Search Documents

By S Lukovic, Robert Briton, Calvin J. Konya

Investigators have reported that charges which are decoupled from the borehole wall produce different fragmentation then those which are fully coupled. The difference in effect could be as a result of energy doss during transmission across the air gap or it could be due to the change in detonation characteristics of the explosive as a result of the change in confinement on the charge during detonation. In order to better understand the phenomena of decoupling, a research project was conducted at the United States Bureau of Mines Station, near Pittsburgh, Pennsylvania. It was decided to use shock and bubble energy tests along with simultaneous velocity measurement to determine the mechanics of decoupling and energy transmission. Two explosives were selected for the test, one dynamite and one water gel. Test results indicated that decoupling could both boost the total energy output of the explosive and that further decoupling would drop the energy output.

Jan 1, 1987

By Rene A. "Moose" Morin, Craig Copping

Innovative concepts in drilling and blast design have been used to remove deteriorated concrete and have enabled contractors to reduce costs and time on St. Lawrence Seaway rehabilitation projects. Time is of the essence on these contracts since the Seaway system is only available for this work during the winter freeze up. Unique electrical sequential initiation systems and specially modified drilling equipment have been used to accurately remove a narrow slice from the 83 foot high lock walls. These new methods successfully reduced demolition time, minimized overbreak and adhered to strict vibration limits.

Jan 1, 1986

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

By Alain Blanchier

Because in Europe and in many other countries as well every new project (quarry, mine, public work) needs a risk estimation to prove its feasibility, a model to estimate flyrock risks became necessary. This paper presents the basic hypothesis which should underlay such a model to estimate statistical flyrocks range for not only some single blasts but a whole project and in particular the way to take into account rockmass or blast pattern parameters variability. It describes a first usable quantitative flyrock model based on the characteristics of the blasting plan and of the generic laws utilised in casting and selective blasting operations and on a statistical approach of rockmass. In a second step, this paper discuss an approach of risks estimation compared to the classical one used in pyrotechnics studies for explosive magazine risks assessment.

Jan 1, 2013

By Brendan O'Reilly, Outokumpu Zinc, Geoff J. Johnston, S Durucan

Historically vibration monitoring has dealt primarily with surface blasting or "near field" monitoring of underground blasts. The Situation at Tara Mines is different, blasting occurs up to 400m underground, with a number of blasts occurring daily and occasionally with residential properties directly above the blasting site. Tara Mines, due to both its location (1.5 km from the rural town of Navan) and stringent planning conditions have always had to monitor, carefully plan and control the levels of vibration from blasting. The statutory vibration limit at Tara allows a maximum peak particle velocity of 7.62 mm/s with no frequency limitations. Levels of vibration have been monitored continuously since mining operations began in 1972.

Jan 1, 1994

By Michael Swisdak, John Tatom, James Tancreto

In 2002, testing was proposed to generate needed data to assist in developing improved explosives safety standards within the US Department of Defense. This testing emphasizes two major areas: (1) full-scale donor/acceptor trials examining debris generation and acceptor response and (2) debris perforation testing of representative roof/wall materials. The full-scale donor/acceptor trials are referred to as the SciPan series. The first three tests in the SciPan series have been completed, as has the first phase of the SPIDER program. This paper describes the status and future of these testing programs, reasons for choosing specific tests, potential benefits, and planning for future phases.

Jan 1, 2006

By John T. Aler

The U.S. Bureau of Mines has been studying the problem of why explosives detonate weakly or misfire during blasting in underground coal mines. Cross-borehole shock wave interaction has been identified as a predominant mechanism causing explosives to function improperly (1)(Underline numbers in parenthesis refer to items in the list of references at the end of this report.). Cross-borehole shock wave interaction can be simulated in a laboratory setting, making possible the replication of tests in sufficient numbers to understand and quantify some of its effects on permissible explosives (2). The work presented here investigates the capacity of explosives to partially recover from the desensitizing influence of the shock wave. The recovery trend of different explosives can indicate optimum blasting patterns useful for minimizing borehole charge malfunctions.

Jan 1, 1991

By Pierre Allard, Wilfrid Comeau

Near-field and close-in blasting can be safe and efficient, near engineered structures, if the dynamic reaction of structural members to blasting vibrations are considered. Safe particle velocity criteria can be derived from allowable safe static flexural deflections and critical frequencies. Control of close-in blasting can be accomplished using low-pass filtering of the particle velocity signal at the critical frequency. The CETE Mediterranee laboratory at Aix-en-Provence, France, a branch of the Ministry of Roads and Bridges has -pioneered this approach and successfully applied it to major road cuts and tunnels in built-up areas, as well as a major powerhouse expansion project in Africa. This approach is presently being used for a spillway rehabilitation project in Quebec, Canada. This paper exposes- the theoretical aspects and gives case histories of its use. The SCS-15 an automated, peak reading, data acquisition device is described.

Jan 1, 1991

By Jaime Huidobro, Mervin Austin

The effect on an explosive column of the sharp transient stress waves generated during the earlier detonation of adjacent blastholes is of paramount importance to explosives users. Some explosives will sympathetically detonate under these stresses. Others may suffer a transient desensitization, arising from a temporary increase in the density of an explosive beyond certain limits and persisting until the explosive mass relaxes back to the original density. Some explosives are so adversely affected by these stresses that the product suffers immediate and permanent loss of sensitivity. These effects can be clearly seen while blasting in tough conditions such as burn cuts or wedge cuts and in materials, such as coals, that propagate shock waves well.

Jan 1, 1992

By Lewis L. Oriard

Near the village of Villarino de los Aires, in the province of Salamanca, Spain, was an existing underground hydroelectric power plant. A major enlargement was undertaken to increase the electrical generating capacity, under a contract awarded to a joint venture of Dragados y Construcciones, S. A. (Spain), Entrecanales y Tavora, S. A. (Spain), and S. A. Conrad Zschokke (Switzerland). The enlargement required the excavation of a large and complex underground system of tunnels, shafts and chambers adjacent to existing facilities and interconnected with these facilities. The existing machine hall and transformer chamber were both extended, requiring the blasting of the existing end walls. The drilling, blasting and excavating of the underground system had to be done without damage to existing underground chambers and tunnels, or any of the existing structures, equipment or instrumentation facilities, often within just a few feet of the blasting. This required careful control of vibrations, airblast overpressures and dust.

Jan 1, 1997

By John L. Floyd

One of the key factors that controls the overall profitability of surface operations is the required volume of excavated material. If the overall angle of final walls can be maximized the amount of material excavated will be reduced. However, as the slope angle becomes steeper the wall's factor of safety decreases. As a result, the development and implementation of efficient wall control blast designs becomes critical to achieving stable walls. Many site specific conditions should be taken into account when defining the methods that will be used to lessen blast induced wall damage. This paper will discuss the steps needed to properly evaluate the site and develop efficient designs. Four variations of wall control blast designs will be evaluated in terms of cost and performance. In addition, the paper will include the quality controls needed to successfully implement and refine the blast design.

Jan 1, 1998

By Philip M. E Thomas

For over sixty years man has struggled to defeat the natural swamp lands known as the Florida Everglades as demand for land to support the burgeoning population growth in the state continued almost unchecked. Over the past ten years there has been a growing awareness that this land development could wipe out a whole ecosystem in a very short time unless steps were taken to reverse the trends. In 1991, a state law called the Marjory Stoneman Douglas Everglades Protection Act was enacted giving power to the South Florida Water Management Board to condemn certain lands for conversion to manmade swamp lands, designed to filter polluting run-off water from the agricultural lands around Lake Ockeechobee.

Jan 1, 1994

By Mark D. Kirkbride

This paper outlines the process for designing a hard rock blast in an underground coal mine. The coal mine is located in Western Kentucky and operates four continuous miner units at 7 unit-shifts per day. The mine operates in the Western Kentucky No. 11 Seam with local variations from 4.5 - 5.5 feet seam thickness. The seam has sporadic siderite deposits. Usually these deposits do not significantly interfere with the mining process. When previous siderite deposits were encountered they were small enough to drop an entry for a couple of crosscuts. The blasting plan was called for after a siderite deposit was encountered in the belt entry at about one third of the panel length. The other sides of the panel had been previously mined and sealed so the decision was made to mine through the siderite deposit with the continuous miner instead of abandoning the panel. The deposit was approximately 300 feet in length down the belt entry. Mining through the deposit with the continuous miner was expensive in both terms of production and of wear and tear on the continuous miner. A blasting plan for the siderite deposits was designed to minimize damage to the continuous miner should a similar situation occur.

Jan 1, 1999

By John C. Brulia

PowerAN is a tradename of Atlas Powder Company for a new line of explosive products comprising blends of emulsion and ANFO in a variety of bulk and packaged grades. The bulk PowerAN grades are either augered or pumped depending upon emulsion content. Augered PowerAN blends contain up to 60% emulsion. Pumped PowerAN grades have an emulsion content of 75% or higher. The blending of PowerAN is usually accomplished at the borehole to satisfy specific borehole conditions. Packaged PowerAN grades are produced in several types of mix plants in diameters of 4" and greater. PowerAN 300 (30% emulsion) and PowerAN 500 (50% emulsion) are the two most popular grades and their chief application is as an economical, high energy replacement for ANFO HD in wet holes. PowerAN combines the cost effectiveness of ANFO with the high performance of emulsions, permitting the blasting engineer to strike an optimum balance between drill pattern expansion and increased productivity according to need.

Jan 1, 1985

By Ingvar Hansson, Bjorn A. Jonsson, Bernt Larsson

In the Kiruna Research Mine, Sweden, four large open stopes have been mined, leaving intermediate piIlars and crown pillars. At the final stage of mining mass blasting of the crown pillars above two of the stopes was carried out. The crown pillars contained some 290,000 tons of iron ore. In the mass blast a new initiation technique was used, utilizing the new non-electric system NONEL ? UNIDET. The blasting technique including vibration control is described. The mass blast resulted in high recovery, good fragmentation and low vibration levels.

Jan 1, 1986

By Gregory Lorsbach, Wade Hutchison, Earnest Grigoryan

Comparing measurements from multiple seismographs, particularly when the instruments are deployed in a “side-by-side” situation, is often problematic. Measurements often differ by as much as a factor of two. These differences are attributed to issues related to calibration, geophone coupling, and differences in geology over very short distances. Unfortunately, these explanations are often purely qualitative, but are accepted as factual. Shake table testing often demonstrates that those seismographs that indicate large differences for a particular vibration event, may correlate within a few percent of each other and the known shake table input. Geophone coupling also does not fully explain the difference in measurements since geophones in side-by-side measurements are deployed identically. Differences in geology do not explain the difference in measurements since it would be unrealistic to expect significant differences in distances less than one meter in a normal monitoring situation. Utilizing a new technological approach to vibration measurement and analyzing numerous side-by-side measurements, it has become clear that a significant portion of the observed differences between seismograph measurements are instrumentation induced. This study examines and describes some of the most significant sources of the seismograph error budget.

Jan 1, 2005

By F O. Otuonye

Full-face blasts were fired in a 12 x 8 ft drift of an underground hardrock mine in a basalt formation with porphyry copper to study the effects of drill pattern and explosive type on the size distribution of the resulting muckpile. Each muckpile produced by five full-face blasts was sampled four times with a scooptram equipped with a 5-cu yd bucket and the size distribution of the broken rock in each bucket was determined by screen analysis. Results show a strong dependence of the fragment size distribution of muckpile on the blast pattern and explosive type for a given rock type. The mean fragment size of the broken rock was compared with the predictive equations of other investigators. Random sampling of the muckpile from full-scale blasts and screen analyses of the samples are recommended in assessing the size distribution of the broken rock because of scaling errors that are inherent in full-scale blasts when designed from results of small-scale tests.

Jan 1, 1985

By Lon D. Santis

This paper reports on an evaluation of the safety characteristics of short lead, 5 centimeter (cm), Magnadet1 detonators. The Magnadet initiation system uses magnetic induction principles to transfer electric energy from the firing line to the detonator without a physical connection. This study was initiated because the Magnadet initiation system represents a new technology and the Bureau is interested in ensuring that no potential safety hazards are introduced into the nation's mining environment. The Magnadet system and its proper use are described along with a discussion of how it works. The potential hazards examined are: stray current from mine service power, lightning, DC current, static electricity, and radio frequency transmissions. Tip strength is also evaluated. Experiments were conducted to evaluate some hazards and theoretical methods were used to evaluate others. The results showed that the Magnadet short lead initiation system does not exhibit any unusual safety hazards. The new system is at least six times as resistant to common hazards as currently used electric initiation systems, so long as the insulation is intact.

Jan 1, 1992

By David Yanez

The hydroelectric project "El Cajón" is currently under construction in the state of Nayarit, on the Santiago River, in western Mexico. This project is comprised of a Concrete Face Rockfill Dam (CFRD) with a rockfill necessity of 10,5 million cubic meters and it reaches a height of 188 m. The generation equipment includes two turbines with a total installed capacity of 750 MW.

Jan 1, 2006

By D Vrkljan, Z Ester

There was no use of emulsion explosive at Croatia till 1997. Several attempts have been done to bear out the economical and technological affordability of applying the emulsion explosive for open pits and to make the contractor familiar with characteristics of emulsion explosive exepiting experimental blasts series at more open pits on different kinds of rocks. Testing the efficiencies of emulsion explosive there has been applied the original method for linear enlargement of burden of Sc.D. Josip Krsnik’s from Mining, Geology & Oil Faculty, University at Zagreb. The method of linear burden’s enlargement, in distinction from other methods concerning these problems, has been carried out in situ, under real exploitation conditions whereas the physical-mechanical rock’s features, geological conditions, bed relations and rocks’ structure influence the blast efficiencies. On such way, by mean of method the precise boring and blast sizes will be reached for each kind of rock and geological structural bed’s conditions referring to specific explosive type. The technical-economical analysis indicates the most favorable explosive type for specific bed.

Jan 1, 1999