Search Documents

By M Spiteri, S Woth, J Caratti, K Henley

Blasting is an essentially violent process aimed to disrupt and loosen rock for productive excavation and downstream processing. Dilution of the orebody to some extent is the inevitable result, particularly in narrow vein gold mines. A small change in gold recovery is usually a strong lever on revenue generation. As a result blast designs are carefully engineered to both minimise and control the direction of rock movement. Traditionally blast designs in gold mines have used the minimum powder factor that will still permit rock excavation. This now conflicts with the recent industry trend to optimise the total process flowsheet from the mine to the mill. Numerous mines have achieved success in reducing total mining cost by increasing powder factors. Not only is explosive energy cheaper than mechanical comminution energy requirements, the increased blasting effect may deliver benefits across all downstream processes of digging, hauling, crushing and milling. Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operation is the largest gold mine in Australia, located in the heart of the Kalgoorlie Goldfields. Blast dilution has been reduced at KCGM by managing location of blast boundaries and by firing along strike to choked faces. Significant economies of scale have resulted from application of a bulk mining methods. The bench height of 10 m is the largest in the Western Australian Goldfields, and is typically mined in a single pass with large face shovels. Recent increases in production rates in both the mine and mill has been partly attributed to a 30 per cent increase in powder factor. KCGM then examined the benefit of a further 18 per cent increase in powder factor to 1.0 kg/BCM. A concern though was the impact of very high powder factors resulting in excessive blast movement and subsequently ore dilution. This was the subject of a project conducted with Orica Explosives. OricaÆsDMC(Distinct Motion Code) blast model was applied to understand the effect of not just further increases in powder factor but also blast geometry and explosive type. The modeling work demonstrated that high powder factors may be applied with minimal increase in ore dilution provided the combination of blast geometry and explosive type is optimised. These results are currently being implemented to achieve further reductions in total mining costs without a significant impact on recovery.

Jan 1, 2001

Investigations of the Mineragraphic Section; Commonwealth Scientific and Industrial Research Organisation, have included most of the known stannite-bearing ores in Australia, and have revealed several new occurrences of this relatively uncommon mineral. They provide information about its paragenesis, and its possible effect on tin recovery, that may be of general interest.Several of the investigations used in the preparation of this paper, were made in the first instance by pr. F. L. Stillwell or in collaboration with him.CASSITERITE-SULPHIDE ORES IN NORTH-WEST- TASMANIA Stannite is a minor component of most of the cassiterite sulphide ores of north-western Tasmania. These include the orebodies of Mount Bischoff, the Cleveland mine, Moina, the Stanley River district, Renison Bell, and the Heemskirk-Zeehan district, and form a well defined metallogenetic provence which is related to the Devonian granites of this part of Tasmania.In these ores mineralisation began. with deposition of cassiterite, a little wolfram, and quartz, topaz and tourmaline. With falling temperature, deposition of cassiterite ceased and arsenopy-rite, pyrite, and especially pyrrhotite, formed in abundance, tending to give massive sulphide ore. A little chalcopyrite; stannite, sphalerite and native bismuth accompanied the pyrrhotite. Deposition of quartz ceased after the pyrrhotite, was formed, and the later-formed nonsulphide gangue consists chiefly of carbonates and fluorite. With, the advent of the carbonates the pyrrhotite was altered to fine-gained intergrowths of marcasite and pyrite. Excess iron from the pyrrhotite entered the intergrown carbonate, or was precipitated as magnetite. Some solution of the cassiterite occurred at this stage, the tin being redeposited chiefly as stimnite replacement rims around the residual cassitellrite grains. Varying, but small, amounts of sphalerite, galena, tetrahedrite and silver minerals were depoSited at this stage, bringing the mineralisation to a...

Jan 1, 1951

The stratigraphic sequence west of Mount Isa contains the Judenan Beds, Eastern Creek Volcanics, and May Downs gneiss. It is an incomplete sequence as major north-south faults divide the area into four separatezones containing portions of these different units. The first three zones, which occur directly to the west of the Mount Isa Fault, consist of quartzites and quartz-mica schists which are uncorrelatable between zones but have been grouped together as the Judenan Beds. The most western zone contains an incomplete section of Eastern Creek Volcanics which rests conformably on a unit believed to be equivalent to the Mount Guide Quartzite; this is again underlain by the May Downs gneiss. A detailed description of the rock types is presented, but only a broad stratigraphic correlation is possible with the very much thicker sequence to the east of Mount Isa.The age of sedimentation is believed to be Lower Proterozoic and it may not occur in the type of geosynclinal basin envisaged by previous authors.This sequence is intruded by many small basic intrusions and also the Sybella Granite with its associated microgranite and pegmatites. The Sybella Granite consists of both a massive and a foliated phase; the latteris generally restricted to the margin of the main granite mass.Four regional metamorphic zones have been identified on the basis of their pelitic mineral assemblages; these are a chlorite, biotite, biotite-cordierite, and a sillimanite zone; separating each are prominent north-south faults.This metamorphism is a regional metamorphism which accompanies the first generation folding of the area and is not associated with the emplacement of the Sybella Granite. A very localized retrogressive metamorphism is also found in some areas of second generation folding.

Jan 1, 1972

By J Välivaara

The mining industry will face numerous challenges over the next 10–15 years as new deposits are likely to be more remote and lower grade and existing deposits will be mined deeper. As a result, mines and mining contractors operating in deep-mine conditions will need to focus on the quality of drilling and blasting to minimise unnecessary waste rock excavation to keep costs at an acceptable level. In addition, increased demand for improved safety and operator ergonomics will set greater demands on original equipment manufacturers of mining equipment. Finally, difficulties finding a skilled and experienced workforce, particularly in remote mine locations, have already negatively impacted mines’ ability to achieve high productivity and low operating costs.This paper introduces techniques and shares practical experiences in increasing productivity and reducing the costs of excavation in underground face drilling. The paper uses Sandvik’s new DD422i automated mining jumbo as an example of the type of equipment needed to deliver the features and corresponding benefits for future mine development. Case studies using this equipment are presented to illustrate the points made in this paper.CITATION:Välivaara, J, 2016. Automated drilling features for improving productivity and reducing costs in underground development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 723–730 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S Joyce, Z Agioutantis, D van Zyl, D Shields

Over the past 15 years, the mining industry has begun to incorporate the concepts of sustainable development and sustainable mining practice across the life cycle of mineral operations. This requires addressing economic issues, community impacts and concerns and environmental protection, and is captured in part by the phrase ‘design for sustainability’ (McClellan et al, 2009). Over the same period, the industry has seen a gradual decline in ore grades for many mineral commodities. As a result, large volumes of tailings and mine waste rock are being produced around the world, and it is expected that the annual production volumes of these materials will increase, even if there is not a significant change in the demand for materials.Another related thread of change has been the realisation that societies need to move away from linear economies (raw materials, production, consumption, disposal) towards more circular ones. This will help societies become more resource efficient, which is defined by the United Nations Environment Programme as reducing the total environmental impact of the production and consumption of goods and services, from raw material extraction to final use and disposal. The goal is to create more with less and deliver greater value with less input. Circular economies require thinking in terms of the waste hierarchy (reduce, reuse, repurpose, recycle, recover, landfill).The challenge is that the waste hierarchy was originally designed to address embodied mineral content in products rather than mine waste and tailings generation. It will need to be reconsidered in a mine life cycle context, focusing on a value-based conception of waste (Van Ewijk and Stegemann, in press).In parallel to these changes, it has remained an imperative in the mining industry to dispose of these waste materials as economically as possible while protecting the environment. Single handling of these materials has been the main target, which reduces the life cycle costs of their management but may make reuse of waste and tailings technically more difficult or economically infeasible.This presentation explores a rethinking of the large volume earthen material waste issue at mines. The underlying theme is that some or all of these materials can be valuable resources for the future that can positively contribute to sustainable development. These resources can offer economic gains to firms, communities and societies; contribute to environmental well-being; enhance social interactions with the previously mined landscape if handled properly; and, with proper policies in place, reduce governance commitments. Each of these topics will be briefly explored. This will be followed by a discussion of approaches to manage design and operations to allow future resource recovery.CITATION:Van Zyl, D, Shields, D, Agioutantis, Z and Joyce, S, 2015. Waste not, want not – rethinking the tailings and mine waste issue, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

The original and most basic relationship between mining company and explosive supplier was a simple one of consumer and product supplier. The divide between the two was quite clear-cut with neither taking much interest in the activities of the other. The explosive supplier had little understanding or share in the outcome, efficient rock breakage and therefore impact on mining and milling. Likewise, the mining company did not encourage the improvement or development of products. The transactions were limited to product and funds. This environment does not encourage any form of knowledge sharing, trust or optimisation of the mining process.Conversely, there are now a variety of relationships to the point that the mining company may simply be an asset manager whereby all æoperationalÆ aspects are contracted out. For the drill and blast aspect this takes the form of a æRock-On-GroundÆ contract whereby the explosives company takes on design, drill, load and fire responsibilities and is paid a rate per volume of broken rock. This removes the majority of risk to the mining company derived from having to produce broken rock and guarantees the cost of a portion of the overall unit cost of mining. The onus is now on the explosives supplier to break rock to a specification as efficiently as possible.There exist a number of variations between the æbasic supplyÆ and æRock-On-GroundÆ. These contracts may also include value sharing to encourage the explosive supplier to optimise the mining operation to maximise profit.This paper looks at some of the drivers for the change in explosive supplierûconsumer relationships and examines the æprosÆ and æconsÆ of a few of the options.

Jan 1, 2004

By G Turner-Saad

An improvement to cut-off grade optimisation theory based on geometallurgy has been completed. The improvement fundamentally consisted of taking into account mineralogical and textural characteristics instead of grades. These characteristics are related to the spatial variability of mineral abundance, association, particle size and liberation properties. Additionally, the improve- ment considered the spatial variability of mineral processing liberation and selectivity properties associated with mineralogy and texture. The enhanced optimisation enables estimation of the economic value of mining operations based on an optimum cut-off policy attributed to liberated and selected ore minerals.The enhanced optimisation was developed as an essential component of a joint cut-and-fill mining and mineral processing methodology based on mixed integer mathematical programming. The formulation considers static and dynamic modifying factors that vary over the projected life of mining. The objective function of the mathematical formulation consists of maximising the realistic expected economic value of concentrates or products of liberated and selected ore minerals, whilst minimises liberated and selected gangue minerals. The optimal solution is obtained when the objective function is subject to geological, mining, processing, marketing, smelting, refining, environmental and financial constraints. The methodology accesses geometallurgical multivariate resource models, which integrate the spatial variability of mineralogical and textural characteristics and mineral processing liberation and selectivity properties.The geometallurgical process concurrently optimises stope geometries, ore reserves, mining sequences, and mining and mineral processing production based on the enhanced cut-off of liberated and selected ore minerals. In addition, the process considers additive and non-additive transfer functions associated to mutually exclusive geometallurgical spatial domains. The transfer functions also take into consideration the blending of mineralogical and textural characteristics with mineral processing liberation and selectivity properties.This contribution presents an example of cut-off grade optimisation via mineralogical and textural characteristic, and liberation and selectivity processing parameter optimisation for a spatially variable orebody.

Sep 5, 2011

Underlain by and intruded into the sedimentary rocks of the Transvaal Supergroup the Bushveld Complex is the largest known layered intrusion in the world and contains one of the richest ore deposits on earth. It has been the world's major source of Platinum Group Metals (PGM) since the mid-1900s with Chromite and PGMs the two most economically important components of the Bushveld Complex. The lower group (LG), within the critical zone, consists of seven chromitite layers and it is within this sequence of chromitite layers, the most important target of the lower chromitite group is found, ie the LG6 chromitite unit. The LG6 chromitite unit consists of a chromitite duplex composed of the lower LG6 chromitite layer (Steelport seam), averaging 1 m thick, overlain by a 0.66 m waste parting and a thin 0.34 m thick LG6a chromitite layer (leader layer).Two mining methods are commonly applied in the Bushveld Complex to extract the LG6 chromitite layer package. One method consists of footwall development utilising rail bound equipment to gain access to the orebody and then extracts only the LG6 chromitite layer by means of hand held rock drills and scraper winches. The second method is the use of mechanised equipment to access the orebody on the plane of the ore utilising bord and pillar mining method, which extracts the full mineral resource, ie the LG6 and LG6a layers. Conventional narrow vein stoping is often selected due to the large conventional mining skills base found in South Africa, the perceived cost and dilution implications of utilising mechanised equipment, and the difficulties of using mechanised equipment at dips above 12¦. The driving factor for mechanised mining is the perceived ability to access the orebody quickly and inexpensively, and extract the entire mineral resource package (LG6 and LG6a) while limiting capital expenditure and improving safety.This paper investigates these two commonly applied approaches, highlighting the benefits and problems associated with the two approaches. Comparisons will be made of the two mining methods and recommendations given for the mining engineer to consider before selecting the appropriate mine design.

Dec 6, 2010

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004

A new least-squares method for inversion of d.c. resistivity soundings from horizontally layered earth is proposed. Powers are used as measured data. Apparent resistivity is generalized and apparent parameters curves are defined. Estimates for parameter errors are often possible even when data errors are unknown or large. Acceptance or rejection of a model is made an easier decision. Total computational effort is often reduced when compared to global least-squares methods, because although several optimizations are needed, few data points are involved in each, and initial guesses are requested only once and not all at the same time. Correlations between parameters may be used to improve solutions. Precise indications for extra needed data points can be conveyed. A test example is worked out and a field sounding, taken by Rijo (1973, personal communication) in an alluvium-filled river valley in north-eastern Brazil, is studied.

Jan 1, 1987

By Y Wang

Inadequate goaf gas control may lead to gas exceedances in the ventilation return air, which will trip power in longwalls and cause production stoppage. To effectively control gas emissions, Australian mines heavily rely on drilling vertical goaf holes to capture coalmine methane before it migrates to mine openings. The wide application of goaf gas drainage may change the goaf pressure distribution, lead to more ventilation air leakage, and consequently increase gas explosion and spontaneous combustion risks. This paper focuses on analysing goaf gas drainage production data from a case study longwall mine in Australia. The correlation between suction pressure, total flow rate, gas flow rate and air leakage rate were analysed in detail as the face-to-hole distance changes. Suction pressure is found to be positively correlated with total flow rate, and their correlation also varies at different goaf locations due to various goaf compaction and flow resistance. This paper also proposed a theoretical method to calculate the goaf resistance of ventilation air leakage pathways. Based on several basic assumptions and different goaf drainage scenarios, the leakage airflow pathway resistance in the goaf at different face-to-hole distances can be calculated. The model results suggested that the resistance of air leakage pathways from the working face to individual goaf holes increased with the face-to-hole distance. The resistance results can also be used to calculate the corresponding permeability at the same position, which can be used as input data for CFD or Ventsim models.

Oct 12, 2022

The different electrowinning cells presently developed for recovery of gold from CIP eluates are compared and contrasted. The efficiency of operation for each cell is,discussed in terms of the electrochemistry of (a) gold deposition, and (b) packed bed electrodes. The advantages and problems associated with each cell design are presented and recommendations are made as to the best method of gold recovery.

Jan 1, 1982

By Williams J. D

Magnetite has been used in coal processing for many years and it is likely that its use will continue well into the twenty first Century. While magnetite is only a minor cost component in coal processing, the use of processed magnetite in dense medium separation is essential to provide the split of quality coal products which the markets of today demand. The occurrence of magnetite in Australia is relatively abundant, but a combination of its iron content, magnetic properties, quality and proximity to the coal processing plants is essential to provide a low cost product for use in the Coal Industry. The demand for more splitting of coal in coal processing may require more grades of magnetite, particularly as a finer grade lower specific gravity medium to separate the finer quality low ash coals.

Jan 1, 1991

The emerging coal seam gas (CSG) industry has the potential to provide a large-scale energy province for Queensland. Aquifer impacts and management of associated by-product water, both in terms of quantity and quality, are pivotal considerations for the development of a sustainable CSG industry.Legislative changes have been introduced to ensure that the CSG industry manages potential groundwater impacts and beneficial reuse of the by-product water to a level acceptable to both government and the community.The relevant new pieces of legislation covering petroleum and coal seam gas activities include the Petroleum and Gas (Production and Safety) Act 2004 (P&G Act), Petroleum and Other Legislation Amendment Act 2004 (POLA Act), the Petroleum and Gas (Production and Safety) Regulation 2004 and the Petroleum Regulation 2004. Other relevant legislation includes the Petroleum Act 1923 (Petroleum Act) and Part 7AA of the Mineral Resources Act 1989 (Coal Seam Gas Regime). The P&G Act introduces a full regime for managing water rights. This includes provisions for monitoring and reporting on the effects that the taking of underground water under petroleum tenure has on other bores in the area. The P&G Act also imposes a æmake good obligationÆ on petroleum tenure holders, which requires the restoration of bores affected by the taking of water or the payment of compensation. These provisions represent a significant departure from the Petroleum Act, which says very little about water rights and does not specify restrictions on the taking of water under petroleum tenure. This paper attempts to outline the requirements and obligations of the P&G Act for the CSG industry in terms of underground water rights, development impact assessments, aquifer trigger thresholds, monitoring and reporting requirements, as well as the make good obligations.

Jan 1, 2006

By J Heyes, T Cooper, M Stimpfl, R Staines, J P. Pearce

Acid and Metalliferous Drainage (AMD) is one of the key risks facing the mining industry worldwide. If not properly managed and/or not identified in a timely manner, AMD has the potential to decrease environmental values for generations to come. Ore extraction generates vast volumes of mineral waste (waste rock and tailings) which are stored in perpetuity at the mine site. Some of these materials are not inert and when in contact with air and water can react, generating poor quality water and compromising operational and closure environmental objectives. Understanding the geochemical behaviour of waste rock and tailings is therefore key to identifying risks and opportunities which support effective mineral waste management strategies across the mining value chain and progress toward an environmentally sustainable future that minimises closure liabilities. To ensure AMD risk is recognised and managed uniformly across its portfolio, BHP developed a Global AMD Management Standard for implementation across all operations, including closed sites. The AMD Management Standard provides a management framework to support the consistent, simple and sustainable global management of AMD risks. This ensures mines are planned and operated to be environmentally smart and modern, geochemical risk management is not an afterthought but a key driver, and environmental sustainability is actively pursued to reduce closure liabilities. The AMD Management Framework, on which the Standard is based, was adapted from industry leading practice guidance, ensuring it applies to multiple regions. The framework also comprises sequential requirements throughout the mining life-cycle. It is an iterative framework with an adaptive management approach that is designed to incorporate new data, information and management opportunities into AMD risk assessments and mine plan revisions.

Jul 1, 2021

By D H. Laubscher

The in situ rock mass rating system û IRMR - leading to the mining rock mass rating system - MRMR - for jointed rock masses has been used (and abused) in mining operations around the world for the past 27 years. Despite the recent development of elaborate design procedures and computer-aided design packages, MRMR remains one of the most versatile and practical mine design systems available. It is important to realise that the rock mass classification system should not be replaced but rather complemented by more sophisticated and detailed design procedures. The classification system is not only the æcrudeÆ method used for initial assessment (as described in some geotechnical literature) but also in many respects a very effective and practical engineering tool. MRMR could, and should be used during the entire stage of mine life as an integral part of the design process. The objectives of this paper are to illustrate using practical case histories from the past decade, some of the pitfalls of the MRMR classification system, to clarify certain misconceptions in its application and update its mining application.

Jan 1, 2000

By T Stambolie

Mine planning processes are continuously evolving, increasing in complexity, and are required to be developed in shorter timeframes, often missing important steps in the process. Underground coal mines are also moving into more challenging environments, with the more favourable resources having been exhausted. In addition to traditional mine planning processes there is an increasing level of complexities associated with parallel systems including the preparation of Joint Ore Reserves Committee (JORC) compliant estimates (JORC, 2012 and Guidelines Review Committee, 2014) or seeking critical regulatory development consent to undertake mining. There is a clear link between geotechnical considerations and success of mining operations, and therefore it is essential that such considerations are elevated in both status and priority. It is obvious that geotechnical considerations are paramount in any mine, however it is imperative to accept that such considerations, and the collection of information relating to such, are undertaken from the onset of any mining project. CITATION:Stambolie, T, 2018. Elevating geotechnical considerations in the Australian underground coal industry and mine planning process, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 383–391 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By E Nettleton, A Melkumyan

A probabilistic system for autonomous tracking of excavated ore in mining would be highly valuable. Currently, mine sites can have a vast array of sensors; examples include excavator load cells, bucket volume estimators and haul truck strut pressures which can be used to gather information about the excavated ore at different locations. These sensors can be utilised efficiently to increase the accuracy of mine estimates by introducing a real-time ore tracking system. This requires the introduction of a probabilistic ore tracking framework to consistently fuse information from any sensor input. Current modelling practices are manually intensive, deterministic (no recognition of the quality of data) and generally not a complete end-to-end system. This paper will provide a novel method for tracking extensive ore properties (mass, volume) and intensive ore properties such as chemical composition (eg Fe per cent, SiO2 per cent, Al2O3 per cent). This method is proved to ensure that correct correlations between states are conserved as material is transferred, combined and/or separated at different locations with any configuration of sensor inputs. This ensures that consistency of estimates is maintained and other benefits such as real-time probabilistic reconciliation can be implemented. A method for combining material of different mass and chemical compositions is also developed to enable accurate and efficient operation of the system. Representative experiments on a small-scale and a larger field trial which mimic the mining processes of excavation, haul and unload to ROM Stockpile will be used to verify the approach.

Sep 26, 2011

The geology of an area in north-western New South Wales, bounded by the South Australian and Queensland borders, latitude 32° S. and longitude 14° E. is discussed.The area involved includes sixteen 1:250,000 standard military sheets and covers approximately 96,000 sq. miles.The geology of the Willyama Complex is not dealt with but a small area of metasediments previously included in this unit is separated and a possible correlation with Precambrian to the east is suggested. Torrowangee Group sediments are described and the problem of nomenclature using a glacial implication is raised.Nine areas of proven Lower Palaeozoic sediments are considered and their relationship to the boundaries of the Bancannia Trough outlined. It is possible that some exposures not yet substantiated by fossil evidence may prove to be Lower Palaeozoic rather than Precambrian in age.The sediments of the Lachlan Geosyncline in the area of the Cobar massif are described and new concepts on the age and distribution of some of the established stratigraphic units are introduced. The absence of rocks of Middle Silurian age probably indicates the time of a major orogeny in this area.Lithology, thickness, and distribution of the Upper Devonian sediments is considered and some of the more recently found fish plate localities are listed.Mesozoic sediments occur in isolated areas of Lower Jurassic age and in the Great Australian (Artesian) Basin. A four-fold subdivision of sediments of the basin has been possible in some areas but lack of sub-surface information at present, precludes the possibility of correlation with the type sections in Queensland.Units in the Cainozoic are subdivided and a five fold subdivision of the Quaternary, at present being used throughout western New South Wales, is described.

Jan 1, 1969

By C Philander

The West Coast of South Africa is well known for its placer gem quality diamond deposits and also associated with these hosts of Cenozoic unconsolidated marine and aeolian sand and gravel are significant concentrations of heavy minerals. Exploration for economic concentrations of zircon, ilmenite and rutile along the coast started in the mid-1980s. This resulted in the discovery of an inferred 1.6 billion tonne resource with a grade of ten per cent total heavy minerals (THM), which developed into the Namakwa Sands Mine, a world-class producer of heavy minerals. Several other resources, including satellite deposits proximal and distal to the mine area, extensive diamond mine dumps and present day beach placers, demonstrate the vast heavy mineral potential along the West Coast. The favourable gangue to economic mineral ratio, a higher zircon content compared to other similar deposits, relatively lower U+TH content of zircon, low slimes content and effectively pristine low chromium-manganese ilmenite of these deposits, render them attractive exploration targets. Negative factors that will affect conventional mineral beneficiation and liberation include secondary mineral coatings and the regional coastal development of several layers of superimposed duricrust. The economically attractive heavy mineral assemblage along the West Coast is the result of erosion of the proximal, gneissic Namaqualand Metamorphic Province and mature Table Mountain Group sandstone, concentration by marine and aeolian processes and preservation under arid climatological conditions over a period of more than 100 Ma.

Jan 1, 2008