Search Documents

By Terry J. Briggs, Ian J. Kelso

"Abstract- The Century mine in northwest Queensland,Australia, is a major sediment-hosted zinclead- silver orebody, located within the western Mount Isa Basin. Stratiform, carbonaceous shalehosted mineralization is developed within Proterozoic shale and siltstone sequences of the Lawn Hill Formation. CRA Exploration Pty Ltd (CRAE) discovered the Century deposit in 1990 and open pit mine development commenced in 1998 under the ownership of Pasminco Century Mine Limited (PCML). The deposit contains an identified mineral resource of 105 Mt @ 12.1% Zn + 1.7% Pb + 46 g/t Ag (Broadbent and Waltho, 1998) which is currently being mined at a rate of 5 Mt/y.In December 1998, an exothermic reaction was observed between explosives spilt onto shale drill cuttings from a blasthole. This reaction is referred to as ‘reactive ground’ and has the potential to cause premature detonation of explosives in a charged blasthole with catastrophic consequences. The incident led to a subsequent geological and geochemical assessment of the different rock types at the Century deposit and their potential reactivity with ammonium nitrate-based (AN) explosive products. This assessment was conducted in an attempt to characterize zones safe for blasting with uninhibited AN-based explosive products. A direct result of this study is a set of procedures outlining the use of different AN-based explosives in areas defined as potentially reactive or non-reactive for the different lithologies present. Black shales contained in both the waste and mineralized sequences contain the sulfide mineral pyrite (FeS2), which is thermodynamically unstable with AN contained in commonly used explosives. The potential reactivity of partially weathered pyrite can ultimately result in the decomposition of an AN-based explosive. It was determined that only pyritic black shales showed any potential to react with AN, irrespective of their position in the stratigraphic sequence. Other lithologies present at Century, including Proterozoic sandstone and Cambrian limestone, are classified as non-reactive with AN. This is a geological risk management situation present at the Century mine."

Jan 1, 2001

By K. Wongpreedee

Recovery and recrystallization of Au wire can degrade strength and alter conductivity properties during exposure to elevated temperature. Au Deformation Processed Metal Metal Composites (Au DMMC's) are being developed for electronic applications requiring high conductivity and high strength. This paper discusses the relationships between microstructure, strength, and resistivity of Au DMMC's. It also presents the results of a recent study on the elevated temperature stability of Au DMMC's of several compositions. Au-7 vol %Ag, Au-14 vol %Ag, and Au-vol 7%Pt DMMC samples were prepared by a powder metallurgy technique. All specimens were processed into wire by extrusion, swaging, and drawing. The smallest final diameter of these wires was 120 ?m. Thermal stability was analyzed by electrical resistivity measurements to determine the relation between transformation rates and time at elevated temperature. The extensive deformation used to produce these composites reshaped the initially equi-axed powder into filaments that are 30 to 100 nm in diameter and 16 to 180 mm in length. The small filament diameter confers high strength on the composite. The high conductivity can be explained by electrons flowing parallel to the filamentary microstructure aligned with the wire axis. Using the Avrami and Arrhenius equation relationships, it is possible to predict the times and temperatures needed to achieve various degrees of homogenization. The Au DMMC's were found to have good thermal stability compared to conventional coldworked Au interconnection wires. Although these composites will revert to solid solutions if exposed to high temperatures for prolonged time periods, their relative stability is sufficient to allow them to maintain their twophase microstructure during the anticipated lifetime temperature profiles of many products.

Oct 1, 2003

By Tim Robinson, Michael S. Moats, William G. Davenport, Andreas Filzwieser, Andreas Siegmund, Shijie Wang

This survey continues the long tradition of providing a snapshot of operating data from industrial electrorefineries. It is a supplement to previous surveys that were performed in 1987, 1991, 1995, 1999, 2001, 2003, 2007, 2010, 2013 and 2016. Analyses of current data and historical trends are presented. Examples of innovations to reduce costs, improve productivity, and improve quality are provided. In general, refineries continue to increase productivity while treating anodes with more impurities. INTRODUCTION This manuscript analyzes global survey data provided by operating copper electrorefineries. This paper continues a series of surveys of copper refining tankhouses that started in 1987 (Schloen, 1987, 1991; Schloen & Davemport, 1995; Davenport et al., 1999; Robinson et al., 2003; Moats et al., 2007, 2013, 2016). In this installment, data collected from 2015 and 2018 will be presented and analyzed. The 2015 survey data were presented at Copper 2016 in Kobe, Japan. This survey will continue the analysis of previous data to illustrate long term trends in copper electrorefining, which were originally presented at the Davenport Symposium in October, 2014 (Moats, Robinson, & Wang, 2014). Refineries who supplied surveys are listed in Table 1. Cathode production data from 2015 and 2017/18 (from surveys presented in 2016 and 2019) are provided to indicate which plants provided surveys and when. This manuscript presents operating data for ~6.5 million tonnes of copper production, which represents 30–35% of the world’s copper electrorefining production. The detailed survey results are available upon request from the corresponding author.

Jan 1, 2019

By Caitlyn J. McKinley, Ahmad Ghahreman, Maziar E. Sauber

Ever-growing global needs for critical metals, such as rare earth elements (REE), and base metals, such as copper and nickel, and their environmental impact motivated the pursuit of sustainable flowsheets. Regeneration of hydrochloric acid in chloride-based leaching flowsheets as a critical unit operation is an example of such endeavours. This study presents an efficient hydrochloric acid regeneration method from a magnesium chloride solution waste by addition of sulphuric acid in relatively low temperatures. The effects of temperature, initial magnesium chloride concentration, amount of sulphuric acid added, and airflow are examined. Experimental work are focused on temperatures between 80 and 95°C, initial magnesium chloride concentrations of 2 to 5 M, 100% to 220% stoichiometric sulphuric acid additions, and airflows between 200 to 600 mL/min. The developed technology recovers hydrochloric acid at a high rate and concentration with a relatively small environmental footprint. INTRODUCTION The mining and metals sector is under increasing environmental and economic pressure to make more efficient use of chemical reagents and energy in the production process. This affects several areas of process and flowsheet design such as the selection of the most appropriate unit operations and the overall design of the process steps paying heed to sustainability. Owing to the inherent inefficiencies of physical and chemical processes used in the mining industry, there will be materials and streams generated that are not a desirable part of the envisaged flowsheet. Thus, methods are implemented to recover and recycle such effluents. If the recovery and recycling are not economical, then procedures are followed to neutralize and dispose these effluents. In many cases, these effluents are potential contaminants or hazardous materials, and their disposal should be looked at in a much larger context. The safe management of the contaminants and hazardous effluents is a daunting problem in the mining industry and is fraught with technological, economic, social, and political challenges.

Jan 1, 2019

By Mario Bureau

Need for a lab assembly reaching better and consistent static anchorage capacities

May 1, 2013

By D. Naden, D. J. King

"The high capital and operating cost of liquid-solid separation circuits in hydrometallurgical plants has led to an increased focus on the use of in-pulp systems for metals recovery in order to eliminate the need for solids washing and to reduce the need for liquid-solid separation.Carbon-in-pulp (CIP) has now been accepted in Canada and around the world as the leading process for recovery of gold and silver, replacing the Merrill-Crowe process and thus removing the need for CCD thickeners or belt and drum filters. The overall design of conventional CIP adsorption circuits was established in the late 1970s and it has remained substantially unchanged until now. Most of the development work since 'hen has been concentrated on improving methods of separating pulp and carbon and on reducing carbon losses during transportation and agitation.Resin-in-pulp (RIP) has been used for many years in uranium mills in the USA. However, most of the plants were built in the 1960°s and RIP was only chosen when liquid-solid separation of leach pulps proved very difficult. The plants are far from ideal as they have high resin losses and high maintenance costs. Consequently, there is room for improvement.Davy McKee has taken a fresh look at the engineering development of in-pulp contactors leading to a fundamental redesign of the adsorption units. The improved in-pulp technology uses a modification of the proven air-swept screen techno1ogy together with a new technique of process operation. The new contactor operates at high pulp throughput rates with high concentrations of carbon or resin in the recovery stages, resulting in a significant reduction in the contactor size over conventional design. As a result of this reduction in the size of the contactor by up to 80%, significant savings can be made in equipment and building costs. In addition, the plant 1s easier to operate than a conventional CIP plant."

Jan 1, 1987

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-I993. Part I, presented in the June, 1994 issue of the CIM Bulletin, gave a listing of thesis titles. Part II. which consists of edited abstracts of theses considered to be of direct application to mineral deposit studies and exploration. is presented under various themes as follows:A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothermal Gold Deposits. Other Gold Deposits and Related Studies:E. Magmatic Nickel-Copper, Platinum Group Element and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;G. Diverse Hydrothermal Deposit,>, Sediment-hosted CopperDeposits and Mississippi Valley Type Lead-Zinc Deposits; andH. Uranium-related studies, Evaporites and Exploration Geophysics.Abstracts related to themes A to F were presented in previous issues of the CIM Bulletin, abstracts related to themes G and H are presented in this issue.G. Diverse Hydrotbennal Deposits, Sedimenthosted Copper Deposits and Mississippi Valley Type Lead-Zinc Deposits"

Jan 1, 1995

By P. Mattar

The geotechnical importance of studying fluid flow through porous media and soils in particular, becomes evident when dealing with groundwater movement in surficial geomaterials that can be initiated by hydraulic gradients that develop during construction activity, groundwater extraction, impounding of reservoirs and groundwater recharge during adverse climatic events. In a geotechnical context, rocks are regarded as virtually impermeable materials, with comparatively greater resistance to flow of water through their pore structure. The importance of the permeability of rocks comes to the forefront when deep geologic formations are used in geoenvironmental activities for disposal of hazardous and toxic materials. The permeability of the rocks encountered is of critical importance to these geoenvironmental activities since the movement or transport of the hazardous materials during their eventual release will be largely governed by the permeability characteristics of the geologic formation. The estimation of the permeability characteristic of geologic formations is a non-trivial exercise since the measure of permeability can be influenced by the scale at which the measurement is made. Regional-scale and borehole-scale estimates of the permeability can be greatly influenced by the inhomogeneities, including fractures, fissures, solution channels and other anomalies that are present in naturally occurring geologic media. These anomalies are considered to be site specific and can only be determined in a reliable fashion by either conducting tests at the appropriate scale or in the regional-scale through inverse analysis of tracer movement patterns in rock masses. The estimation of the permeability of intact units of a geologic medium has important geoenvironmental applications in connection with storage of wastes since the units in which repositories will be located should be sparsely fractured and the sealing of the fractures and fissures are a prerequisite to developing an efficient solution for storage. The intact permeability of geomaterials is therefore regarded as an important property that influences efficiency and reliability of geoenvironmental solutions for deep geologic disposal. The permeability of geomaterials such as concrete and cementitious grouts are also important to many geoenvironmental and infrastructure applications where durability of structural materials in general and cements used for sealing deep boreholes and other access shafts employed in waste management endeavours is influenced by the permeability characteristics of these materials

May 1, 2009

By D. L. Johnston

"The avenues and degree of participation by aboriginals in the Canadian minerals industry have changed significantly during the thirty years of the author's career in that industry.The typical 1950s cycle of mineral industry involvement of a local non-Europeanized aboriginal was as an individual employee. The employment relationship would begin with the best of intentions by both parties of permanence and terminate when the pioneering employee was unable to reconcile the attendance behaviour required by the employer and the social-sharing behaviour demanded by family and friends.Cominco Ltd. has been a mine operator and developer in the North since the 1920s. Cominco's early experiences with employment of non-Europeanized natives at the Con Mine in Yellowknife, Northwest Territories from 1938 to 1986 was a negative experience from both the employee and employer ends. A series of classic failures in employment of individual aboriginals was a large part of the history. A few Metis or natives from other areas were the permanent aboriginal employees at Con (2010). Racial prejudice was overt on the street in Yellowknife and, it can be assumed, in the workplace, as well.The history of aboriginal employment at the Pine Point, Northwest Territories operation (1964 to 1988) was somewhat better but also frustrating. The mine was equidistant (80 km) from the Dene communities of the Hay River Indian Reserve and Fort Resolution, both on Great Slave Lake. Despite a large aboriginal presence and many well-intentioned efforts, employment of aboriginals at Pine Point never got much beyond ten per cent. These would have been half local and half northern prairie aboriginals. One continuing success story was the railcar loading and covering crew led by Ed McKay, a local aboriginal. This predominantly aboriginal crew did its own recruiting and several are on Cominco pension."

Jan 1, 1995

By Paul M. Lévesque

The Dome Mine has been in production for nearly 100 years and throughout the years many different mining methods were used to extract the ore. An exploration program late in the 1990s outlines new resources requiring the mine to extract the rock and some previously placed backfill (alluvial sand and/or classified tailings). It is therefore imperative to separate the backfill from the rock to reduce the negative impacts of handling the backfill on the ore pass, crushers and mill processes. Separating the backfill from the ore at the source would also reduce and/or eliminate the cost of handling this waste stream. The paper will touch on the backfill removal criteria, the risks, the alternatives and the selected method, screen decks, for backfill removal at the Dome Mine. The 155549 bulk zone case study will illustrate how the screen decks are in use at the mine. The paper will also illustrate how the lessons learned and conclusions of the work done for the 155549 bulk zone were applied to the second screen deck installation for the 257260 bulk zone.

May 1, 2009

By Wei Ye, Lei Li, Xianjian Guo, Feng He

The purpose of the paper is to study the smelting process of copper concentrate with high Cu/S ratio produced in Africa or other areas around the world and theoretically analyze the influence of slag type on the smelting process. The paper has compared the processes used successfully in smelters, including CAPEX and OPEX and other factors, to provide reference for the industry to select the best process under specific conditions. INTRODUCTION At present, a great amount of copper concentrates with high Cu/S ratio, with chalcocite being the major source of copper, have been produced or are about to be produced in the Copperbelt in Africa and other countries in the world. The copper concentrate is usually high in copper (~30–55wt.%) and low in sulfur (~10–15wt.%). The conventional processes of smelting-converting and roasting-leaching-electro-winning for treating this type of concentrate is high energy and materials consumption such as electric power\fuels\flux et al. The direct-to-blister (one-step) smelting process can be considered favorable due to a reduction in processing steps. Up to now, there are four copper smelters in the world operating with the direct-to-blister smelting process. There certainly are problems in the process such as high copper content in the slag, strict operation requirement of slag cleaning electric furnace, etc. Except technical issues, the impact of factors on economical aspect such as power and material cost needs to be considered comprehensively in process selection. In this paper the technical issues of direct-to-blister smelting process, including slag treatment process, were analyzed and the comparison to the conventional processes and economic analysis of direct- to-blister smelting process to treat high Cu/S ratio concentrate were done.

Jan 1, 2019

By A. Navarra, Norman Toro, T. Marín, Fernando Ayala

The quantitative techniques to evaluate the enhancement of a particular unit operation should consider the corresponding changes to the adjacent unit operations. For example, the expansion of off gas handling capacity should consider the corresponding changes in converter cycle times, matte grade, and other operational parameters, that can provide the optimal system-wide benefit. In general, the upgrading of smelter equipment is risky due to the size of capital investment, as well as any unforeseen impacts on rest of the operations. However, this risk can be mitigated by applying the principles of Front End Loading (FEL) in the formulation of multiphase re-engineering projects. The initial phases of engineering are relatively inexpensive, and determine whether or not to pursue the subsequent phases that are comparatively more expensive. Each phase of engineering depends on increasingly detailed descriptions regarding the critical phenomena that can effect design decisions; the increasing levels of detail may result from numerical simulations, as well as laboratory and plant trials. The quantitative framework should be sufficiently flexible to accommodate these increasing levels of detail, regardless of the particular phenomena, so that it may evolve throughout the project. The current article describes the combined usage of mass balancing, thermochemistry and multiphysics, in the development of discrete event simulation (DES) and finite differences (FD). The incorporation of finite differences into a DES framework depends on adaptive time-stepping, to determine threshold-crossing times, e.g. when the matte temperature surpasses a critical level that necessitates the addition of cold charge. The hybridization of DES and FD is appropriate for multiphase smelter development projects, as it supports semi-continuous material flows, operational policies and scheduling, as well as unexpected events and trends, in increasing levels of detail. This type of framework will support the installation and tuning of modern control systems, including state-of-the art sensors and machine learning algorithms.

Jan 1, 2019

By Eric D. Marks

Fatalities resulting from ground workers colliding with objects and construction equipment accounted for approximately 18% of the total construction fatalities experienced in 2010. Current injury and fatality measuring methods have proven to be inadequate due to their use of passive measures of safety rather than a more active approach, such as the use of leading indicator data (also called near misses) of hazardous proximity situations between ground workers and heavy equipment on construction sites. The objectives are to create and evaluate the effectiveness of a reliable algorithm for collecting and analyzing the resulting leading indicator data from hazardous proximity situations. Numerous experiments emulating typical interactions between workers-on-foot and heavy equipment are used to evaluate the proximity sensing and detection technology. Safety leading indicator data (also called near misses) generated by the proximity sensing and detection technology during the experimental trials are used to create and assess the resulting algorithm. Results from the experiments indicate that leading indicator data generated from these systems can be processed and analyzed to identify hazardous proximity situations and incidents on construction sites.

Aug 1, 2013

By T. Crivits, I. Bellemans, V. Cnockaert, K. Verbeken

It is well known that slag foaming can significantly complicate copper smelting processes. This is especially true for unpredictable events that generate large amounts of slag foam during a small period of time. These events are here referred to as eruptions and are typical for certain types of liquid bath furnaces such as modern top submerged lance (TSL) furnaces. A few authors already made the link between over- oxidation of the slag phase and slag foaming. In this work, the mechanism is studied in more detail and explained using the smelter chemistry and the behaviour of dynamic foam formation. Finally, the most influential parameters on the foaming behaviour of the process are presented. INTRODUCTION Copper remains one of the most important metals used in our modern society. In 2017, the annual amount of copper produced worldwide was about 23.5 million metric tons. This makes copper the third most produced metal in the world after steel and aluminium. The majority of this copper was produced by copper smelting, about 19 million metric tons, both from primary concentrate and secondary feed material as reported in ICSG’s World Copper Factbook 2018. In the past, copper smelting was mainly performed using Flash smelting, a technology developed before 1949 (Kojo, Jokilaakso & Hanniala, 2000). Nowadays, this type of smelter is being complemented by other smelter types such as ISASMELT and Ausmelt technologies. These are two types op smelter furnaces, based on the concept of a top submerged lance (TSL) furnace. These two technologies were both commercialized around 1990 (Arthur & Hunt, 2005). It is estimated by Wang et al. (2016) that at this time, both flash and TSL smelters contribute equally to the total amount of annually smelted copper. Flash smelting stays the most important technology for extracting copper from primary sources. TSL furnaces, on the other hand, are more suited than Flash smelters for the recovery of copper from secondary materials. This is because of the different ways that the feed material is inserted in both furnaces. In Flash smelters, the ore and fluxes needs to be fine and completely dry in order to be able to blow the mixture inside the burner area of the furnace. The feed material for TSL smelters show less constrains concerning humidity and particle size. The material is dropped from the top inside the molten bath. As a result, a more complex and flexible feed stream can be processed using TSL smelting (Wood, Hoang & Hughes, 2017). This feature will become more important in the future as primary copper sources gets more scarce and the need for a fully sustainable material cycle increases.

Jan 1, 2019

By M. Mahdi, L. So, A. MacMillan, D. Metcalfe, J. Woloshyn, D. Sauter, N. Uys, JP. Janse van Rensburg

For city smelters, with limited real estate, efficient slag cleaning furnaces followed by water granulation to produce an iron silicate product is the preferred process approach. Water granulation, however, consumes large volumes of water and requires high maintenance due to abrasive slag/water slurries. Air granulation offers an alternative to water granulation, which eliminates water use and has low maintenance requirements. Although full-scale operation has not been implemented for copper slags, full-scale operation for platinum group metal (PGM) converter slag has been implemented. A review of full-scale air granulation performance for PGM converter slag is provided. Based on PGM converter slag granulation performance, parallels to copper slag granulation are drawn and full-scale operation for copper slag is modelled using computational fluid dynamics (CFD). INTRODUCTION Typical slag management practices in the copper industry include dumping, slow air cooling, and water granulation, as shown in Figure 1. Dumping is the most commonly used slag handling method for most metal production plants, but presents challenges including the requirement for a large slag pit, requirement for expensive/high-maintenance “hot” mobile equipment, risks associated with transportation of molten slag, and no value recovery from slag as a sellable by-product or from slag as a source of heat.

Jan 1, 2019

By Ian S. Thompson

"Exploration properties form a continuum from grass roots to those with favourable geology, geochemical and/or geophysical anomalies, mineralization, showings (prospects), and finally to those with defined mineral deposits. Often properties exhibit a composite of these categories.The most problematic to value are properties or deposits that are not economically exploitable at the time of the valuation, due to a lack of exploration, insufficient grade or tonnage, poor mining conditions, or the imposition of socioeconomic, environmental, or legal constraints.Various acceptable methods of valuing the range of all such mineral properties or deposits are reviewed. Some inappropriate methods are also discussed.BIOGRAPHYIan S. Thompson is President and Principal of Derry, Michener, Booth & Wahl Consultants Ltd. (DMBW), an independent consulting practice, specializing in exploration, ore reserve estimations, engineering and valuations of mineral properties.Mr. Thompson is a graduate in Honours Geological Sciences from the University of Toronto with over 35 years Canadian and International experience in mineral exploration and development, including the discovery of base metal. gold and uranium deposits.DMBW is affiliated with DMBW, Inc. in Colorado, and works with independent engineering and financial groups in North America, Europe, Australia and Africa.Mr. Thompson is a national member of CIM; the Associations of Professional Engineers of Ontario and British Columbia; The Geological Association of Canada; The Society of Economic Geologists; The Prospectors and Developers Association of Canada and the BC and Yukon Chamber of Mines.INTRODUCTIONThis paper is presented in response to the request of the Mineral Economics Society of the Canadian Institute of Mining and Metallurgy for a Review of Approaches to Valuation of Mineral Properties, as recommended by the TSE/OSC Mining Standards Task Force.Exploration properties with undeveloped mineral resources range from grassroots acreage without exploration history, to those containing mineralization (or a mineral resource) that is insufficiently explored, to well explored deposits which lack either continuity, or sufficient grade/tonnage, or have poor mineability or metallurgy, such that they are not currently exploitable at the time of the valuation. This does not imply that they do not have value."

Jan 1, 2003

By Jaroslaw W. Drelich

Despite the success of DLVO and extended-DLVO models that have been developed for homogeneous and smooth surfaces, a vast majority of practical surfaces encountered in mineral ore beneficiation are typically rough at various scales; they are also typically heterogeneous. The interactions of gas bubbles with particles having rough and heterogeneous surfaces are much more complex than the commonly used DLVO or extended-DLVO models predict. The effects of surface roughness on flotation and colloidal interactions have been reported many times in the past, although a clear understanding of their origins has been lacking. To explain differences in colloidal interactions for spherical hydrophobic particles, a theoretical analysis of the interaction potential was carried out for a model rough particle interacting with a bubble surface in an electrolyte solution in this study. The attractive hydrophobic interaction potential was added to repulsive retarded van der Waals and repulsive electrical double layer interaction potentials. The rough microscopic particles were modeled as spheres decorated with nano-sized asperities. Parameters that reflect common flotation separation systems were selected for testing this theoretical model and computation of the energy barrier applicable to particle – flat bubble surface interactions. It was found that hydrophobic asperities with the height of only several nanometers can reduce the repulsive interaction energy by an order of magnitude. Theoretical analysis also reveals that surface coverage of microscopic particles by nano-sized asperities is important as well. The findings of this research suggest that manipulating and engineering the particle surface topography could lead to better control over flotation separation.

Jan 1, 2016

By T. Sugawara, H. Sekimoto

Electrorefining of low-grade copper alloys containing various amounts of nickel, lead, antimony, bismuth, arsenic, selenium, silver, and gold in sulfamic acid media was demonstrated. The copper concentration of the alloys used as an anode was 70–90 wt%. The electrolyte contained 100 g L-1 of free sulfamic acid and 40 g L-1 of cupric ion. Galvanostatic electrolysis was conducted at 200–300 A m-2 in the electrolyte using a low-grade copper alloy anode and a stainless steel cathode at 25C. The terminal voltage was approximately 0.8 V at the start of the electrolysis, although it increased periodically to approximately 2.0 V and then shortly returned to its initial value. Nickel, lead, and arsenic from the anode dissolved in the electrolyte and were removed. Antimony, bismuth, selenium, and silver were removed as solids. Consequently, a dense copper cathode was obtained, and the concentration of copper was evaluated by inductively coupled plasma – optical emission spectrometry to be 99.82–99.99 wt%. INTRODUCTION Electrorefining of copper is conventionally carried out in a sulfuric acid electrolyte using crude copper assaying at 99.5 wt% Cu as the anode (Biswas & Davenport, 1994). Elements more noble than copper do not react anodically, and consequently, they are distributed in anode slimes. Elements less noble than copper dissolve from the anode. Nickel and arsenic are stabilized as aqueous species. Lead, antimony, and bismuth react with water, sulfuric acid, or arsenic acid to form barely soluble compounds; thus, they are distributed in anode slimes. An emerging issue in the electrolytic refining of copper is an increase of impurities in crude copper used as the anode (Moats et al., 2013). This is due to an increase in the content of impurities in copper concentrates as well as an increase in the types of secondary copper feedstocks (e.g., E-Scraps, automotive shredder residues, and smelting residues) treated in the copper pyrometallurgical process. An extreme case is a copper smelter that does not use copper concentrates as feedstocks. In such a process, copper-bearing feedstocks are smelted in a top submerged lance furnace to prepare low-grade copper alloys assaying at 80– 90 wt% Cu (Sekimoto et al., 2013). Such low-grade copper is not acceptable as an anode in the conventional copper electrolytic refining process because it is easily passivated during electrolysis. Consequently, electrolytic copper is produced by leaching the atomized low-grade copper in a sulfuric acid solution with oxygen, followed by electrowinning. However, electrowinning should be avoided whenever possible because the electrical energy consumed in electrowinning is 5–10 times higher than that consumed in electrorefining. Therefore, the development of technologies for electrorefining of low-grade copper alloys is desirabl.

Jan 1, 2019

By Robert B. Parsons

"Draft income tax amendments aimed primarily at certain carve-out arrangements prevalent in the oil and gas industry could have devastating results for long standing royally arrangements in the mining industry . Whether or not this potentially damaging effect is intended is largely beside the points-the point is that the mining industry would be well advised to become familiar with the draft amendments and make sure that the potential damage to existing and future royalty agreements is minimized.The draft amendments fail to take into account the nature of mineral royalties and app ear to reflect a lack of understanding of the characteristics of the mining industry.IntroductionOn July 19, 1985 Finance Minister Michael Wilson released draft amendments to the Income Tax Act which are intended 10 effectively thwart the use of so called “carve-out arrangements"".Unfortunately, the proposed amendments are so broad and far- reaching that countless ""innocent"" royalty arrangements in the mining industry, and in the oil and gas industry, are threatened. The potential harshness of the new rules would be compounded by the retroactive application to the amendments to longstanding royalty and similar agreements."

Jan 1, 1985

By Simon Pelletier, Jose Delgadillo, Dave Page, Pramod Kumar, Raj Rajamani, Dilek Alkac, Martin Fillion

"In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal’s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned.First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized."

Jan 1, 2012