Search Documents

By F. Ajersch, A. R. Hekmat

Apparent viscosities of hypo-eutectic (Al-7% Al) and hyper-eutectic (Al-35% Si) binary alloys were measured in the semi-solid state using a Couette type viscometer at variable shear rates. Analysis of the microstructural evolution demonstrates the differences in the rate and degree of attrition of the primary phase particles which are characteristic of the thixotropic nature of the semi-solid alloy. It was observed that the Si primary phase in the hyper-eutectic alloy is much more difficult to fragment than the dendritic a-Al phase in the hypo-eutectic alloy. For the case of the a-Al, the dendritic structure is broken down by attrition and fracture of the dendrite arms whereas the fracture of the Si hexagonal crystals in the hypereutectic alloy occurs along the {100} and {110} cleavage planes. Results are presented for fixed solid fractions of the primary phase at isotherm condition for each type of alloy.

Jan 1, 2006

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

By M. Girard, C. Farsangi, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel Project: a copper and nickel deposit in Nunavik, Québec. The nickel and copper concentrates are filtered by plate and frame filter presses, and are transported 100km north to Deception Bay by truck. As the site is situated in the far north, extreme weather can be detrimental to production: roads can close for significant periods of time, resulting in the concentrator using all its storage capacity. During the winter of 2017, this accounted for over 100 hours of unplanned mill downtime. Different solutions to this problem were evaluated and the most economically viable combination of solutions was determined to be the use of concentrate storage containers and upgrading the plate size of the existing nickel filter press. By satisfying new, increased utility requirements, the cycle times would not change, but produce 30% more filter cake. Simulations were developed to determine the number of concentrate containers needed in conjunction with the upgraded press to eliminate unplanned downtime due to road closures and secure production through the winter. This paper summarises these simulations, the commissioning and start-up of the upgraded filter press, container loading procedures, and how this was put together to achieve a record 2018 winter season with a 90 percent reduction in downtime. The payback period of the project was 4 months. A specialised side-tipping trailer emptied the containers during the fall of 2018.INTRODUCTION The Nunavik Nickel Project is a nickel/copper mining project located in Nunavik, Québec. The nickel and copper concentrates are stored in stock tanks after thickening and are then filtered by plate and frame filter presses at the concentrator before being transported 100km to the shipping port at Deception Bay by trucks. The region is prone to periods of extreme weather during the winter, with winds that can reach +100km/hr and blizzards that severely limit visibility. The roads to Deception Bay are often affected by this weather, causing closures that last an average of 18hrs and as long as 72hrs. Additionally, there is a 15% chance that road closures occur within 24hrs of the last event. This has been an issue for the concentrator team since start-up in 2013, causing unplanned mill downtime every winter (Table 1) due to filling concentrate storage capacity during prolonged closures of the roads to Deception Bay."

Jan 1, 2019

By B. F. Osborne

"A new sensor cannot be considered in isolation from the process in which it is utilized. This paper, describing an on-stream particle size analyzer, therefore gives considerable emphasis to the slurry handling techniques employed to ensure that the instrument is presented with a representative sample. A new sampler is described, which continuously abstracts a small, representative sample from a closed pipeline containing a flowing slurry. This sample is then diluted, thoroughly mixed and pumped to a head tank, from where a continuous stream is fed at a constant rate to the size analyzer. Data are presented to show that particle size segregation is minimal throughout this sampling and sample preparation. A continuous particle size analyzer based on a separation principle is described, and the basic parameters of size distributions, and how they relate to this particular instrument, are considered. Typical results are given. An electronic system is presented which accepts the basic sensor outputs, and converts these to a particle size signal suitable for process control. Finally, the use of an inplant computer to process the sensor signals to obtain a particle size signal is briefly considered."

Jan 1, 1972

By J. F. Davis

Pegmatite dykes containing lithium minerals and beryl occur dose to the borders of intrusive masses of granitic rock in the Winnipeg River area of Manitoba. Both vertical and flat-lying dykes are present. Most of the pegmatites consist of zones, containing characteristic mineral assemblages, arranged more or Jess parallel to the borders of the dykes. Five important lithium minerals are present; each occurs in a separate zone, but all the lithium-bearing zones are situated toward the centres of the pegmatites. Spodumene is the most abundant and widespread of the lithium minerals and occurs as small crystals intimately intergrown with quartz. Beryl is not an important constituent of the lithium pegmatites, but when .present, occurs outside the lithium zones, toward the margins of the -dykes. Beryl is most common in dykes containing few or no lithium minerals. The mineral assemblage in the beryl zone of the lithium dykes is the same as that of the beryl dykes. The attitude and internal structure, particularly zoning, of the pegmatite dykes, and the texture and assemblages of the constituent minerals, have an important bearing on exploration, development, and mining of these pegmatites, and on the extraction of various mineral products from them.

Jan 1, 1958

By P. Karimi, A. Amini, H. Abdollahi, A. Mirzaeian

Due to detrimental effects of cyanidation process on the environment in gold industry, application of cyanide alternatives such as thiourea are being highly considered in recent projects. In this study, the extraction of gold from poly metal ore, using thiourea was precisely investigated. The representative sample contained 2.5 ppm Au and 160 ppm Ag. The sample was categorized as oxide gold ore, because the main part of its pyrite was changed to iron oxide and hydroxide such as goethite and lepidocrosite. According to mineralogy, the main gangue mineral was quartz. It shows that gold grains are free and interlocked with quartz matrix. Also, the presence of a high amount of silver in free and sulfide forms and also the low content of other sulfide minerals such as base metal sulfides is a remarkable point of these studies. In the gold extraction process with thiourea, there are several parameters that affect the rate of gold dissolution such as concentrations of thiourea as a gold lixiviant and ferric sulfate as an oxidant, pH and size fraction of feed and leaching time. The influence of these parameters on the gold dissolution rate were investigated and optimized. The results showed that the concentration of thiourea is the most influential parameter which could increase the gold recovery to 71% (at 10 g/kg sample). The optimal amount of ferric sulfate was determined as 6 g/kg sample. Also, the optimal levels of size fraction of feed and pH of solution were 88% under 75 micron and 2 as acidity; respectively. Leaching time was 6 hrs. In addition, this sample was leached with cyanide and the optimized values of size fraction of d88=75 microns, pH=10.45, 2500 ppm of sodium cyanide with time leaching of 24 hours were concluded for maximum recovery of gold in solution. Finally, the results of cyanidation tests were compared to the thiourea dissolution after optimizing all affected parameters in cyanidation process.

Jan 1, 2016

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By Song Mao, Local Joint Engineering Lab of Efficient Util of Dominant Mineral Resources from Karst Regions, Guizhou Key Lab of Comprehensive Utilization of Non-metallic Mineral Resource, Xianhai Li, Qin Zhang, unjian Ye, Guizhou University, Wei Cheng, Zhihong Liu

"Phosphate tailing is a kind of industrial waste that emitted from separation processing of phosphate ores, which is usually discarged to the tailing pond without treatment. Recovery of phosphorus from tailings is of great significance for comprehensive utilization of phosphorus resource. Chemical composition of a micro-fine cryptocrystalline phosphate tailing was investigated by X Ray Fluorescence (XRF) and Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), and mineral composition and occurrence of harmful elements were analyzed by optical microscope and Scanning Electron Microscope (SEM), X ray Energy Dispersive Spectrometer (X-ray EDS) and Mineral liberation Analyzer (MLA). On the basis of above, effects of those on mineral processing for phosphate tailing was analyzed. Chemical analysis results in combination with microscopy indicated that there is a certain amount of iron and aluminum and it should focus on the removal of them in separation processing. The cryptocrystalline structure, especially the micro banding structure and micro porphyritic structure indicated that there is quite amount of phosphate in fine particles and it should recovery the phosphorus as much as possible when designing the flotation technology for this difficult separation fine phosphate tailing. This study can provide theoretical guide for efficient phosphorus recovery of from fine phosphate tailing by flotation.INTRODUCTIONPhosphate rocks are vital nonrenewable resources and are essential components in agricultural fertilizers and phosphorous-based chemicals (Gharabaghi et al., 2009). About 95% of the phosphate produced around the world is consumed in the fertilizer industry (page 60 Abdel-Zaher, 2008; Jasinski, 2007). Froth flotation, a solid wettability based separation process is widely used in separation of phosphate rock and shown to be effective (Yehia et al., 1990; Singh et al., 1992; Elgillani and Abouzeid, 1993; Al-Fariss et al., 2013) .Poor selectivity and low recovery for micro-fine particles are hard issues in flotation of middle-low grade phosphate ore because Phosphate resources is becoming poor, fine and complex as the rich ores run out since the 1970s. The rapid depletion of high grade ores forces minerals industry to process low grade ores where finer grinding is required to achieve required liberation of the values, making the fine particle flotation inevitable. the performance of conventional flotation deteriorates rapidly as particle size decreases to below 10-20 µm, depending on the density of the particles (Feng and Aldrich, 1999). To date, fine particle flotation is still considered to be a challenge in mineral processing (Li et al., 2015) ."

Jan 1, 2016

By A. B. Carino

Gulf Minerals (Canada) Limited's Rabbit Lake uranium operation is located in the northern portion of Saskatchewan, 198 miles southeast of Uranium City and /34 miles northwest of Lynn Lake, Manitoba. The paper follows the ore flow through crushing, grinding, sulphuric acid leaching, countercurrent decantation, solvent extraction, ammonium diuranate precipitation, thickening, drying and tailing neutralization.

Jan 1, 1979

By J G. Brady

This paper discusses the ceramic products used in the construction industry in Canada, as well as the main raw materials used in their manufacture. The products include the! following: (1) clay prorlucts -such as facing brick (glazed and unglazed), common brick, facing tile (glazed and un-glazed), terra cotta, load-bearing tile, non-load-bearing tile, structural clay floor tile, quarry tile, drain tile, sew-er pipe, conduits .and flue liners -which are made mainly from domes-tic common clays and shales and from domestic or imported stoneware clays and low-grade fire clays; (2) floor and wall tiles of the whiteware type, which are produced from ingredients such as kaolin, ball clay, feldspar, nepheline syenite, talc, pvro-phyllite and wollastonite; (3) glass products -the major ones being sheet glass, plate glass and mineral wool (glass wool, and rock or slag wool) -which are made from such materials as silica sand, soda ash, salt cake, feldsspar, nepheline syenite, dolomitic limestone, high-calcium limestone. borax and (for rock and slag wool) various rocks or slags;

Jan 1, 1963

By Randolph A. Pax, Brian Cornish

The operation of grinding mills in an ore processing circuit is supported by monitoring the input and output variables. These can include the feed ore size distributions, ore feed and water addition rates. The outputs can include the discharge undersize density, oversize tonnage rate and the P80 of the discharge. The grinding mill performance is judged by the power draw, recycle rates and discharge grind size. Conditions inside the mill are inferred from loads cells or bearing pressures and past histories. An overall noise value is sometimes used to evaluate the load as well as the occurrence of excessive impacting of steel balls onto the liners/lifters of the mill. This paper presents results of the internal behaviour of a mill using non-contact stationary microphones located close to the mill outer shell (Pax, 2012). The noise generated by a mill can be attributed to a number of events that occur inside these mills and suitably analysed can provide real-time determinations of in-mill behaviour and can provide powerful insights into the operation of the primary comminution tumbling mills. The acoustically determined signals including a specific 'steel' signal, water hold-up, integrated area together with a classification of impact events. Specific results from case studies will show information of the trajectories inside a mill, steel to rock ratio as well as rheology effects. By incorporating a self-consistent understanding methodology for the in-mill processes from an array of microphones, the information can be used to diagnose the dynamic conditions inside a mill.

Jan 1, 2016

By T. T. Tigert

INTRODUCTION THE PURPOSE of this article on methane is to present the simple basic facts of the characteristics, detection, occurrence, and control of this natural gas in metal mines, so that operators and .safety men may deal with it with some degree of confidence. Fortunately, although methane has been noted at many metal mines throughout Canada, the occurrences usually are small flows of short duration, and the ignitions experienced have, in most cases, had minor consequences. However, methane does present a hazard that can be of serious proportions, and ?any complacent attitude toward this gas that might exist in the minds .of people engaged in underground mining operations should be dispelled when it is ,pointed out that, in Ontario alone, ignitions of this gas have resulted in at least four fatalities, and eight men seriously injured and burned, during the past three years. lt is well-known that liberation of methane can and does .occur suddenly, often in mines where no gas has been found before, and that many ignitions and explosions have occurred in so called non-gassy mines. In view of this, it is apparent that no mine can, with any degree of certainty, be classified as non-gassy. CHARACTERISTICS OF METHANIZ The characteristics of natural gas encountered in most of the Ontario mines indicate that methane is the chief constituent. Methane (CH4), commonly termed 'marsh gas', and by the coal miner 'firedamp', is a colourless, odourless, and non-poisonous gas considerably lighter than air, and is the explosive gas frequently found in coal mines. Its physiological effects, closely resemble those resulting from nitrogen.

Jan 1, 1951

By R. H. McMillan

A classification of important uranium deposits which utilizes both genetic and descriptive criteria is presented. The dual aspect is useful because, while the non-genetic nomenclature for the different deposit types is amenable to various interpretations, the critical characteristics of each deposit type can be analyzed to clarify various genetic points. Although the classification is intended primarily for Canadian uranium deposits, most of the important deposit types known elsewhere can be accommodated.

Jan 1, 1978

By D. Laguitton

"Mathematics, process theory, process practice and computer applications are the main disciplines that contribute to developing useful techniques for computer simulation of mineral and coal processing plants. As in any multidisciplinary effort, communication or transfer mechanisms must be developed to facilitate the flow of experience between participants of different backgrounds. These mechanisms include written reports, verbal communications, workshops and transfer of computer programs. The SPOC project at CANMET is devoted to computer simulation and as such has addressed, or will address in the near future, problems inherent to methodology transfer. The first major output of the project was the material balance program, MATBAL2, which has been acquired by over 30 organizations. Program documentation, industrial workshops and summer student programs have been used to effect the transfer. This experience is discussed and the future outlined.IntroductionComputer simulation has become a common tool in many different fields of human activity during the past two decades, as illustrated in Figure 1. The total number of articles abstracted in Chemical Abstracts under the general subject entry of “Simulation"" has been following a pseudo-exponential growth since 1972 and was approaching 5000 in 1980, whereas no such entry was even used prior to 1967. This represents over a dozen papers published daily on the subject and should continue to grow to higher figures. Still, progress toward accepting modelling and simulation in mineral and coal processing has been very slow. It will be shown later that this slow acceptance is a cause rather than a consequence of the limited success of the various attempts made so far to draw unambiguous benefits from simulation applications. The real cause of the difficulties in fully accepting the new methodology lies in the multidisciplinary aspect of modelling and simulation, which does not suit the traditionally conservative approach that prevails in designing and operating large and costly processing plants."

Jan 1, 1982

By R. K. Carnochan

MANY improvements have been made in recent years in the milling of industrial minerals and it is the purpose of this paper to review some of the more important innovations that are now being used in the preparation of these products. Some of the observations which will be made have been prompted by what was seen on a recent trip to industrial mineral milling plants in the north and central sections of the eastern United States. The flotation plants visited were those of the Valley Forge Cement Company at West Conshohocken, Pa., the International Agricultural Corporation at Mount Pleasant, Tenn., and the Aluminum Ore Company at Rosiclare, Ill. Besides these, sand plants in Pennsylvania, West Virginia, and Ohio, coal-cleaning plants in Pennsylvania, pyrophyllite, mica, feldspar, clay, and kyanite plants in North Carolina, and a zinc mill and the Tennessee Valley Authority ceramic laboratory in Tennessee were visited. The milling of industrial minerals can be considered under three broad headings, namely, crushing, grinding, and purification. Usually there is both a separation and grinding problem in treating an industrial mineral, but the problems are distinct, although sometimes a separation is made while grinding, as in the case of a Raymond throw-out mill, which grinds and at the same time throws out most of any hard material present in its feed.

Jan 1, 1939

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

By Marvin J. Udy

THE preparation of this paper is in response to many requests for in-formation on the mining and smelting developments which have been carried on for the past three years or more by the Chromium Mining and Smelting Corporation of Canada. By way of introduction, the following paragraphs, relating to the early history and present status of the chrome-mining industry in the United States, are of interest. They are quoted from Bulletin No. 76 of the California State Mining Bureau, published in August, 1918: 'Chromium was discovered about 1797 by a French chemist, Louis Nicolaus Vauquelin, in ore from Siberia. From that time until 1827, the Urals, in the region of Ekaterinburg, supplied the chromium used in . Europe. In the summer of 1827, as the historian advises us, Isaac Tyson, Jr., saw in a Baltimore market-place a cart containing a cider barrel, which was held from rolling about by some heavy black stones. He had made a study of such stones at the first-known American locality, the Bare hills near his father's home, six miles from Baltimore, and he recognized the black stones as chromite. On inquiry, he found the chromite came from the Reed farm in Harford county, 27 miles northeast of Baltimore. At this time, Tyson was one of the very few men in the country who knew the value of chromite, and in the next few years he took full advantage of this knowledge. He immediately bought the Reed farm. He found about 30 tons of float-ore on the surface, but there was no outcrop of ore in place. Never-theless, he sank a shaft, and at a depth of eight feet struck an ore-pocket which proved to be 80 ft. long, 25 ft. wide, and 8 ft. in maximum thickness. His next discovery was of placer chromite in the sands in the beds of brooks on an estate called Soldiers' Delight, 16 miles northwest of Baltimore. Thus far, Tyson's observations had shown him that chromite occurred apparently only in serpentine areas. His explorations were now leading him farther afield. In 1828, he found on the Wood Farm, in Lancaster county, Pennsylvania, a deposit of float chromite which led him to lease the ore-right of the farm, which he finally purChased in 1832. Here he developed the famous Wood mine, the largest single producer of chromite in the world.

Jan 1, 1938

By W. Zheng

Pipelines can develop stress corrosion cracks in either intergranular or transgranular form. Since the mid-1980s, numerous colonies of transgranular cracks have been found across Canada and many other countries in the world. While the intergranular form of cracking has been well studied in the past 40 years, the mechanisms governing SCC in near-neutral pH environment, i.e., the transgranular form of the cracking, are yet to be understood in greater depth. Over the past ten years or so, a large number of research publications have been available on this subject and this paper summarize our latest progress in understanding the mechanistic aspect of the problem. Better understanding of the role of mill scale surface and the steel metallurgy in crack initiation has been indicated in the recent literature. However, the initiation of SCC in the lab research still relies on loading conditions that are far more aggressive than those encountered in the field. Most crack growth studies in the past are also performed under very aggressive mechanical conditions, which could have prevented the observation of environment effects. However, more recent research at lower K or Delta K ranges seems to suggest a strong role of the environment. Naturally, modeling of growth should reflect the effect of the environment, steel metallurgy, and the changing mechanical properties of the pipe steel with time. For a specific steel in a given environment, the crack growth rates tended to increase with the strain rate, indicated either by the nominal applied loading frequency or by the calculated crack tip opening rate. Future research needs to address the issue of concurrent growth of multiple interacting cracks. More attention should also be given to concurrent initiation of multiple cracks in a colony, as failure is usually caused by a coalesced crack not by an individual crack. The effect of soil environment should not be limited to the chemistry of soil solution; other factors such as cathodic processes, the variation of environment with time and physical conditions of coatings should also be considered as part of the study.

Jan 1, 2005

By Selwyn G. Blaylock

I.-THE HISTORY OF THE SYSTEM TO trace the history of the development of the Co-operative Committee System in The Consolidated Mining and Smelting Company of Canada, Limited, one must look backward about twenty years. In 1915 and 1916, the first years of the W ar to really affect Canadian life, there were sixteen hundred men working in the Trail plant. These men were, on the whole, a splendid body of men and pa trio tic to the core. They were almost one hundred percent organized, ninety-five percent of them be-longing to the Union of the Western Federation of Miners. Most of the tradesmen belonged to their craft unions as well. For example, there were ? local machinist, steel workers', electrician, boiler maker, bricklayer, and carpenter unions. The Company had always maintained an open-shop policy and refused to enforce membership in any union, but recognized the right of every man to belong to unions. The only exceptions have been the I.W.W. and the One Big Union. Both of these organizations have always been fought by the Company. By 1916, membership in the Western Federation being practically 100 per cent, the Company recognized this organization's authority to make agreements, and a wage and hour agreement was drawn up and signed by the Company and the local officials of the Union, and ratified and signed by the Head Office of the Union in Denver, Colorado. This agreement was for the duration of the war.

Jan 1, 1936

By Mohamad Sabsabi, André Hamel, André Moreau, Paul Bouchard

"Laser-Induced Breakdown Spectroscopy (LIBS) is an atomic spectroscopy technique used to measure elemental concentrations. It is well-adapted to in-situ and in-line measurements during materials processing in general, and pyrometallurgy in particular. It is an optical non-contact technique and it can measure nearly all elements, including light elements. Our group has developed a mobile prototype system to measure molten metals. The system includes a tube, also called a lance, one end of which is immersed in the molten metal. An inert gas flows in the tube and bubbles out below the surface. The LIBS measurement is made through the tube and onto the bubble’s surface. This is done to avoid measuring contaminants, slag, or fluxes often found at the surface of the melt. An added benefit is that the molten surface is constantly renewed and thus, more representative of the bulk. An alternative to using our lance is to use a tuyère, such as a gas injection tuyère in a converter, as we did several years ago in a nickel matte converter. In this presentation, we will show various applications emphasizing more recent developments. This includes the simultaneous measurement of the concentrations of Cu, Ni, Fe, Co and S in molten matte at 1125 °C. The more obvious industrial applications of the technology include determining the best time to end oxygen blowing in the converter and elemental concentration measurement during alloying.INTRODUCTIONThe mining industry continually faces challenges in optimizing cost and productivity. Because of the large volumes of materials that are being processed, small improvement can have a big impact on benefits. Better real-time information can help improve this optimization."

Jan 1, 2016