Search Documents

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By Carla A. Kertis

Because coalbed discontinuities often pose serious economic and safety problems in underground coal mines, criteria were documented for the recognition and prediction of discontinuities in advance of mining. Pennsylvanian strata in Indiana and Armstrong Counties, PA, were deposited as part of fluvio-deltaic complexes with channel-phase sandstones as the predominant type of coalbed discontinuity. Coalbed isopach maps constructed for this study delineated numerous want areas (areas of no coal) with elongate to linear geometries. A comparison of coalbed isopach and corresponding sandstone isolith maps of the study area revealed many examples of a thick-sandstone, thin-subjacent-coalbed relationship. Nearly 60 pct of the want areas in the study area were found to lie subjacent to thick (> 20 ft [6 m]) sandstone accumulations. In addition to erosion of the coalbed, channels may contribute to coalbed splitting, coalbed thinning over paleotopographic highs, abnormal coalbed thick- nesses, and deterioration of coal quality. If these features are considered, then approximately 80 pct of all interruptions in the economic coalbeds in this area result from channel activity. By using the criteria developed in this study and described in this Bureau of Mines report, the occurrence of coalbed discontinuities may be predicted and anticipated in advance of mining.

Jan 1, 1985

By D. D. Dornenburg

The effect of changes of atmospheric pressure on methane emissions from extensive worked-out areas of coal mines in several Midwestern States has lone caused concern to State and Federal mining departments, as well as to the operating companies involved. Common mining and ventilation methods employed in mines in these States have resulted in large sealed and unsealed worked-out areas in which considerable quantities of methane are emitted alone both intake-and return-air courses. The common practice is to watch barometric changes very closely and take special precautionary measurer during periods of low barometric pressure. Although the hazard is recognized, mining officials have different opinions concerning the effect of barometric pressure variations on the emission of mine gases. These opinions are based upon scattered personal observations, as no records exist of actual studies to establish such effects.

Jan 1, 1955

By Scott Turner

I have been asked to speak briefly about recent progress in the mining industry of the United States, and to touch on the general advancement of en- gineering science as applied to mining. By recent, I shall mean within the past 20 or 30 years. Such a period includes a great many of the changes which are of particular interest to the present generation of engineers, and the undergraduates of today will hardly turn back farther than the beginning of the present century in their study of develop- ment of methods and processes. Also, my own professional life spans this period, and I have seen or have been aware of most of these developments as they were taking place. In my review of developments, for the sake of simplicity and clarity, I shall deal separately with improvements in metal mining, coal mining, mechanical and electrical machinery for mines, metallurgy, petroleum engineering, and safety practices. Under each of these headings I have set down what appear to me to be the outstanding changes brought about during the past 2 or 3 decades. Other points will occur to other engineers; I do not represent that the following re- view is complete; it is only intended to be suggestive. In general, improvements in mining and metallurgical practices have come gradually, the charges being effected little by little, simultaneously in widely scattered places, and through the experience and inventive genius of many men. These changes have has small beginnings, and are generally the cumulative result of many steady and unsensational progressions, which still continue. What we today might be inclined to consider the culmination of a series of betterments in mining is, of course, but an instantaneous phase of developments which will continue in the future at even a more rapid pace than they have in the past. We are looking at but a flesh of a moving picture, with an endless reel to come after we finally leave the theatre. Behind all the changes in the mineral industry, the driving force has been the increasing demand of an expanding population for more metals and minerals with which to advance civilization. More people, with an increasing per capita consumption, together with the exhaustion of the richer but smaller, and more

Oct 1, 1930

By Daniel D. Sweeney

The United States coal mining industry has traditionally experienced difficulty in controlling dust levels below the occupational exposure limit. While improvements in face ventilation and water spray nozzles have decreased dust exposures, approximately eight percent of experienced coal miners are still developing Coal Worker?s Pneumoconiosis. This investigation tested the feasibility of enhancing existing engineering dust controls by mounting a simple barrier on a longwall shearer that separated the operators from the cutting drums. The barrier was constructed and tested above ground at the National Institute for Occupational Safety and Health Pittsburgh Research Laboratory longwall gallery test facility. A 96-percent reduction of respirable dust occurred at the headgate sampling position when tested at 2.4 m/sec (480 ft/min). The average dust level decreased from 39 mg/m3 to 1.5 mg/m3 by utilizing the barrier.

Jan 1, 2009

By Robert C. Ellman

The Bureau of Mines studied lignite pulverization in a laboratory ring-roller mill. Both moisture content and the source of lignite were found to be important factors in pulverizer operation. Reduction of moisture content increased capacity and reduced power consumption, but predrying is more effective than in-the-mill drying in improving pulverizer operation. A combination predrier-crusher system produced significant improvements but other efforts to improve in-the-mill drying in the test mill were unsuccessful. Pulverization of frozen lignite was found to seriously reduce pulverizer capacity and increase power requirements.

Jan 1, 1972

By Roy L. Soderberg

Ground support for metal, nonmetal, and coal mines was examined through fill placement with a pneumatic stower to increase extraction, reduce ground pressures, and improve general mine safety. Several pneumatically stowed stope-fill products were tested to determine the effects of specific gravity, gradation, moisture, and impact velocity on the in-place density of the stowed fill. Hydraulic sand filling has now served the mining industry for several decades but because of the low density does not always provide ample support to the hanging wall; therefore, the sill and crown pillars sometimes build up excessive stresses that are detrimental to mining. Cementation of a dense fill adjacent to a pillar to allow 100-pct extraction of the pillar, or a fill that can be placed without the use of water and where water is a detriment to rubber-tired mining equipment, was found to be a possible use of pneumatic fill. Placing of coal mine washery products into abandoned underground workings is another possibility in order to completely eliminate surface impoundments.

Jan 1, 1976

By W. W. Adams, T. D. Lawrence, D. R. White

"This paper presents the results of the eleventh yearly accident-prevention contest, the National Safety Competition of 1935, conducted by the United States Bureau of Mines. Participating in the competition were 336 mines and Quarries in 37 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies 'Sentinels of Safety.Since these annual contests were begun 11 years ago the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the pre¬vention of accidents has been achieved, as is indicated by an almost constant downward course in the accident-frequency rates for the contest group as a whole during the past 11 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the period and a downward trend during the latter part, except in 1930 and 1934, when two disastrous explosions occurred with heavy loss of life, and in 1935, when there was an increase in the number of fatalities although no major disasters occurred. The accident rate for 1935, both as to frequency and severity, was higher than for 1934.The National Safety Competition is conducted by the Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the fasts contained in the accident reports which the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics that constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting from industrial accidents."

Jul 1, 1936

Develop a portable emissions measurement apparatus to sample and measure tailpipe concentrations of diesel particulate matter (DPM), carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), and nitrogen dioxide (NO2) under steady-state engine load and speed conditions during a 1-minute test.

Jan 1, 1994

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By C. K. Man

Coal dust explosions are routinely conducted within the full-scale experimental mine at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM) to meet the needs of numerous safety and health research programs. Many of these explosion tests over the years involved igniting different coal dust and limestone rock dust mixtures (up to 80% by volume rock dust). Following four more recent tests, floor dust samples have been collected and analyzed using the alcohol coking test and scanning electron microscopy (SEM) and the results compared to estimate the flame travel.

Jan 1, 2009

By M. J. Brnich

The purpose of this U.S. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction delivered on either the Draeger OXY-SR60B or the CSE SR-100. Trainees' performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the donning task transferred.

Jan 1, 2010

By Marcia L. Harris

The National Institute for Occupational Safety and Health (NIOSH), as part of its continuing research program for evaluating coal dust explosion hazards, has investigated several areas in which current practices may need to be updated in order to adequately protect mines against coal dust propagated explosions. In the United States, current rock dusting requirements remained largely unchanged since 1969. US Title 30 Code of Federal Regulations Section 75.403 is based on a coal dust particle size survey performed in the 1920s and later was supplemented by full-scale testing of the rock dust ability to inert a coal dust explosion. NIOSH recently conducted a comprehensive survey of US underground coal mines to determine the range of coal particle sizes found in dust samples collected from the mine entries. Due to advancements in technology and modern coal mining techniques, the current coal dust particles in intake airways are significantly finer than those found in the mines in the 1920s. According to past full-scale dust explosion test results, the current rock dusting practices used in today?s mines to inert a coal dust explosion may not be adequate. Other closely related issues such as rock dust testing methods and sampling procedures are discussed.

Jan 1, 2009

By Robert Stefanko

Transients are results of sudden changes which take place in power systems and can be created by the opening and closing of switches and circuit breakers or the occurrence of a fault anywhere in the complex. Transients are of short duration, and the time during which they occur is an extremely small percentage of the total operating time. However, it is during these short periods that the greatest electrical stresses occur, mainly due to excessive currents or voltages. In extreme cases, system parts are damaged, and equipment failure follows. Safety can be further compromised because anomalous voltages can exist at machine frames. For several years, the electric utilities have been well aware of the serious nature of transients on their systems, but problems firmly believed to directly result from these phenomena are just now becoming apparent to the coal mining industry. The situation became discernible after the underground introduction of high voltage distribution systems (along with vacuum circuit breakers) and sensitive solid state electronic apparatus. In order to protect against such transients, knowledge about their characteristics and origin must be obtained.

Jan 1, 1974

By C. E. Augustine, P. Nicholls

"INTRODUCTION A layer of soot on the heating surface of a boiler decreases efficiency because it increases resistance to the flow of heat, with the result that the heat transfer to the water is lower and the temperature of the flue higher than they would be if the surface remained clean. The percentage of reduction in heat transfer depends on the position and area of the sooted. The percentage of reduction in heat transfer depends on the position and area of the sooted surfaces, the thickness of the most, until the percentage of the total heat absorbed by those surfaces when clean; thus it will vary with the type of boiler and in particular with the ratio of the area of the convection heating surface to the total area. Medium-size and large boilers usually are equipped with soot blowers, and tests have been published giving the increase in efficiency resulting from removal of the soot. Fuel savings up to,8 percent have been reported, but 4 to 5 percent is probably more conservatives. However, these savings may not be due wholly to a reduction the thermal resistance of the surfaces but may be due partly to improvement in the combustion because of better draft or more uniform flow of the gases. In addition, the deposits on the surface of boilers include as a clinker, and as the size of the boiler and the rate of burning increase very little or none will be soot.There are no corresponding test data on small boilers operated at low rates of burning. In stall boilers, deposits are much thicker, and it might be expected that the reduction in efficiency would be greater; in fact, statements have appeared suggesting that the decrease may be as high as 50 percent. This investigation was undertaken because the Bureau frequently receives requests for authoritative information on the effect of soot in small and other heating boilers."

Feb 1, 1935

By W. D. Walker

All pipelines used to transport liquid fuels over coal mines are potentially hazardous; however, this publication deals only with dangers in transporting gasoline. Since transporting gasoline by this method is an established practice, the hazards connected therewith should he recognized by coal-mine operators and pipeline companies so that every known precaution may be used to reduce and keep the hazards to a minimum. The purpose of this paper is to direct the attention of coal-mine operators and employees, pipeline-company officials, and other interested persons to the explosion and fire hazards that arise from seepage of gasoline into underground mines. A hazard is not only presented in an individual mine when gasoline enters underground workings; but, in cases where mines are interconnected, a hazard exists in mach such mine.

Jan 1, 1954

By W. E. Lamont

The Bureau of Mines conducted flotation tests on a mixture of barite waste materials from Nevada in which essentially all of the barite values were finer than 20 micrometers. Flotation variables investigated in these tests were the effects of (1) sodium silicate as a pulp dispersant, (2) sodium hydroxide as a pH modifier, (3) increased amounts of sodium cetyl sulfate, (4) conditioning time and (5) solids content during conditioning. The optimum flotation conditions were achieved by adding 2.5 pounds of sodium silicate and 10 pounds of sodium cetyl sulfate per ton of feed and conditioning the pulp for 20 minutes at a 35-percent solids content. Using these conditions, a concentrate was produced that contained 94.7 percent BaS04, with an attendant recovery of 90.9 percent of the barite in the feed. In addition to the flotation tests, a selective barite flocculation process was developed to treat extremely fine barite. A barite concentrate containing 96.5 percent BaS04 with an attendant recovery of 82.1 percent of the barite was produced by selective flocculation. A process patent application has been filed based on this process.

Jan 1, 1982

By William A. Beck

"The Piedmont Manganese Belt extends from Taliferro County, Georgia, 70 miles in a northeasterly direction through Greenwood County, South Carolina, and conforms with the trend of the Piedmont Province. The total area of the belt is reported to be about 1,000 square miles, and the maximum-width is about 24 miles.Manganese has been known to exist in the belt since 1845. M. Tuomey mentioned a deposit in the Edgefield district on Hard Labor Creek in South Carolina in a report on the geology of South Carolina published in 1848.Ore was first mined about the time of the first World War, when the Colley mine, near Lincolnton, Ga., was. Opened. The only operation in the area at present is that of the Abernathy & Kehaya Mining Co., at McCormick, S. C.The geographical position of the belt is from west longitude 82° 57’, north latitude 33° 39' to west longitude 82° 06', north latitude 34° 08'. The towns of Washington and Lincolnton, Ga., and McCormick and Greenwood, S. C., are in or near the belt.An exploratory project of the Bureau of Mines was started on the McCormick, S. C., deposit in April 1944, and trenching, test pitting, and hand-auger drilling-were done on a small scale until early in October 1944. (Fig. 1.) In November 1944 work was begun on a property 12 miles north of McCormick, known as Parsons Mountain, which is leased to M. H. McKnight by the United States Forest Service. From March 15 to March 24, 1945, work was done on the property of Mrs. H. B. Ross, which is known as the Morgan farm.The Abernathy & Kehaya manganese mine contains what is locally known as the Dorn gold mine; mineral rights on the property were owned by M. G. & J. J. Dorn, Inc."

Apr 1, 1946

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945