tantalum alloys had strength values from 50,000 to 58,000 psi. For a 2-hour test period at 1,000° C, weight gains of only 9 and 8 mg/cm2, respectively, were observed on oxidation testing of two alloys, Cb-15Hf-5W-2Zr-4Al-4Ti-2N and Ta-20Hf-5W-4Al.

Jan 1, 1968

By R. M. GRANTHAM, J. H. SOULE

C. R. Keyes, F. C. Schrader , F. A. Jones ( the first director of the New Mexico School of Mines , whose name was given the deposits ) , and N. H. Darton all described the Jones iron deposits within a decade after their discovery in 1902 . The earliest locations now on record were made in 1927. Interest in iron ores was revived during the second World War . Paul E. Pesonen , of the Bureau of Mines , reported on the deposits in December 1941 and proposed an extensive exploratory program . In March 1942 , the deposit was reported upon by C. H. Johnson , also of the Bureau of Mines , and a definite program of exploration was outlined .

Feb 1, 1947

By M. H. Chetrick

An important factor in the design and operation of a lignite-gasification plant is knowledge of the thermal requirements. These not only vary with different-size plants but also with the operating conditions for a plant of given capacity. Thermal data have been collected since 1945 from a commercial-scale lignite-gasification pilot plant operated by the Bureau of Mines at Grand Forks, N. Dak. The description and operation of this plant and a study of the gas-composition data have already been described in previous reports (1, 2, 3, 4, 5).2) / This investigation was made to review the thermal data taken in tests and to correlate them in terms of the fraction of undecomposed steam and the H2:CO ratio.

Jan 1, 1953

By William E. Dennis

"INTRODUCTION The San Antonio Canyon prospect was examined by engineers 3/ of the Bureau of Mines in March 1943 and again in October 1944. In July 1944, the United States Geological Survey mapped the prospect and submitted a report 4/ recommending core drilling by the Bureau of Mines. The drilling project, which was supervised by the author, was started on January 10 and completed on May 10, 1946.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests. Acknowledgment is made to W. D. McMillan, engineer in charge of the Austin field office, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, for general direction and advice. The samples were analysed in the laboratory of the Metallurgical Branch at Rolla, Mo., C. Travis Anderson, chief."

May 1, 1947

By G. S. Scott

It is sometimes desirable to know what changes in sizing characteristics would appear in screened coals if screens of different - size openings than those employed had been used . This report is concerned entirely with the application of the Rosin- Rammler law to a solution of this problem .

Dec 1, 1943

By James H. Russell

The Bureau of Mines used a statistical approach to evaluate the effects of temperature, current density, and composition of the electrolyte on the purity of boron prepared by electrolysis of a fused mixture of boric oxide in potassium fluoborate. The quadratic equation which best fits the data was calculated for a temperature of 650° to 850° C, a cathode current density of 40 to 1,150 amp/ft2,and a boric oxide content of 0.3 to 7.1 molal. The best products, better than 95 percent boron, were obtained when the current density was less than 2 amp/ft2 and the boric oxide content was less than 2 molal.

Jan 1, 1967

By L. A. Haas

The U.S. Department of the Interior, Bureau of Mines, is conducting laboratory-scale research to determine the leaching conditions required with sulfuric acid for extracting base metal from a matte with a copper-to-nicke1 ratio of 6 to 1. The matte (61.2 pct Cu, 9.7 pct Ni, 3.3 pct Fe, 21 pct S, and about 5 oz of precious metals per ton) was prepared from Duluth Complex (Minnesota) ore by smelting a bulk sulfide flotation concentrate. The matte was pre leached at atmospheric pressure to selectively extract 20 pct of the nickel, and the undissolved solids were referred to as the matte residue. Autoclave leaching of the matte residue extracted over 95 pct of the nickel, copper, and iron. The remaining leach residue in the autoclave contained over 100 oz of precious metals per ton. The leaching conditions required were matte grind of greater than 98 pct minus 325 mesh, pulp concentration of 50 g/1, total pressure of 100 psig with oxygen at 150° C or 400 psig with air at 180° C, 50 g/1 H2S04, 700 rpm agitator speed, and 6 hours of leaching time. The leaching time was decreased to 2 hours by increasing the agitator speed to 1,300 rpm. Sulfuric acid concentration greater than 50 g/1 did not appreciably enhance the base metal extraction, but with less acid, residues with higher iron concentrations were obtained. Supersaturation of the liquor was prevented at 150° C by using a 1ixiviant that contained 30 g/l Ni and 20 g/1 Cu.

Jan 1, 1979

By John L. Nieber

This information circular describes a computer program called VARSAT2D, a comprehensive unsaturated fluid flow simulator developed by the U.S. Bureau of Mines. VARSAT2D solves for either a vertical or horizontal, transient or steady-state solution in variably saturated, heterogeneous, anisotropic porous media using the Galerkin finite-element approach. Simplex triangular elements are used. Moisture retention characteristics are described by specifying either the Brooks and Corey, Brutsaert, or Van Genuchten power functions, with hysteresis described using the Maulem independent domain model. Boundary conditions may include any combination of time-varying seepage, pressure along solution domain, boundaries and/or at internal node points, unit hydraulic gradient at the lower boundary, and a uniform source and/or sink. This program should be a welcome addition for mining and environmental hydrologists, researchers, and engineers interested in modeling unsaturated fluid flow.

Jan 1, 1994

By Douglas F. Scott

Researchers from the U.S. Bureau of Mines conducted geologic investigations in an area of the Lucky Friday Mine, Mullan, ID, that included the 5300-107 demonstration stope using underhand longwall cut-and-fill mining. Structural analysis of the area suggested that argillite beds form planes of weakness between blocks of brittle quartzite, and energy may be released along these planes and at the junctures of fractures. Mapping argillite beds and fractures in the stope wall rock showed that the planes of these features diverged and that their attitudes corresponded from one wall to the other. Seismic analysis showed that the number and location of events varied as each cut was mined, with about 39 pct of the total number of events occurring above the cut being mined, about 54 pct below, and 7 pct at the same elevation.

Jan 1, 2010

By J. E. Schiller

The Bureau of Mines has investigated the surface charge of amphibole asbestos fibers and nonasbestiform cleavage fragments, as part of the Bureau's fundamental studies to provide new knowledge on the physical and chemical properties of the amphibole minerals. Microelectrophoresis was used to measure the electrophoretic mobilities, in water, of particles from six asbesti-from amphiboles and seven nonasbestiform amphiboles over the pH range of 5 through 9. The particles generally ranged in size from 2 to 5 µm wide by 10 to 30 µm long. The isoelectric point was determined for four of the minerals, and values were found to be between pH 3.5 and pH 5. The minerals studied had zeta potentials that generally ranged from -25 to -so mv in neutral solution. Attachment of colloidal positively charged AgI was also studied as a means of determining surface charge. Scanning electron microscopy of amphibole particles that had been in contact with aqueous AgI showed equal attachment of AgI to asbestos fibers and to cleavage fragments; the extent of AgI coating was the same for both. The electrophoretic mobilities of asbestos fibers were essentially the same as those of elongated cleavage fragments of the same aspect ratio (particle length divided by width). Blocky particles from both asbestiform and nonasbestiform specimens had lower mobilities.

Jan 1, 1980

By Foster Fraas

A comparison has been made between cubes and spheres in the matrix of the high-intensity wet magnetic separator. For two inclined plane surfaces, such as may occur with cubes, the maximum force value, H [dH-dx] is at the point of nearest approach and is much higher than the force resulting from adjacent spheres. Although the maximum force value for cubes is higher, it decreases more rapidly at increasing distances. The maximum force for spheres is at an appreciable distance from the point of nearest approach. At field intensities for magnetic saturation of the iron spheres, the force extends to further distances with greater uniformity approximating that of the constant force or isodynamic field. The force is also independent of the sphere diameter, which permits the scaling of the sphere diameter to provide changes in particle migration distances without changes in force gradient.

Jan 1, 1972

By Eric R. Bauer

This Bureau of Mines publication describes and illustrates the physical signs of excessive loading on mine roof supports, installations, and openings. It is designed to assist mine personnel in recognizing potentially hazardous ground conditions, by emphasizing the preliminary effects of developing unstable ground. Increased worker awareness can be expected to reduce the injuries and fatalities resulting from falls of roof, rib, and face.

Jan 1, 1985

By W. M. Deaton

The Keyes Helium Plant of the Federal Bureau of Mines was constructed under an expedited schedule, to supply the urgent and growing demand for helium in atomic energy, missiles, aerology, space exploration, shielded-arc welding, and low-temperature research. Construction began in December 1958 and ended in August 1959. The plant, near Keyes, Okla., processes 2 percent helium-bearing natural gas from the Keyes gasfield. In 1960 the plant produced and shipped 263 million cubic feet of helium (equivalent to an annual rate of 290 million cubic feet). Production cost was $9.11 a thousand cubic feet of helium. A low-temperature process involving two steps is used; the first separates a crude-helium product from the natural gas at about -250° F. and 225 pounds per square inch gage (p.s.i.g.); and the second purifies the crude helium to a high-purity product (Grade-A helium, 99.995 percent helium) at about -320° F. and 2,750 p.s.i.g.

Jan 1, 1961

By John Ward Smith, Neil B. Young

Shale specific - gravity to oil - yield relationships were developed for black shales of the New Albany Formation of Kentucky from data collected on core samples representing the complete section of the formation in three counties . Linear equations for estimating oil yield from measured specific gravity and for estimating specific gravity from measured oil yield were shown to be applicable within small error limits to all the sites tested . Variation in pyrite content is the largest source of error .

Jan 1, 1964

By P. C. Good

High-purity chromium was prepared in massive form by the electrolysis of chromium trioxide solution at high temperatures. The metal thus obtained, containing 50 to 150 p.p.m. of oxygen, 20 p.p.m. of nitrogen, and traces of metallic impurities, could be hot-worked to rod and sheet and drawn to wire ductile at room temperatures. Optimum concentrations and operating conditions were established for the deposition of chromium from chromic acid baths containing sulfate, fluoride, and silicofluoride ions. Current efficiencies of 13 percent were attained with baths containing sulfate ion, and efficiencies of 40 to 44 percent with baths containing fluoride and silicofluoride ions. Cation exchange resins were used for removing metallic impurities from chromic acid solutions containing sulfate ion; solutions containing fluoride and silicofluoride ions were purified by recrystallization.

Jan 1, 1960

By Jianmin Qin, Raja V. Ramani, Wilson Miola

"The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine.In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.Since the enactment of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Occupational Safety and Health Act of 1970, the prevalence of free silica as an occupational hazard in dusty work environments has been a matter of increasing concern. In underground coal mining, sometimes, roof, floor, clay veins and other non-coaly material must also be mined along with the coal. Mining these materials may increase the amount of quartz in the airborne dust (Pimentel and Adam, 1985; Taylor et al., 1984; Colinet et al., 1985). The problem of high quartz levels in the respirable airborne dust is widespread in continuous miner sections. In addition to the need for controlling the silica amount in mine atmosphere, a need for a sensitive, easily performed method for the determination of free silica in airborne dust samples was also recognized."

Mar 1, 1992

By R. V. Ramani, A. S. C. Owili-eger

? THIS PROGRAM SIMULATES METHANE FLOWRATES THROUGH THE GOAL ? SEAM BY THE GAUSS-SEIDEL ITERATIVE TECHNIQUE. THE MODEL IS A TWO ? DIMENSIONAL SYSTEM. THE ITERATIVE FORM OF THE GAUSS-SEIDEL IS ? OBTAINED FROM A PARTIAL DIFFERENTIAL EQUATION OF FLOW BY CENTRAL ? FINITE-DIFFERENCING APPROXIMATION SCHEME ? NPRESS IS THE NUMBER OF SPECIFIED PRESSURES EXCLUDING ? RESERVOIR AND FACE PRESSURES ? NQUAN IS THE NUMBER OF SPECIFIED FLOW QUANTITY.... EXCEPT FLOW ? OUT OF THE FACE. THIS- QUANTITY CAN BE POSITIVE(INJECTION) OR ? NEGATIVE ( PRODUCTION) ? XPERM(I,J) I S THE DIRECTIONAL PERMEABILITY IN THE X-DIRECTION AT THE POINT (I,J) ? YPERM(I,J) IS THE DIRECTIONAL PERMEABILITY IN THE Y-DIRECTION ? AT THE POINT (I,J) ? RESEP' IS THE RESERVOIR PRESSURE ? FACEP IS THE FACE PRESSURE. THIS PRESSURE IS ASSUMED TO BE ? APPROXIMATELY ATMOSPHERIC ? LENGTH, WIDTH, AND THICK ARE THE ZONE OR MEDIUM DIMENSIONS * PUHL I S A DUMMY NAME FOR VISCOSITY ? DMAXI IS VARIABLE NAME FOR INITIAL MAXIMUM ERROR OF ITERATION ? DMAXF IS A VARIABLE NAME FOR FINAL MAXIMUM ERROR OF ITERATION ? NITER IS A VARIABLE NAME FOR STORAGE OF NUMBER OF ITERATIONS ? RAD IS A VARIABLE NAME FOR THE SPECTRAL RADIUS OF THE GAUSS¬ ? SEIDEL MATRI-X. THIS PARAMETER ALSO MEASURES THE RATE OF ? CONVERGENCE OF THE ITERATION ? KOUNT IS AN ITERATION COUNTER ? MAXIT IS THE MAXIMUM NUMBER OF ITERATION SPECIFIED BY THE USER # EPS IS THE MAXIMUM RESIDUAL ALLOWABLE ERROR-FOR CONVERGENCE

Jan 1, 1974

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974