Search Documents

By C. H. Zhou

Cryogenic grinding of Printed Circuit Board will bring less pollution, reduce energy costs, smaller particles, regular particle size, efficient process, separation various materials due to different fracture toughness. Systemic studies of recycling discarded Printed Circuit Board (PCB) by low-temperature modification and cryogenic grinding have been made in this paper. Firstly test mechanical property of PCB at different low-temperature, including impact strength, flexural strength, and shear strength. Do experiment on the power consumption of different cooling temperature, The results show that the average power consumption is lower between -30? to -60? and the average power is decrease in evidence at -30?. Use ZKB type double roll shear crusher to crush PCB to 20mm×20mm particle size, in a temperature range of -10 ~ -30? Used R type mill to grind sample to minus 3mm under different working condition, the average power consumption is decrease in evidence from -10 ? to -30 ?, power consumption is the lest at rotational speed is 1180rpm.

Jan 1, 2014

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By Y. S. Sun, P. Gao

"In this investigation, a pilot-scale suspension magnetization roasting reactor was introduced and used to enhance magnetic properties of an iron ore. Consequently, the effects of roasting temperature, reducing gas CO flow rate and fluidizing gas N2 flow rate on the magnetization roasting performance were investigated. The results indicate that the hematite and siderite are almost completely converted into magnetite by a gas mixture of 3.5 Nm3/h CO and 2 Nm3/h N2 at roasting temperature of 520 °C. Under the optimized conditions, the magnetic iron concentrate with an iron grade of 60.18% and iron recovery of 90.17% was achieved. The XRD and Fe mineral phase analyses revealed that most of the hematite and siderite were converted to magnetite, and the magnetic properties were greatly enhanced. INTRODUCTION The steel and iron industry in China has rapidly developed in recent years requiring a large quantity of iron ores. Low-grade and complex iron ores are currently the overwhelmingly dominant mineral resource for iron in China. Therefore, China depends on imported iron ore resources heavily, resulting in an increase in the production costs of iron-making and steel-making[1-3]. Using domestic resources to produce a steady supply of high-quality iron ores is an important step toward the sustainable development of the steel and iron industry[4-5]. The iron ore from Jiuquan iron and steel company is abundant and recognized as typically complex iron ore resources in China. Magnetization roasting followed by low-intensity magnetic separation has been proven as the most feasible methods to upgrade refractory iron ore[6-10]. In present research, an innovative roasting technology, namely suspension magnetization roasting, was developed and applied to recover iron from a typical refractory iron ore. Suspension magnetization roasting technique and equipment developed by Prof. Yuexin Han’s Group at Northeastern University (NEU) is an effective way for the utilization of refractory iron ore. The advent of suspension magnetization roasting will, in China and even globally, produce a significant technological revolution in the field of iron ore beneficiation. Based on the previous works, this paper mainly described experiments on the separation and recovery of iron from a complex refractory iron ore by means of suspension magnetizing roasting and low-intensity magnetic separation processes. The purpose of the research is providing a new technology for effective utilization of refractory iron ore. Process parameters that affected the separation and recovery rate of iron were conducted and optimized, and the reaction process was analyzed by XRD and Fe mineral phase analysis."

Jan 1, 2018

By P. K. Fedotov

At projecting mining-concentrating complex at the deposit ?Zapadnoye? (Russia) it was considered to enable an opportunity of refusal from conventional SAG-mills. First time a scheme of gold bearing ore destruction using Roller Press RP 5-100/90 had been developed and integrated. The plant was launched in summer 2003 and presently it has achieved designed technological parameters, processing throughput comes to 1 million tons of the ore per year.

Jan 1, 2014

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By Wei Sun, Xue-feng Cao, Lei Sun, Run-qing Liu

The flotation performance of kaolinite in laboratory micro-flotation was investigated with 3- (dodecyloxy) propan-1-amine (ON12) as the collector. Compared with dode cylamine (DDA), which is commonly used as the bauxite reverse flotation collector, ON12 shows stronger collecting ability for kaolinite than using the same amounts of DDA, when experimental pH value reaches more than 6. With the addition of ON12, the isoelectric point of kaolinite shifts to 6.1 from 3.6, which suggests a strong adsorption between kaolinite and ON12. Infrared spectra analysis indicates that the type of ON12 adsorbed on the kaolinite surface is mainly of electrostatic adsorption. Molecular dynamics simulation further indicate that electrostatic adsorption of ON12 cation on kaolinite (001) surface based on electrostatic interaction between NH4+ and O atoms. ON12 will be suitable for bauxite reverse flotation with the efficiency depressors of the diaspora.

Jan 1, 2014

By S. V. Volkova, S. V. Mamonov, T. P. Dresvyakyna

"The purpose of the work is complex processing of sulphide-magnetite ores with the separation of iron into iron concentrate, copper and noble metals into copper concentrate.The work shows the research results of the material composition of the sulfide-magnetite ore in the South part of the Peschanskoye deposit. According to the research results it is found that ore contains 0.59% of copper, 66% of which is related to chalcopyrite; 39.9% of iron, 81% of which is magnetite and 3.87% is sulfur, 42% of which is associated with pyrrhotite, 65% of which is a monoclinic modification. According to the results of the mineralogical analysis, it is found that the main iron-containing mineral in the ore under study is magnetite, the content of which is 45%. In addition to magnetite, iron is found in carbonates, pyroxenes, amphiboles, chalcopyrite, pyrrhotite and pyrite. The main copper mineral in the sample is chalcopyrite; covellite, chalcosine, bornite have a subordinate value. The total content of copper minerals in the sample is about 1%. The processing technology provides the three-stage grinding of the ore to a size of 65% of the class-71 µm; a cycle of copper flotation; a cycle of pyrrhotite flotation; wet magnetic separation of flotation hosts. The following optimal parameters are established for the ore under study: the alkalinity of the slurry is 250-280 g/m3 of free calcium oxide in the liquid phase of the slurry; the duration of the main copper flotation is 20 min; the consumption of butyl potassium xanthate is 20 g/t; the consumption of the foam generator T-92 is 15 g/t; the consumption of copper sulfate for the activation of pyrrhotite is 300 g/t; the magnetic field strength is 1500 Oersteds.A complex flotation-magnetic technology for the enrichment of sulfide-magnetite ore has been developed in the laboratory in order to produce a copper concentrate containing 21.6% of copper with 91.7% extraction and an iron concentrate with 66.5% of iron mass fraction and 1.2% of sulfur with an extraction of iron into the concentrate of 87.9%."

Jan 1, 2018

By Marlize Barkhuizen, Chris Aldrich

"Owing to environmental constraints, safety considerations and competitive pressures, the development of model-based process control and other automated systems have experienced considerable growth in the last few decades. Reliable process models are usually critical to the successful implementation of these systems. In complex processes, these models are often constructed from process data, as modelling from first principles may not be feasible or cost-effective.Even so, modelling or identification of nonlinear systems from historic plant data can be a daunting task and in the process industries the problem is complicated by the presence of noise from various sources, nonstationarity of the data, intermittence, such as observed in particulate flows, etc. Traditional methods, such as frequency analysis and linear modelling do not handle these systems well. Similar problems arise with the application of nonlinear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase or pseudophase space, since these methods were not originally designed to deal with noisy systems.With singular spectrum analysis, the data are embedded in a high-dimensional reconstruction, followed by the introduction of a new coordinate system, where the origin is moved to the centroid of the reconstructed system states and the axes are represented by the dominant principal components of the states (points)."

Jan 1, 2003

By N. Tsoni

The separation and recovery of fine and ultra-fine particles during the processing of mineral commodities by conventional separation methods is difficult and inefficient. This is due to the problems posed by the very small size of the mineral particles. The fine and ultra-fine mineral particles are either generated during size reduction processes or are necessitated by liberation size. This problem is expected to deteriorate, as deposits of even lower grade are processed. The inefficiency of the conventional separation methods with regards to the processing of very fine particles leads to the loss of considerable quantities of mineral commodities to the tailings. Novel methods and techniques as well combinations of known methods have been tested over the years. Among them, selective aggregation, along or in combination with flotation, has been given much attention. This study deals with the application of hydrophobic agglomeration as a separation method for very fine particles. The selected mineral system is magnesite/quartz, due to its sensitivity to physi-cochemical separation methods. The aim was the selective agglomeration of magnesite using sodium oleate. Tests on single minerals revealed that separation seems feasible and efficient. The parameters examined were: pH, quantity of sodium oleate, conditioning time, and, finally, settling time. Tests carried out on artificial mixtures of the two minerals, under various proportions, confirmed the results obtained from single mineral tests but they were slightly inferior. Finally, hydrophobic ag-glomeration tests were carried out on single and artificial mixtures of minerals using sodium oleate and petroleum as reagents. The results show that the addition of petroleum improves the results. In conclusion, hydrophobic agglomeration can be applied successfully even for fine particles of difficult-to-be-separated systems such as magnesite and quartz.

Jan 1, 2014

By Yuexin Han, Wenbo Li, Yan Shan, Yanjun Li, Shumin Zhang

"With the accelerating pace of resource extraction, the quality of resources is decreasing, and the old tailing dams which have served for several decades have become the focus of attention. The secondary recovery of valuable metals in the tailings is an important aspect of the comprehensive utilization of tailings. The average iron content of iron tailing is 8%-12% in China. The research aimed at exploring the low-cost and efficient technical route to recycle eastern tailings of Anshan iron mining area. The purpose of the research is to scientifically find the rational conditions of magnetizing roasting and to provide an increase in recovery and quality of concentrates. The eastern tailings of Anshan mining area belong to high silicon bearing iron tailings, iron mainly exists in form of hematite-limonite with an iron grade of 10.60%, the main component of gangue is SiO2 with a grade of 76.22%. In order to reduce the influence of the tailings on the environment, fluidized magnetizing roasting and low intensity magnetic separation for the eastern tailings of Anshan mining area were carried out to improve the utilization of the tailings. The results indicated that an iron concentrate with an iron grade of 65.30% and a recovery of 85.85% could be obtained under the conditions of gas flow rate 8 m3/h, H2 concentration 50%, fluidized magnetizing roasting temperature at 600? for 20s. Phase analysis, magnetism analysis and XRD analysis on roasted materials indicated that hematite-limonite could be transformed to magnetite during the fluidized roasting, then the effective separation of iron and gangues could be made easily by the weak magnetic separation. INTRODUCTION It is universally acknowledged that the grade of iron ore in China is low, the output rate of iron ore tailings is high, usually more than 60%. At present, the comprehensive utilization rate of iron ore tailings is low in China. Generally, the iron ore tailings are stockpiled in the tailings dam. The tailing dams not only occupy a lot of land, but also takes a lot of money to construct and maintain. In addition, the noxious substances in the tailings, such as residual flotation agents and heavy metals, have a severe impact on the ecological environment. There is little doubt that tailing dams have a visual impact on the environment due to their regular geometric shape. Iron tailings can be treated as compound mineral, which is an important component of comprehensive utilization of mineral resources, and is an has been widely concerned. Lots of scholars have done a large amount of research work on a large number of iron ore tailings. Since the iron mineral crystal grain size is fine and the iron grade is low, the iron tailings have failed to achieve good selection criteria."

Jan 1, 2018

By H. Tiefel, M. Schneider, T. Neesse, J. Regler, J. Dueck, F. Donhauser

In practice the advantages of high-quality hydrocyclone separation are often reduced due to varying feed suspension properties, solids concentrations and particle size distributions. Control systems of large hydrocyclones are usually fitted with controllable underflow nozzles, which is not practical for small hydrocyclone batteries. Therefore, a new control system for a battery of hydrocyclones with a nominal diameter of 150 mm was invented at the LUR in cooperation with AKW Apparate und Verfahren GmbH & Co. KG. This process was developed for bentonite slurry regeneration associated with tunnel excavation using bentonite slurry as a transport aid and lubricant.

Jan 1, 2003

By C. Perez

In mineral processing plants it is important to estimate rock composition, size and grindability to improve control of the grinding process. It is well known that variation in ore grindability and size distribution directly affects mills power consumption and throughput. This paper extends a general machine vision approach for on-line estimation of rock mixture composition using color information. Our proposed rock lithological recognition method requires the following steps: division of each image into sub-images, color feature extraction using the Binary Quaternion-Moment-Preserving thresholding technique (BQMP) and support vector machines (SVM) for classification. The BQMP thresholding technique splits the image in two and chooses representatives of each half using the histogram as features. The statistical parameters of the color data can be expressed using the quaternion moments into the representatives. This method can be recursively applied to the sub-images, obtaining 5x2n features in n iterations. Once the feature vector has been computed, each vector is assigned to one of three classes using a classifier. The method was tested on a database containing 20480 sub-images (64x43 pixels) of five ore types as follows: massive sulphide (MS), disseminated sulphide (DS), net textured (NT), gabbro (G), and peridotite (P). These ore types were assigned to three grindability classes: soft (MS), medium (DS and NT) and hard (G and P). The database was divided in 2 subsets: 15360 sub-images used for training and cross validation and 5120 sub-images used for test. The classification accuracy was compared with a method previously published based on a mixture of principal components analysis (PCA) for color, and wavelet texture analysis (WTA) for texture feature extraction. WTA-PCA approach reached a 76% accuracy in test while our BQMP method reached 90% of classification accuracy using only color features. Experimental results show that our proposed method yields excellent results compared to previously published results. Keywords: rock classification, lithological classification, grindability estimation

Sep 1, 2012

By Tong Guan, Guangqin Fu, Lihong Deng, Xiaotong Zhou

The raw ore contains many kinds of valuable metal elements. It is rich in valuable metal elements, such as Pb, Zn, Sb, Sn, Ag and is associated with S,Fe,As,In,Cd. A new technology which includes medium intensity magnetic separation, preferential lead flotation, zinc-sulfur bulk flotation, zinc-sulfur flotation separation, tin gravity separation and tin slime flotation was chosen to recover valuable minerals in the raw ore, and the iron concentrate, the lead concentrate, the zinc concentrate, the sulfur concentrate and the tin concentrate can be obtained. To the zinc-sulfur bulk concentrate with the grade of 7.21%Zn and 16.97%As acquired by the zinc-sulfur bulk flotation, two different flowsheets of Zn-S separation technology are chosen to study. The lab test shows that when using lime+DM as depressor, the zinc concentrate assaying 47.73%Zn with the recovery of 95.01% can be obtained and the test indexes are better than that of the flowsheet which using lime as depressor. At the same time, the Cd content is 0.65% and the In content is 0.10% in the zinc concentrate, so they all reach the smelting comprehensive recovery standards and the As content decreases to 0.23%. Finally the flotation separation of christophite and As-bearing sulfide minerals can be successfully realized.

Jan 1, 2014

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In this paper, new strategies are discussed for producing additional value.added products after evaluating the present beneficiation practice in terms of changing market scenario, processing capability of the plant and ore characteristic. They would entail use of MGS - an enhanced gravity separator, for recovering additional products from plant tailings; production of ferruginous coarse concentrates (-3+0.5 mm with ~46% Cr2O3) using jigs; production of marketable grade lumpy (-40+10 mm size) concentrates from low grade siliceous ore using jigs and >2.8 Cr/Fe ratio siliceous ore fines treated in the Chrome Ore Beneficiation plant gravity circuit units and low intensity magnetic separator. The studies indicate that it is possible to recover 79-80% of the chromite, against a theoretical maximum of 82% from both the ore types, in the form of several marketable grade concentrates that would also include refractory grade."

Jan 1, 2003

By D. Jamróz, A. Surowiak, T. Niedoba, P. Pieta

"The separation of coal material of three types of coals originating from three various Polish hard coal mines (types 31, 34.2 and 35, according to Polish nomenclature, which were steam coal, semi-coking coal and coking coal) into particle size fractions and then into particle density fractions was done and then the following parameters were measured for each particle size-density fraction: combustion heat, ash contents, sulfur contents, volatile parts contents, analytic moisture. In this way a 7-dimensional vector of data was created. Using methods of factor analysis the important features of coal were selected, which decide about their membership to individual types. To evaluate the appropriateness of the applied method the Bartlett’s sphericity test as well coefficient of Kaiser-Mayer-Olkin (KMO) were used. To select important factors the Kaiser criterion and Cattell’s scree test were used. The obtained results were compared with the results obtained in previous works by means of observation tunnels method. The results showed which particular features are crucial to define the type of coal what is also important to select appropriate method of its enrichment.INTRODUCTION Coal extracted from the mine is often a mixture of coals of various quality originating, for example, from various coal layers. One of the most important issues is to determine its quality, what means to verify if it fulfills certain requirements. Usually, such parameters as combustion heat, ash contents, sulfur contents, volatile parts contents and analytic moisture decide what the coal quality is (Drzymala, 2009). Such investigations are expensive and time consuming. That is why it seems to be important to determine the mutual connections and interactions between them what would make possible to reduce the amount of the necessary parameters. This issue was already investigated with successes in several works [Jamróz and Niedoba, 2013; 2014; Niedoba, 2015]. This work is another approach to this problem. Here, the investigation of possible reduction of researched parameters was done on the basis of the factor analysis. The obtained results confirm the earlier observations."

Jan 1, 2018

By Jacek Kolacz

A new sensor based sorting system has been developed, based on complex image analysis, where an image texture and a shape pattern is considered for identifying particles for separation. The sorting system employs different images generated by visual light and X-ray to provide maximal information about processed particles. Application of X-ray makes it possible to analyse the internal structure of the particles, which provides a 2D image with complicated texture, however, which contains valuable information. The advanced system for the texture and the pattern recognition is applied to analyse these images simultaneously, to provide the required identification of the particles for efficient separation. The mathematical models applied during identification and separation, are assisted by high speed calculations being specially optimised for this kind of process. This allows sorting with high capacity and high accuracy, which is critical for practical applications in mineral processing. The paper describes a number of tests during sorting of iron ore and coal with high separation efficiency.

Jan 1, 2014

By A. Buchanan, M. Mirnezami, A. L. Restrepo, J. A. Finch, M. S. Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally revealed two aggregation maxima at pH 8-10 and 10-12. From measurements on sphalerite and silica suspensions the double maxima were replicated by Zn ions (pH 8-10) and Mg ions (pH 10-12) corresponding to the presence of zinc hydroxide and magnesium hydroxide, respectively. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By R. Hejazi, Saghaeian. M., H. Abedini

Continuous vacuum belt filters mainly carry out an important duty in the solid-liquid separation processes such as iron ore concentrate dewatering. However as the particles become finer, the resistance to filtration and dewatering would increase and as the result cake moisture content tends to increase. So in recent decades, using additives in order to improve the filtration performance has been considered by many researchers. In the present study, the effect of several surfactants on the filtration rate and cake moisture content of Chadormalu iron ore concentrate (80% =40 micron) was investigated using a laboratory scale vacuum filter. The results of several tests indicated that a non-ionic surfactant (Lauryl Alcohol Ethoxylated, LAE) has the best performance on reducing the moisture content of the cake and reducing the cake formation time. The optimum dose of LAE was found to be 300 g/ton which reduced the concentrate cake moisture content from 13.76 to 11.28% (wet weight base). Some industrial filtration tests were performed in Chadormalu iron ore concentrate plant to prove the effectiveness of this surfactant. The surfactant is mixed with water and added to the concentrate slurry before distributing on the vacuum belt filter. The industrial and experimental results were almost similar, so that adding about 300 g/ton of LAE would reduce the final cake moisture content from 12.87 to 10.76%.

Jan 1, 2014