Search Documents

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By Madaah Hosseini H. R., P. Abachi, S. Miraghaei

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled powders are much higher than those of corresponding Fe-Si bulk alloys with a minimum at 13.5 at.% Si. The values of coercive force decreased after annealing but it seams that the residual strain developed during milling is not the major contributing factor to the higher values of coercive force in the mechanically alloyed powders and nanocrystals behave as single-domain particles without exchange interaction between them.

Jan 1, 2006

By Nirmal Weerasekara

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By S. Fahland, P. Vogel

"The Gorleben salt dome has been investigated since 1979 for its suitability as a repository for the disposal of high-level radioactive wastes. The geoscientific surface exploration was followed by underground exploration of the site beginning in 1983: underground excavation work included the sinking of two shafts from 1986 to 1994, the excavation of the infrastructure area and of drifts located in the first exploration area EB1 within the following years. The exploration was interrupted for ten years from 2000 to 2010 as part of a moratorium. After the expiry of the moratorium in March 2010, the geoscientific underground exploration at the Gorleben site was resumed. The investigations were interrupted again in autumn 2012 due to a political decision. The exploration programme included extensive geoscientific investigations: geological exploration, geophysical investigations, mining exploration and mining observation, laboratory tests, in-situ geotechnical measurements, geological modelling and numerical model calculations. To analyse and interpret the results of the in-situ measurements and mining observation geomechanical, thermal and thermo-mechanical model calculations were carried out. One of the main elements of the in-situ geotechnical investigations were high-resolution geothermal measurements performed in boreholes used for geological exploration and geotechnical tests.The geothermal measurements are used to evaluate several geotechnical findings, e. g. drift closure, rock deformation, stress change, and are completed by thermal model calculations to analyse and interpret the results of in-situ measurements and mining observation. The model calculations have been carried out using the special purpose JIFE code. To consider the whole exploration mine with the adjoining host rock as well as the successive excavation of drifts and boreholes in detail a three-dimensional finite-element model was developed. The model calculations are used to analyse the cooling-off of the surrounding rock of the drifts caused by ventilation. The cooling-off of the surrounding rock is an ongoing process affecting the results of further geotechnical measurements in the near field of the drifts. To predict a realistic time and space dependent distribution of the temperature field of the host rock within the exploration area which is influenced by ventilation thermal model calculations are necessary. Comparing the calculated temperature field with the in-situ determined rock mass temperature field within the exploration area EB 1 the results show a sufficient agreement. Furthermore there is very good correspondence, both qualitatively and quantitatively, between the experimental and the calculated findings regarding the temperature profiles including the effects of excavation and ventilation of the drifts."

Jan 1, 2015

By T. Sakai

Present authors have succeeded in single pass large draught rolling of AZ31 and ZK60A magnesium alloy sheets below 200 °C without heating rolls by raising rolling speed above 1000 m/min. Heavy reduction larger than 60% can be applied by single pass high speed rolling even at room temperature. The rolled sheets showed fine recrystallized microstructure by dynamic recrystallization. The improvement of workability at lower rolling temperature is due to temperature rise by plastic working. In high speed rolling, almost all of the work done by plastic deformation is converted into the heat that raises the temperature of the sheet during rolling because the heat did not flow out of the sheet by conduction and radiation within very short time.

Jan 1, 2006

By Chunfeng Zhao, Chong Bao, Cheng Zhao, Jiashen Tian, Matsuda Hiroshi

"Based on digital image correlation (DIC) method and self-developed code, the global strain field changing and failure properties of rock-like materials with pre-existing double flaws are experimentally studied under uniaxial compression. By theoretical analysis with linear elastic fracture mechanics (LEFM), the strain approach proves to be practicable to investigate cracking process. Thus, two types of process zone are defined to discuss the specimen’s coalescence evolution at different loading stages. Crack initiation, propagation, and coalescence is a process of zone development and nucleation. DIC strain field results are studied on a meso-level using a strain approach. In the shear coalescence mode, the SPZ (shear process zone) in a bridge area coalesces with each other, while the TPZ (tensile process zone) grows independently. In general, the paper tries to establish the link between microscopic mechanical mechanisms and macroscopic mechanical responses in flawed rock. Further research should be done to study the cracking process and its effect on rock strength in detail by the DIC method.INTRODUCTIONNatural rock contains discontinuities including pores, fractures, inclusions or other defects. The existence of these discontinuities in the rock can decrease the strength and stiffness of the rock and they are a source of initiation of new discontinuities which may in turn propagate and link with other cracks and further decrease the strength and the stiffness of the rock (Sagong & Bobet, 2002). Lots of theoretical, experimental and numerical researches have been done in studying crack initiation, propagation and coalescence in rocks (Hoek & Bieniawski, 1965; Kranz, 1983; Reyes & Einstein, 1991; Park & Bobet, 2009; Gonçalves & Einstein, 2013). But when it comes to multiple pre-flaws, the issue that how the preexisting flaws affect each other becomes complicated and uncertain. The stress field around the tips of flaw can either enhance the impact of single flaw or weaken it. According to the observations have been done before, it is found that the way and function in which these cracks propagate and coalescence depends on the geometric arrangements (Bobet, 1997; Bobet & Einstein, 1998; Wong & Chau, 2001)."

Jan 1, 2015

By A. E. Aho

"The Pacific Nickel property lies 7 miles northwest of Hope and 100 miles east of Vancouver, in the Coast Mountains of southwestern British Columbia. Nickel-copper sulphides were discovered in ultrabasic rocks on this property in 1923 and the deposits were explored by Pacific Nickel Mines until 1937, then again between 1951 and 1954 by Pacific Nickel Mines and by Newmont Mining Corporation through its subsidiary,Canadian Ore DepositsWestern Nickel. The property was studied by C. E. Cairnes (1) in 1924, by W. E. Cockfield and J. F. Walker (2) in 1933, by H. C. Horwood (3), (4) in 1936 and 1937, and by the writer in 1951 and 1952. Except for a few thousand tons for trial shipments, the property has never been mined. Indicated ore reserves now total somewhat over one million tons averaging about 1.4 per cent nickel and 0.5 per cent copper, with lesser values in precious metals and cobalt.GEOLOGIC SETTINGThe nickeliferous ultrabasic rocks form part of the core of a 15-milewide block of Late Palæozoic metamorphic rocks and Mesozoic intrusives which extend north-south between the coast batholith of British Columbia and the Chelan batholith of Washington. Margins of this block are faulted in part against less metamorphosed volcanic and sedimentary rocks largely of Jurassic and Lower Cretaceous age (Geo/. Surv., Canada, Map 737 A, 1942). Serpentinites, suggestive of deep transgressive structure, occur within the block, and also at its east margin along faults which are southern extensions of the regional Yalakom-Fraser River fault zone. Some of the other mineral deposits in the Hope area appear to be spatially related to these major faults.The mineralization at Pacific Nickel occurs almost exclusively within a stock-like mass of ultra basic rocks which mingle with, and partly cut, a larger batholithic mass of genetically related diorites and norites of late Mesozoic age (Figure 1 ). The ultra basic mass consists essentially of fresh, medium-grained hornblendic pyroxenite with peridotitic cores and with a remarkable margin of pegmatitic hornblendite. The most hornblendic rocks appear to be chiefly products of reaction and replacement of the pyroxene and olivine rocks. The mineralization consists of disseminated and massive pyrrhotite, with subordinate pentlandite and chalcopyrite, amongst fresh olivine, bronzite, and, Jess commonly, augite and hornblende. Both the ultrabasics and mineralization are cut by small hornblenditic and dioritic dykes, and by veins and alteration zones."

Jan 1, 1949

By J. B. Yianatos, F. A. Contreras

Mineral carrying rates across the pulp-froth interface in the range of 1.4-3.2 tph/m2 and bubble surface coverages between 7 and 22 %, have been determined in large rougher flotation cells operated under normal conditions. To evaluate these variables, measurements of bubble size distribution, bubble load and size distribution of particles collected by true flotation, were performed at different concentrators. A model for estimating the bubble surface coverage at the pulp-froth interface level as a function of bubble load, Sauter mean bubble diameter and particle size distribution of the mineral collected by true flotation, was developed. Bubble loadings in the range 24-70 kg/m3, bubble sizes between 1.5 and 3.2 mm and superficial gas rates between 1.2 and 2.0 emfs, were measured in copper rougher flotation cells under normal operating conditions. Estimated bubble surface area fluxes were in the range 31 to 62 cm2/s/cm2- Results of carrying rates and bubble surface coverage, at the pulp-froth interface, were significantly lower than the maximum carrying rate for the collection zone, indicating that in this case is difficult to achieve maximum carrying rate at the pulp-froth interface level. The main constraints regarding carrying capacity limitations are then related to the froth transport characteristics (i.e. cell design, froth residence time, froth stability, froth recovery). Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By G. M. Ross, I. M. Ross, J. A. Scott

"The otherwise waste heat in many water streams in the mining industry can be used to provide space heating of adjacent infrastructure including laboratories, workshops, and offices. This can be achieved by using heat pump systems, which can work as a replacement or in conjunction with existing space heating. In the example investigated—process cooling streams at an ore smelter—the analysis provided illustrates that annual heating costs can be 19% lower and a simultaneous 62% reduction in CO2 emissions can be achieved.RÉSUMÉ Dans l’industrie minière, la chaleur qui serait normalement perdue des circuits d’eau pourrait servir à chauffer des structures adjacentes incluant les laboratoires, les ateliers et les bureaux. Cela pourrait se faire en utilisant des systèmes de thermopompes, qui pourraient remplacer ou s’ajouter au chauffage existant. Dans l’exemple étudié, des circuits de refroidissement de procédé à une fonderie, l’analyse fournie illustre qu’il est possible de réduire les coûts annuels de chauffage de 19 % et d’obtenir une réduction simultanée de 62 % des émissions de CO2."

Jan 1, 2016

By J. M. Harrison

"The Nor-Acme gold mine is near the shore of Snow lake, northern Manitoba, about 75 miles east of Flin Flon. The claims that form the nucleus of the present property were staked in 1927 by C. R. Parres, but it was not until 1941 that diamond drilling disclosed the potentialities of the deposit. In that year a large-scale drilling programme was begun under the direction of F. Ebbutt, of the Howe Sound Exploration and Development Company. Two orebodies were outlined containing about 5,000,000 tons of ore assaying $5.25 in gold per ton. In August, 1945, construction of the mining plant was begun.All information and interpretations contained in the following brief description of the deposit were obtained from surface mapping.GEOLOGYThe ore lies at the contact between a coarse, basic, pyroclastic rock, which is the hanging-wall, and grey, acidic lavas and sediments, which form the footwall. These rocks are cut by irregular basic intrusions that vary in composition from diorite to hornblendite, and by small acidic dykes . Tourmaline is locally common in the hanging-wall rock near the ore.The ore occurs in brecciated, silicified, and ·slightly carbonatized rock. Arsenopyrite is the main sulphide and the gold is associated with it. Pyrrhotite is locally abundant and minor pyrite, chalcopyrite, sphalerite, galena, and cubanite have been noted. Two orebodies are known, the Dick and the Toots. The Toots, which is much the smaller of the two, is about 1,000 feet west of the Dick."

Jan 1, 1954

By G. G. Bowser

THE time has come when, as your President, 1 turn the helm over to my worthy successor. When 1 was reminded by our Secretary that 1 had to prepare an address for this meeting, 1 was at a loss for a subject. In the hope of inspiration 1 perused the records of our Society for some years past. 1 found in these records that many problems in need of solution relative to industry in Nova Scotia were discursively dealt with and that sound thought was given to the solution of these problems, with a natural leaning, of course, to problems pertaining to the mining industry. 1 found also that some of the reasoning was remarkably prophetie. Some of these subjects and problems were: The use of pulverized coal to generate power instead of hydro-electric power; rural electrification; the importance of youth training for an efficient place in industry; the proper marketing of coal; the fuels competing with coal; the need for better in-dustrial relations between employer and employee; better education for success in the social field as applied to industry; and Canadian unity. The issue of some of these copies has been forced upon us by war. For instance, there appears to be no marketing problem for coal, nor does there ? seem to be a marketing problem for anything just at present. The problem of the coal producer just now is supply and transportation. Also, at present, coal fe.ars no competitors, such as oil-and not even hardwood. Many large companies now have an industrial Relations or Personnel Manager and department. Furthermore, we have been compelled of necessity to train our young men, and women also, for both industry and war. However, war does not solve these problems and, with the return to normal times, we may be faced with the same troubles in even greater measure. My reason for mentioning these copies is to point out that, as mining men, we are aU desirous of progress in every industry, not only the mining industry; and that mining men are able to see clearly ahead. In normal times, especially in matters not directly affecting the mining industry, we are inclined to let matters take their own good rime, or let the government do it. We do not seem to realize that these necessary and desirable changes can be made in times of peace-instead of being forced upon us by war or other social upheavals-by the method of sound thought and action to the desired end.

Jan 1, 1943

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By Didier Fohlen

Three Policy Shifts to enhance IFC?s Accountability ? Comprehensive and dynamic treatment of social, health, safety and environmental risks ?Covers a range of risks encountered by clients in emerging markets ?Framework to anticipate risks and to address them as they arise ?Includes community development, biodiversity, human rights ... ? Effective principles to guide an outcomes-based approach ?By clients and IFC ?Focus on broad community support and value-added sustainable development initiatives Enhanced governance, transparency and disclosure

May 1, 2006

By D. R. Murray

"In 2017, Nutrien Allan Potash remediated a portion of the concrete liner in the production shaft. A set of underslung work platforms and collection boxes were used in conjunction with hydraulic splitters, jackleg drills and hand chippers to excavate and remove the broken concrete. New concrete was placed with the original pressure relief design, using a shaft slip form. Shortly after excavating, it was found that the estimated breaking rate and amount of original concrete in-situ was under estimated. Fifteen feet of excavated concrete (2719cu.ft) and ten feet (of replaced concrete was completed on April 28, 2017, and operation of the production shaft was returned to mine operations. During February 2019, Nutrien Allan Potash began remediation of a portion of the concrete liner in the service shaft. The project is different than the 2017 project, as the remediation has occurred during normal running operations and occurred only on night shift. Rather than hydraulic splitters and hand chippers, the new method includes a concrete saw and mechanical excavator from a working platform. The selected method is based on the lessons learned from the 2017 project in the production shaft. The service shaft project was scheduled to be completed in July, 2019. INTRODUCTION Nutrien Allan Potash is located approximated 75 km east of the city of Saskatoon, Saskatchewan, Canada. There are currently two shafts at Nutrien Allan Potash: the Production Shaft and the Service Shaft, transporting people and material from surface to a depth of 3,335 ft. The Production Shaft was completed in 1967, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1605 and 2037 ft Levels. A second set of cast iron tubbing was installed in the Duperow formation between 2203 and 2463 ft Levels in 1999. The remainder of the concrete as of todays standards is designed as a pressure relief liner. The Service Shaft was completed in 1968, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1600 and 2048 ft Levels. A second set of cast iron tubbing was installed in 1981, with 169 ft installed through the Duperow formation. The remainder of the concrete as of todays standards is designed as a pressure relief liner. PRODUCTION SHAFT REMEDIATION During the second quarter of 2015, the Mine Engineering team were notified of an area of concern in the production shaft. The shaft specialists of Golder Associates Ltd (Golder, formerly Alan Auld Canada) were contacted to complete an inspection of the production shaft liner with emphasis on the area of concern. Based on the inspection and documentation review, it was determined that the concrete at the 2804 foot elevation had been broken out for some time and was retained with #8 rebar bolts with resin encapsulation. The broken concrete was encroaching on the clearance to the conveyance."

Jan 1, 2019

By A. C. Hawken, L. M. Strah

"The Report outlines the Conversion to Rubber Mill Liners and steel grinding balls from the old style Cobalt pocket liners and flint pebbles which had been used in 5'x22' Fraser-Chalmers tube mills for over fifty years. An outline of the past history and some of the plant modifications are mentioned as well.The details pertaining to considerations, modifications and repairs carried out on the mills are described. Factors influencing the rubber liner design are outlined along with the description of the rubber liner design.The performance and advantages to date are given and concludes with brief summary.HISTORYThe original amalgamation-cyanidation mill of Dome Mines Limited went into operation in 1912. Milling has been continuous since 1912, except for two periods; one of 17 months commencing in December 1917, and the other of about 12 months, when fire destroyed the plant in November 1929. Initially the capacity of the mill was 350 tons a day. In 1916 it was raised to 750 tons a day, following which there was a gradual expansion to 1,500 tons a day."

Jan 1, 1977

By Zhiye Zhao, Jianping Sun, Zhipeng Xu

"The subsea rock cavern project is an underground storage facility. For cost-effective and safe excavation, the risk caused by the groundwater seepage into the rock cavern must be addressed. As one of the essential steps of the assessment work, the hydraulic conductivities of the fractured rock masses should be reliably determined based on the limited measured data and geological information from the few boreholes. On the basis of site investigation data and monitored water flow and water pressure data during excavation, this paper presents an estimation method for hydraulic conductivities of the rock masses containing water bearing zones.INTRODUCTIONIn the development of underground rock caverns/tunnels, the uncertainty of hydro-geological conditions plays a critical role in terms of construction cost and construction safety. Excessive groundwater seepage has been identified as one of the key safety factors which always lead to vast loss, such as the Seikan Tunnel in Japan which encountered sudden water inflow and then catastrophic face collapsing, tunnel flood during excavation (Xu et al., 2013). As a key factor in the risk management associated with the groundwater leakage into rock cavern, the hydraulic conductivity determination is very important for cost estimation, reliable water control and construction management.The case presented in this paper is an underground project consisted of a cluster of rock caverns/tunnels for storage of hydrocarbon products. These caverns are located in heterogeneous sedimentary bedrock, at a depth of 130 m beneath a basin, and the crowns of caverns are located at about 100 m below the sea bottom. The caverns/tunnels are designed at two levels, the water curtain tunnels are at the upper level, and oil storage caverns are at the lower level, as shown in Figure 1. A number of horizontal and vertical water injection holes drilled from the upper water curtain gallery tunnel will establish continuous horizontal and vertical water curtains for providing a stable pressure distribution around the caverns, to keep oil/gas inside the lower storage caverns. As the hydrostatic pressure of groundwater around the storage caverns is higher than the pressure of stored oil and gas, the stored oil and gas will not leak out of the cavern (Lu, 2010; Xu et al., 2015). Groundwater pressure gauges are installed in the water curtain gallery tunnels, and water from the operational and access tunnels is injected continuously into the curtains to maintain the pressure. Some monitoring data are recorded at different construction stages. This paper proposes suitable methods to predict the hydraulic conductivity in rock mass and to determine the hydraulic conductivity in the water bearing zones."

Jan 1, 2015

By R. F. Neider, W. R. Bain

"Expanding upon one aspect of a recent paper on ""Fluid Column Roasting at Sherbrooke Metallurgical Co. Ltd.,"" the present paper deals with the operation of the fluid column process to achieve substantial elimination of cadmium and lead during the roasting of pelletized zinc concentrates. Designed to meet the need for additional feed for Matthiessen and Regeler Zinc Company's vertical retort zinc smelter in West Virginia, without recourse to a sintering operation, the plant is capable of simultaneously attaining very low lead and cadmium levels on demand, through operation in the manner described. Fluidizing air admitted via the wind box is supplemented by natural gas admitted via a tuyere bank 15 ins. above the hearth, in quantities adjusted to maintain a reducing atmosphere within the interstices of the bed. In addition, careful attention is paid to bed temperatures, which run from 1,080° to 1,100°C. Under these reducing conditions, 90 per cent of the cadmium and 92 per cent of the lead in the feed are eliminated, the sulphate sulphur content is decreased by 0.5 per cent, sulphide sulphur is held at 0.6 to 0.08 per cent, and the zinc content correspondingly in-creases. The fuel value of the natural gas is recovered as extra steam, which carries a credit. There are some added difficulties with fume accretions, gas conditioning and gas -cleaning, some of which have yet to be overcome."

Jan 1, 1967

By Horatio Sam-Aggrey, Margot Hurlbert

Small Modular Reactors (SMRs) have been touted as having the potential to spearhead a nuclear renaissance. Proponents of this view cite the relative advantages of SMRs over larger nuclear plants as reason for their optimism. Some of these merits include potential economies of mass production deriving from modular factory production, enhanced safety features, the ability to locate reactors in remote areas, and reduced requirements for technical workforces to install and maintain SMRs. Despite the optimism surrounding SMRs, nuclear power is still a contentious issue for many Canadians. The growth of nuclear power remains adversely affected by concerns over issues such as: the health and safety consequences of nuclear power generation, environmental impacts, proliferation of nuclear materials, terrorism, and radioactive waste disposal (Organisation for Economic Co-operation and Development (OECD) and Nuclear Energy Agency (NEA), 2010). Personal values, past nuclear accidents, and lack of trust in the industry are other factors influencing attitudes toward nuclear energy (IAEA, 2005). In Canada, three main areas where SMRs could be used have been identified. These include: a. Traditional, on-grid power generation, especially in provinces looking for zero-emissions replacements for CO2-emitting coal plants. B. Remote off grid communities that currently rely on diesel or fuel oil power generation. There are 279 off-grid communities in Canada, many of them being Aboriginal communities (NRCan, ND). Notably, all communities in each of Canada’s three territories qualify as remote. C. Resource extraction sites, such as mining and oil and gas extraction sites. Many of Canada’s principal producing mines and active mineral exploration projects are located within close proximity of Aboriginal communities. Any proposed implementation of small nuclear plants would, require the support of the local population, which is largely Indigenous in the northern regions. The possible deployment of SMRs raises important issue relating to consultation and accommodation of Aboriginal concerns regarding potential SMR deployment. This is especially pertinent given Canada’s pending implementation of the provisions of UNDRIP. One of the provisions of UNDRIP that has attracted a lot of attention is the one on Free Prior and Informed Consent (FPIC). Drawing on previously published information, this paper discusses some of the challenges posed by FPIC for the deployment of SMRs. The next section outlines the provisions of FPIC and its implementation in the Canadian context. Section 3, details some of the challenges posed by FPIC to the deployment of SMRs, while Section 4 provides some concluding comments.

Jan 1, 2020

By James A. H. Church

This paper is in the nature of a protest against the dangerous propaganda afoot for the prevention of new mining undertakings and which is based on the imaginary 'blue ruin' conditions supposed to exist in the industry. An article by Mr. G. R. Pratt, A.M.E.I.C. in the first issue of the Western Canada News, February 2nd, 1925, and entitled "Review of Coal Mining in Alberta", is an excellent example of this type of propaganda. The article is a tissue of misstatements, faulty deductions and erroneous conclusions. For instance it contains the statement that some coal measures in Alberta are mined at great depth - whereas we all know that there is no coal mined at great depth anywhere in the province; another error is the classification of all mines under one head irrespective of whether they are mining prospects, 'country banks', or pukka mines equipped with railway facilities; and I believe that suppressio veri is tantamount to suggestio falsi. The bulk of his article hinges on a Table 1, which shows the details of coal produced in Alberta during 1923. Studying this table Mr. Pratt, in the manner of a conjurer producing rabbits from a hat, offers the following for the confusion of the public:- (1) "Waste effort, want of capital, waste of coal resources which result from unrestricted development"; the fact being that the waste is due to the failure of the Department of the Interior to exercise the powers which are inherent in the form of lease.

Jan 1, 1925

By Shugang Li

Coal and coal-bed methane are valuable energy resources. If they can be extracted simultaneously and safely, the triple purposes of mine safety production, new energy resource supply and environmental protection can be fulfilled. After mining, the mining induced fissure distribution feature and methane delivery behavior in overlying strata were closely related to the relieved methane degasification. Using physical simulation and numerical simulation, it was explained that the distribution feature of mining induced fissure was the Elliptic Paraboloid Zone (EPZ) in three-dimensional space. Based on the key stratum theory, the types, parameters, characteristics and dynamic evolution behavior of the mining induced fissure EPZ were analyzed. Applying environmental fluid mechanics and the mass transfer theory, the relieved methane floating-diffusion equation of the EPZ was established, and the corresponding transport process was analyzed. Using the field practice of relieved methane degasification in Tianchi Coal Mine, it explained that the mining induced fissure EPZ was the storage and delivery area of relieved methane. The degasification effect will thus be useful if the drainage system is laid in the EPZ. Such studies can provide the theoretical basis and technical support for the safe simultaneous extraction of coal and methane.

Aug 1, 2013