Search Documents

By H. D. Jacobs

The Federal Bureau of Mines, as part of a program to insure future raw material needs for the iron and steel industry, undertook research to beneficiate the oxidized taconites from the western Mesabi range in Minnesota. The data presented were obtained by applying the Bureau-developed selective-flocculation/cationic-flotation process to the second of three oxidized taconite samples. These three samples are representative of an estimated 10 billion tons of ore analyzing 30 to 40 pct iron. The experimental work was performed in a 900-lb/hr pilot plant. Treating the ore sample (36.1 pct Fe) with the Bureau's process produced commercially acceptable concentrates averaging 63.5 pct Fe and 4.3 pct SiO2, with an average iron recovery of 84.6 pct.

Jan 1, 1980

By H. R. Wells

The Blackbird district, Lemhi County, Idaho, has long been recognized as a potential source of cobalt and copper. However, the comparatively low grade and small size of the known ore bodies, the small demand for cobalt, and. the lack of adequate roads throughout the region precluded extensive exploration of the early discoveries in the area. Recent advances in alloy metallurgy, accentuated by wartime activities, greatly increased the demand for sources of domestic cobalt. Beginning In 1941, engineers of the Bureau of Mines conducted an examination and exploration program in the Blackbird district. This work was supplemented by an exploration program by engineers of the Howe Sound Mining Co., 730 Fifth Ave., New York 19, N.Y.

Jan 1, 1948

By D. R. Tesarik, M. K. Larson, D. K. Denton, J. B. Seymour, R. L. Rains, T. J. Williams

Because backfill has occasionally collapsed into an active working area, posing a hazard to miners, engineers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and Hecla Mining Co. installed instruments in a cemented, backfilled, stope-ramp intersection at Hecla’s Lucky Friday Mine, Mullan, ID. The purpose was to measure stress and strain changes in the backfill and reinforcing members during undercut mining. The instruments were monitored for 6 months while three successive cuts were mined below the intersection. Readings showed induced loads up to 3450 kPa (500 psi) in the backfill as stope walls converged 2.5 to 12 cm (1 to 5 in). The backfill then deformed against the top and bottom plates of the 2-m- (6-ft-) long vertical rock bolts installed as reinforcement, producing loads to 177 kN (40,000 lb)on the rock bolts. We hypothesize that a compressive zone was created in the backfill that allowed the backfill to remain stable as long as the compressive zones from adjacent rock bolts overlapped. This hypothesis is presented in graphical form. Of particular interest was the effect of loading on trusses installed to augment the vertical rock bolts and wire mesh typically installed in backfill. Data from the instruments indicate that wall closure perpendicular to the vein induced loads in truss legs parallel to the vein and in the rock bolt driven through the center of the truss, but, because they are designed to function under tension, truss legs perpendicular to the vein supplied in significant support as a result of compressional forces from wall closure. Based on this study, use of trusses was discontinued, and an alternative support system of wood beams and posts was installed as needed to ensure the safety of miners working beneath the backfill in stope-ramp intersections.

Jan 7, 2001

By K. C. Dean

Time and motion studies were made by the Federal Bureau of Mines on the hand and machine dismantling of scrapped auto starter motors, generators, and alternators for recovery of copper, aluminum, and iron. The studies showed that an individual with power handtools and convenient access to a hydraulic press, power bandsaw, acetylene torch, and power lathe could, in an 8-hour day, disassemble about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively, and the iron yield would be about seven times the copper weight. About 100 pounds of aluminum would be obtained from the alternators.

Jan 1, 1976

By R. R. Sayers

Radioactivity, the property of radium that led to its isolation more than 30 years ago, is the characteristic that makes it of value in the treatment of disease. Tyler3 gives the following brief history of the investigation: The way to the discovery of radium was opened in 1895 by Rontgen, who found that the glow from a Crooke's tube contained penetrating rays, which .he called X rays. Prof. Henri Bequerel, while investigating the effect of various phosphor¬ escent substances, found that uranium salts produced photographic impressions even when enveloped with opaque substances. To Marie Sklovouski, a young Polish student, who later became Madame Curie, Professor Bacquerel delegated the task of learning how and why uranium possessed power to emit these peculiar rays, which he had proved to be electrical in character. Madam Curie, examining by electri¬ cal methods the radioactivity of a large number of minerals containing uranium and thorium, discovered that some specimens of pitchblende had about four times the activity of the metal uranium; that chalcolite, the crystallized phosphate of copper and uranium, was twice as active as uranium; that autunite, a phosphate of calcium and uranium, was quite as active as the same weight of pure uranium. In order to check these discoveries, she prepared chalcolite artificially, starting with pure products, but found that this artificial chalcolite had only the acti¬ vity represented by its composition, or, roughly, 40 per cent of the activity of uranium. This led to the conclusion that there was some element or substance in the residue from uranium minerals that possesses a high degree of activity. After an exhaustive chemical investigation of pitchblende from Joachimsthal, she found that this mineral contained not only uranium but also another radioactive sub¬ stance, to which she gave the name of polonium, in honor of her native land. Later in 1898, Monsieur and Madame Curie found still another element, which, when brought to a state of concentration, was several million times as active as uranium, and to this was given the name of radium. Debierne afterwards found a fifth radio¬ active substance, actinium; and in 1906 Boltwood isolated the metal ionium. Strict¬ ly pure radium chloride was first produced in 1902. The first radium was produced commercially from the uranium residues obtained from the mines of Joachimsthal, Bohemia. Tyler calls to attention that, as the ores were a government monopoly, search was begun at once for sources in other parts of the world. As a result, radium-containing ores have been found in about 10 countries.

Oct 1, 1932

By McHenry Mosier

Diamond -drilling blast holes at Eastern Magnetite Mine C is proving economical in boundary shrinks , in removing pillars not readily accessible for percussion drilling , and in driving scraper drifts . The cost per foot drilled is greater than for percussion drilling , but savings in associated factors outweigh this handicap . The rocks drilled include trap rock and magnetite ore . The mining method is the panel , block- caving system utilizing scraper sublevel drifts instead of branch raises to convey the ore to the haulage level . Diamond -drilling blast holes was begun early in 1945. Three rigs equipped with noncoring bits are now in active operation two shifts per day . They are owned by the company , and the drill operators are paid by the day . In shrinkage stopes the drill is mounted on a horizontal bar set against opposite walls of the stope . Stoping holes are horizontal , which gives better results in blasting and requires fewer set ups . In scraper drifts the drill is mounted on a horizontal bar clamped to two columns about feet apart . Trim holes around the periphery of the drift and reliever holes are drilled 50 to 80 feet in length . A 10 - foot wedge cut drilled with a stoper is blasted in conjunction with a corresponding length of the trim holes to effect a 10 -foot advance of the full- sized drift . Recent drilling averages 97 feet per machine shift , excluding time utilized in setting up and moving the machine , hand mucking , and barring down . The feet drilled per bit at present is 417. These data represent the average for drilling in both rock (waste) and ore . Percussion drilling utilizes three types of wet drills . Detachable bits are standard . Gage changes for new bits is 1/8 inch and for reconditioned bits 1/16 inch . The life of a bit is five uses . Resharpening is on contract . A drill carriage is used in haulage headings .

Feb 1, 1948

By R. V. Ramani

This report is volume 1 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report contains a statement of the purpose and scope of work of the Grant, and provides an overview of the Master Design Simulator with a brief description of each subsystem. Also included is a discussion of several areas of application for the simulator.

Jan 1, 1975

By William Cochran

The Bureau of Mines investigated mine subsidence caused by recent underground mining, estimated the extent of damages, and formulated a procedure for evaluating subsidence costs. On the basis of the quantity of material removed from beneath the surface, bituminous coal mining currently causes more extensive subsidence problems than mining of other minerals; costs are highest in areas such as western Pennsylvania where urban and suburban development and related types of land use conflict with mineral recovery. The Bureau of Mines estimated subsidence costs, including surface damages and control costs, for a 12-county area in western Pennsylvania for 1968. Total surface damages attributable to the underground production of bituminous coal in the 1-year period were $295,000; in addition, 12.4 million tons of coal, valued at $4.3 million, was left in place to minimize potential surface damage. Of the total subsidence cost ($4.6 million), $2.7 million was classified as external or social costs, not reflected in the market value of bituminous coal; this averaged $0.05 per ton of production, or slightly less than 1 percent of the market value.

Jan 1, 1971

By W. M. Traver, A. M. Evans

"INTRODUCTION The Bureau of Mines undertook exploration in the Torlingua district, Texas, during June 1943, at a time when the demand for mercury for war industries was considerably more than the anticipated domestic production. In view of the impressive past production of the mines and the favorable geologic conditions in several underdeveloped areas in the district, the investigation was considered of immediate importance.Prior to initiation of the exploratory program, a preliminary examination of the district was made in August 1942 by A. B. Needham, an engineer of the Bureau of Mines. This examination was followed by a comprehensive geological study by the Federal Geological Survey 3/ and further investigation the Bureau of Mines."

Jan 1, 1947

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By David R. Flinn

This Bureau of Mines report describes methods to electrodeposit erosion-resistant titanium diboride coatings from molten alkali metal borate baths at 900° C. These coatings have been shown to be highly resistant to material loss during impingement with high-velocity alumina and silicon carbide powders, and they show promise as protective coatings to reduce metal loss in erosive chemical environments, such as coal gasification systems. The most erosion-resistant coatings were prepared on nickel, Inconel, and molybdenum from an electrolyte containing LiBO2, NaBO2, Na2Ti03, and TiO2. The best coatings were deposited at current densities of [~]20 ma/cm2, using titanium or titanium diboride anodes. Erosion-resistant coatings were shown to exhibit (1) a high degree of crystallographic orientation along the (100) or (110) planes, (2) a chromium impurity level of less than 3 pct, and (3) a uniform, smooth, consolidated surface appearance when viewed under a microscope or by scanning electron microscopy. Optical spectroscopic studies of the molten electrolyte suggest that the lower valent (+3) titanium ion predominates in the baths.

Jan 1, 1979

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

By Raja V. Ramani, Wilson Miola

"The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (ii) the amount of quartz in the samples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls arc necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples.In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.The current methods used for quartz analysis in powders are the P-7 infrared spectrometry and quantitative X-Ray Diffraction (XRD). Both have similar restrictions concerning the sample characteristics and operational problems, which arc intrinsic to radiation beams, device geometry, mechanics and controls of the radiation behavior. Although improvements can be made in the spectrometers and diffractometers, some of the most important steps are the procedures for analysis sample preparation from bulk samples and for calibration of the instruments. The sample preparation process is often referred to as one of grinding and sizing the bulk sample to generate the powder for the scanning devices. The particle sizes are referred to and their influence emphasized but the representativeness of the sample is assumed. Assuring sample representativeness during the sample preparation procedures is critical.For the sampling of airborne respirable dust in coal mines, the collection devices, the collection procedures and the analysis procedures are defined. This is not true for bulk samples where weights must be reduced thousands of times to generate the analysis samples for the scanning devices. The specifications to be developed may include bulk sample amount, sample reduction procedures, sample particle size distribution and sample amounts. However, the common problem of insufficient sample amount which is often encountered with mine airborne dust samples need not exist for bulk samples. Further, the same bulk sample can yield analysis samples for several experiments. The latter, of course, requires sample homogeneity.Three concepts are important in the selection of any procedure for sample preparation and analysis. These arc accuracy, reproducibility and representativeness. The adopted procedure has to guarantee a homogeneous sample representative of the population, a defined level of accuracy and reproducibility. Important statistical concepts are embedded in these requirements, particularly with respect to estimation and dispersion errors. Accuracy and reproducibility are totally different though not independent concepts. Estimation is related to accuracy and the true value. Dispersion is related to reproducibility and is measured by the classical statistical standard deviation of the distribution of a series of measurements or analysis performed over the same lot or analysis sample. The dispersion variance (or dispersion error) does not tell a"

Mar 1, 1992

By F. Chen, L. J. Gaydos, D. C. Kuhn, Demersm L. M., S. C. Sun

"Summary: In this report the differential regulation of NF-KB and nitric oxide (NO) was investigated in the mouse macrophage cell line RAW 264.7 following exposure to a mineral dust (silica) and /or an endotoxin (Lipopolysaccharide, LPS). The results indicated that silica and LPS can significantly induce the activation of NF-KB as well as elicit enhanced production of NO in RAW 264.7 cells as part of an early inflammatory response mechanism. A 24-hour time-course study showed that NO release from these cells continued to increase following the initial stimulus by LPS or silica. In contrast, activation of NF-KB was maximal at 6 hours and then showed a steady decline to 24 hours. The production of NO was suppressed by protease inhibitor and antioxidant, both of which block the activation of NF-KB. Surprisingly, the use of an NO synthase inhibitor resulted in an enhancement of NF-JCB activation. These findings suggest that NO produced in macrophage cells in response to an inflammatory stimulus like silica or LPS my be linked to a negative feedback role on the activation of NF-KB. It is now accepted that nitric oxide (NO) plays a pivotal role in the inflammation response process when macrophage cells are activated by a pro-inflammatory stimulus (l). Production of NO is dependent on the activity of the enzyme nitric oxide synthase (NOS). Up until now, at least three distinct genes have been described which encode different isoforms of NOS. NOS has been cloned from a variety of different mammalian cells, including constitutive neuron NOS, constitutive endothelium NOS and inducible NOS (2). Macrophages appear to be the principal cellular source for the inducible form of NOS (iNOS) activated in response to an inflammatory producing event. The mechanisms subserving the regulation of the iNOS gene and NO production have been under intense investigation in recent years (3-5). Several binding sites for transcriptional factors have been identified in the promoter region of iNOS gene, including NF-lCB, AP-1, NF-IL6, Oct-I to cite a few (5). NF-KB appears to play a"

Dec 1, 1996

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1954 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline. Data also are given for 30 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers I 1954 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 15 producers of aviation jet fuels are represented.

Jan 1, 1955

By Nan C. Jensen, Oliver Bowles

"INTRODUCTION Limestone (which consists essentially of calcium carbonate) and dolomite (calcium magnesium carbonate) occur widely in the United States. Their presence is of vast economic importance, because they are used much more extensively than any other form of rock. In 1945, limestone (which, broadly, includes dolomite) was quarried in every State except Delaware, New Hampshire, North Dakota, and Rhode Island, and also in Hawaii and Puerto Rico. Total production (including that used in cement and lime manufacture) exceeded 151,700,000 tons, or 79 percent of the quantity of all kinds of stone sold or used during that year.Important well-known uses of limestone are as concrete aggregate, road material, railroad ballast, for liming the land, for cement manufacture, as riprap for shore protection, harbor work, and spillways at dams, and as building stone.. None of these uses, however, are considered herein. The purpose of this paper is to discuss the industrial and chemical uses that are less widely known and yet are of tremendous importance in a great variety of processing industries. Important examples are dolomite as a refractory furnace lining and limestone as a fluxing agent in blast furnaces, and as a raw material employed in sugar, paper, glass, and alkali manufacture.PRIOR REPORTIn May 1941, the Bureau issued a report 4/ that described these uses in some detail. As new and important developments have taken place during the ensuing years, a revision and representation of the salient features of these uses seem desirable. Asphalt filler and mineral wool uses included in the earlier report are omitted from this paper because they are identified more closely with the highway and building industries, respectively, than with the industrial applications."

May 1, 1947

By James R. McVey

Tests during pillar robbing, longwall operations, and other mining activities indicate that roof-floor convergence rates can be used as an indicator of imminent roof failure. A large number of electrical-mechanical devices have been built to measure convergence as well as convergence rates, but most obstruct mine traffic and are costly and time consuming to install. The Bureau of Mines has designed and is evaluating three types of small ultrasonic units to make these measurements. The new instruments provide nonobstructing measurements up to 35 ft away. The ultrasonic transducers can be attached to a roof bolt, placed in an unsupported area (by means of a toss basket), or handheld. Total distance to the target and rate of closure are displayed digitally to 0.001 ft and 0.01 ft/min, respectively.

Jan 1, 1984

By Timothy M. Barton

The U.S. Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. A particular concern is ground control for deep-cover 1ongwalls located at depths in excess of 1,000 ft. The study described in this report was performed in two experimental sections in one longwall headgate section which contained three different pillar designs. Two of the designs used conventional abutment pillars, while the third was a total-yielding pillar system. Both of the test areas were located under 1,800 ft of cover. The purpose of this study was to evaluate the effectiveness of these three pillar designs for gate road stability. As the longwall mined passed the test areas, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The study indicated that the all-yield system performed nearly as well as the better of the two abutment pillar systems; but all of the three designs would have failed to provide acceptable stability for second panel mining without considerable artificial support.

Jan 1, 1989