Search Documents

By G. B. Gait

This report is the third in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Lackawanna Basin of tile Northern anthracite field is presented. Previous reports IC 8274, published in 1965, and IC 8379, published in 1968, were catalogs of microfilmed maps of mines in the Eastern Middle anthracite field and Wyoming Basin, Northern anthracite field, respectively , Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1970

By R. D. Leitch

Spontaneous firing of coal during storage end even during shipment has long been a serious problem, especially in some regions and with some coals, and methods for preventing such firing have been investigated at intervals for more than 70 years. Spontaneous or other firing of coal waste, either outside or inside mines, has also been a problem probably for as long as mining has been practiced extensively. Much trouble has been caused by such fires, and much money has been spent in attempts to extinguish them. It is known generally that surface waste banks in bituminous-coal fields are very likely to take fire sooner or later, but it is not known so generally that anthracite refuse-bark fires also are common and that at least some of them are more serious in their effect and results than being regarded merely as a nuisance. There surface refuse fires probably would have attracted much more than local attention long ago had it not been that they usually cause no more serious trouble than air pollution. A few supposedly effective methods of preventing or extinguishing spontaneous fires have been reported rather recently. Unless one or more of these prove to be widely applicable, methods of solving these problems are no more certain today than they have been for many years.

Jan 1, 1940

By Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average Sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining.

Jan 1, 2010

The Waukon iron deposit comprises about 210 acres situated 2-1/2 miles north of Waukon, in Allamakee County, northeastern Iowa. The deposits have been exploited intermittently since 1899 and have produced about 67,000 tons of concentrated iron ore. From January to May 1943, the Bureau of Mines investigated the deposit to determine the extent of the ore-bearing material and its amenability to concentration, Seventy-one test pits were sunk. Those that indicated are of a grade high enough to warrant concentration tests were sampled. Average grade of ore was indicated to be 37.02 percent iron and 27.78 percent silica on a dry basis. Beneficiation tests indicated that the percentage of recovery might be relatively low.

Jan 1, 1949

By Florence L. Feicht, H. H. Schrenk, Carlton E. Brown

This report describes the dropping - mercury electrode , its use in analysis , and the procedure of the Health Division of the Bureau of Mines in determining lead , cadmium , and zinc . The dropping - mercury electrode or polarograph is an electrolytic device , one electrode of which consists of mercury issuing in small drops from a capillary tube . Such electrodes have been in existence for more than 50 years, but they were not used for analytical purposes until about 1922.6/ Developments since have been rapid , especially in Czechoslovakia , Germany , Italy, and Japan and more recently in the United States . A recent bibliography / contains references to, 825 articles issued from 1903 through 1940. In 1939 Kolthoff and Lingane presented the first comprehensive critical review, in English , of the device and its use in analysis . They have recently issued a book on the same subject. Similar information also is included in a recent book10/ by Kolthoff and Laitinen . Much of the information in this and the two following sections on this device and its use in analysis was obtained from these three publications . The use of the dropping - mercury electrode in analysis is based upon the fact that the kind and amount of electro - reducible and electro - oxidizable constituents in solution can be determined from the current -voltage relationships revealed by this electrode or electrolytic device .

May 1, 1942

By D. Harrington

The prevention of accidents to children from blasting cans is of vital importance not only to everyone using commercial explosives but to the country at large. The manufacturers of explosives have realized this danger for years and have attempted to publicize the hazards of allowing blasting caps to fall into the hands of children. Unfortunately, many of tie users of explosives have failed to realize the danger or have ignored their responsibilities in the matter. Investigations of accidents to children from blasting caps (and scores of them occur annually) reveal that most of them are caused by blasting caps picked up or made easily accessible to the victims. The children who are blinded, maimed for life, or killed are in large part the innocent victims of the carelessness, thoughtlessness, or negligence of their elders, by whom blasting caps are left lying about, carried in the pockets, dropped or lost around blasting operations, stored away and forgotten, or left in places where trey can be found or are accessible to children. Many such accidents occur to children under 12 years of age, when they are still curious or inquisitive. One of the first reactions of a child upon finding a blasting cap is to investigate and "see" how it is made or how it "works." A blasting cap in itself, with one end open, invites a child to poke it with a nail, piece of wire, or some other object to see what is inside; or he may attempt to break it open with a rock or hammer. A lighted match could be thrust into the open end, and there are numerous other approaches, may of which can result in serious accidents.

Jan 1, 1944

By E. Morrice

The metallurgical laboratory data developed in this study indicate an improved electrowinning process for producing higher purity cerium ingot. A typical sample of the Reno electrocerium contains 99.9 weight-percent cerium and the following impurities: Total other rare-earth elements, less than 0.04 percent; iron not detected; silicon and aluminum, less than 0.02 percent each; calcium plus magnesium, less than 0.01 percent; carbon, 0.01 percent; oxygen, 0.002 percent; hydrogen, 0.0003 percent; and nitrogen, 0.0015 percent.

Jan 1, 1960

By G. W. Marks, A. H. Roberson

"Previous investigation 4/ has demonstrated that some of the aliphatic amines are suitable absorbents for 302, This paper reports the results of physical studies of a number of such amines with the object of determining which is most favorable as an absorbent.Monoethanol amine, diethylene triamine, and triethylene tetramine appear to be the most promising of all the amines studied, and most of this report has been devoted to studies of the physical properties of their aqueous solutions, which contain varying amounts of SO2.PURITY OF MATERIALSAll of the amines used were of commercial grade, because the primary object of this research was the investigation of a proposed works process rather than the accumulation of scientific data.The aminoethyl derivitives of ethylene diamine, namely, diethylene triamine, triethylene tetramine, and tetraethylene pentamine, only recently have been produced commercially. The chemistry of aliphatic amines is complex, and these newer derivitives have not been investigated, completely. Chemically pure material is not on the market, and since definite physical standards have not been published, one could not be assured of a pure product even if the commercial material was refined.The compilation of physical constants for the pure amines would involve much time—consuming effort without materially enhancing the value of this paper, as this work was not devoted to the development of fundamental standards."

Oct 1, 1938

By Carlton E. Brown

[The purpose of this report is to present results of tests on the effectiveness of a spray of water mist, commonly called compressed-air water blast or water blast, in reducing the concentration of dust present in the air shortly after blasting and during mucking of the blasted material. Many observations have been male on the effectiveness of such ,sprays, but published quantitative information on comparative dust concentrations with and without their use, obtained by dust-sampling methods in use in this country, is rare if not absent. Tests conducted. in South Africa about 19164/ and more recently in England5/,6/ have shown that such sprays reduce the dust concentration to very low values within a fen minutes after blasting.]

Jan 1, 1938

By Margaret R. Lickes

Mercury was produced originally at the Idaho Almaden mine from 1939 to 1942. When the ;.nine was shut down, more than 100,000 tons of ore, containing from 2.5 to 3 pounds of mercury per ton, was known to be adjacent to old workings but had been considered too low grade for commercial operation. Later, detailed, systematic exploration by Rare Metals Corporation of America increased and delimited enough minable reserves for further operation to be foreseen for several years. The average grade of the ore is estimated at slightly more than 3.5 pounds of mercury per ton. Open-pit mining and installation of the largest rotary kiln in the United States furnacing mercury ore have made possible profitable exploitation of these reserves (fig. 1). The bulk of the exploration was by percussion drilling, although some diamond drilling was done to check the results. When enough reserves were indicated to assure a successful operation, stripping and plant construction were started simultaneously. Figure 2 is a general view of the plant. The ore bodies, although irregular in size, shape, and grade and covered by essentially barren cap rock, are amenable to low-cost, trackless, open-pit mining. Development consists of stripping the overburden and removing, barren cap rock. Ore is being mined at approximately [5],000 tons per month and treated in a 175-ton-per-day furnacing plant.

Jan 1, 1957

By C. C. Clark

This report presents the results of tests conducted by the U.S. Bureau of Mines to determine the transport characteristics of highly concentrated paste backfill mixes made from dewatered total mine tailings. The slurry concentrations of the mixes were all above 78 pct by weight with slumps ranging from 6.4 to 16.5 cm (2.5 to 6.5 in). Laboratory material property tests and full-scale pumping tests were conducted using pipe diameters of 102, 128, and 154 mm (4, 5, and 6 in) and a positive-displacement pump. The results indicated that the tested backfill mixes can be successfully transported as a stiff paste and identified the influence of and the interaction among the various mix and system variables.

Jan 1, 2010

By S. C. Termes

The Bureau of Mines has used Fourier transform infrared spectroscopy (FT-1R) to study in situ reactions of aqueous solutions of potassium ethylxanthate with CU(II)-and Pb(II)-activated sphalerite plates, in which the plates were both the infrared-transparent windows and the reacting surfaces. A copper (I) ethylxanthate formed predominantly with Cu(II)-activated sphalerite, regardless of the activation time. The products formed on Pb(II)-activated sphalerite depended on the activation times; a short activation time (30 min) yielded a lead ethylxanthate-like product, but a long activation time (90 min) yielded a considerable amount of dixanthogen.

Jan 1, 1986

By Frank E. Cash, Max S. Petersen

The use of safe equipment, safeguards, and safe practices in the mining and allied industries should reduce injuries and improve accident experience. The object of this report is to give to the mining industry, especially metal mining, a graphic pictorial description of some of the safeguards, equipment, and practices used and followed in the iron-ore mines of the Lake Superior district. Some of the subject material has been in use or has been established for many years, and some is relatively new. Some of the equipment was purchased commercially, and some was designed by the company employees and constructed in the mine shops. The photographs were taken by the personnel of the Health and Safety Division of the United States Bureau of Mines, primarily for use in the Metal-Mine Accident-Prevention Course of the Bureau of Mines. In general, they are arranged under the following headings or subjects: 1. Accident statistics. 2. Support of ground. 3. Hoisting and haulage. 4. Explosives. 5. Fires, gases, and ventilation.

Oct 1, 1948

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current mining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for dragline reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By R. A. Bloomfield

This report summarizes Bureau of Mines contract research on the disposal of retorted oil shale. A data base has been developed describing the physical-chemical properties, geotechnical engineering properties, and natural cementation characteristics of spent shale. Results of field compaction tests and seepage pond tests are presented, along with results of a partially saturated finite element seepage model used to predict infiltration and seepage rates. Preliminary engineering analyses are presented for underground disposal systems, which include material transport methods, and for a surface disposal system, which includes stability analyses.

Jan 1, 1981

By Boyd Guthrie

Methods of distilling topped crude oils and distillates under vacuum, accompanied by good fractionation, have taken a place of major importance in the refining industry. In the refining of petroleum products it is generally desirable to produce a distillate of good quality, and this objective is attained by fractionation of a high degree. The laboratory and commercial practice have proved that by varying the amount of fractionation the quality of the distillate can be changed, and refiners are cognizant of the advantages of good fractionation. Distillation under high vacuum, however, is a relatively new practice in petroleum refining, and only during the last few years has there been an indication that this method may become a general practice in the industry. Vacuum distillation offers many advantages over older methods of distilling petroleum products. Vacuum combined with steam distillation, for example, is replacing straight-steam distillation because the quality of the products of vacuum and steam distillation surpasses that of those produced by straight-steam distillation. Although the injection of varying amounts of steam in a vacuum unit is common practice, the amount of steam used is becoming loss as the vacuum within the unit is increased. This report describes the construction of a visible-action laboratory batch still and fractionating column and gives certain data pertaining to the operation of the apparatus under vacuum for the production of lubricating distillates. The apparatus was designed and built to produce lubricating distillates under as nearly ideal conditions as possible, in order that a subsequent study of the characteristics of the distillates could be made. For example, a study could be made of the distillates obtained up to the point of cracking of the charge if a topped crude were charged to the still; if the still was used as a rerun unit for lubricating distillates a study of nearly the entire charge could be made. Only topped crude has been charged to the still so far, and therefore this paper is limited to the results obtained from the distillation of such a charge. The results so far obtained indicate that such an apparatus is valuable in a study of different crude petroleums as sources of lubricating distillates.

Jan 1, 1932

By A. Visnapuu

The Bureau of Mines has upgraded high-iron domestic chromite concentrates by a carbonyl process. The upgraded chromite concentrates show as much as 10 wt pct higher Cr203 content and up to a threefold in-crease in the Cr:Fe ratio, compared with the starting concentrates. The high-iron chromites were first reduced to convert the iron oxides to the metal, and then treated with CO at elevated pressures and low temperatures to convert part of the metallic iron fraction to iron pentacarbonyl. Carbonylation was accelerated by the addition of H2S in small quantities. The iron pentacarbonyl was extricated from the con-centrate in the pressure reactor during carbonylation by a CO sweep through a pressure-reducing valve and passed through a decomposer at atmospheric pressure to convert it back to iron metal and CO. CO pres-sure, temperature, promoter trends, and other factors enhancing iron pentacarbonyl formation are presented.

Jan 1, 1985

By B. J. Moore

This Bureau of Mines publication contains analyses and related source data for 276 natural gas samples from 23 States. All samples except four were collected during calendar year 1984. Those four samples were collected earlier, but releases granting permission to publish were not received until 1984. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of these investigations are published annually to make the information available to the petroleum industry and the general public. Twenty-eight publications have presented the results of 13,957 gas analyses made prior to 1984. The first three bulletins (1-3)2 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26-28) containing 8,453 analyses of samples collected since 1960.

Jan 1, 1985

By C. J. H. Brest van Kempen

The objective of this contract was to provide thrust and torque control and visual output torque readout systems to an existing mine roof bolting machine and to test the consistency of torques obtained under actual field conditions. A Lee Norse TD1 roof bolter was modified by adding a simple torque sensing device to the drill rotation mechanism and a pneumatic logic control circuit that measures torque and controls the hydraulic circuit to the rotation motor. The modification controls and indicates the final installation torque of mine roof bolts. A total of over 5,000 mechanical roof bolts were installed in an operating coal mine. The installed torque of these bolts were within an error band (standard deviation) of 8%.

Jan 1, 1978

By Margaret E. Egan

Reliable fire detection is essential for both safe evacuation and containment or extinguishment. In order to increase reliability by reducing the number of nuisance fire alarms in underground mines that use diesel-powered equipment, the U.S. Bureau of Mines has developed a diesel-discriminating fire detector (DDD). It was designed to discriminate between smoke produced by a fire and the smoke-laden exhaust of a diesel engine. Experiments were conducted by the Bureau to compare the smoke detection capabilities of the DDD with those of conventional fire detectors in response to smoldering coal and conveyor belting. A comparison was made among the alarm times of a carbon monoxide (CO) detector with an alarm threshold of 5 ppm, a smoke detector with an optical density alarm threshold of 0.044 of', and the DDD with an alarm threshold of 0.025 V. The results show that the DDD will reliably detect developing coal and conveyor belt fires. The average time delay separating the DDD alarm from the first detector to alarm was 76 s for smoldering conveyor belt and 65 s for smoldering coal. The longest time delay between the response of the DDD and the first detector to alarm was approximately 120 s.

Jan 1, 1993