Search Documents

By Frank Parrish

History and performance data of 17 water-injection projects in Cooke and Grayson Counties in north Texas are presented for the purpose of studying and comparing operating practices and oil-recovery techniques. Water is injected into Strawn and Canyon sands of Pennsylvanian age. The principal formation flooded is the Strawn, which ranges in depth from 725 to 6,900 ft in the projects covered. Estimated ultimate recoveries range as follows: Primary, 22 to 494 bbl per acre ft; and secondary; 63 to 296 bbl per acre ft. These figures represent the following percentages of original oil in place: Primary, 10 to 46 pct; and secondary, 8 to 23 pct. Shallower projects; 725 to 1,500 ft in depth, had higher average primary and secondary recoveries than did deeper projects. Crude-oil gravity, which ranges from 20° to 45° API, was not relatable to yield of secondary recovery oil. Analysis of the data indicates that five-spot injection patterns will yield the highest percentage of oil remaining at start of flooding; that is, 28.8 pct for five-spot injection patterns, compared with 20.8 pct for line-drive patterns and 11.6 pct for random patterns. Waterflooding in this area appears to be very successful. Secondary recoveries of most projects are expected to nearly equal primary recoveries.

Jan 1, 1963

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs fur improving mine safety. One area of interest to the Bureau is new and improved means for minimizing the hazards of accidental gas ignition or electrical shock should the frame of an off-track machine assume potential above ground. Various means presently used to prevent such occurences are the use of ground fault detectors for phase to ground faults in ac machines, and grounding conductors and diodes in dc machines. In a three phase ac power center, a phase to ground fault may be detected by monitoring the current in the grounding resistor which is required between the power center neutral on the load side of the power center transformer and ground. Another method for detecting a ground fault is to pass the three load conductors through a toroidal core transformer. The phase currents vectorially add up to zero if none of the phases are faulted, and hence the voltage of the transformer secondary is either zero or not zero if one of the phases is unbalanced or faulted.

Jan 1, 1976

By D. K. Caddel

Several problems exist with the present design of coveralls used by miners in low coal (seam height 48 inches or less). The back portion of the coveralls often tears when roof bolts or rough areas in the roof are hit. Movement in the shoulder area is restricted. Female low coal miners find it difficult to purchase coveralls that fit properly, and must remove both their hard hat and safety belt in order to urinate and defecate. The objective of this research was to design coveralls which would alleviate these problems. The following features were incorporated into the coveralls; padding in the upper back area to avoid tearing, an action pleat in the shoulders to increase mobility, an inseam zipper to more easily allow miners to perform their bodily functions, and reflective tape to increase visibi¬lity of the miner. A heavyweight denim fabric was used to increase warmth and durability of the coveralls. The coveralls were assessed K long four parameters (comfort, safety, worker productivity, and fabric suitability) using both an in-field assessment by low coal miners and simulation studies. The experimental coveralls proved superior to conventional coveralls along all four parameters. Work clothing sizes for female miners were developed.

Jan 1, 1982

[ ]

Jan 1, 1979

By Felix A. Vogel

Rutile concentrate, used in the manufacture of welding rode, smoke-screen chemicals, and alloys, is being produced by the Titanium Alloy Co. of Arkansas at its mine and. mill in Magnet Cove. The company estimates a substantial reserve of recoverable rutile. This is a new operation, and production figures are not known. Previous operations had stripped the placer material, leaving the underlying mineralized zone. INTRODUCTION This report describes the mining and milling; operations of the Titanium Alloy Co. of Arkansas. The property was examined by the author on March 4, 1942, and subsequent dates. J. A. Wood, general manager, was very helpful in supplying information.

Jan 1, 1944

By Raymond M. Stateham

Infrared and displacement studies were made of an unsupported roof in Kaiser Steel Corp.'s York Canyon coal mine, Raton, N. Mex. Monitoring of the roof continued until the roof over the area was caved. Loose slabs in the roof, about 6 inches thick, were detected by means of associated thermal anomalies, using remote-sensing infrared instruments. Displacement measurements taken during the study indicate that roof movement was cyclic in nature; the cycles appear to have been related to the mine work cycle (work days to idle days).

Jan 1, 1974

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

By E. F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged mechanical dust collectors (scrubbers) with high dust collection efficiency and low energy comsumption for controlling dust in coal mining operations. All of the scrubbers described are similar in configuration and are powered by 6-hp, 2,000-ft3/min vane axial fans. Air pressure differential is less than 6 inches water column. Height of the scrubbers? including fan is less than 14 inches, width is less than 16 inches, and length is less than 45 inches. The flooded fibrous-bed scrubber achieved respirable (less than approximatey 7 µm) dust collection efficiencies of 95 percent. The small-diameter-cyclone scrubbers showed about 92 percent efficiency and can be best where excess water is a problem. The wetted brush scrubber showed 88 percent efficiency at low cost, and the wetted fan scrubber showed a slightly lower efficiency (87 percent) but offered the smallest size and cost. A suitable water droplet eliminator is described.

Jan 1, 1978

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

By S. J. Rodgers

This report presents guidelines on methods of dust control in conventional coal mining operations. The normal mining cycle and equipment used in a room and pillar conventional section are described. Main ventilation, section ventilation and face ventilation are discussed in detail. Proper installation of line brattice, maintenance of proper air flows at the face and split ventilation are stressed. The effects of maintaining the end of the line brattice near the face are described. The advantages and disadvantages of blowing and exhausting face ventilation are presented. The use of water sprays on cutter bars and loading machines is described. The design of a nonclogging water spray system developed under a Bureau of Mines contract is presented. Other methods of reducing dust exposure are discussed and include alternative procedures for shot firing and administrative controls.

Jan 1, 1983

By J. L. Holman

The Bureau of Mines has extended its previous development of cast Mn-Cu damping alloys to powder metallurgy (P/M) consolidation of alloys containing 55 to 75 wt-pct Mn. Blends of minus 200-mesh elemental powders were compacted cold in directional and isostatic presses. With 1 pct binder, typical green densities ranged between 76 and 80 pct of theoretical when pressing at 30 or 48 tsi. Green strength increased with compacting pressure and copper content. As-sintered tensile strengths ranged to 60,000 psi fox a hydrogen, sintered 60Mn-40Cu alloy, along with 5-pct elongation. Sintered densities ranged between 90 and 96 pct of theoretical. Sintering (a as effective when holding for 1 hr at maximum temperatures of 900° to 1,040` C, dependent on composition. Strength and ductility were considerably lower than for equiva¬lent cast alloys. When aged to the damping condition, alloys containing 60 to 70 pct Mn exhibited >40 pct specific damping capacity (SDC) at 5,000-psi stress, considerably higher than values reported for equivalent cast material. Effects of 1 or 3 pct Sn or Zn additions on SDC and other properties were assessed. Trials were conducted on consolidating rings and gears of the 65Mn-35Cu alloy on industrial-type P/M equipment.

Jan 1, 1979

By Albert H. Fay, Herbert M. Wilson

The national mine-safety demonstration at Pittsburgh, Pa., was projected and undertaken in the hope that it would aid the increase of safety in the mining industry. That the national mine-safety demonstration was warranted and has served a useful purpose was evidenced by the attendance, not only at the public demonstration in Forbes Field, but also at the more special exhibit of the work of the Bureau of Mines at the arsenal grounds and at the experimsntal. mine. Nearly 2,000 persons witnessed the demonstrations and exhibits of the Bureau of Mines at the arsenal grounds on the morning of October 30, 1911. The spectators were all mine operators, miners, or persons interested in mining, and represented operations in all parts of the United States. Nearly 1,200 of these persons visited the bureau's experimental mine at Bruceton to witness ~th~explosion of coal dust. Had the weather, which was exceptionally inclement, been more favorable, there would doubtless have been a much larger attendance. At the public demonstration in Forbes Field, which· was witnessed by President Taft, from 12,000 to 15,000 persons, chiefly mining men, were present and attested their interest and enthusiasm in the minesafety exhibits by remaining throughout the proceedings, regardless of the rain which fell all the morning .. Sincethis demonstration, the organization of first-aid corps and of rescue corps has been undertaken at mines where there had previously been no such organizations. The bureau has received letters of commendation attesting the value of the demonstration in drawing· attention to the dangers and to possible means of greater safety in mining. Many of these letters have urged that the results of the demonstration be published for the guidance and instruction of those who were present. In response to these reauests the following account of the mine- BlIIeLY demonstration lias been prepared. IIi its preparation various division and section chiefs of the Bureau of Mines have cooperated. The authors acknowledge the assistance they have received from those section chiefs and other members of the bureau who contributed detailed descriptions of apparatus exhibited at the demonstration or of investigations represented.

Jan 1, 1912

The condition of the domestic mining industry is obviously affected by the cycles in general business conditions. This study, the results of which are presented in a series of 78 charts, attempts to examine the interrelationships between the general business indicators and the major statistical measures for the base-metals industries during the cycles in the United States economy following World War II. For these industries the cyclical problem is perhaps less acute than the secular-trend problem. However, short-run fluctuations in production and employment do have very important impacts upon the welfare of the regions which derive a significant portion of their income from base-metals mining and processing industries. Any information concerning the normal patterns of development as the industries enter into a cyclical recession will permit better forecasts and perhaps help promote measures to alleviate the distress that occurs. Also, a systematic study of the comparative movements among the statistical measures during a series of cycles can bring to the fore the economic causation involved, and perhaps, after intensive study, can lead to a better method of short-range forecasting for these industries. This study has not fully achieved these aims. However, observations which significantly aid the interpretation of the current monthly statistics on these commodities are made, and some very general conclusions are drawn. The charts are presented so the interested people can examine them and draw additional conclusions. The charts refer specifically to cyclical analysis. The technique of indexing each cycle to its turning point effectively subordinates the longer term trend movements of the data. Thus, certain general conclusions flowing from this study and from the continuing economic research of the Office of Chief Economist will aid the reader by clarifying the frame of reference within which the charts should be examined.

Jan 1, 1961

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981

Reports by researchers in government, industry, and universities of the United States are given for various projects on basic coal research concerning, the metamorphism, physical and chemical properties, and reactions of coal, and how many of these studies can lead to better utilization of coal.

Jan 1, 1968

By R. H. Lien

The Bureau of Mines has conducted research on a flue gas desulfurization (FGD) process as part of its goal of minimizing the undesirable environmental impacts associated with sulfur dioxide (S02)-bearing waste gases. This FGD process, referred to as the modified citrate process, involves absorption of S02 in a buffered citric acid solution. The absorbed S02 is subsequently stripped from the solution using steam, which regenerates the solution and produces a wet S02 product. This product can be further processed to make sulfuric acid or liquid S02. Economic evaluations showed the process to be expensive when the stripper was operated at or near ambient pressures because of the large amounts of steam required for solution regeneration. Research was directed at reducing steam consumption in the stripper. The effect of stripper pressure on steam consumption was investigated. A process research unit (PRU) was operated with the stripper pressurized in the range of 5 to 150 psig. Test results showed that steam consumption decreased with increased stripper pressure. For example, when operating the PRU stripper at 150 psig, 4.1 grams of steam per gram of S02 was required to remove 90 pct of the S02 from a 1.0-vol-pct-S02 gas. This compares to 7.1 grams of steam per gram of S02 required for 90-pct S02 recovery at 5 psig.

Jan 1, 1982

By G. Andrews

This case study details the process that was used for project planning and permitting for the Greens Creek Mine, located near Juneau Alaska, as seen through the eyes of one of the primary environmental consultants. This case shows how a Company could involve the public and the agencies in the early 1980's and develop a project sensitive to concerns expressed with a high level of environmental protection. Comparisons are made to the current environmental permitting situation. Initial baseline studies performed during the exploration phase provided helpful information for more detailed environmental work in 1980-1981 as planning and permitting formally got underway. Since the mine was in a National Monument and abuts up to a designated wilderness, the Monument Manager administered the project for the lead agency, the USDA Forest Service. Planning and permitting progressed smoothly to a Final Environmental Impact Statement (FEIS) in 1983. Metal prices were depressed when the FEIS was completed and the project permitting proceeded slowly. Ownership changed several times in the mid-1980's. New owners re-evaluated the project and suggested five changes that required a supplemental EA prior to development. The project was fully permitted and started construction in 1988. Operation began in 1989. Today the environmental process in southeast Alaska is now much more complex, detailed, expensive, and time consuming than in the early 1980's. Significant issues discussed that may impede development and operation include overlapping agency jurisdictions, personal agendas of agency staff, conflicts between agencies that impede project progress, changing regulations, and a well organized environmental opposition.

Jan 1, 1993