Search Documents

By Stephen Krickovic, J. E. Carpetta, T. D. Moore

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By Webster S. Anderson

Bureau of Mines planer mining tests on the phosphate bed of the Douglas mine, near Drummond, Mont., indicated that a competent bed with a Mohs' scale hardness of 3 to 4 cannot be mined economically with the planer. Although planer mining was feasible where the bed was fractured enough for a 4-inch depth of cut to be consistently maintained, the depth of cut in the competent beds at the Douglas mine did not exceed 0.5 inch. Average production rates were 0.15 ton per minute and 9 tons per man-shift.

Jan 1, 1966

By J. E. Tress

The Bureau of Mines has developed a process to utilize waste heat from electric arc steelmaking furnace gases to preheat the ferrous material charged to the furnace. Four heat exchangers were designed, tested, and operated successfully on 1-ton electric arc furnaces. Briquets and pellets were charged continuously, both countercurrent to the hot furnace offgasses and at ambient temperatures. A comparison of the electrical energy consumed in each situation showed that preheating can lower energy requirements as much as 15.6 percent.

Jan 1, 1975

By R. O. Pynnonen

This publication is an analysis of reports to the Bureau of Mines of 44 fatal accidents that occurred during the operation of rubber-tired, front-end loaders in the mineral industry. The causes of the accidents, the nature of the work being performed, and recommendations for preventing similar accidents are included.

Jan 1, 1967

By Albert E. Long

Since December 10, 1945, the Mount Weather Branch, Mining Division, Bureau of Mines, has been maintaining detailed performance and cost records on the diamond coring bits used throughout the United States by the Bureau of Mince. Figure 1 is a copy of a typical master record sheet showing the scope and type of information recorded for each bit. It is the intention of the Bureau of Mines to issue analytical reports covering the effects of diamond size and quality on the cost of core drilling in different rocks as the information on a significant number of bits used in any one type of rock is accumulated. This report is the first of such a proposed series and is based on the diamond loss and bit costs incurred in the use of 539 AX bits in coring operations on 10 different projects involving 6,097 feet of drilling in gneiss. The 10 projects were located in New York, Pennsylvania, and New Jersey (fig. 2). As a result of the information accumulated on the use of diamond-coring bits in drilling in gneiss, it has been found that the type of bit, the matrix, the percent of core recovered, and the size and quality of diamonds used have a definite effect on the cost of bits per foot drilled.

Jan 1, 1950

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

By L. B. Berger

This information circular is a revision of I.C. 7238, Danger from Carbon Monoxide in the Home, by L. B. Berger and H. H. Schrenk, issued in April 1943. Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the, dangers of this gas, and frequent news items report the finding of persons dead at unconscious from the effects of carbon monoxide, yet these accidents continue. Either these warnings are not read, or they are unheeded by people who feel that, "It can't happen to me." It can happen to you carbon monoxide is no respecter of persons.

Jan 1, 1954

By William E. Bruce

The Bureau of Mines performed drill calibration tests on two industrial percussive drills of 2-5/8- and 3-1/2-inch piston diameters to determine operating characteristics for their use in conjunction with penetration rate data in developing drillability equations and furthering the knowledge of percussive drills. The use of a linear velocity transducer for measuring piston velocities and application of its instrumentation are described. Data presented include relationships between maximum piston velocity and feed air pressure other results confirm the theory or data of previous investigators, and some comparisons are made with the performance prediction formulas of other investigators.

Jan 1, 1969

By Richard A. Watson, James A. Powell

A seismic system which utilizes in-mine geophones to detect trapped miners has been developed. Tests at the Bureau of Mines Safety Research Mine at Bruceton, Pa., and at two operating mines indicate such a system has a maximum detection range in excess of 1,000 feet. The system is field worthy and portable and requires less than 30 minutes to set up and check. Real-time detection is possible.

Jan 1, 1976

By K. E. Stanfield

Asphalts from. Wyoming "black oils" are being studied at the Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming. These black oils are characterized by their high-asphalt, high-sulphur, and low-gasoline content and are difficult to refine by present methods into high-octane motor fuels, burning oils, and lubricants. Accordingly, their principal use, at present, is for the manufacture of road oil and asphalt. The present production of black oil could be increased to meet a greater demand. During 1937 the daily production of these crude oils in Wyoming was slightly over 13,000 barrels, while, the estimated potential production from existing wells was 56,000 barrels.

Jan 1, 1939

By R. J. Heemstra

A continuous flowing paper electrophoresis cell was used to separate petroleum and petroleum extracts into characteristic patterns. The electrophoresis of Bachaquero, Lagunillas, Boscan, and Gibson petroleums in nitro-benzene and acetic acid-based electrolytes was investigated. The extent of separation in the patterns was studied by measuring the metal and porphyrin contents of the effluents. Qualitative separations were achieved in some systems, whereas either system demonstrated only a high degree of electrophoretic migration.

Jan 1, 1967

By C. W. Owings, L. D. Tracy

"IntroductionMany bituminous coal-mining companies have inaugurated extensive safety Programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania.Story of the ExplosionAt about 10 o'clock on the night of the explosion an examination was made in No 2 butt left and parallel off 7o. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of Po. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 18 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air an explosion occurred.The helper dropped to the floor and was burned about the face and wrists. The machine operator ran down the entry and was more severely burned about the face, neck, and arms. He later developed pneumonia and died. Both men reached the door in the chute between No. 14 and No. 15 north. A pumper, who had felt the rush of air, found the men and helped them to walk outside."

May 1, 1927

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974

By J. H. Bilbrey

A recording thermobalance ,vas used to determine the rates of oxidation of mol-ten tin over the temperature range 550°-900° C. Oxidation rates were found to vary widely for a given temperature, as previously reported by other investigators. 1 X-ray diffraction data indicated that the probable cause of these variations was the development of preferred orientations in the crystals forming the oxide film. No reasons for the differences in degree of preferred orientation were discovered. For relating the weight of the oxide formed (w) to the time of oxidation (t) an equation of the form wn = kt was found to best represent the experimental data. INTRODUCTION In the course of conducting investigations on the feasibility of using selective oxidation techniques for the purification of various metals in the molten state it was soon discovered that data on the oxidation of molten metals and alloys were very scarce. In contrast to the many hundreds of publications on the oxidation of metals in the solid state there are relatively few articles on the rates of molten-metal oxidation. In view of this scarcity of data, it was decided to institute a series of investigations into the oxidation processes of molten nonferrous metals and alloys with the expectation that the information derived could be put to practical use in developing and improving refining processes based on selective oxidation. This report is the first of a series in which oxidation data for molten nonferrous metals and alloys are presented.

Jan 1, 1955

By Robert J. Willard

This chapter includes tables from 1983 that were not available in time for publication of the 1983 Minerals Yearbook, but does not include corresponding tables for 1984. The value of raw nonfuel minerals produced in the United States during 1984 was estimated at $23.2 billion, an increase of $2.1 billion over the value for 1983. This is the second consecutive year that the value has increased, and except for a decrease in 1982, the value for each year has increased since 1971, or 12 out of 13 years. In 1984, 16 out of 21 metal commodities increased in output while 5 metals decreased; 14 metals increased in value and 7 decreased. Of 46 nonmetal commodities. 37 increased in output while 7 decreased and 2 remained unchanged; 35 nonmetals increased in value and 11 decreased. These statistics are grounds for continuing the cautious economic optimism expressed in 1983. Despite the note of optimism, however, numerous problems plague the mining industry, weakening its stability and inhibiting its growth potential. The problems are a complex mix of international and domestic factors that have been building in the recent past, but have become even more troublesome in 1984.

Jan 1, 1985

By W. C. McBee

Over the past several years the Bureau of Mines has developed a sulfur concrete (SC) technology in which chemically modified sulfur is mixed with suitable mineral aggregates to produce construction materials that are resistant to corrosion by acids and salts. Modified SC materials have been tested in actual operating conditions in 50 corrosive process environments at 40 commercial plants. SC components ranging from small test coupons to 4-ton acid sump tanks were fabricated and installed at plant locations where chemical corrosion was destroying conventional concrete materials. Through cooperative agreements with several companies, floors, retaining walls, and foundations were cast in place us-ing SC materials, then monitored for resistance to corrosion and retention of strength properties.

Jan 1, 1983

By Hugh Haddow

This paper describing the methods of recovery and treatment of a sand and gravel deposit and the preparation of these materials for a number of special markets is one of a series being prepared by the U. S. Bureau of Mines. It is of particular interest to those sand and gravel operators who have a surplus of fine sand which must be sent to waste, both from the point of view of, equipment and the variety. of markets supplied, and in that it describes one of the few sand and gravel plants which have resorted to hydraulic classification for sizing fine sand. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1931

By P. J. Colbassani

Samples of mine atmospheres collected by Federal coal-mine inspectors during their inspections and investigations of coal mines, in accordance with provisions of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U. S. C., sees. 451-483) are analyzed routinely by chemical methods at Bureau of Mines laboratories. When samples collected in open workings of nongassy coal mines at points not less than 12 inches from the roof, face, or rib contain 0.25 percent or more methane, the act requires the operator, during operation of such mine, to comply with the provisions of sec. 209, Title II, of the act, which pertain to gassy mines. The methane con-tents of such samples are determined by a physical method based on infrared absorption spectrometry to provide an independent check on analytical results obtained by chemical methods. This information circular describes the equipment and procedures used by the Bureau for determining low concentrations of methane in coal mine atmospheres by infrared absorption spectrometry. ACKNOWLEDGMENTS The authors are indebted to Dr. R. A. Friedel, Chief of Spectrometric Section, Branch of Coal-to-Oil Research, Bureau of Mines, for suggesting the analytical method and for furnishing valuable advice and assistance, and to J. A. Queiser of his staff for making exploratory measurements by this method; to Dr. M. G. Zabetakis of the Division of Explosives Technology for his assistance during the conduct of preliminary experimentation; and to L. B. Berger, Chief, Branch of Health Research, under whose guidance the equipment was procured and the work conducted.

Jan 1, 1958

By Donald P. Blasko

The first well that produced commercial quantities of oil in the Cook Inlet Basin of Alaska was completed in 1957. Since that time oil production in the basin has increased rapidly and by the end of 1969 had reached an annual rate of 74 million barrels. Five major oilfields had been developed, and two additional discoveries awaited development. Estimated amounts of recoverable oil by primary and secondary recovery methods total 2.7 billion barrels, or 36 percent of the estimated oil originally in place. Repressurization by injecting gas or water in formations containing undersaturated oil has significantly increased the volume of recoverable oil. All production has been from formations of the Tertiary age; that much of it is from depths of 10,000 feet or more is unusual for Tertiary formations. The oils are low in sulfur and contain low to moderate amounts of asphalt.

Jan 1, 1972