Search Documents

By H. P. Pew

THE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by T HE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by 85 miles wide, is the largest in Canada in areal extent, in the amount of oil in place and in the current producing rate. The discovery well was completed in the middle of 1953. The field has grown until its present area is 369,820 acres. There are 74 working interest owners in the field. Early in the producing history of the Pembina field a committee of operators was formed on a permanent basis. The Pembina Operators' Committee has established a permanent staff, which compiles and distributes pertinent field information on a regular basis to all participants. The Alberta Oil and Gas Conservation Board has dealt with field-wide problems primarily through this committee. Expansion of the field was rapid as shown by the number of wells completed -from 135

Jan 1, 1961

By W. A. Gow, H. H. McGreedy

It is believed that many of the problems encountered in the operation of gold cyanidation plants are difficult to resolve due to the lack of sufficient and reliable in-formation regarding the variations and actual values of operating variables at any given time. The application of instruments to monitor the more important variables in the cyanidation process should result in more efficient plant operation and a better understanding of the process. The use of pH and conductivity sensing devices for alkalinity measurements, a monitor to determine the dissolved oxygen content of plant solutions, a continuous cyanide titrator and sonic control of grinding circuits are discussed. Although the discussion is oriented toward the cyanide process, much of the paper is applicable to other ore treatment operations.

Jan 1, 1966

By J. B. Mawdsley

"AbstractThe uraninite-bearing deposits in the Charlebois Lake area of northeastern Saskatchewan are unusual and important concentrations of uranium. They were first discovered in 1949 and preliminary development work to the end of the 1951 field season indicates the probability that this will become •another uranium producing district. The deposits are in zones bordering granite masses. These zones are of migmatite (mixed rocks) composed of calcium-rich meta-sediments intruded and replaced by a fine-grained white pegmatite. Locally this pegmatite is replaced by an end fraction which is relatively rich in fine-grained disseminated uraninite; it is these occurrences that constitute the bodies of economic interest.The fine-grained white pegmatite contains plagioclase feldspar more lime-rich than that in the granites of which it is an end differentiate. This extra lime, evidently derived from the intruded sediments, would result in the raising of the temperature of crystallization of the pegmatite-forming magma, thus consolidating it rapidly near the granite contacts as a fine-grained pegmatite. The end liquor containing uranium was evidently locally concentrated in minor fracture zones in these pegmatites. Where no lime sediments were present. the coarse-grained alkaline pegmatites were formed. Their crystallization would not be accelerated and the uranium would tend not to be localized in the pegmatite but to migrate and consolidate at lower temperatures with the end products, possibly in some instances as pitchblende veins."

Jan 1, 1952

By A. Warczok

Chalcocite concentrate obtained by magnetic separation and flotation of Bessemer matte is processed in the Inca top blowing bottom stirring MK reactor into semi-blister copper. The semi-blister is then converted into blister copper in the multi-purpose vessels (MPV) by oxidation of iron, nickel and sulphur. High melting point NiO and Fe30 4 are formed inside the MPV s, which together with Cu20 and smaller amount of fayalite are the major constituents of the solid mush. The accumulation of solid mush and buildup requires periodic MPV cleaning by adding reductant and copper-nickel matte, a unique process called "washout". Various reductants and their combinations, such as pig-iron, 15%Si Ferro-silicon and 50%Si Ferro-silicon, have been used for the reduction of solid mush and buildup. The possibilities of using calcium carbide as a reductant and slagging flux were examined experimentally at the crucible scale. The rate of reduction of MPV buildup was determined by continuous measurement of CO and C02 contents in the offgas and the flowrate of argon carrier gas. The rate of the buildup reduction with calcium carbide was approximately five times faster than the rate of reduction with coke. Additionally, the formation of CaO results in the melting of reduced buildup and formation of a slag at 1300°C and higher temperatures. It was found that simultaneous silica addition enhanced the melting and slag formation. The results showed the strong dependence of the reduction rate on temperature. Activation energy is approximately 225 kJ/mol. Expected benefits of using calcium carbide are related to cost saving on reductant, significant acceleration of solid mush reduction, and reduced amount iron input from reductant.

Jan 1, 2007

By D. E. Keeley

Introduction Gunite is a mixture of sand and cement applied to any surface by being shot by compressed air through a nozzle, where it is wetted just before leaving the orifice. The mixture is transported through a hose from a machine called a 'cement-gun'(l). Guniting of rock surfaces has been standard practice at the Mcintyre Porcupine Mines, Limited, for several years. Where used on walls and backs of cross-cuts; shaft stations, and other rock openings, as an air seal, gunite has eliminated the necessity of constant scaling to keep rock from falling from these places, and, under worse conditions, it has been used in place of timber supports. This has been of definite help in reducing costs, promoting safety, and minimizing fire hazards. During the past year guniting has been quite extensively used here in the rock head-works of the new internal shaft, No. 12, sunk from the 3,875-foot level. Gunite is at present being applied to the stations of that shaft well below a mile from the surface. This paper describes the method of guniting as carried out at the McIntyre, and illustrates how, by the adoption of this process, mining problems connected with scaling and loose ground have been completely solved. It is hoped that the information presented may stimulate discussion and assist in the use of gunite in this and other mines. The guniting method of applying cement was first developed by Carl E. Akeley (2), Curator of the Field Museum, Chicago, in 1907, and was exhibited in New York at the Cement Show in 1910. The museum was located in one of the old World's Fair buildings, built of roughcast and in bad repair. Mr. Akeley, who was a man of inventive nature, set about devising means of applying cement to repair the walls. The cement-gun was the result. Mr. Akeley was a taxidermist of note, a sculptor, and also the inventor of the Akeley camera. In his work, he was in the habit of using fast setting materials to build up foundations for statues, etc.

Jan 1, 1934

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

By M. Kermani

This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill has an alkali activator such as sodium silicate in its materials in addition to primary materials of cemented mine backfill which are deslimed tailings, water and binders. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. Initially, the influence of sodium silicate concentration on the mechanical properties of samples was evaluated using the unconfined compressive strength (UCS) test. Consequently, the effect of curing temperature on CHF and Gelfill samples cured in various curing temperatures ranging from 5?50 °C was studied using the UCS test. Microstructure of selected samples was studied wirth the mercury intrusion porosimetry (MIP) technique. This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Curing temperature strongly influences the mechanical and microstructural properties of CHF and Gelfill samples. (iv) The microstructure analysis revealed that the addition of sodium silicate can modify the pore size distribution and total porosity of Gelfill which can contribute to the better mechanical properties of Gelfill. (v) The MIP tests suggested the microstructure of specimens were changed by adding sodium silicate in a way that the Gelfill samples had a higher percentage of fine pores than CHF samples.

Aug 1, 2013

By B. R. MacKay

Introduction The Corbin coalfield is one of the smallest, and at the same time one of the principal, producing bituminous-coal areas in southeastern British Columbia, and is unique on account of the great original thickness of one of its coal seams and the remarkable concentration of coal in a small area that has occurred through intense folding and faulting of the measures. These are such that the deposit has been referred to at times as "the world's thickest coal seam" and as" a mountain of coal." The determination of the number, thickness, and character of the seams present, and the structure, extent, and geological relationship of the several deposits, are of vital interest both to the operating company in its endeavour to evolve the most efficient method of mining these exceptionally thick deposits and to the Government in estimating the coal resources of the different fields. With the object of ascertaining these data the writer was assigned in 1930 to geologically map and study the Corbin coal deposit. A topographic map covering Coal mountain and the immediate vicinity on a scale of 1 inch =800 feet, with a contour interval of 25 feet, made by the Topographic Division of the Geological Survey, served as the base for the geological mapping.

Jan 1, 1931

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007

By V. A. Ettel

Current practices in electrolytic winning and refining of copper , nickel and zinc are reviewed from the point of view of their respective energy requirements. The electrical energy requirements of these processes are broken down in to the individual components, which belong to two basic categories: (a) thermodynamic energy requirements (G of the desired reaction) : (b) energy losses (anode and cathode polarizations, ohmic drops in the electrolyte and in the cell hardware, energy losses due to unwanted side reactions and electrical shorts). The individual energy components are separately examined for each electrolytic process and the potential for energy saving in these processes is discussed. It is shown that many potential energy-saving measures are uneconomical at the present time, as they increase over-all operating costs. The discussion is focused on those approaches which hold most promise for the future.

Jan 1, 1977

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By Hans E. Madeisky, Bruce W. Downing

Abstract-The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: anorthosite-hosted magmatic sulfide nickel, dunite-hosted magmatic sulfide nickel, porphyry copper-gold, and volcanic-hosted high sulfidation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray fluorescence equipment, already used for grade control at many mine sites, could provide the wholerock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai.INTRODUCTIONComminution is a very energy intensive process. It consumes approximately 5% of the electricity produced worldwide and more than 50% of the total energy used in mineral processing plants (Pokrajcic, 2010). Among all the comminution stages, ball milling is one of the most energy intensive processes. In ball mills, rotational movement provides the rise of the load and the media that are projected and impact on the mill shell at lower angular displacement, resulting in particle breakage. Ball mills are able to reduce particle size over a relatively wide range of particle sizes. This explains their wide applicability in research laboratories and the mineral processing industry."

Jan 1, 2017

By J. E. Gillespie

Introduction Mineral wool may be defined as "rock, slag, or glass fibres made by a process of melting and blowing by steam or air, containing a minimum of oil and unfiberized material" (U.S. Bureau of Standards CS 117-44). The earliest production of the material was in Wales, about one hundred years ago. In the United States, the industry daces from 1870 when a plant, using slag as raw material, was established in Greenfield, New Jersey. It was not until 1897, however, that large-scale production was commenced on this continent at a plant in Alexandria, Indiana, which utilized rock from nearby deposits. Today, mineral wool is manufactured in many parts of the United States and Canada, the plants for the most part being in close proximity to deposits of suitable rock or to sources of slag. In the United States there are some seventy-five producers with a total annual capacity of nearly one million tons of wool. In Canada, in 1946, eleven manufacturers produced about fifty million square feet of batt-type mineral wool insulation material. Mineral wool is, perhaps, the most efficient of all heat-insulating materials and, moreover, it is fireproof, extremely durable, and insect- proof. Its high efficiency is due to the very low thermal conductivity of the fibres themselves and to the fact that the produce as marketed contains up to 90 per cent non-conducting air space. Depending on the degree of compression of the fibres in the manufactured product, the specific gravity ranges from 2 lb. to 10 lb. per cubic foot. Products Marketed Following are the principal forms in which mineral wool is marketed: Blanket. - Mineral wool with or without reinforcing on one or both sides, with various types of confining media, all suitably bound together.

Jan 1, 1948

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By S. Oppenheimer, P. Au, R. M. Kearsey, J. Tsang, E. McDevitt

A new superalloy, ATI 718Plus® Alloy (718Plus), has been developed to have a 55oC higher temperature capability over the traditionally used Alloy 718, while maintaining favourable processing characteristics and intrinsic raw material costs. The fatigue and dwell-fatigue behaviour of four microstructural variations of 718Plus are evaluated and compared to Waspaloy: 1) standard heat treated condition (HT1), 2) standard heat treated condition with thermal exposure at 732ºC (1350ºF) for 1000 hours (HT2), 3) fine grain condition with a modified d phase (HT3), and 4) fine grain overaged through modified heat treatment (HT4). The results show that the steady-state fatigue crack growth rates of each microstructural variation and both alloys are identical, with all of the 718Plus variations showing a clear advantage over Waspaloy in the fatigue crack threshold regime. Dwell-fatigue results show that Waspaloy has better resistance to crack propagation under dwell conditions; however, optimization of the precipitate phase shows vast improvement in the dwell-fatigue resistance of 718Plus.

Jan 1, 2010

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992