Search Documents

By J. M. Kuchta

Concentrated hydrogen peroxide (H202) is a highly reactive oxidizing agent that liberates heat when it decomposes. The heat liberated may be sufficient to ignite combustibles with which the peroxide comes in contact. For this reason, concentrated hydrogen peroxide should be handled only by personnel familiar with its many unique properties.6 Hydrogen peroxide is used as a bleaching agent in the manufacture of textiles; this is its major single use in the United States. It is also employed as a reagent in chemical synthesis, as a source of free radicals to start polymerization, as a foaming agent in the manufacture of porous substances, and for its effect on biological processes. Moreover, highly concentrated hydrogen peroxide is a compact source of energy that can be utilized both as a monopropellant and as the oxidizer in a bipropellant system, During World War II, large quantities of highly concentrated hydro- gen peroxide were used as propellants, particularly in Germany. Since then, production of the peroxide has increased rapidly; in the United States alone it has more than doubled since 1950.7 Because of its widespread use, increasing interest has been shown in the hazards of handling the high- strength peroxide.

Jan 1, 1961

By J. B. F. Champlin

The continuing development of the nuclear industry in the United States requires a program of waste disposal that insures against the release of large amounts of radioactivity to the environment. This paper describes research on one proposed means of disposal of this waste, that of injection into geologic formations at depth. Nuclear production plant wastes were simulated and injected into samples of sedimentary rock obtained from outcrops, quarries, and deep wells. Changes in the chemical and physical characteristics of the rocks caused by the interaction of ions and suspended particles in the waste solutions with the cementing material and claylike particles in the rock are discussed. Laboratory tests show that nuclear wastes can be injected into many natural porous, permeable geologic formations. Injectivity can be maintained over a longer period by monitoring the ionic balance and particle-size distribution of waste streams. The combination of permeability and porosity with low cation-retention capacity, as exhibited by most sandstones, would satisfy the engineering requirements for the subsurface disposal of nuclear waste. Shales and clays with their low permeability and high cation-retention capacity would make excellent confining formations. The amount of cation retained by sedimentary rocks increases with increasing valence or concentration of the cation or decreasing brine concentration. The use of rock cores as model reservoirs had proved successful in determining some of the parameters that need to be considered in full-scale field disposal of wastes.

Jan 1, 1967

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

By S. M. Runke

An ever-increasing demand for beryllium and beryllium alloys has directed attention to the milling of low-grade domestic deposits as a possible means of supplying part of the Nation's ore requirements. The United States generally produces less than 10 percent of its annual supply. For example, new supply in 1953 was estimated at about 9,250 tons, of which the United States imported 8,500 tons. Domestic production was only 750 tons.2/ Since record high prices for beryl in 1952 and 1953 did not greatly increase domestic product ion, the United States must develop mechanical beneficiation processes to use low-grade deposits and reduce dependence on foreign sources

Jan 1, 1954

By John Ward Smith

Aragonite, co-occurring with calcite and dolomite as matrix minerals, has been discovered in Mahogany zone oil shales of Colorado's Eocene Green River Formation, posing puzzles on the geochemical patterns of their separate origins, reasons for their simultaneous existence, and their interrelation. The presence of aragonite is demonstrated by X-ray diffraction. Amounts of aragonite and dolomite are significantly and inversely related, but the calcite quantity is essentially independent of either aragonite or dolomite quantity. A geochemical pattern outlining the deposition conditions that created the Green River Formation oil shale is postulated from characteristics of the oil shale. The development of the three separate carbonates--aragonite, calcite, and dolomite--the inverse relationship between aragonite and dolomite, and the independence of amounts of calcite and the other two carbonates are shown to be natural consequences of this oil-shale genesis pattern.

Jan 1, 1973

By O. C. Blade

This survey report, the first for this type of fuel, is issued to provide information on the characteristics of the burner-fuel oils now manufactured for sale. Reports of surveys of diesel fuel, conducted under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines, United States Deportment of the Interior, have been published annually since 1950.2/ This survey of burner-fuel oils is similar to the diesel-fuel surveys In pattern and has been conducted under an extension of the same agreement at the request of the Oil-Heat Institute of America and the petroleum industry. It is not intended to conflict with the diesel-fuel survey but rather to supplement it. Burner-fuel oils, also specifically referred to as heating oil, range oil, furnace oil, "Bunker C," and fuel oil, are sold in increasing volumes for use in this country and for export. Sales of all grades of fuel oil in the United States have increased from 340 million barrels in 1926Y to over a billion barrels per year. 4/ Distillate fuel oil sales, in proportion to total fuel-oil volume sold, increased from 42 percent in 1950 to 50 percent in 1954. Sales of distillate and the heavier residual oils during recent years are shown: [ ] It must be realized that the data given are not accurate indications of the use of these materials as burner fuels. Some burner fuel, used as range oil, is kerosine, which is not included above. A large volume of fuel oil--approximately 30 percent of the distillate type and some residual fuel oil--is sold as diesel fuel. Smaller

Jan 1, 1955

By James R. Kerr

Although metallurgical benefits of processing metals in a vacuum or reduced atmosphere have been realized for a hundred years, the problem of creating a vacuum in the range from 10-0 to 10-4 mm. of mercury in a moderately sized furnace chamber has been difficult to solve. The demand for these and lower pressures, with the advent of World War II, for separating the fission-able uranium isotope from its stable twin by the electromagnetic process, gave impetus to developing pumps capable of delivering extremely low pressures. With the release of data by the Atomic Energy Commission on methods of securing high vacuum in large equipment, steel companies took the initiative, and the growth of the vacuum-melting industry was assured. Vacuum-induction melting of steel in the United States began on a small scale in early 1945 and in 10 years grew to 60,000 pounds per month or 720,000 pounds per year. The years following 1954 showed tremendous expansion, culminating in 1958 in a capacity of more than 36 million pounds.

Jan 1, 1962

By Rolland L. Blake

Petrographic methods of examination were used by the Bureau of Mines on a suite of samples of ultramafic rock from Soapstone Ridge, Ga., located about 8 miles south-southeast of Atlanta. The samples were analyzed to determine (1) their potential for releasing regulatory particles upon crushing and grinding and (2) their concentration of fibrous particles that approach the dimensions of amphibole and serpentine asbestos minerals. Such particles might be generated during grading and excavation for housing and industrial development and could become a health concern. Light optical microscopy, scanning electron microscopy, and X-ray diffraction were the techniques used to examine the samples. Six of the twelve samples contained amphibole as a major mineral; in five, it was a moderate to minor mineral. One sample contained no amphiboles, and serpentine was not observed or identified by X-ray diffraction in any of the samples. In nine of the samples, the amphiboles exhibited a habit that was either prismatic or acicular, but not asbestiform. Two of the samples did contain asbestos, occurring as small veins or fracture fillings, which represented only a minor percentage of the total sample. Similar petrographic screening is recommended for examining any rock deposit or mine location to delineate hazardous and nonhazardous mineral areas.

Jan 1, 1982

By William C. McBee

Specialized sulfur concretes were developed by the Federal Bureau of Mines as a result of research for the beneficial utilization of sulfur in construction materials. Materials were developed for use in acid and salt corrosive environments where portland cement concrete has been found to deteriorate. Because the mineral aggregates also come into contact with the corrosive media, concretes were developed utilizing both limestone and quartz aggregates. The sulfur binder used with both aggregates was modified by reaction with 5 pct dicyclopentadiene to improve product durability. Sulfur quartz aggregate concrete was found to have moderately high strength characteristics (6,000 psi compressive) and was extremely resistant to chemical attack by both acid and salt solutions. Sulfur limestone aggregate concrete exhibited very high strength characteristics (9,000 psi compressive) and was extremely resistant to chemical attack of salt solutions. Both types of concretes maintained their strength and integrity after long-term testing in acid and salt solutions and exhibited considerable resistance to damage by the action of freezing and thawing. Potential uses include leach tanks, electrolytic cells, thickeners, bridge decking, industrial flooring, pipe, and tile.

Jan 1, 1979

By P. R. Miles, J. K. H. Ma, J. Y. C. Ma, L. Bowman

"The bisbenzylisoquinoline alkaloids are compounds which can be isolated from plants and which exhibit a broad range of pharmacological activities. Perhaps the best known alkaloid of this group is tetrandrine (TT), a compound isolated from the root of a traditional Chinese medicinal herb, Stephania tetrandra. It has been tested for its effects on the cardiovascular system, tumors, and the lungs. For example, tetrandrine has been shown to act as a calcium entry blocker in cardiac sarcolemmal vesicles (King et a/., 1988) and has been used in China as a treatment for angina and hypertension. Its possible effects as a tumor-inhibitory substance have also been investigated (Kupchan and Atland, 1973). In addition, there are several lines of evidence to suggest that it is a possible therapeutic agent for the treatment of silicosis. Yu et a/. (1983) have shown that TT inhibits the development of experimental silicosis in rats when it is administered orally after intratracheal instillation of quartz. Other studies have shown that the alkaloid inhibits the synthesis of collagen by fibroblasts and the formation of silicotic nodules in rats exposed to silica (Huang et al., 1981; Liu et al., 1983). In fact, tetrandrine has been used clinically in China as an antifibrotic agent and has been shown to improve both the appearance of chest radiographs and the measurements of diffusing capacity in patients with silicosis (Li et al., 1981).Since tetrandrine may have a potential use as a therapeutic agent for fibrotic lung diseases, its effects on various pulmonary cells and tissues should be studied. Alveolar type II cells are located in the alveolar regions of the lungs and are important because they are responsible for the synthesis and secretion of pulmonary surfactant (Dobbs et al., 1982; King, 1984), regeneration of the alveolar epithelium after lung injury (Kauffman et al., 1974), and metabolism of foreign compounds (Bend et al., 1985). Furthermore, in silicosis, for which TT has been suggested as a treatment, there are increased amounts of pulmonary surfactant produced (Dethloff et al., 1986a,b) as a result of increased rates of surfactant synthesis by type II cells (Dethloff et a/., 1989; Miller et al., 1988). Because type II cells play a critical role in maintaining normal lung function and because type II cells are affected in silicosis, for which 'TT has been used as a treatment, we studied the effects of tetrandrine on energy metabolism in these cells in vitro. Energy metabolism was chosen because it is a basic cellular function which is neces-sary for other cellular processes to occur. Since type II cells depend on mitochondrial metabolism for energy production (Fisher et al., 1980), we examined the effects of tetrandrine on cellular and mitochondrial ATP production and oxygen consumption. Additional experiments were performed in an effort to determine if intracellular calcium levels may be involved in the TT-induced effects. A preliminary report of those results has appeared previously (Ma et al., 1991)."

Nov 1, 1995

By John Ward Smith

The potential economic value of oil shale depends on the products from thermal degradation of the rock, because no other practical method for producing valuable material from oil shale has been found. Detailed study of thermal degradation behavior can aid in characterizing oil shales and their deposits and in evaluating oil-shale processing methods, Numerous publications describe various pyrolysis properties of oil shales (see surveys 3, 9, 11 and articles 1, 2, 4-8, 10, 12),4 but they do not describe a generally applicable analytical procedure for detailed evaluation of thermal degradation products. The analytical method presented here for such evaluations is designed to provide for: 1. Control of retorting conditions--temperature, heating, rate, reaction atmosphere--plus some control over retort pressure and carrier-gas flow, 2. Precise direct gravimetric measurement of the thermal degradation products--oil, water, gas, and spent charge (residue after thermal treatment of the charge). 3. Samples of all products. 4. Determination of the identities and amounts of gaseous compounds produced. 5. Elemental analysis and gross heating value of all products. 6. Determination of the distribution in the retorting products of the elements present in the original samples.

Jan 1, 1962

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of lead and zinc from 104 domestic mines and deposits. Fourteen primary lead and fifty-three primary zinc operations with in situ demonstrated resources containing 27.3 million metric tons (t) of lead and 53 million t of zinc were subsequently evaluated. Potentially 17.5 million t of lead and 2.4 million t of byproduct zinc could be recovered from 14 primary lead operations. Economic evaluations performed in constant January 1982 dollars determined a long-run total cost per pound of recoverable commodity. Including a 15-pct discounted-cash-flow rate of return (DCFROR), 59 pct of primary lead was potentially available at or below $0.32 per pound of lead. Potentially 40 million t of zinc and 5.6 million t of byproduct lead could be recovered from 53 primary zinc operations. Ninety percent of the recoverable zinc is potentially available from currently nonproducing mines and deposits, and a weighted average of their long-run total costs was determined at $0.98 per pound of zinc. At a breakeven (0-pct) DCFROR, these non producing operations had a weighted average long-run total cost of $0.58 per pound of zinc. Sensitivity analyses illustrated that operations that recover byproducts were most sensitive to fluctuating metal prices, producing operations were more sensitive to increased smelter treatment charges, and nonproducing operations were impacted most by the DCFROR.

Jan 1, 1983

By J. A. Organiscak

The Bureau of Mines recently investigated dust generation and methane liberation during half-and full-web cutting at a double-drum shearer longwall face. This study was conducted to ascertain the health and safety aspects of wider web shearing at longwalls. Results from these underground tests showed that deeper web cutting reduced dust generation and methane liberation per ton of coal mined, while significantly improving shearer production rates. When cutting with the airflow (head-to-tail cut pass) full-web cutting decreased dust generation per ton by 16 pct at the shearer and 6 pct at the tailgate, with an increase in shearer production rate of 72 pct. Methane liberation per short ton also deere~sed by 36 pet at the shearer and 22 pct at the tailgate. Full-web cutting against the airflow (tail-to-head cut pass) decreased dust generation per ton by 41 pct at the shearer and 37 pct at the tail-gate over half-web cutting, with an increase in shearer production rate of 61 pct. Methane liberation per ton also decreased by 35 pct at the shearer and 41 pct at the tailgate. These improvements for full-web cutting are a reflection of improved cutting efficiency (less dust and methane produced from cutting) and less new face area exposed per ton of coal mined (less methane liberated from face per short ton of coal mined).

Jan 1, 1988

By C. Özgen Karacan

Longwall mining is an underground mining method during which a mechanical shearer progressively mines a large block of coal, called a panel, in an extensive area. During this operation the roof of the coal seam is supported only temporarily with hydraulic supports that protect the workers and the equipment on the coal face. As the coal is extracted, the supports automatically advance and the roof strata cave behind the supports. Caving results in fracturing and relaxation of the overlying strata, which is called "gob." Due its highly fractured nature, gob contains many flow paths for gas migration. Thus, if the overlying strata contain gassy sandstones or sandstone channels, gas shales or thinner coal seams which are not suitable for mining, then the mining-induced changes can cause unexpected or uncontrolled gas migration into the underground workplace. Vertical gob gas ventholes (GGV) are drilled into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important, first to understand the properties of the gas reservoir created by mining disturbances and, second, to optimize the well parameters and placement accordingly. In this paper, the production rate-pressure behaviors of six GGVs drilled over three adjacent panels were analyzed by using conventional multi-rate drawdown analysis techniques. The analyses were performed for infinite acting and pseudo-steady state flow models, which may be applicable during panel mining (DM) and after mining (AM) production periods of GGVs. These phases were analyzed separately since the reservoir properties, due to dynamic subsidence, boundary conditions and gas capacity of the gob reservoir may change between these two stages. The results suggest that conventional well test analysis techniques can be applicable to highly complex gob reservoirs and GGVs to determine parameters such as skin, permeability, radius of investigation, flow efficiency and damage ratio. The insights obtained from well test analyses can be used for a better understanding of the gob and for designing more effective gob gas venthole systems.

Jan 1, 2009

The strike of the Canadian asbestos miners entered its seventh month with increasing signs of early termination. Both unions are in the midst of heavy negotiations with management, and an optimistic industry source predicted that work would resume by October 1. Recession recovery in some segments of the asbestos manufacturing industry is being impeded by lack of fibers, CADMIUM - On September 9, St. Joe Minerals Corp. reduced the price of cadmium metal to $2.75 per pound. The producer price bad been uniformly quoted at $3.00 per pound since June 26, 1975. Subsequently, Amax, Inc. and National Zinc Co. reduced their prices to $2.50 per pound. By mid-September all five U.S. cadmium producers were marketing the metal at $2.50 per pound.

Jan 1, 1975

By L. D. Wyant

That natural gas-gasoline can be used to advantage as a refrigerant is suggested by the fact that the "make" tanks and other parts of the equipment of gasoline plants frequently become coated with frost. The experiments reported in this paper confirm this assumption and indicate that volatile gasoline can be use used to advantage in many refrigerating plants. The Bureau of Mines is making a study of wax distillates in order to find out why satisfactory lubricating oils and waxes can be made easily from certain crude oils and only with difficulty from others. In the commercial distillation of crude petroleum it is customary to separate the distillates into the following groups: (A) Gasolines and naphthas, (B) Kerosenes, (C) Gas oil, and (D) Wax distillate (consisting mostly of light lubricating oil together with small amounts of paraffin Wax).

Jan 1, 1923

By Frederick L. Hoffman

These extracts are sufficient for the purpose of emphasizing the practical difficulties of averaging iron-mining conditions so as to make general vital statistics concerning iron miners useful Tor scientific. purposes. It is self-evident that conclusions based upon iron miners, so called, working largely above ground and employed chiefly in open-cut blasting ~perations or the management of steam shovels, etc., can not be made to apply to miners working continuously underground with an exposure of dust and other conditions quite similar to underground mining methods in the extraction of gold, silver, copper, lead, and other ores. The so-called "milling" process as practiced on the Mesabi Range may here be referred to, the same being explained in the report of the Immigration Commission to consist "in the sinking of a shaft on the edge of the ore body from which a tunnel is run in under the ore and connected with a vertical, funnel-shaped hole from under the surface, through which the ore is 'milled' down into the tramcars placed under the opening under the tunnel. After being loaded at the bottom of the funnelshaped hole, the cars are run out to the bottom 0.£ the shaft. where the ore is dumped into skids or elevators and raised to the ~urface and unloaded into the tipple, where it is loaded into thecal'S ready for shipment." It is properly pointed out that the so-called " milling" process employs some of the features of both the open-pit and underground methods of mining. For these and many other reasons it is self-evident that general statistics concerning iron mining are quite likely to be inconclusive and possibly seriously misleading. Aside from the foregoing the problem is seriously complicated by the extensive employment of foreign labor in the iron-mining ind ustries of the Lake Superior districts and of Negro labor in iron mining in Alabama. Within recent years, according to the report of the Immigration Commission, a considerable displacement has occurred in t~e quality of labor employed in iron mining, the displacement bemg referred to as "progressive," in that one race or group of races has entered the region and taken up the work offered in the lower occupations, the race or races already holdinz such positions having. moved up in the scale of occupation leaving the field to the newcomers. This statement is quite suggestive in that it indicates a comparatively short average trade life or trade exposure, quite at variance with the relatively long average ascer- MINES, QUARRIES, ORE REDUCTION, AND SMELTING. 377 tained for the iron mines of New <Tersey. It is said in the report of the Immigration Commission that- The Scandinavians and the other northern European races have given way to the Finns and Slovenians, and in the open-pit mines the Finns and Slovenians have given way to the south Italian, Montenegrins, Croatins, and other southern European races. In the underground mines the common labor and mining is chiefly done bv Finns and Slovenians because the races from the southern countries can not stand the heavy physical work required in this kind of mining. Here, too, is found the same upward movement, for formerly the English (Cornishmen) and Scandinavians' were in the lower occupations in the underground properties, At present the south Italians, Serbians, Montenegrins, and Croatians are performing the most menial work and are the races who are now at the foot of the scale of occupations. It is a matter of conjecture on the ranges as to who will push these races up or whether they will remain the commou laborers of the region. Inquiry was made into the prevalence of diseases OIl the ranges, but more with reference to outside sanitary conditions than to occupational exposure. The most common diseases on the ranges, however, were ascertained to be pulmonary tuberculosis and typhoid fever, and to a lesser extent smallpox and venereal diseases. With -cgard to pulmonary tuberculosis it is said that the disease is most Eevalent among the Finns and the Swedes, and is chiefly imported, I'here is no reference to a possible connection between disease occur- ~ence and occupational conditions, above or below ground, but there .s no evidence that this aspect of the iron-mining industry was made .he subject of a special investigation.

Jan 1, 1918

By L. L. Oden

The Bureau of Mines has studied a number of processes to remove Cu from molten steel scrap with the objective of determining if any of the laboratory methods studied warranted in depth research investigations. Experimental approaches included oxidizing Cu from steel containing other metals that form stable mixed oxides with Cu (AI, Cr, Fe, Mn, Mo, and V), injecting the same metals as oxides to simplify the mechanism of complex oxide formation, partitioning Cu into alkali or alkaline earth silicate slags or oxide-moderated sulfides, and coremoving Cu and S by injecting active compounds of Ca and Mg. The most promising tests, producing nearly 0.3 pct Cu in the slag, used Ar injection of K20-moderated Na2S-FeS below the surface of molten steel containing about 0.6 pct Cu and protected by a CaO-SiOz slag; however, in depth research investigations currently are not felt to be warranted.

Jan 1, 1987

By Vincent Castranova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

"A group of bisbenzylisoouinoline alkaloids has been shown to exhibit various degrees of effectiveness in preventing silica-induced fibrosis in animal models [1, 2]. The objective the present study was to characterize the binding of several of these alkaloids to phosphatidylcholine vesicles and rat alveolar macrophages using fluorometric and equilibrium dialysis methods, respectively. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, chiral configurations, and double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is a highly effective agent in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, certain analogues of tetrandrine such as curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In conclusion, the results of these studies indicate that alveolar macrophages exhibit large binding capacities for certain members of this class of bisbenzylisoquinoline alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds. These data also suggest that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.INTRODUCTIONInhalation of crystalline silica is associated with the development of silicosis. This fibrotic disease is characterized by the appearance of concentric hyalinized nodular lesions in the lungs with the progressive development of pulmonary dysfunction [3, 4]. Many theories concerning the etiology of silicosis involve silica-induced activation of alveolar macrophages. Evidence indicates that in vitro silica exposures result in the generation of chemiluminescence, and the release of superoxide and hydrogen peroxide from alveolar macrophages [5]. Activation of alveolar macrophages has also been demonstrated after intratracheal instillation or inhalation of silica [5, 6]. Such excess release of reactive products from pulmonary phagocytes has been associated with damage to the lung parenchyma [7, 8]. In addition, silica exposure results in the release of mediators from alveolar macrophages, which enhance proliferation of fibroblasts and collagen synthesis by these pneumocytes [9-12]."

Mar 1, 1992