Search Documents

Comparison of the Zadra, Anglo-American and organic solvent procedures for desorption of gold from activated carbon loaded in carbon-in-pulp gold circuits indicates that the Anglo American and the organic solvent procedures are considerably more effective than the commonly used Zadra procedure. Organic solvent elution procedures, particularly those using acetonitrile and acetone, can provide effective gold elution and very high concentrations of gold in eluate solutions. The operational simplicity and effectiveness of the Anglo American procedure would appear to make it the most satisfactory procedure available at the present time but this may change as the solvent elution procedures become better developed. INTRODUCTION The carbon-in-pulp technique has been introduced into the gold processing industry to by-pass the often lengthy CCD and filtration steps required in the conventional Merrill Crowe cyanidation procedure for gold recovery. Adsorption of gold on to carbon is also a valuable technique for recovering trace amounts of gold from low level waste streams from conventional processing procedures.

Jan 1, 1982

Routine, in-pit geological mapping of highwall at Central Queensland Coal Associates (C.O.C.A.) deep strip mines has proved too slow for the increasingly greater highwall lengths which require mapping. This realiz- ation has encouraged the search for faster mapping methods and after trial of ground photographic methods has resulted in the adoption of interpretive mapping off stereo cover, oblique -- aerial photography. This entails using a Cessna 182 light aircraft flying at its slowest speed, the aerial meth- od finally employed consisting of two Vinten, air reconnaissance cameras mounted in parallel and simultaneously taking both colour and black and white photographs of the mine high- wall. The respective 1:500 scale enlargements produced from the 70mm format films combine to present the sharpest resolution attainable under the field conditions pertaining and such information on weathered material as only colour photography can fully render. Total costs for the aerial photography method are estimated to be about the same as those for conventional in-pit mapping. Whilst total costs are comparable, geo- logist's time for mapping a 10 km. length is reduced to less than half that for in-pit mapping (for Stage 1, fully accurate mapping) and accuracy and detail are greatly improved. A permanent, accurate record of overburden

Jan 1, 1981

By J Demchak, L M. McDonald

The duration of acid mine drainage flowing out of underground mines is important in the design of watershed restoration and abandoned mine land reclamation projects. People conducting land reclamation projects usually employ remediation strategies once (reshaping land, revegetating soils, and installing water treatment) with the hope that these methods will adequately improve water quality for a long time, with little planning for future changes. An understanding of changing acid water conditions from underground mines over time will help in designing efficient and cost-effective treatment methods. Past studies have reported that acid water flows from underground mines for hundreds of years with little change, while others state that poor drainage quality may last only 20 to 40 years. Several factors are important in making a prediction of drainage quality over time, such as inundation or flooding history, coal seam characteristics (primarily sulfur content), residence time of water in the mine, time since mine closure, mining method and amount of coal remaining, collapse of roof and other disturbances within the mine, and subsequent nearby surface mining. More than 150 above-drainage (those not flooded after abandonment) underground mine discharges were located and sampled during 1968 in northern West Virginia, and we revisited 44 of those sites in 2000 and measured water flow, pH, acidity, alkalinity, Fe, Al, and sulfate. All 44 discharges were from mines in the Pittsburgh and Upper Freeport coal seams, and both seams have been extensively mined in this area during the past 70 years. We sampled during the same months (June to October) as were sampled in 1968, and we found no significant difference in flows between 1968 and 2000. Therefore, we felt that the water quality data could be compared and that the data represented real changes in pollutant concentrations. There were significant water quality differences between year and coal seam, but no differences between disturbed and undisturbed mines. Average acidity declined 79 per cent between 1968 and 2000 in Pittsburgh mines (from 3342 to 702 mg/L), and 56 per cent in Upper Freeport mines (from 1189 to 519 mg/L). Iron decreased an average of about 80 per cent across all sites (from an average of 345 to 69 mg/L), while sulfate decreased between 50 to 75 per cent. Pittsburgh seam discharge water was much worse in 1968 than Upper Freeport seam water. Twenty of our 44 sites had water quality information during 1980, which served as a midpoint to assess the slope of the decline in acidity and metal concentrations. Almost all parameters showed an exponential rate of decline in acidity, iron, and sulfate.

Jan 1, 2003

By N DavT

Pyritic tailings from the Quirke mine waste management area in Elliot Lake, Ontario were subjected to long-term column leaching experiments in two PVC columns measuring 122 cm in height and 15.2 cm in diameter. At the end of the leaching experiments, the columns were taken apart and sampled at 5 cm intervals for quantitative mineralogical and geochemical characterisation. Each column is represented by a total of ten samples. Polished sections, prepared from the samples, were studied by optical microscopy, scanning electron microscopy, electron microprobe and X-ray diffraction techniques. Mineral quantities were determined based on linear mixing models of whole rock and mineral compositions. Pyrite particle sizes were measured by image analysis interfaced to an electron microprobe. The tailings are coarse-grained (ie 96 per cent passing 75 ¦m) and composed of quartz, K-feldspar, muscovite and pyrite. Pyrite is homogenous and occurs as liberated particles displaying angular to subangular boundaries with strong dissolution features at the end of the leaching experiments. Based on up to 3518 particles measured in a sample, pyrite particle sizes range from 1.7 to 78.6 ¦m. Pyrite concentrations vary from 0.1 to 7.8 wt per cent, depending upon their location from the top of the columns. These correspond to pyrite losses of up to 99 per cent from their original level of 7.2 wt per cent in the upper half of the columns. Pyrite oxidation rates in terms of moles of pyrite oxidised per mole of pyrite per square metre per second were calculated from the effluent data and the measured pyrite particle sizes. The rates vary from 1.71+10-12 to 5.78+10-10 mole+m-2+s-1 within the 1.5 to 3.5 pH range for 10 ¦m particles. These results are comparable with the published oxidation rates at pH 2 where the dissolved oxygen is the only oxidant.

Jan 1, 2003

For the last decade Australia has been the leading exporter of both steam and coking coal. In the ten-year period 1989 - 1998 steam coal exports increased by 93 per cent and metallurgical coal exports increased by 50 per cent. However, profitability of the steam coal sector has been disappointing. The coking coal sector, especially the hard coking coal segment, has fared better but its profitability was more because of its ability to maintain relatively high prices rather than its inherent productivity. Until quite recently the Australian coking coal sector was widely expected to be able to maintain this comfortable state without undue effort for the three major æpartnersÆ; the companies, the State Government and the unions. But coking coal could now be heading down the path followed by steam coal that ends with long-term over-supply and, despite steady improvements in productivity, poor profitability. Steam coal entered the ænewÆ era of long-term over-supply some years ago. Over-supply was due to the rapid increase in production in Indonesia, often from new mines and Australia. AustraliaÆs production rise was underlain by the apparent belief that the best way to lower costs was to increase production. In the first couple of years costs didnÆt fall much but the additional tonnage was sold at lower and lower prices into the spot market. By mid-1998 the difference between the contract price set with Japanese utilities and spot sales was often in excess of $US12 per tonne. Japanese contract prices and tonnages have since fallen significantly. Steam coal has moved from being a product to being a commodity. Any profits are due more to the low Australian dollar rather than inherent mine productivity. Seaborne coking coal trade has been dominated by Australia, Canada and the USA, with the USA becoming less competitive. Unfortunately, when the Queensland capacity expansion was well down the pipeline, the Asian financial crisis occurred and the Japanese economy entered what appears to be a long-term recession. Contract prices fell 18 per cent, tonnages decreased and some mines have been reclassified as supplying lower priced coking coal. The paper analyses past and expected future trends in labour and mine productivity, rail freight and FOB export port cash and total costs of the Australian steam coal and coking coal sectors and discusses the market outlook for Australia. The future economic viability of the industry is analysed and discussed in the light of the rapidly changing global environment.

Jan 1, 2000

By G N. Musafer, M H. Thompson, R C. Wolff, E Kozan

The most important aspect of modelling a geological variable, such as metal grade, is the spatial correlation. Spatial correlation describes the relationship between realisations of a geological variable sampled at different locations. Any method for spatially modelling such a variable should be capable of accurately estimating the true spatial correlation. Conventional kriged models are the most commonly used in mining for estimating grade or other variables at unsampled locations, and these models use the variogram or covariance function to model the spatial correlations in the process of estimation. However, this usage assumes the relationships of the observations of the variable of interest at nearby locations are only influenced by the vector distance between the locations. This means that these models assume linear spatial correlation of grade. In reality, the relationship with an observation of grade at a nearby location may be influenced by both distance between the locations and the value of the observations (ie non-linear spatial correlation, such as may exist for variables of interest in geometallurgy). Hence this may lead to inaccurate estimation of the ore reserve if a kriged model is used for estimating grade of unsampled locations when non-linear spatial correlation is present. Copula-based methods, which are widely used in financial and actuarial modelling to quantify the non-linear dependence structures, may offer a solution. This method was introduced by Bßrdossy and Li (2008) to geostatistical modelling to quantify the non-linear spatial dependence structure in a groundwater quality measurement network. Their copula-based spatial modelling is applied in this research paper to estimate the grade of 3D blocks. Furthermore, real-world mining data is used to validate this model. These copula-based grade estimates are compared with the results of conventional ordinary and lognormal kriging to present the reliability of this method.CITATION:Musafer, G N, Thompson, M H, Kozan, E and Wolff, R C, 2013. Copula-based spatial modelling of geometallurgical variables, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 239-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By M A. Ohsberg, A C. Robertson

Quarrying in Australia accounts for a total annual production of around 200 Mt/a of sand, aggregate and materials used in construction. This material has an annual value of the order of $2 billion and, combined with transport costs of a further $1 billion, the annual value of quarry products are in excess of $3 billion. Currently all of the production of construction materials in Australia is from open cut quarrying or dredging. This paper focuses on the extraction of material by underground mining methods, termed æunderground quarryingÆ. The paper considers a case study for future underground development expansion of the existing open cut Mt Coot-tha quarry, located 5 km from the centre of Brisbane, Queensland.

Jan 1, 1999

By N McIntyre, J Smart, J Ossa-Moreno, D Rivera

Hydro-economics is a field of research that analyses water resources from a multi-disciplinary approach (Harou et al., 2009). These models generally include one component that describes the water resources of the catchment being analysed (e.g. the physical behaviour of water), an economic component that describes users’ water demand function (changes of willingness to pay relative to availability) and a coupling methodology. These models go beyond calculating cash flows for water investments and analyse the economic behaviour of users when facing water shortages or surplus. In other words, water demand curves are defined for each water user (e.g. urban, agriculture, mining, environmental and hydropower), and they are used to retrofit the water resources component. As a result, the model approximates the catchment scale response to droughts and wet periods, including the effects of water markets, restrictions, recycling, water sharing and any cooperative efforts by users to adjust to changing climate conditions.These models are usually focused on agriculture and urban users, the main water consumers in most catchments, but they have sometimes included environmental, industrial and hydropower users (Bekchanov, Sood, & Jeuland, 2015). Nevertheless, although a relevant user of water in several catchments, the mining industry has been rarely included. This paper is part of an ongoing project that addresses this gap by developing a hydro-economic model in the upper section of the Aconcagua River in Chile. The aim of the paper is to analyse the sensitivity of the outputs of the model to changes in input data, both hydrological and economic, and to develop insight on usefulness of such models for reducing water conflicts in mining regions.CITATION:Ossa-Moreno, J, McIntyre, N, Smart, J and Rivera, D, 2018. Sensitivity of a hydro-economic model in a mining region to changes in hydrological and economic inputs, in Proceedings Life-of-Mine 2018, pp 52–55 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

The basic model for the evaluation of any coal-bearing property is the cash flow projection, the major components of which are operating costs, capital charges, taxation and revenue. A range of cash flow projections can be produced by varying the assumptions which underlie the operating costs, by assuming various forms of capital funding, by making assumptions as to future taxation and by speculating upon the present and future market value of the product. As for any model, the informational inputs and assumptions are vital because, no matter how sophisticated the processing, the informational inputs and assumptions cannot be improved by it. That is to say, the validity of the output (the total evaluation itself) cannot be of greater certainty or significance than that of the inputs. The total evaluation can of course be expressed in a number of ways such as the Discounted Cash Flow (D.C.F.) Rate of Return, the Net Present Value or, the Payback Period. The foregoing statement may seem trite. However, it is necessary to be clear about it so as to avoid unnecessary complication and a preoccupation with techniques as opposed to the informational inputs and assumptions. So far as techniques are concerned, much has been written and said about them during the last decade. Most of us have heard, if not always understood, something about probabilistic models, Monte Carlo simulation, sensitivity and risk analysis to say nothing of inflationary costing and the relative merits of developing cash flows in terms of current or constant money. Those techniques have their value, particularly if they can serve to illuminate conclusions which could not be reached on a simple and even perhaps on an intuitive basis. I am, however, reminded of one major coal mining project in which 20 or more major variables were identified, many cash flow projections were run on the computer and a detailed sensitivity analysis was carried out. The major conclusion reached was that the D.C.F. Rate of Return was predominantly sensitive to variations in selling price and operating cost. Of course, the funding and fiscal elements of a cash flow projection have to be dealt with as rigorously as possible. However, in the development of any coal property, capital requirements and taxation are, in part at any rate, dependent upon the assumed operational parameters. If the latter are misjudged, the whole evaluation process is deeply affected. The same is true of revenue, in the sense that, the positive cash flow is a function of output as well as selling price and again, misjudgements about achievable and maintainable levels of production also deeply affect the final evaluation. I shall try to underline the fundamental influence of the technological factors upon lead times, capital costs, operating costs, taxation, funding and the achievable and maintainable levels of production. In turn, these affect the whole question of coal property evaluation and indeed, the likely success or failure of any coal mining venture. I make no apology therefore that this paper does not set out to discuss the more esoteric aspects of the evaluation process but rather, directs attention towards some of the informational inputs and assumptions which merit clarification and discussion.

Jan 1, 1975

The Kelian gold mine which was developed in East Kalimantan Indonesia in 1990 - 1992 is scheduled to complete mining and processing operations in 2004. This will have a major impact on the neighbouring communities who have benefited from the jobs, economic activity and infrastructure development which has been generated by the mine. Currently, there are no formal regulations or standards specifying the procedures for relinquishment of mining leases in Indonesia. Furthermore, a move towards regional autonomy, providing greater authority and responsibility to local (regional) areas, has recently been implemented in Indonesia and limited capacity exists in the new regional governments. Consequently, in October 2000, Kelian Equatorial Mining (KEM) initiated a partnership with the local community and government to explore sustainable post-closure options for the mine site and community development programs. The Kelian mine closure strategy seeks full involvement of all stakeholders through the Kelian Mine Closure Steering Committee (MCSC) in the development of sustainable solutions which will enable communities to secure long-term benefits and minimise post-closure risks from the KEM operations. This organisation, jointly chaired by the Head (Bupati) of the regional West Kutai government and the KEM President Director, with representatives from the local communities, governments and NGOs, has developed a Charter, a website and evaluation criteria to ensure accountability and transparency. There are four technical working groups, consisting of representatives from the mine, local community leaders, NGOs, Universities, Local, Provincial and Central Government Departments, which report to the Steering Committee. These working groups have researched, developed and recommended sustainable options to the Steering Committee. The MCSC has met quarterly to examine options in accordance with the criteria set out in the Charter and has endorsed sustainable solutions which have support from Government, Community and the mine. This paper describes the closure risks, sustainable outcomes derived through the Kelian mine closure steering committee process and outlines the methodologies used to develop and endorse sustainable solutions in a society with limited capacity undergoing enormous change and uncertainty.

Jan 1, 2003

By B Godel, E R. Ramanaidou, M Verrall

Fortescue Metals Group Ltd Iron Bridge (IB) operation is a magnetite deposit located in the Pilbara region of Western Australia situated around 145 km south of Port Hedland. This Mesoarchean deposit belongs to the 3230 Ma Pincunah banded-iron formations (BIF), a member of the Kangaroo Caves Formation, Sulfur Springs Group (van Kranendonk, 2000).

Sep 18, 2023

By J P. Moodie

Recent trends in flotation technology are briefly reviewed. These show that considerable development has been made as the operators, suppliers and technologists have responded to the challenges of the industry. Most of these advances have been based on empirical and phenomenological methods. There is a considerable opportunity to make further advances through a more fundamental, scientific approach. Some of this work is discussed and, although progress is being made on this front, industrial uptake has been somewhat slow. A number of specific issues facing the industry are discussed.

Jan 1, 2005

By R Barritt, P Scott

Across the globe, it is a common scenario that tailings storage facilities (TSFs) are being decommissioned; however, their subsequent impact on the local environment and landscape can often be overlooked during the mine planning process. In addition, the requirement of a cover system for a facilities closure may not be a priority until the latter stages of the mine/mill operation when potential cover materials may have been utilised elsewhere or, worse, buried. Developing a conceptual design and closure plan for a TSF early in a mining venture is fundamental to its success once operations have ceased. If a cover system is a planned component for rehabilitation of a TSF, it is vital that its design is appropriate to the facility and any local site constraints, such as climate and cover system material availability. It is also strongly recommended that various cover system options are physically trialled at the site by using performance-monitoring instrumentation. Through this process, an informed decision can be made regarding the most appropriate cover system design to meet any regulatory and stakeholder closure objectives and criteria specific to the site in question; however, in order for the cover system’s performance to be determined through on-site trials, it is essential that an appropriate instrumentation design is utilised. Often, little attention is paid to the data that is being obtained, and its importance may only become apparent after several years of monitoring at an expense to the venture. This should not be the case. Many sites have used an appropriate initial planning stage to understand what is required for the successful closure of a TSF, how it can be achieved and how monitoring data can be utilised to prove, or otherwise, that a cover system design will be a success.CITATION:Barritt, R and Scott, P, 2015. Cover system performance monitoring for tailings – are we doing it correctly?, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Czerwinski, M Kasper, M Wyser, N Heeb

The VERT project 1993 - 1998 laid the technical foundation for curtailing the emission of fine particles from diesel engines at Swiss underground workplaces. The targeted maximum was 100 ¦g/m3 EC. Extensive laboratory and field investigations demonstrated that this specification is only attainable with modern diesel particulate filter (DPF) systems that almost eliminate particles in the entire lung penetrating size range from 20 nm to 2.5 ¦m. In January 2000, Switzerland mandated compulsory particle filters in underground workplaces, particularly in tunnelling, irrespective of engine age, size and type. After the implementation, the particle concentration in the respiratory air was below 40 ¦g/m3 EC, compared to earlier values of up to 750 ¦g/m3 EC. Deployed DPFs have proven filtration rates of 99 per cent in the entire size range of alveoli intruding particles. The DPFs are as durable as the engine, suffer no ageing and require minimal maintenance. The failure rate is below three per cent annually. Of the 6000 retrofitted construction machines in Switzerland, about 400 are deployed underground. Prerequisites for this quality are a sophisticated certification procedure, electronic monitoring of DPF operation and meticulous periodic exhaust gas inspection of the engines.

Jan 1, 2005

By H P÷llmann

Calcium aluminates, calcium aluminate ferrate and calcium aluminate sulfate were synthesised by solid-state reaction, sol-gel method, a self-combustion method and by a polymeric precursor process. For chemical sintering methods the base chemicals CaO, CaSO4, Al2O3 and Fe2O3 were used. As precursors for sol-gel synthesis metal nitrate hydrates and Al2O3-Sol were used. In order to synthesise pure phases by a self-combustion reaction glycine was used as fuel and nitrates as metal components. In the polymeric precursor process metal nitrates and diluted H2SO4 were used as metal components and the resin was made using citric acid (C6H8O7) and ethylene glycol (C2H6O2). Precursor phases synthesised by these different methods were sintered step-by-step in order to investigate the crystallisation. Further on single phases were hydrated and their hydration behaviour was studied by heat flow calorimetry, X-ray diffraction and cryo-transfer scanning electron microscopy. Due to the different synthesis procedures different hydration reactions and microstructures of the phases will be shown.

Jan 1, 2008

The paper examines the difficulties encountered by objectors to mining privilege applications. It describes the various involvements of the environmental defence society in the mining controversy and makes some comment on the proposed amendments to the Mining Act 1971.

Jan 1, 1981

By Terry G. A B

Before detailed design of Museum Station could commence, a number of factors had to be considered to determine its exact location within the city street pattern, the depth and the dimensions of the underground station. To arrive at a sound con- clusion regarding location, the relationship of the station to probable future city development had also to be considered.

Jan 1, 1981

By P J Savory

Ranger is a uranium mining operation located within one of the most environmentally sensitive regions of Australia. Geology has played an important role in mine planning, operations and rehabilitation since discovery of the deposits 25 years ago. The Ranger orebodies have a reserve total of 166 300 tonnes of U308 including 90 400 tonnes of U308 at North Ranger. At current milling rates these reserves give a mine life greater than 40 years. The uranium is hosted in Lower Proterozoic rocks of the Cahill I ormation and is associated with strong chlorite alteration. In pit grade control involves the use of calibrated probes and a radiometric truck discriminator allowing fast, accurate grade determination of material. Ore is defined at a cut-off grade of 0.2 per cent U308. Mineralised material is defined by the Uranium Mining (Environmental Control) Act 1979 (UMEC Act) at a grade of 0.02 per cent U30s. Natural water levels in the #1 Pit area vary as much as 7.5 metres between wet and dry seasons. Ground water inflow into the pit during the dry season is 600 m3/day. No significant slope failures have occurred in the pit. The environmental impact of mining operations is constantly monitored. Rehabilitation of non-mineralised stockpiles is ongoing. This paper discusses the interaction between geology, hydrogeology, rock mechanics and grade control with the present mining operation.

Jan 1, 1994

By C A Heinrich, Morse M. P, Cruickshank B. I, Pyke J. G, Whitaker A

Very little public domain information is available on the exploration signature of the Coronation Hill Au+Pd+Pt deposit. From 1987 to 1990 the BMR (now AGSO) carried out geological, geophysical and geochemical (whole-rock, stream, soil and rock chip) surveys within the South Alligator and Kakadu Conservation Zones and defined several key parameters useful for exploration programs. The essential geological ingredients for the style of Coronation Hill Au+Pd+Pt¦U deposit are oxidised, low pH fluids, dilatant fault structures, a thick neutral to oxidised cover sequence and chemical traps in the basement. In geophysical data, the areas surrounding the mineralisation can be detected by airborne magnetics as major lows in magnetite-rich rocks, whereas in airborne gamma-ray spectrometry data, imaged spectrometric channel ratios such as U2/I'h and U2/K highlighted alteration surrounding the deposits. Three types of stream-sediment and soil samples were taken from each site: (1) -1 mm mesh, 5 kg sample for bulk cyanide leach (BCL) analysis for Au, Pd, and Pt; (2) 1 kg sample of -1 mm mesh sediment for fire assay/ICPMS analysis for Au, Pt and Pd; and (3) 50 g - 180¦ mesh sample for a variety of trace element analyses, including Au, Pd and Pt. Techniques 2 and 3 gave similar results for Au, Pt and Pd, while the recovery rates for Pd and Pt from the BCL samples were considerably lower. Other trace elements did not define unique indicators for Pt or Pd mineralisation, as each sample reflected the dominant lithology in the drainage basin. Rock chip surveys were useful in determining which faults were associated with the ore fluid in regions of multiple fracturing. Results from these exploration-style surveys also confirmed that the Coronation Hill deposit is a variant of the unconformity-style of mineralisation, as all significant geochemical and/or geophysical results occur at or below the unconformity.

Jan 1, 1994

By G R. Hancock

A common and cost-effective method for post-mining landscapes is to construct linear hillslopes with a break in the hillslope at appropriate distances to reduce hillslope length and resultant erosion risk (Figure 1). The break in slope occurs at a point that has been found by local experience to be appropriate for the materials and climate. Further enhancement of the linear hillslope may be assisted by surface treatment such as ripping (Saynor, Lowry and Boyden, 2019) (Figure 1). Firstly, ripping introduces surface roughness which breaks up flow paths reducing flow velocity thereby reducing erosion potential. The depression produced by the ripping acts as a trap which captures water, sediment and organic matter

Aug 2, 2023