Search Documents

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015

By Tom C. Palangio

Commercially available online particle size analyzers (OPSA) are in their third decade of development (Palangio, T.C., 1985), (Franklin, J. A., Maerz, N.H., 1987), (Maerz, N.H., Franklin, J.A., and Coursen, D.L., 1987). The installed base of operating analyzer numbers is in the hundreds. This paper takes a look at five critically important relationships that users have discovered through the use of OPSA systems. The two key attributes of these systems are: 1) consistency and, 2) historical context compared with traditional practices.

Jan 1, 2016

By S. Lim, G. Walsh, V. Romero

The cable television show, Mythbusters, contacted the New Mexico Institute of Mining and Technology requesting a pressure gauge to be used in underwater testing. The requirements for the gauge were: it must be passive (i.e. require no power to function), it must indicate when a certain, pre-determined pressure was reached, and that indication was to be visual. A pressure gauge was developed, using standard, commercially available rupture discs, set to burst at 500 psi. Underwater testing was conducted using a 400 lb Pentolite charge. Test devices were set out at ranges from 50 to 200 feet from the seat of the blast. The rupture discs showed a lethal range up to 100 feet, but not at 150 feet. This result matched well with the behavior predicted through modeling and simple shock physics calculations. Additionally, the geometry between the incoming shock and the pressure gauge did not seem to have a strong effect on gauge performance.

Jan 1, 2009

By Ayman Tawadrous

Cave mining offers a flexible technique to exploit large, low grade, deep ore bodies with low operating costs. It is typically done in either a top down approach; i.e. sublevel caving, or in a bottom up approach; i.e. block or panel caving, to extract ore bodies that may have been previously considered unfeasible to mine. Sublevel Cave (SLC) mining, in particular, is a cave mining method based upon the utilization of gravity of blasted ore while the overlying host rock fractures and caves under induced stresses and gravity. Thereby the caved waste originating from the overlying rock mass fills the temporary void created by ore extraction to achieve a controlled collapse of the roof.

Jan 1, 2015

By D. Johansson, C. San Miguel, U. Stenman, N. Petropoulos

Blasting is a commonly utilized method in civil engineering projects and mining operations. Ammonium nitrate-based (AN-based) explosives are the most efficient explosives today in terms of handling and performance. However, a side effect is the production of gases. The reduction of these gases plays an important role in the safety and environmental aspects in the working place. Therefore, optimizing the recipes of explosives is vital for minimizing the environmental impact and increasing performance. The aim of the project is to provide results and recommendations on the use of emulsion commercial explosives to support the Swedish mining industry and tunnel-contractors as well as the explosives manufactures. The approach was to test various recipes of civil emulsion explosives to investigate the generation of toxic fumes (CO, CO2, NO, NO2 and NOx) during their detonation. To further increase the knowledge of the influence of different additives, ammonium nitrate prills were added in various percentages. The experimental configuration consisted of magnetite mortar cylindrical specimens with a 50 mm borehole at their center, filled with emulsion explosive. Several tests with different emulsion compositions regarding ammonium nitrate additives (10%, 20%, 25%, 30% and 35%) were carried out in a blasting chamber. The measurement equipment was composed of a flue gas analyzer. The instrument was meticulously cleaned after every test, as well as before and during the tests due to condensation (high humidity and dust) at the inlet of the instrument. The emulsion was manually sensitized with microballons and pumped into the cylinders to ensure lack of bubbles, which could introduce inhomogeneities. The acquired gas concentration data was complemented with temperature, humidity, and VoD measurements. The results showed a linear increase of nitrogen gases as the percentage of ammonium nitrate prills increased. On the other hand, carbon gases had a relatively low coefficient of determination. The VoD data showed a behavior that can be described with a simple quadratic equation.

Jan 1, 2024

By S. S. Bud Jenkins

I went to an underground limestone mine recently to demonstrate the use of borehole liners. The liners were for horizontal holes in a normal “V” cut tunnel round. I hadn’t been in this mine for about 40 years. What a change. Way back they used cap and fuse and lit each fuse individually with a blowtorch. The face was about 40 feet wide and 14 to 16 feet high. They used ladders to get to the upper holes. The rounds were mostly slab rounds. I never saw this happen but had heard several times that the first holes were going off before the last holes were lit. I guess if this was true the use of slab rounds was a plus for safety. As far as I know they never had an accident but it was a scary procedure. There were a lot of scary procedures in the past and thankfully things have changed.

Jan 1, 2010

By J. P. Remi Proulx, Areli Rodriguez, Ruilin Yang

Historically, presplitting has been considered effective in reducing the impact of blast vibrations on highwalls. However, it remains a debated topic: how significantly can it protect highwalls, and is it worth the cost and effort to implement presplit blasting techniques? In hard rock, presplit blasting can leave half-barrels on the highwalls, clearly demonstrating its usefulness. However, in a fractured rock mass, the half-barrels from presplit blasting may not appear in most cases, leading to questions about its role in protecting highwalls. Previous studies in the literature used geophones to measure blast vibrations at far distances and could not ascertain the significant benefit of presplit blasting in reducing the impact of blast vibrations on highwalls. Additionally, no studies in the literature address the role of presplitting in alleviating blasting-released gas pressure that could penetrate joints and open new fractures in highwalls. Yang & Proulx (2019) and Yang et al. (2022) using near-field blast vibration monitoring of signature hole blasts have revealed that the peak particle velocity (PPV) of blast vibrations at a scaled distance of 1 m/kg^0.5 can be reduced by 50% or more for presplit-filtered vibrations. These results have been confirmed for both hard rock and fractured ground. In addition to summarizing the reduction in blast vibrations due to presplitting for both hard rock and a fractured rock mass, this paper demonstrates the relief of subsequent blasting gases after the detonation of blastholes. This is shown through video recordings of gas ejections from a row of empty previously fired presplit blastholes located 6 to 9 meters away from the detonation edge or final buffer row of a blasthole pattern. The results clearly show that presplitting not only lowers blast vibration PPV’s but also reduces the entry of the gases produced by the detonation process into rock fractures and or open joints.

Jan 21, 2025

1974 The Society of Explosives Engineers officially formed to “advance the art and science of explosives engineering” on August 20, 1974 in Pittsburgh, Pennsylvania.

Jan 1, 2010

By Robert Hopler

RBH Note: The Illinois Powder Manufacturing Company was established in 1907 and was acquired in 1957 by American Cyanamid. The latter company left the explosives business in 1969.

Jan 1, 2010

By Jarrod Bonsmann, Zachary T. Plitt

"A surge in mine related deaths in Middle Eastern conflicts over the past few years has prompted research into the mitigation of the impact on a blast loaded vehicle. In past military conflicts, it has been observed that blast loading can cause injury to the brain but the exact cause is unknown [1]. The recent rise in deaths due to Improvised Explosive Devices (IEDs) has led to research that has speculated that the high acceleration experienced by soldiers on a blast loaded vehicle leads to Traumatic Brain Injury (TBI) [2]. This research aims to investigate vehicle designs that can reducethe peak acceleration for passengers on board the vehicle, in the event that the vehicle is blast loaded by an IED."

Jan 1, 2016

By Stephen Mansfield

In open-pit mining operations, the drill and blast processes have a significant impact on the downstream operational performance of crushing and grinding of ores and recovery of metal. The blast pattern parameters, combined with the material properties, defines the run of mine fragmentation, which in turn drives the subsequent energy requirements for further processing and mill throughput. A common parameter used to describe a single hole or collection of holes is powder factor, the ratio of explosives to the quantity of material blasted. One often-neglected aspect of calculating powder factor is the explosives contained within the length of hole drilled into the top of the bench from the previous bench, known as subdrill. Explosives in the subdrill directly affect the bench below and thus do not contribute significantly to the results of the upper bench, even though they are traditionally included in the powder factor calculation. This paper presents geospatial data modelling methods that link individual holes from an upper bench to the bench below. This enables a new method for the calculation of powder factor, whereby the explosives in the subdrill from the bench above are included in the powder factor calculation of the bench below. This method allows for a clearer understanding of the impact of subdrill on fragmentation, and how variations in blast designs in the upper bench, i.e. hole diameter, burden, spacing, subdrill length, explosive type, primer position, etc., and accuracy of implementation, i.e. actual hole depths and explosive mass per hole, affect the powder factor and blasting results in lower benches.

Feb 6, 2023

By Dennis Wilzbacher, John Wiegand

In an effort to reduce the cost of bulk explosives, Vigo Coal Company found that the addition of coal mined at their Friendsville Mine, not only reduced explosive costs, but also appeared to actually enhance blasting performance. The Friendsville Coal lies at the base of the Mattoon geologic formation within the Mcleansboro Group of the Missourian Series of the Pennsylvanian Geologic System in Southern Illinois. Vigo Coal Company commissioned VIBRONICS, INC., an independent blasting consulting company to quantify actual blasting performance. Insitu sonic velocity testing of overburden was conducted to determine the P-wave velocity of the sandstone present at Vigo’s Cypress Creek Mine, where the initial testing was conducted. Numerous VOD (velocity of detonation) recordings were obtained for varying blends of ANFO/Coal (now named Carbo*Prill). Cast blast percentages were determined for both Carbo*Prill and non coal blended bulk explosive blasts. The VOD of the coal blended product was intentionally reduced so as to more closely match the P-wave velocity of the sandstone overburden. Explosive blends containing as much as 40-50 percent coal were tested. Explosive blends containing greater than 30 percent coal, have been used in Cypress Creek Mine overburden production blasts. The coal blends appear to produce better fragmentation and yield excellent cast blast performance. Safer mining conditions were also observed. Flyrock potential was reduced. The blasts produced less back break, producing a safer highwall. Stripping dozer and shovel production rose during the testing period and equipment repair costs were lowered due to an increase in overburden fragmentation. Blasting vibrations were reduced, in part due to the lowered detonation velocity of the ANFO/Coal mixture. The Friendsville Coal Seam appears to contain inherent chemical and physical properties that enhance blasting performance. The use of Carbo*Prill has been approved by MSHA, BATF, the State of Illinois, and the State of Indiana. This paper will provide details concerning testing procedures, blast performance analysis, recommendations and conclusions for using this alternative blasting mixture.

Jan 1, 2007

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Tristan Worsey, Brad Gyngell, Todd Buschjost, Gus Diehr

This paper highlights the opportunities provided by integrating MWD data and drone generated 3D model to industries that use explosive energy to perform useful work as an integral part of their rock extraction process.

Feb 1, 2020

By Jose A. Sanchidrián, Ricardo Castedo, Pablo Segarra, Juan Navarro

A study conducted at a mine site that used traditional field surveying and physical hole spot markings bench marked their combined drill and blast performance. The analysis of the operational expenditure (OPEX) improvement determined there were many measurable cost improvements. A primary factor that most operations have to deal with is over drilling of holes. This alone impacts the cost due to nonproductive labor allocations, excessive explosive costs, increased drill tool costs, increased drilling costs and has an impact on the downstream operation cost such as digging the shot material. Other related investigations also show a downstream impact of poor fragmentation on digging payload tonnes, cycle times, haulage payload tonnes, time to load a truck and the number of passes to load the tuck. The intent of this presentation is to draw attention to aspects of mining we understand but may be missing the big picture effects, such as the ability to reduce the operational expenditures consistently to impact the bottom line. The target audience is across the board from owner operators, drill and blast contractors to blasting contractors. Everyone can benefit from these improvements.

Jan 1, 2019

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Jay Smerekanicz, Florin: Pedersen Gheorghiu, Alan Cameron

In order to expand the capacity of Modern Landtill, a groundwater extraction system consisting of a linear system of pumping wells over 2,700 feet long had to be replaced. The new system would be covered by landtill cells to a depth of approximately 400 feet, and therefore would have to be maintenance free. In addition, the new system had to be proven to be more effective than the previous system, groundwater extraction had to be maintained during construction and construction could not disturb either the landfill operation or nearby residential neighbors.

Jan 1, 2001

By Christopher Jon Preston, Troy Williams, Daniel Roy

There has been significant progress made with narrow vein gold mines in which a second option for crushing has begun to attract attention. To ensure the profitability of a mine that has based its economics on the absence of a crusher station, more than just best blasting practices are required. Using a blasting operation itself as a primary crusher would undoubtedly save enormous capital costs as well as eliminate some of the costs of crushing ore with the result that considerable savings might be realized. The challenge would be to define the conditions necessary to make this type of operation feasible by providing consistent blasting methods that result in a significant paradigm shift with respect to both blasting and current underground crushing methods. A break model has been developed and applied as a technique in designing blasting patterns based on a unit charge blasting geometry and stress reflection from free faces. There are four components to this model and these are 1) unit charge, 2) thermodynamic/energy, 3) stress reflection, and 4) radial break. Some important changes in timing between holes and rows based on rock properties and the percentage of burden moved were also used. On-site testing at a narrow vein gold mine in Quebec Canada, provided measured parameters for the model. No underground crusher was planned - relying only on the fragmentation profile generated by ring blasting. The specification for muck was that the fragmentation profile needed to be 100% < 400 mm (16 in) with no overbreak - with dilution less

Jan 1, 2019

By Robert Boehnke, Bernd Mueller

This contribution presents an innovative, statistically supported method to predict blast vibrations in rock mass. For modelling the processes during and after detonation, a theory is employed which is based on linear momentum (so-called momentum theory), strongly supported by new measurement methods. During the course of the investigations, the following parameters have been found to dominantly influence vibrations: ! charge WB, includes geometrical factors such as borehole length and diameter (kg) ! detonation velocity cd of the explosives used (m/s) ! distance r between the points of emission and immission (m) and the statistically determined negative exponent n ! factor RM or RS of the rock mass which is related to the specific blast momentum and the drilling and blasting technique used and is statistically determined together with the exponent m (mm/kg or mms/kgm)

Jan 1, 2004

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011