Search Documents

By L. Voisin, K. Mühlenbrock

A new pyrometallurgical process is proposed for cleaning complex copper matte and for recovering copper from copper scrap containing lead. In the process, a given amount of pig iron is added to the complex material under a reducing condition to produce two or three liquid phases at the equilibrium, depending on the content of sulfur in system, of copper-rich and iron-rich alloys, and matte, respectively. The novel process is proposed based on the experimental results obtained by performing laboratory scale tests in an electrical furnace at 1473 K followed by a quenching method on the final stage. The samples obtained from the experiments were analyzed by using Atomic Absorption Spectroscopy (AAS), Inductively Couple Plasma (ICP) and Carbon Infrared Spectrometry (CIS) techniques. The results were discussed on the basis of the distribution of lead as impurity in the miscibility gap where equilibrated phases coexist. According to the mass balance calculations, the elimination of lead into the iron-rich alloy phase as a harmless and smaller deposit might be feasible and the process proposed for cleaning the complex matte would be promising.

Jan 1, 2014

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By R. Vracar, D. Sinadinovic, Ž. Kamberovic

The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions aiming to get products with favourable technological characteristics from which precious and other useful metals can be recovered. A high partial oxygen pressure (1.5 MPa to 2 MPa), high leaching temperature (190°C to 200°C), pulp density 80 g/L to 240 g/L, ore fraction size 76 µm and leaching time up to 4 hours yield good results in rich ores. The full extent of copper and zinc conversion as well as a high extent of iron conversion has been achieved, while lead, gold and silver and a minor part of iron remain as a solid residue among gangue minerals.

Jan 1, 2001

By Terry A. Lee

The grade of mineral resource estimates underpin all major economic considerations of mining prospects. While there are reporting requirements to satisfy when stating a mineral resource estimate, an examination of NI 43-101 style reports suggests that authors believe that there are a number of ways of addressing these requirements. As a reader of these reports, some processes are helpful and others are not so in getting a real appreciation of how realistic is the mineral resource estimate. Critical to the quality of the mineral resource estimate is how realistic is the economic mineral concentration component. In many cases, this parameter is called grade. The industry experiences increased difficulty in achieving realistic grade estimates as the sample grade variability increases. The level of transparency in a mineral resource estimate is very much a function of the competence of the author. An objective presentation of the critical data, such as grade sampling variability can assist a reader in determining if the geology of the mineral concentration is adequately understood and how realistic is mineral resource grade estimate. This paper has considered 75 NI 43-101 style reports released in the past 2 years. The review demonstrates features that were helpful in determining how realistic the mineral resource grade estimate is. If there is insufficient transparency in a report, there is a high probability that the mineral resource grade estimate will not be realistic.

Apr 1, 2005

By C. Jewell, G. H. Rupay

"67 - 2:15-3:00Regeneration of Hydrochloric Acid from Waste Pickle Liquor Using a Fluidized Bed Reactor System. G. H. RUPAY and C. JEWELL, Dominion Foundries and Steel Ltd., Hamilton, Ont.The disposal of acidic waste liquors from pickling processes has always been a problem for the steel industry. With increased awareness toward environmental control and the problems acidic wastes create, processes utilizing recovery and regeneration of the waste acids are becoming more popular. This paper describes the Keramchemie/Lurgi process for regenerating hydrochloric acid from waste pickle liquor using a fluidized bed reactor system. The process parameters are outlined, together with a brief description of the equipment. This is followed by a discussion of the operating problems and concludes with economic data."

Jan 1, 2000

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, 'longwall' and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By C. Peña, C. A. Zaror, M. Bustamante, M. Vega

The goal of this paper is to present the carbon footprint of Chilean cathodic copper, as a function of the electricity generation mix, ore grade, and process efficiency. Ore grades and acid leach-solvent extraction-electrowinning (LX-SX-EW) yields in the range 0.5-1.0% and 60-80%, respectively, were considered here. Additionally, electricity supply from two Chilean suppliers, SING (1.0 ton CO2/MWh) and SIC (0.4 ton CO2/MWh) was assessed. Simulation results show that oxide plants located in northern Chile, served by the SING network, feature carbon footprint within 4.3 - 11.4 MWh I ton cathodic copper, as compared with 3.5 - 9.3 MWh I ton copper in plants served by SIC. The footprint was found to increase as ore wade and process yields decrease.

Jan 1, 2011

By A. T. Jakubick, A. MacG. Robertson

This paper reviews key issues related to the placement of dry (soil) covers on extremely weak, compressible fine tailings. The design and construction of soil covers on such tailings often presents a formidable challenge to the geotechnical as well as the environmental engineer due to the low shear strength, poor traffic ability, and high settlement of under consolidated tailings at the time of reclamation. The geotechnical issues to be considered include: (1) consolidation of near-surface tailings to achieve strength gains, improve traffic ability, and allow safe placement of initial cover layer; (2) stability of tailings slopes during dewatering of tailings ponds and/or cover placement; and (3) long-term settlement of tailings and its impact on cover integrity and final surface shaping. The environmental issues to be considered include: (1) management of contaminated (free) pond water; (2) management of contaminated pore water expelled during tailings consolidation; and (3) management of (uncontaminated) surface water on top of the cover. This paper summarizes recent experiences gained in a large uranium tailings reclamation project. It is concluded that a careful consideration of both geotechnical and environmental issues during the planning stages greatly reduces the costs and environmental risks associated with fine tailings reclamation.

Jan 1, 2000

By Simon Houlding

"The objective of Part J of this paper is to identify the limitations of the traditional modelling methods and to illustrate, by example, the potential for error created by their application to complex deposits and mining situations. Part 2 describes the evolution of new, proven technology which eliminates these deficiencies and provides precise and practical alternatives. These promote the use of realistic geological and mining shapes and eliminate altogether the rectangular approximations of traditional methods.The Case for Precision ModellingIt is not the intent of this paper to promote the benefits of computer modelling per se. It is assumed that these are recognized by the mining industry in general. The concern of Part 1 is to identify, qualify and quantify (where possible) the limitations of the tractitional modelling methods. In many instances these methods continue to be applied to complex geological and mining situations for which they were never intended nor designed. The source and magnitude of the resulting errors, conflicts and inefficiencies are not always obvious, however, they can have far-reaching effects on the efficiency and profitability of mining operations.The conclusions support a rapidly growing demand by industry for practical, precise modelling technology which eliminates the deficiencies and can be applied with confidence to evaluation, design, planning and control of mine production in all situations. Part 2 describes new technology which has evolved in response to these industry pressures and has already been successfully applied to complex mining situations. This new technology can aptly be described as appropriate technology for the 1990s."

Jan 1, 1991

By L. Rosato

In the past decade, as a result of increasing iron loads, Canadian Electrolytic Zinc (CEZinc) has become a pioneer in understanding the critical factors that affect the roasting of concentrates with high pyrite contents as well as those factors governing the effects of high iron loads on the leaching circuit. De-bottlenecking efforts in the roaster and acid plant section of CEZinc have given rise to a better appreciation of the impact of iron on roaster productivity. High standards for impure solution quality, zinc recoveries and residue disposal have all led to an increased comprehension of the limits of the leaching circuit and the optimization potentials with respect to iron and ferrites. In this paper, the impact of iron on the roasting and leaching circuits of CEZinc will be reviewed and special emphasis will be given to some of the more recent process optimization and improvement activities.

Jan 1, 2006

By M. Al-Khawaja, F. Hassani, F. Mucciardi, N. Razavinia

"In today’s economy many industries are becoming aware of the need to recover some of the waste heat they create. Industrial processes release, on a global scale, over 100 tera-Joules (i.e. 1014 J) of waste heat annually. The recovery of waste heat can lead to a reduction of greenhouse gas emissions and it can also provide a financial benefit which can be obtained by converting some of this excess heat to electricity. At McGill, a research program has been initiated so that low grade waste heat (temperature between 100ºC and 300oC) from process off-gases found in pyro-metallurgical industries is captured and concentrated by using heat pipes and then converted to electricity by a mechanical engine. This paper illustrates the 3 C’s process (capture, concentrate and convert waste heat to electricity). It also provides some preliminary experimental data. INTRODUCTIONThe problematic climate change caused by the use of fossil fuels, the rapid depletion of global reserves and the catastrophic consequences of nuclear power generation call for renewable and safe, resources of energy, for both man and the environment. Extensive researches in the production of energy from renewable sources and improvements in efficiency of current technologies can help us to reverse this trend.The greatest advantages of using renewable energies are that they don’t deplete and they also contribute to a green environment. On the other hand the disadvantage of using these resources is that the energy available from renewable sources is much less concentrated than that provided by fossil fuels and nuclear energy. This makes renewable energy less attractive for large scale industrial uses in most cases. A key target for society for the 21st century is the production of energy from renewable sources at a cost that is competitive with fossil fuels. Fossil fuels represent a concentrated form of energy; usually it is referred to as high grade energy. Nonetheless, there is a vast supply of alternative energy. The sun, wind, water and biomass were the first to be explored. While these are all valid options that warrant concerted efforts and large investments, there is another source of energy that typically is produced by manufacturing industries. This energy is often referred to as low grade waste heat. Most of this energy is simply vented to the environment through the stream of off-gases. In the future it will be necessary to capture and convert some of the low grade heat to a valuable form such as electricity if we are to improve on the efficiency of energy usage."

Jan 1, 2012

By D. A. Stokes

"In October of 1980, Fording's 15 000-ton capacity clean coal silo was put into operation. The silo was unique in that it was designed to allow the mass flow of material, coupled with a sophisticated computer-controlled dynamic loadout/weighing system.On May 1, 1982, an explosion, attributed to a methane buildup, devastated the top of the silo. .As a contingent plan to minimize the effect of the production loss the conveyance to the silo top was reconstructed and the silo' was back in operation by mid-June 1982, although the silo top was left open to prevent further methane buildup. As dust emissions occurred during loading ofthe silo, an extensive study was undertaken to establish dust control for the silo, while at the same time providing methane detection and control.The study, conducted for Fording by the Cambrian Engineering Group of Calgary, involved an extensive search and investigation of existing coal silos. The study concluded that there IS no universally accepted method of controlling methane emissions in coal silos.The study also produced a unique conceptual design for handling methane, while at the same time, protecting the environment . Fording's Clean Coal SiloThe silo, located at Fording Coal's Fording River metallurgical coal operation, is utilized for the storage and load out of cleaned thermally-dried metallurgical coal.The silo was constructed in 1979 and 1980 to reduce unit train loadout times and to facilitate the handling of “special shipments"" of coal. The silo went into operation in October 1980, under manual control and utilized computerized, automated loading by February 198I.The silo is 21 m in diameter and 76 m high, with a nominal capacity of IS 000 live tonnes. The coal storage portion of the silo is 21 m in diameter and 48 m high, utilizing 2 steep-angled hopper outlets allowing mass flow of the stored coal during train loading. Each hopper has a control gate and a discharge chute, one chute for bulk loading, the other for trim loading of coal into the rail cars."

Jan 1, 1986

By F. Sorenson, P. A. Castellarini, F. Garbarino, M. N. Garcia

"Recently, significant efforts to improve productivity from the tight intervals of the Mulichinco Formation within the Sierra Chata Field in the Neuquén Basin have been ongoing. Because conventional high quality reservoirs were being developed in this field, a proper reservoir understanding and completion approach was applied. After developing these high permeability reservoirs, the operator began evaluating the tight intervals and new areas within the field, but a completely different approach was necessary to achieve motivating production improvement.An extensive study to help enhance reservoir understanding and identify key factors controlling productivity of these tight intervals (which tend to be in the range of 5 µD) has been ongoing. Some of the issues discussed in this study are 1) petrophysical review, 2) rock properties calibration, 3) geomechanics understanding, 4) faulting and micro faulting/lineaments description, 5) stimulation and completions review and, 6) understanding key production drivers.As in many other tight reservoir projects, a considerable area of the reservoir must be effectively stimulated during the hydraulic fracturing process to achieve economic productivity. Two critical issues hinder these objectives. First, the low permeability in addition to a pore pressure close to or even lower than hydrostatic are critical characteristics when attempting to flow back the well and clean up fractures. Second, very high horizontal stress anisotropy resulting from a strike slip stress regime promotes the generation of simple planar bi-wing fractures. It is well-known that this fracture geometry will contact much less reservoir area compared to more complex fractures, as the operator would normally intend to create at very low permeability reservoirs.This paper discusses these issues and how they were addressed. A pilot drilling and completion program was initiated during 2012 to validate this study. Key factors include well location relative to formation unconformities, their orientation relative to the far field principal stresses, hydraulic fractures generated, and overall completion design."

Jan 1, 2015

By Sang-Kyun Woo

The electric power conduit (EPC) in Korea has been constructed since 1978. Facing the challenge of safety and sustainability of the EPC, it is urgent to develop an inspection strategy and maintenance system for the structure based on the concept of life-cycle management. This paper introduces the newly developed mobile inspection and diagnostic system of the EPC. The novel aspect of this particular system is the integration of non-destructive mobile inspection techniques with BIM (Building Information Modeling) and LBS (Location-Based Service). BIM is an ideal tool and platform for developing an inspection and diagnostic system, and RFID (Radio Frequency Identification) is a useful tool to construct USN (Ubiquitous Sensor Network) for LBS. The goal of this research is to establish an EPC inspection and diagnostic system concept based on BIM and LBS using RFID. In this research, a BIM model of OPENTBM tunnel for EPC will be established to show the integration of 3D CAD with the inspection data. An EPC?s maintenance database, which includes the deterioration types of the structure, inspection records, and repair methods, was designed to interact with the BIM. The system will be implemented by the BIM with the related database, in which the construction geometry and all related information are stored. The proposed system was designed to utilize the inspection and diagnostic system under the USN environment using RFID in EPC directly.

Aug 1, 2013

By Geo. E. Cole

A GREAT deal of time and energy is now being devoted to the study of post-war reconstruction and rehabilitation, in spite of the fact that as yet we have not won the war in which we are presently engaged. If you feel that the study of post-war problems takes our thought away from the problem immediately before us, you may well query, "Well! What has all that to do with winning the war, our most urgent problem today?" The answer has been given by Principal James of McGill University, Chairman of the Cabinet Committee on Reconstruction: "Reconstruction is something which must be thought of in advance, partly for the purpose of recognizing exactly the influence of war-time activities, controls, and regulations on the post-war Canadian scene. Many people are acutely interested in this great problem. It is not that they are not interested in the war itself, or epochal events that are taking place from day to day. They have a vision of that future which they hope will be Canada's, and this vision inspires them to even greater efforts at the present time". The trend of events would indicate that changes, economic and industrial, after this war will be greatly out of line with those that followed previous wars in history, for the present struggle has involved every nation in the world. In the peace that will come, every engineer will have a task in bringing the most desirable order out of the most distressing chaos. We certainly are living in a changing world; we are witnessing geo-graphical and economic readjustments that no other generation in world's history has ever witnessed. And there is an opinion gaining strength in our Dominion, as in other lands, that after this war we shall live in a world in which our process of thinking and our very way of life will have to undergo drastic changes to cope with the new order of things. Sadly our world of today has had to revise the sublime vision that nation shall not lift up sword against nation, while salvage operations continue to beat ploughshares into tanks and the peaceful pruning-hook into a weapon for the deviltry of the commando.

Jan 1, 1943

By Michael Zurowski

This paper traces the history of International Mogul's assessment program on the Lake Ainslie barite-fluorite deposits of Cape Breton Island. The geology of the area is outlined, and the main vein systems described. The geophysical and geochemical exploration techniques employed are explained, the metallurgy of the ore is covered, and the market prices and economics of operation are described.

Jan 1, 1972

By R. Pressacco

"IntroductionAgrium’s history in fertilizer production and marketing goes back to 1931. Today, Agrium Inc. is a world leader in the production, distribution, and marketing of fertilizers and related products to the agricultural industry. Agrium is the largest North American producer of nitrogen fertilizers, a major producer of phosphate and potash fertilizers, and a world leader in fertilizer wholesale distribution and retail marketing. The mine at Kapuskasing is located some 40 km southwest of Kapuskasing, Ontario (Fig. 1). It has been developed to supply high-quality, low-cost phosphate rock to the company’s Redwater, Alberta facility, where it is an ingredient in ammonium phosphate fertilizer production. The Kapuskasing mine is the only phosphate mine in Canada and will rank as one of the highest-grade phosphate mines in the world (Clark and Duncan, 1999). Apatite is the principal ore mineral mined at the Kapuskasing Phosphate Operations.GeologyThe first record of exploration in the area was from a program executed by Continental Copper Mines in 1955 which evaluated the magnetic anomaly located in the Cargill and Cumming townships for its base metal potential. Intermittent exploration of the base metal potential of this magnetic anomaly continued in the following years, until the phosphate potential of the area was first examined in 1974 by International Minerals Corporation which recognized the presence of a layer of apatite sands overlying the carbonatite host rocks.The local geology consists of a core complex of multi-phased carbonatite rocks which are surrounded by a ring of pyroxenite, and have provided a U-Pb age date of 1907 Ma ± 4 (Sage, 1988). These two rock types are in turn situated within quartz diorite gneisses that form a large portion of the Kapuskasing Structural Zone (Fig. 2). The carbonatite host rock is sub-divided into two sub-types: sovite and rauhaugite. The sovite is a medium- to coarse-grained, white, banded rock in which calcite is the dominant carbonate species and it includes accessory minerals such as phlogopite, magnetite, clinohumite, apatite, olivine, pyrrhotite, and amphibole. Apatite can reach 15% abundance in this rock type (Sage, 1988). In sharp contrast to the sovite, the rauhaugite appears as a massive, fine-grained, dense, beige to tan-coloured rock in which dolomite is the dominant carbonate species. Phosphate values can range to 14% P2O5 in the rauhaugite."

Jan 1, 2001

By Yu-Min Cheng

Over the past two years, the construction industry has increasingly recognized the benefits and capabilities of building information modeling (BIM) for information integration, visualization and parametric design, reducing the duplication of work and complexity of interface integration, while significantly saving both time and cost. However, due to the variety of participants in engineering projects, the differences between data definition, data format, and data storage increase the difficulty of integrating data from diverse sources. Therefore, buildingSMART has developed a common data schema, called Industry Foundation Classes (IFC), that makes it possible to hold and exchange relevant data between different software applications, to increase the efficiency of BIM work and to ensure a consistent and high-quality output. This paper presents a novel methodology that assists in facilitating the import and export process for parametric BIM objects between heterogeneous BIM systems. This methodology is based on the IFC data schema and includes graphical and non-graphical description data. The objective is to retain the geometry, parameters, unit, texture and links of an object during exchange and sharing to ensure that data integrity is maintained. To sum up, this research addresses the issues of transferring parametric BIM objects between heterogeneous systems to increase data integrity and reduce transfer and integration times.

Aug 1, 2013

By Rob Boom, Yasuyuki Tozaki, Greg Traquair

The objectives of the business case are to examine a proposed metallurgical project and answer fundamental questions about project feasibility, risks, opportunities, and value. A business case fulfills these basic functions: estimates economic value; helps to understand competitiveness; serves as a risk management tool; and serves as a communication tool. A business case evolves with the project life cycle, and supports the gate reviews at the end of each phase of engineering, through to project construction and operations. A business case must be holistic, including all elements of scope that can impinge on project risk and value.

Jan 1, 2015

By Z. Abbasloo, A. Masoomi, L. Ebrahimi, A. Mortazavi, A. Keshavarz

"Investigation and 3D analysis of Heap no. 2 of Meydook copper complex was the subject of this study. In this project all geological and geotechnical investigations conducted in the mine were evaluated aiming at determination of Heap no. 2 design parameters. The main objective of the project was to evaluate the potential for construction of Heap. No. 2 on a waste dump built in a valley in the north side of the pit.Considering the space limitation for dump location this was a viable alternative to reduce the costs associated with heap no. 2 construction. Moreover, it allowed for a significant reduction in overall mining costs. Considering the project condition, a 3D analysis of heap major structures including; valley rock foundation, waste dump, and low grade ore was carried out. Five sets of analyses were conducted and the displacement and stress fields were calculated within the heap no. 2 components. In all analyses conducted the subsident profile was determined for the valley base rock and heap foundation (waste dump). Moreover, the shear interaction between heap and waste dump was evaluated at the heap interface. The analyses results showed that the maximum settlement at the heap base is about 4-5 cm and the waste dump provides a safe and reliable base for heap construction. Moreover, the analysis results showed that the selected %5 grade for the heap interface is good and does not pose any risk in terms of heap Interface shear displacements. A sensitivity analysis of heap mechanical parameters was also conducted. The obtained results show that if the friction angle of heap material is reduced below 25 degree due to acid spraying process, the heap walls become unstable and the heap geometry must be redesigned."

Jan 1, 2015