Search Documents

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By Karl J. C. Harries

"7.1. INTRODUCTIONThis chapter addresses the joint venture and examines a number of general concepts of the joint venture relationship. Chapter 8 looks at some specific concepts related to the provisions of a joint venture agreement, which are equally applicable to a shareholders’ agreement or other contractual relationship. The term “joint venture” is used because the author is a common law solicitor (a matter of convenience for which apologies are offered to civil law readers), but it should be noted that, in many aspects, the legal structure of an entity is irrelevant. It is the relationship of the parties, be they venturers or shareholders, that is important, and the areas of concern are surprisingly similar (except for terminology).The details of the joint venture relationship and agreement could fill several books. Accordingly, this chapter and the next focus on selected topics that appear to have caused problems or confusion or to be the basis for disputes. And remember that, although the following discussion is in the context of a joint venture, many of the comments apply, either directly or indirectly, to virtually any common undertaking and the agreement defining it.For interest’s sake, this chapter starts with a summary of some of the earlier types of agreements and arrangements that have evolved into the joint venture agreement of today in Canada, the philosophy of their format, and the reasons for their demise.7.2. EVOLUTION OF THE CANADIAN JOINT VENTUREThe Early DaysMuch of the opening up of Canada’s north is due to exploration for and development of mines. The early discoverers were relatively free to roam and explore at will and, if they were fortunate enough to find something, they dealt with the appropriate government to acquire exploitation rights. The early interests lay in gold or silver. Workings were small, usually worked by the owner alone or with only a couple of helpers to extract the native gold or silver. If the owner wanted to move on, he could sell his property outright and use his stake to look elsewhere.As logging and mining camps were opened, the development of better roads and railways made access easier. Entrepreneurs saw the opportunity to make money by assembling large parcels of land and working them as a single operation. In order to do this, some owners who were not ready to sell out had to be convinced to do so through more attractive offers"

Jan 1, 2003

By David R. Winfield

I would like to thank you for spending the time with me today to review the FLIR PathFindIR thermal imaging camera system: It is truly an innovative safety system that has the added benefit of offering increased efficiency Our company the Winsted Group, specializes in mobile video systems that are fully customizable to address standard and unique operational requirements in a variety of industries from heavy equipment cameras to police and military digital recording systems, high end video camera systems are a hallmark of Winsted?s product line. The use of thermal imaging camera systems to enhance mobile safety is a relatively new concept as it relates to their use in both transportation and heavy equipment operation. This technology, like so many before it, has been adopted for civilian use from its military roots. The identification of enemy combatants through their heat signature has given our troops a decisive edge in military operations in total darkness Likewise, the ability to discern people and objects that give off heat is a significant step forward in collision and accident avoidance. The PathFindIR camera system that I am demonstrating today is so advanced that it cannot be exported outside of continental North America without a US government approved export license I would like to commence my presentation with a short video clip that discusses the technology associated with the FLIR PathFindIR Thermal Imaging camera systems. The video demonstrates the operational effectiveness of thermal imaging camera systems installed on a vehicle operating on the roadway at night, of course there are definite parallels to use in a mining environment, primarily the fact that lighting is limited and the chance for vision limiting dust is ever present. We are, of course more concerned with personnel safety in our mines than encountering wildlife on the roadside. From the same perspective, the transport driver is just as concerned with encountering a stalled vehicle as our mine truck operators are with other mine traffic.

Feb 1, 2008

By M. Palfreyman

"Most of the minerals employed in Canadian refractory production are imported; in fact, most of the refractories consumed in Canada are imported. Whereas this situation is partly due to a definite shortage of suitable raw materials, e.g., fire clays, it is possible that the potential of certain mineral deposits which could be usefully exploited has not been recognized. There are exceptions, notably magnesite and dolomite, from which refractories are produced in Canada.In many cases, known mineral deposits are located either in inaccessible areas or in areas where transportation would be a major economic factor. This paper lists some minerals and their respective known deposits which could be employed in the production of refractories, irrespective of economics."

Jan 1, 1973

By B. Yu, S. Kelebek, C. Gibson, M. Aghamirian

There are a number of high grade niobium deposits worldwide which have been deemed untreatable by flotation due to the very fine grained nature of the in situ pyrochlore, the primary niobium bearing mineral. A known method of recovering extremely fine particles is through the use of chelating reagents such as hydroxamic acids which have a strong affinity for transition metals. However, one of the major issues in the flotation of niobium bearing minerals using hydroxamic acids is the corresponding recovery of other transition metal gangue minerals including magnetite, hematite, and pyrite. In order to better understand the differences in behavior of niobium and iron bearing minerals in flotation with benzohydroxamic acid (BHA) and sodium hexametaphosphate (SHMP) at a range of pulp temperatures, a Box-Behnken experimental design was employed. Regression models for the global recovery of iron indicated that iron mineral recovery was significantly influenced by both BHA and SHMP dosage. Upon examinination of flotation products by semi-quantitative XRD, it was observed that recovery of iron oxide and sulphide minerals (hematite, magnetite, goethite, and pyrite) was problematic at high benzohydroxamic acid dosage, while sodium hexametaphosphate was mainly helpful for carbonate mineral depression. Iron rich carbonates (likely an iron rich dolomite) largely reported to the tails with increased SHMP dosage.

Jan 1, 2015

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By Staff

This paper contains an outline of the history of the Sullivan mine, now owned and operated by the Consolidated Mining & Smelting Company of Canada, Ltd.; some account of the various methods by which the ore has been treated in efforts to solve the metallurgical problems which its complex character presents, and, finally, to give, as concisely as possible, an outline of the present mining and metallurgical practice along with a description of the mining and milling plant at Kimberley and the smelter and refineries at Trail, in British Columbia. EARLY HISTORY In May, 1892, Pat Sullivan, John Cleaver and Mike Holland left the Coeur d'Alene country, in the State of Idaho, to seek their fortunes in the Kootenay lake district in British Columbia. They were aided in their venture by James Cronin, afterwards locator and owner of the St. Eugene mine at Moyie. Two months later the party broke up, Sullivan and Cleaver crossing the mountains from Crawford bay on Kootenay lake to the head waters of the St. Mary's river, the course of which they followed down to Fort Steele. Here they found a good deal of excitement about the North Star mine, and, joined by "Ed." Smith, who was familiar with this part of the country, they determined to return and prospect in its vicinity.

Jan 1, 1924

By Graham Walker

A new Code of Practice for the brake performance of off -highway vehicles was established in Alberta in 1976. Vehicles loaded to gross vehicle weight must be capable of stopping with mechanical brakes five times in quick succession on a grade of 10 per cent from a speed of 28 miles per hour. Comparative trials of various brake systems have been carried out and some combinations capable of meeting the Code are identified. Some problem areas in truck braking are reviewed and potential developments indicated.

Jan 1, 1977

By E. Laatio, W. McKay

"History of Tara Mines Ltd.Tara Exploration and Development Company Ltd. was formed in Canada by Irishmen in 1953. The discovery of an orebody approximately six miles from the historically famous Hill of Tara in County Meath was a wild dream . Nevertheless this dream became a reality. Tara Mines Ltd. was formed, and the mine developed some 35 miles northwest of the City of Dublin in the Irish Republic.Tara's original drilling program indicated a zinc-lead orebody of approximately 60 million tonnes grading at 10.1% Zn and 2.6% Pb. The terms of the mining lease stipulated that the Irish government would acquire 25% equity interest in the operation. The mine was thus owned 75% by Tara Exploration and Development Company Ltd. of which the principal shareholders were Noranda and Northgate, together with 25% being held by the Irish government. The mine was purchased in March 1986 by Outokumpu Oy, a Finnish mining and metallurgical company, and together with the 25% government stake are the current owners. Outokumpu Analysis on Tara Mines Ltd.Upon ownership Outokumpu carried out a comprehensive analysis on the operation and came to the following conclusions :1. Tara had a good orebody;2. Tara had a skilled, capable, stable workforce;3. Tara's concentrator and processing equipment was adequate to meet requirements;4. Tara's mobile equipment fleet was too old and too numerousin numbers; and5. Tara had too many employees, both staff and hourly paid .With ore reserves of approximately 50 million tonnes and at a planned extraction rate of 2.6 million tonnes it meant that the mine had a lifespan of approximately 20 years. To be a viable operation into the future, the mine had to become more efficient. Operating costs and manpower levels had to be dramatically reduced."

Jan 1, 1989

By J M. Anderson

The cable belt conveyor installation at Craigmont Mines Limited, Merritt, B.C., has the greatest one-stage vertical fall of any conveyor installed overland in Canada. Since the late summer of 1961, this conveyor has carried more than 5,000,000 tons of copper ore from open pit to concentrator site. When the conveyor is loaded, the drive motor acts as an induction generator, delivering power to an external circuit. This paper covers the selection, the operation, the performance statistics, and the installation and operating costs of this conveyor system. Introduction T HE Craigmont mine is located in the south-western interior region of the Province of British Columbia, approximately 240 miles northeast of Vancouver. A moderate climate, good roads, service by the Canadian Pacific Railroad, power from the British Columbia Hydro Authority, gas from the nearby main line of the Inland Natural Gas Company and close proximity to the village of Merritt provide a favourable location for this mining operation. The ore occurrences at Craigmont have a vertical extent of 1,500 feet,

Jan 1, 1965

By Ernest A. Hodgson

A SERIOUS hazard which must be faced in some mines, though quite absent in others, is that of rockbursts. Bursts cannot be wholly avoided in such mines, but the hazard would largely disappear if they could be predicted. The problem of prediction resolves itself into that of measuring pressure in the mine and determining when that pressure nears a critical value. The geophysical approach to the problem lies in discovering some physical property of the rock, which varies with pressure, which can be measured for rock in place, and for which the indication of critical conditions is sufficiently definite and open scale. A physical property, suggested first in connection with earthquake pre-diction, is that of sub-audible snapping. It was argued that, as the pressure grows, the rock probably yields microscopically and that minute snapping occurs which is so faint as to be inaudible to the unaided ear. Experience has proved this to be the case. Following other earlier work begun early in 1939, experiments with this method were initiated at Lake Shore Mines in 1941, and equipment was slowly being developed in practice when, fortunately, it was found possible to by-pass this tedious development programme. Experiments with sub-audible snapping in mine rocks had been carried out by Dr. L. A. Obert of the U.S. Bureau of Mines and his associates over a period of about four years. An amplifier and a recorder were developed, each reasonably satisfactory in practice. Lake Shore Mines offers a tempting field for rockburst research. Dr. Obert was invited to test his equipment in this and other mines in Ontario and did so. As a result, he and the administrative personnel of the Bureau became interested in the Lake Shore experiments co the extent of most generously arranging for the manufacture of sets of their own designed equipment for use in this programme. The first three sets of recorders were ordered at once and were delivered in May, 1942. A second group of three sets, incorporating various improvements indicated by experience both in the United States and in Canada, reached Kirkland Lake in April, 1943. The pick-up devices, known as geophones, were made in the electronics laboratory at Lake Shore by Mr. Zack Gibbs, who has had charge of all the instrument development in this re-search.

Jan 1, 1943

"The success or failure of coal mining operations in Western Canada may hinge on the ability to extract thick coal under a variety of geological and mining circumstances and conditions. The paper presents, in who-where, what- how pattern, the current status of undergrounud mining of thick coal seams based on a review of foreign technical literature. The underground production of coal from what are considered to be thick seams is over 300 million tons per year. Methods of mining have evolved, through years of trials and tribulations, capable of meeting the requirements of a modern mine: high bulk outputs from a limited number of mining faces by concentrating in the horizontal (mechanization) and in the vertical (increased working lift)."

Jan 1, 1972

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

By L H. Warren

The types of equipment available for generating a plasma have been reviewed. The efficiency and potential of the plasma generating equipment used in performing extractive metallurgical reactions have been determined. A general classification of the reactions that might be per-formed in a plasma has been proposed. Experimental work done on extractive metallurgical plasma reactions, heat transfer between the plasma and solids, and the quench of the products of plasma reaction has been summarized. From the preliminary results it appears that the high-intensity are or the transpiration-cooled anode plasma torch offer the most promising areas for further research. C ONSIDERABLE world-wide research effort is currently being devoted to the development of processing technologies which employ the new high-temperature generating devices that have appeared over the past few years. The plasma flames produced by these devices offer the potential for subjecting materials to any single gas or mixture of gases at temperatures up to 20,000°K. With these conditions available, many reactions in extractive metallurgy,

Jan 1, 1965

Of the twelve known ore zones on the Sunro property, acquired by Cowichan Copper Co., only the "B" and "C" orebodies of the "River Zone" had been explored sufficiently to indicate the grade and tonnage. The "B" zone was selected for initial production. The portion of this orebody above the main adit level was developed for horizontal-ring, longhole mining. Ore from the stope would be scraped directly to the coarse ore bin. The lack of a suitable mill site on surface, as well as the 8,000-ft. tramming distance, led naturally to the installation ground. I N November, 1960, a lease was obtained by Co-wichan Copper Co. Ltd. (N.P.L.) from Sunro Mines Ltd., covering the main ore (River) zone of the Sunro property. A total of twelve zones had been located on the property. Nine of these lay within the leased area. With the exception of the "B" and "C" orebodies of the River Zone, there had been insufficient exploration for tonnage and grade calculations. Exploration by previous companies had

Jan 1, 1965

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

By M. L. McAllister, M. Veiga

The mineral industry has seen many significant changes in the past decade. Increasingly, it has responded to unanticipated pressures and demands with a variety of voluntary initiatives. Yet there is still much to do. Mining now takes place in a different context than was the case in the past. Socio-economic, political and environmental considerations must now be integrated into traditional mining systems. This process of integration needs to involve industry, governments, academics, communities and other stakeholders to design a new approach to mining, one that can be fostered through interdisciplinary links and holistic strategies. This paper considers the meaning of sustainability in the context of the Canadian mining industry and explores the need for a broader vision for the mining industry. The role of technology is then analyzed and related to an initiative recently taken by Canadian universities to develop a national network for interdisciplinary research into sustainable mining, CaSM.

Jan 1, 1999

By F. Chiesa

Forty aluminium A356 castings were poured on a Low Pressure Permanent Mould industrial machine, 500x700mm in platen size. The 152mm wide casting comprised three steps, 25mm, 13mm, 6mm in thickness and a 2.5mm overflow which allowed to assess the thin wall capability of the process. The casting campaign, which produced 40 parts, allowed to test the influence of various production parameters including the time of application of the pressure in the crucible, artificial cooling of the mould and casting rate. The thermal history in the mould was recorded over the 40 cycles, which allowed to construct a reliable thermal model of the mould/casting assembly. The metallurgical quality of castings representative of the various conditions was assessed in the 25mm, 13mm and 6mm plates. This included measuring the level of microporosity, the dendrite fineness (DAS), along with the tensile properties in the T6 condition. The radiographic quality per ASTM E155 was also determined. Modelling filling and solidification allowed to verify the validity of the predictions based on available relationships relating microporosity, secondary dendrite arm spacing (DAS) and local tensile properties (Quality Index, Q) to the local thermal solidification parameters.

Jan 1, 2007

By Eduardo A. Pérez, Alejandro R. Alonso, Rosa María Luna-Sánchez, Gretchen T. Lapidus

Rare earth elements have been widely used in various sectors, from the aerospace and steel industries, to electronic applications, particularly in displays and batteries for portable devices. The high demand for newer and better equipment, such as cell phones, tablets and lap tops, has increased the consumption of the rare earth elements and at the same time the need for its recovery from electronic wastes. For that reason, the recycling of batteries is important, principally the Ni-HM batteries, due to their elevated content of rare earths elements, in addition to the high concentrations of cobalt and nickel. The current processes are based on dissolution in strong acid solutions (sulfuric acid concentrations from 2 to 4 mol/L), and temperatures from 30 to 90°C. In the present work, electrodes from spent Ni-HM batteries were leached using 1 mol/L H2SO4, in the presence of ozone as the oxidant, where recoveries of 96% for La, Ce and Nd were obtained at room temperature. The separation of Ni and Co from the leach solutions was performed using an electrochemical reactor, after which rare earth elements were precipitated, obtaining a mixture of its hydroxides with impurities below 1%, according to EDS analysis.

Jan 1, 2014

By Nicola Robjohns, Kenneth A. Grace, Jane Spooner

"The important volume end use sectors for the rare earth elements and yttrium continue to be in steelmaking, petroleum cracking catalysts and glass polishing. The market sectors which may provide future high volume demand, to replace the older sectors where demand has declined over the past decade, include magnets, automobile catalysts, ceramics and superconductors. Increases in production capacity in all major rare earth producing countries are expected to restrain large price increases for high purity rare earth oxides over the short term. A sharp increase in demand for yttrium in advanced ceramics and superconductors would lead to a shortage in separation capacity, however, and to a corresponding rise in prices for separated rare earths.IntroductionWhile visiting the Geology Department of the University of Toronto in 1981, Professor Lu from the Institute of Geochemistry of Academia Sinica at Gweiyang in China introduced one of his seminars with the observation that in China, rare earths are not rare at all.Indeed, while being rare in terms of abundance as measured by, say, the Clarke scale, the rare earth elements, like many other low abundance elements, are subject to geological, geochemical and mineralogical concentration.The rare earth elements comprise the fifteen inner transition elements of Group IIIB, Period 6, of the periodic table, from lanthanum to lutetium (the lanthanides), as set out in Table 1. The rare earths constitute a distinct group as they have extremely similar chemical characteristics due to the uniformity of their outer electron shells. The element yttrium is usually, by convention, included in the rare earth group as it occurs with the rare earths in nature and has properties very similar to them.The rare earths are divided into two subgroups, the ""light"" rare earths, made up of the first seven elements of the series, lanthanum to europium, and the ""heavy"" rare earths, comprising the remaining eight elements, gadolinium to lutetium, plus yttrium. These two subgroups are also referred to as the cerium subgroup and the yttrium subgroup, respectively. The subdivision is based on differences in the atomic radii resulting in somewhat different properties for the two subgroups."

Jan 1, 1991