Search Documents

By G. A. Wancheck

Shear tests were performed on several prepared samples of granular and powdery bulk materials to investigate the following parameters: Particle size and distribution, particle movement, moisture content, consolidation of material, bulk density, void ratio, porosity, volume change, and strain rate. A series of shear tests was performed with weight-percent-ratios of minus 0.185-inch tertiary sand and 1-1/2-by l/2-inch tertiary gravel mixtures, and weight-percent-ratios of minus 200-mesh limestone (rock dust) and minus 200-mesh bituminous float coal dust. A comparison was made for shear test results obtained with rectangular and circular shear cells utilizing the large and small direct shear testers. Specifically, the shear results obtained include the angle of internal friction or shear strength of the tested material under known consolidating pressures, and the kinematic angle of friction or coefficient of friction between the interface of a bulk material and a sample wall material. The experimental procedure, tests, and results are given for each parameter investigated.

Jan 1, 1973

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

By J. R. Thoenen

This circular is part 6 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cableway excavators, and hydraulic monitors; part 3, hydraulic, clamshall, ladder, and diaper dredges; part 4, haulage equipment, particularly industrial cars with locomotive or hoist as the motive power; part 5, conveyor belt, motor truck, pump and pipe line, towboat and barges, and aerial-trams haulage. This circular discusses the application of these various types of equipment to the different types of sand and gravel deposits and contains a reference bibliography. It completes the discussion of excavating problems.

Jan 1, 1936

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By William H. Schiffbauer

The Bureau of Mines is conducting research that is aimed at making the mining industry more efficient in term of both productivity and the health and safety of the worker. As part of this research the Bureau of Mines has integrated a testbed composed of computer and related peripheral hardware to form an intelligent base for performing autonomous mining machine experiments. Although this particular application was con- figured for use on a Joy 16 CM mining machine, its generic structure facilitates its attachment to a variety of mining machine types. The multitasking multiuser computer can be set up for other applications by changing a bubble memory cartridge. The Joy 16 CM implementation includes 96 digital input-output (1-0) ports, 32 analog inputs, 8 analog outputs, 2 serial data channels, and 1 printer port. Operation of the machine can be performed either through a local terminal or remotely through a modem hookup. This report describes a testbed for autonomous mining machine experiments (TAMME)--its hardware, software, and complete system integration--so that it can be used as a foundation for other applications.

Jan 1, 1988

By B. J. Moore

This publication contains analyses and related source data for 269 natural gas samples from wells and pipelines in 18 States. All of the samples were obtained and analyzed during, calendar year 1979 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-one previous publications have presented tine results of 11,883 gas analyses made prior to 1979. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source

Jan 1, 1980

The Minerals Data Source Directory is a compilation of descriptive information on the availability, content, and location of minerals data in the Federal Government. It is intended to assist Government personnel and the general public in locating and acquiring minerals information. Included in the Directory are descriptions of data bases, publications, information systems, and information offices containing data pertaining to all aspects of mineral production, consumption, trade, and related information. These mineral data sources include the Federal agencies such as the Department of the Interior's Bureau of Mines and Geological Survey whose major mission is the collection and dissemination of mineral information. Also included are agencies such as the Departments of Agriculture, Commerce, Labor, State, and Treasury, and the Central Intelligence Agency, whose primary mission is the collection of data in non mineral subject areas, but in which the mineral industry is a component.

Jan 1, 1982

By E. D. Gardner

Oil shale, a long-considered potential source of motor fuel in the United States, is found over an extensive area in the Green River formation in Colorado, Utah, and Wyoming.4/ Oil has been retorted commercially from shale in Scotland for many years,5/ and work done by the Bureau of Mines and other investigators has shown that it is technically feasible to extract oil from American shales.6/ By refining, the shale oil may be converted into marketable products similar to those manufactured from crude petroleum. The present paper, which was finished in 1936, discusses methods that would be adaptable to mining certain American shales, and the treatment applies specifically to conditions iii the Green River formation on Naval

Jan 1, 1942

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

By Thomas V. Falkie

The purpose of this work was to investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors -- geometrical, geological, mechanical, or procedural which affect the delivery rate, and to develop quantitative rate descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily influences the loading function. The geometrical factors -- the dimensions of the work area in relation to the dimensions of the mining machine - were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent independent variables. It is expected that this work will be useful in operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Jan 1, 1972

By H. M. Lawrence

"The land-pebble district, the larger of the two producing areas of Florida, is situated in Polk County and in the eastern part of Hillsborough County. About 80 per cent at the phosphate rock produced in the United States in recent years has been mined from this area. The phosphate ores, locally termed matrix. are beds of sands and clays containing the phosphate pebbles, considered to be Pliocene in age, derived by marine action from underlying Miocene phosphatic marls, and are covered by practically barren sands and clays that have been deposited more recently. Open-pit mining is practiced; hydraulic mining, which has been intensively developed in this district, is used exclusively for mining the matrix and, by some companies for removing the overburden, although drag-line excavators have become established and are proving economical for stripping operations. From the pits the matrix is pumped to adjacent washing plants for beneficiation. The product of the washers. after drying, enters the world markets as Florida pebble phosphate.In this district recovery of the phosphate pebbles by the washing plants has not been particularly effective in the past. The screening, designed to effect a seperation at about 20 mesh (0.033 inches), has not been well controlled. Washer rejects discarded to the waste dumps have contained appreciable amounts of material analyzing above the minimum commercial grade - 66 per cent B.P.L. (bone phosphate of lime). Such losses of commercial fractions should be considered avoidable, and have been discussed at length in a previous paper.3"

Jul 1, 1930

By Laird Crocker

A goal of the Federal Bureau of Mines is to minimize the undersirable environmental conflicts and impacts associated with mineral processing operations. To help reach this goal the Bureau operated a citrate-process pilot plant for the removal of sulfur dioxide from lead smelter sintering machine waste gases to test the process. The process uses a carboxylate solution such as citric acid to absorb sulfur dioxide from waste gases. The absorbed sulfur dioxide is subsequently reacted with hydrogen sulfide to precipitate sulfur and regenerate the solution for recycle. Nominal capacity of the pilot plant was 1,000 scfm of 0.5 vol-pct sulfur dioxide gas. The pilot plant was operated for over 5,400 hr and produced about 55 net tons of sulfur. The operation demonstrated that (1) 99 pct of the sulfur dioxide could be removed from lead smelter sintering machining waste gases containing from 0.1 to 0.6 vol-pct sulfur dioxide, (2) sulfur precipitation and solution regeneration with hydrogen sulfide in conventional stirred vessels was readily controlled, (3) precipitated sulfur could be continuously recovered as a 99.S-pct-pure product by flotation and melting, and (4) 78 dry-vol-pct hydrogen sulfide gas could be produced from pilot-plant product sulfur, natural gas, and steam.

Jan 1, 1979

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

By W. W. Aljoe

The use of protective canopies can result in canopy roofing and/or serious restrictions to operator comfort and vision. To document this experience, BCR conducted a field study of cab and canopy design and application which resulted in a catalog of 164 canopy designs and an analysis of field data which showed no simple relationship between working height and canopy-related problems. The relationship also involves (1) machine frame height, (2) mine floor undulations, (3) operator compartment dimensions, (4) canopy design and location on the machine. Data analysis indicates (1) present technology does not always permit successful application of canopies in working heights below 42 inches, and (2) development of satisfactory low-coal canopies is doubtful. The basic conclusion of the study is that future R&D studies should be directed at development of alternative protection systems and remote mining methods.

Jan 1, 1981

By T. R. Achenbach

1. This, the final report to the U. S. Bureau of Mines on the program with the subject title, presents the data obtained from June 29, 1973, to April 20, 1974. 2. Operating in the Illinois #6 coal seam, the effectiveness of foam opposed to water was compared in reducing respirable coal dust. A combination of 39 foam generators and 14 water sprays were used during the foam tests. Sixty one water sprays were operated during the water tests. Data from 24 shifts using foam and 21 shifts using water are presented. 3. Additional work on foam generator design should be undertaken to provide coverage to a wider area with foam. 4. The general attitude of those working on the foam program and with the miner at the face was positive. It is urged that the work be continued. 5. The minor respiratory irritations evidently caused by an aerosol effect of the surfactant should be investigated. 6. The statistical analysis of the tests will be made and reported by the U. S. Bureau of Mines.

Jan 1, 1974

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By R. Q. Shotts, H. J. Hager, A. C. Richardson, G. D. Coe

"INTRODUCTION In the State of Alabama few mines produce coal clean enough to be marketed directly without being washed. This is particularly true where the coal is to be used for the production of metallurgical coke. In washing plants where single-compartment jigs alone are used to treat a large range of sizes, it has been found that the washed coal finer than 1/4-inch contains a large proportion of free impurities and is much higher in ash content than are the coarser sizes. To reduce the ash content of this fine material with jigs usually entails a greet reduction in capacity and a loss of coarse coal in the refuse. This investigation, conducted by the Southern Experiment Station of the United States Bureau of Mines in cooperation with the University of Alabama and the Alabama By-Products Corporation, was undertaken to determine whether the fine washed coal from jigs could be economically re-treated on coal washing tables.COALS TESTEDThrough,the cooperation of the Alabama By-Products Corporation, samples of fine-sized washed coal were obtained from their washeries at Bradford and Gamma.The Bradford mine, on the Black Creek bed, yields a low-ash, medium-volatile coal with fairly good coking properties. This coal is blended with coal from the Mary Lee bed for coking purposes and compensates for the high ash content of the latter. The Black Creek bed is about 30 inches thick and seam analyses show an ash content of from 2.0 to 4.0 per cent. In the Bradford mine the undercut is about 6 inches high, so that a large proportion of fines is produced."

Apr 1, 1932

By John K. Alley

Despite the extensive use of fluorphlogopite, investigators do not agree as to its exact melting temperature. Data on other fluormicas and on related fluorsilicate systems are largely nonexistent. A knowledge of the melting temperature is necessary for the effective synthesis and use of fluorphlogo¬pite or other fluormicas. The increasing use of two- and three-mica systems to yield polycrystalline ceramics has made more urgent the need for melting temperature information concerning these other fluormicas. This report is part of a program by the Bureau of Mines to synthesize large-size or large-crystal fluorphlogopite and develop a usable reconstituted fluormica sheet. The melting temperature of fluorphlogopite, K2Mg6A12Si6020F4, was found to be 1,383° ±2° C. This temperature was found by studying single crystals of fluorphlogopite, heating behavior of glass of fluorphlogopite composition, and the actual crystallization of fluorphlogopite from a melt that had been heated above 1,430° C. The formation of forsterite or norbergite was directly proportional to the loss of volatiles during the experimentation. Many trials revealed that the only reliable seal was a thick platinum sheet with welded seams. If no volatiles were lost, neither norbergite nor forsterite were formed; fluormica was then the only product. Excellently formed crystals of forsterite with an optical sign different from ordinary forsterite were obtained during the single crystal melting experiments. These crystals resulted from a slow loss of volatiles. A congruent melting of fluorphlogopite is indicated by the data of this report; however, incongruency within a small temperature range is not precluded. A more refined method using phase equilibria-quench methods would be necessary to settle the question absolutely.

Jan 1, 1962