Search Documents

Aspects of the formation, decomposition and acid solubility of zinc ferrite were examined to find potential ways of increasing the recovery of zinc from a calcination process of mineral concentrates. Ferrite can begin to form within 2 hours at 450¦C. while complete reaction can occur after 35 minutes at 700¦C. The nature of the starting materials has a pronounced effect on the rate of formation and below 700¦C. ZnSO4 and Fe2O3 proved to be the least reactive of the materials investigated. It is possible that iron in a mineral admixed h sphalerite can be converted to a relatively inactive form, however, it does not seem possible to prevent zince f formation when iron is in the sphalerite lattice. At the two temperatures examined, 650¦C. and 700¦C, the presence of SO2 in the atmosphere accelerate .e formation of ferrite. Prolonged exposure to such atmospheres, however, caused the ferrite to decompose to ZnSO4 and Fe203. The optimum temperature for decomposition was 650¦C. and it was virtually complete within 2 hours in an atmosphere of 10% SO2 in air. Zinc ferrite was also decomposed by CO at low concentrations, and by heating with limestone at 1000¦C. for at least 2 hours. The solubility of zinc ferrite in acid was influenced by the starting materials used. As both the reaction temperature and the time at temperature increased the acid solubility decreased. The acid solubility was a minimum when the ___i_.. n - I -r~...................c -..... F, fe..i+e --A frn... A01- +^ Z(lo/

Jan 1, 1970

From the viewpoint of mechanical efficiency, charges should be fully coupled and, upon detonation, should just fail to break the rock in compression. But because mining thrives on its cost-effectiveness rather than its mechan- ical efficiency, the explosive which generates maximum energy per $ should generally be used, even though the mechanical efficiency of this explosive's detonation products may be sub- optimum. Wherever possible, each charge should have a length:diameter ratio of about 20 or more and should shoot to a concavely biplanar free face that is both parallel and reasonably close to the blasthole. Success in obtaining parallel effective faces often demands the drilling of angled blastholes and, hence, will require intensified research and development efforts by drilling manufacturers, especially where hard strong rocks are encountered. Blastholes should be drilled on equilateral triangular grids and fired in a Vl or shallower V-type sequence using inter-row delays which ensure that good pro- gressive relief of burden is achieved. The conventional method of calculating Se/Be values (on the basis of planar effective faces) is often invalid.

Jan 1, 1986

By Windsor C. R, Thompson A, Bywater S

A new high tensile strength, steel cable, that may be grouted into boreholes has been developed for use as rode reinforcement. The manufacturing technique produces a birdcage pattern in which the cross section varies along the length of the cable. The load transfer from cement grouts to birdcage cables has been demonstrated in laboratory tests to be better than that of standard 15.2 mm diameter seven wire cables. The manufacturing process also allows for a wide range of capacities which may be specified by design engineers. The various birdcage cable configurations have been applied as rock reinforcement in a number of Australian underground and surface mines.

Jan 1, 1990

By L Lorenzen, H Muller

"Every year a large number of projects are evaluated by small listed and unlisted mining companies that are hoping to find the ideal project, which will catapult them from a mining junior status to that of a mid-tier mining company. Usually this includes finding the æidealÆ or ærightÆ orebody and then developing a process which will allow cost-effective recovery of the valuable metals and the production of a saleable product. These dreams are seldom realised and there are a number of good and obvious reasons for this. Issues that are generally high up on the agenda for the smaller companies are: cost of developing a project before the feasibility study stage finding a suitable, or optimum processing technology financing of the project dealing with risk.The most expensive part of the development process for the small miner is often the exploration side of the business and finding the æidealÆ orebody. However, finding the right orebody will not be discussed in this paper. The æidealÆ orebody does not necessarily solve the problems of the mining junior, as much of the uncertainty lies in the process required to recover and produce the final metal product. Once a mineralised deposit has been identified and the grade at least reasonably qualified, the development of a suitable process becomes the driver to convert the deposit into an orebody. This paper proposes that a small exploration company has a very limited opportunity to succeed if it does not do sufficient homework before it identifies the æidealÆ orebody. The risk profile for the small mining company, by its very nature, has to be different to that of a major company and as a result the opportunities often lie in managing different and often new process options, which may be the key to bring such projects on line successfully.CITATION:Muller, H and Lorenzen, L, 2012. Project selection and process development for mining juniors, in Proceedings Project Evaluation 2012, pp 149-158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By Costello MC

An alternative process for desorbing and recovering metals from activated carbon has been developed, and is the subject of several patent applications by Micron Research (W.A.) The system uses the principle of conditioning the carbon in a strong alkaline cyanide solution followed by distillation desorption in a fractionating column, using the carbon as the column packing and methanol as the desorbing agent. The system offers the following advantages : (a) The processes of desorption, methanol recovery and reactivation are all carried out in a single column with the carbon itself acting as the column packing. No other desorption plant items or fractional distillation equipment are required. (b) The metal values are concentrated into the water content of the carbon and no other water is used except as condenser coolant. This produces very high grade gold silver solutions which give high current efficiencies in the electrowinning step. These high gold concentrations allow almost complete separation of gold and silver from copper in the electrolytic cell. (c) The process is completed to a tailing assay of less than 200g Au/tonne carbon in 15 - 20 hours allowing turn around of carbon batches on a daily Basis.

Jan 1, 1982

The Mount Sisa orebody on Misima Island, P.N.G., consists of goldsilver mineralisation associated with massive carbonate and amorphous iron-manganese oxides in fractures and breccia matrix. The orebody forms the northern extension of the Umuna deposit, which lies within a three kilometre strike length of a northwest trending, 300 metres wide, high angle fault zone. The structure is deeply oxidised, with the magniferous oxide material resulting from oxidation of carbonate. The wallrocks are metamorphosed basement psammopelites and basic volcanic rocks, extensively intruded by microgranodiorite. These are dominantly epidotised and sericitised. The precious metals are associated with anomalous Cu, Zn, Pb, Mn, As, Ba, Ga, Sb, and Mo. Many of the features of the Mount Sisa mineralisation are characteristic of volcanic-hosted epithermal deposits of western North America.Lithologic and textural gradation is observed between the carbonate hydrothermal breccia-fill at Mount Sisa, and the quartz dominated brecciafill and dilational fracture-fill mineralisation which forms most of the Umuna deposit to the south. This gradational relationship is analogous to that in the Amethyst-OH vein system at Creede, Colorado, where it is shown to be indicative of deposition from laterally migrating fluids.

Jan 1, 1988

If a straight line should be drawn on the map (Fig 1) through the northern half of the South Island of New Zealand, from Mt. Domett in the north to Arthur's Pass in the south, and another line drawn parallel to it and at a distance of ten miles to thewest, according to the topographic scale, it will be found that within the belt thus drawn across the country all the most important mines, past and present, of the outh Island are situated, with the exception of a few in Otago.The most important product of this tract being gold, and Reefton, the most important southern mining field, being situated at about it central portion, the zone may aptly be termed 'The Great Reefton Gold Belt.'The occurrence of so many gold mines along this particular strip of country is not at all a matter of chance, but is the outcome of cause and effect. Running along the eastern side of the gold belt are the Brunner and Victoria Ranges, which are chiefly composed of crystalline schists and metamorphic granite of probably Cambrian or Silurian age; between these and the gold-bearing series there are interposed at one or two places some beds of slates, limestones, and cherts of Devonian age, characterized by the brachyopods Spirifer...

Jan 1, 1911

By Szwedzicki T

Uniaxial testing was performed on model pillars to determine the effect of width to height ratio on pillar and surrounding rock mass stability. Samples were modelled in a shape similar to that of dumbbell weights, with the centre representing

Jan 1, 1994

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Selby DW, Hamill J, Cauley ID, Thomas I, Thornton AJ

The main objective of sulphide flotation in a cassiterite concentrator is to remove sulphide minerals (pyrite, pyrrhotite and sometimes chalcopyrite) from the ore prior to gravity concentration. Tin losses in the sulphide flotation stage account for a significant proportion of the total tin loss. separate studies of the sulphide flotation circuits of Renison Ltd and Cleveland Tin Ltd were conducted to investigate reasons for the tin losses. Sampling surveys were conducted in the rougher-scavenger and also the regrind-cleaner sections of both plants. In both plants, the rougher circuits recover excessive quantities of liberated cassiterite, while recovery of the desired composite cassiterite-sulphide fraction is low. The regrind mills are successful in liberating the composite cassiterite in the rougher concentrate, but at the expense of increasing the proportion of very fine tin mineral. The cleaner circuits recover between 40 and 60% of the cassiterite received, and this is all lost.

Jan 1, 1978

In the hard rocks of the Nordic countries of Norway, Sweden and Finland underground works have a long tradition. Today the subsurface has been taken into use for a wide variety of purposes. In this paper only the more uncon- ventional examples are described such as caverns for drinking water, sand bunkers, molasses silos, wine and liquor stores, cold stores, heat storage, waste disposal and state archives. The particular use of unlined high pressure tunnels and socalled air-cushions for hydropower schemes is discussed. The dual use of subsurface air-raid shelters for sports activities seems to be a special Nordic tradition. Some cost figures are given and the advantages of using the underground is Discussed.

Jan 1, 1987

By Rosengren KJ

Geotechnical conditions often have a critical influence on the design of new open pit and underground mines, but they are often considered of secondary importance in relation to other factors, such as detailed geology, orebody geometry and grade distribution. As a result, geotechnical studies may not be carried out during early project investigations or, at best, may be given only superficial attention, often to the overall detriment of the project. Technically and economically, it is logical that geotechnical studies should be integrated with geological investigations as soon as it becomes evident that the particular deposit may prove to be economic. The paper discusses the use of geotechnical information in the selection of mining methods and mine design for underground mines and for wall design and assessment of excavation characteristics in open pit mines. It then considers methods of obtaining the relevant data, with particular reference to exploration boreholes. Selected case studies on the application of geotechnical data to mine design are Included.

Jan 1, 1986

By S DeKruijff

The Mount Isa Mines Copper Mine in Mount Isa started producing copper in 1966. The Copper Mine gradually increased production rates to nearly six million tonnes per year. Over the last three years the mine has been in a gradual ramp down due to the reduction of primary ore sources and head grade. The majority of ore sources are predominantly in pillar retreat sequences bounded by multiple fill masses. There also a substantial lower grade resource delineated to the south of the main orebody. These remaining ore sources present significant engineering challenges to obtain a safe and cost-effective extraction. Stope designs have become increasingly complex and require additional engineering and operations input and analysis. This paper describes the major planning and operational challenges and issues associated with the stope design and extraction of an orebody in the later stages of mine life.

Jan 1, 2000

By Fejes A. J

The U.S. Bureau of Mines installed surface and subsurface instruments at a mine site in Colorado to monitor and characterize the overburden response to longwall mining. Instrumentation included a time-domain reflectometry (TDR) cable, a multiple-point borehole extensometer (MPBX), vertical- deformation surface monuments, and in-mine pressure cells for monitoring abutment, pillar, and gob loads with respect to the longwall face position. The purpose of the study was to collect data that could be analyzed to correlate the design of the mine layout to the resulting overburden failure response. Determining the extent of caving and fracturing is important in the and and semiarid Western United States because of the possible consequences to the fragile underground hydrologic systems upon which the land owners and users depend. This study is unique from past investigations because the overburden contains massive sandstone members that impose special conditions on the caving process and pressure redistribution above the longwall panels. This paper presents the results of this correlation study.

Jan 1, 1992

By Perring CS, Vearncombe J. R, Ho SE, Groves DI

Large Late Archaean greenstone belts in Western Australia, Canada and Zimbabwe, contain abundant mesothermal gold, volcanogenic massive base-metal sulphide, and komatiite-associated Ni-Cu mineralization. These greenstone belts are similar in many respects to convergent and accretionary plate margins found in the Pacific rim; modem environments which are cor-respondingly rich in gold and base-metal mineralization. The giant gold placer deposits of the Late Archaean Witwatersrand Basin (the world's largest gold producer) formed in a foreland or retro-arc basin; in a similar tectonic setting to much modem placer mineralization around the Pacific. Gold and volcanogenic base-metal sulphide mineralization are abundant in Late Archaean terranes and the Pacific rim because1. gold mineralization is a product of convergent margin tectonics, and 2. accretion in convergent margin orogens provides the best chance of preserving base-metal mineralization related to submarine volcanism.It is therefore likely that the abundance of gold and base-metal sulphide mineralization in the Late Archaean reflects the widespread growth and sta-bilization of continental crust via tectonic processes broadly similar to those operating in the present Pacific basin.

Jan 1, 1990

Lungfish and crayfish inhabit continental ecosystems similar to those of their ancient counterparts in the Permian (lungfish) and Triassic (crayfish) Periods, exhibiting similar burrowing behaviors to live, breed, and escape desiccation. Identification of their burrows in the geologic record when body fossils are absent has relied on the overall gross morphology of the burrows and the process of elimination. A method of burrow identification has been developed by evaluating burrow structures in an attempt to designate architectural and surficial burrow morphologies that uniquely reflect the distinctive burrowing mechanism of a particular organism. The information from this method defines the burrowing signatures of an organism, enabling the differentiation of their burrows even when fossil evidence is lacking.The lungfish constructed simple, vertical burrows with bulbous terminations. The burrow walls exhibit fine, horizontal to sub-horizontal striae and vertical to sub-vertical striae near the top of the bulbous terminus, reflecting a burrowing style similar to modern burrowing lungfish. The crayfish constructed simple, vertical burrows to complex burrows with multiple branching and chamber development. The burrow surface ornamentations exhibit horizontal to sub-horizontal ridges, vertical to sub-vertical groupings of scratches, mud- and lag-liners, knobby and hummocky textures, and body impressions, which reflect the burrowing mechanism of the crayfish.

Jan 1, 1990

The industrial practice of separating finely' around valuable minerals from associ- ated gangue materials by froth flotation is well known. Despite the obvious importance of this industrial process, the predictive tools for plant engineering evaluation of flotation process variable changes are still in a developmental stage. Consider, for example, the situation where an operating engineer is faced with evaluating a change in an existing chemical reagent scheme, possibly based on batch laboratory data. When all is said and done, the engineer must still perform detailed physical testing of the proposed reagent change on the actual equipment in plant use to be confident even of the direc- tion of change of plant results, let alone the economic viability of the change. The theory behind chemical reagent behaviour in froth flotation has been studied extensively, e.g., (Aplan {1980}, Fuerstenau {1976}, Fuerstenau {1962}, and Somasundaran {1980}), and, certainly, important progress has been made. Unfortunately, the nature of the flotation process, with its complicated heterogeneous surface chemisty activity operating on highly variable and difficut to characterize ore surfaces, coupled with com- plex mass and momentum transfer phenomena, :;l riously compromises the plant scale predictive capability of theoretically based models.

Jan 1, 1978

By F Clark, J T. Carswell

Ore definition for final stope planning is often a challenging prospect in underground (UG) gold mines which exhibit high geological and grade variability. Unlike the grade control (GC) scenario in an open pit (OP), the ability for the mining geologist to plan a sampling campaign which effectively characterises the underlying mineralisation is fraught with difficulty. UG sampling patterns are strongly clustered and typically not dense enough to characterise the spatial and statistical properties. Very commonly, sample volumes are not large enough to provide a reliable grade estimate of the surrounding rock. These factors critically affect our ability to accurately map out ore positions and estimate metal quantities.At Sunrise Dam, traditional UG sampling and modelling techniques have proven to be an unreliable strategy for successful stope planning and extraction. The problem was first observed during the final cut-back in the open pit for which the mineral resource model was constructed from UG diamond drilling. Open Pit grade control reconciliations were strongly positive for both tonnage and grade compared to the resource model. Underground workings missed significant quantities of ore which was laterally defined by open pit reverse circulation (RC) GC drilling. Upon examination it was realised that the cause of the problem was one of inadequate sample density and sample support, the implications of which potentially affected the entire UG mine.As part of a broader study into underground grade control procedures, detailed reconciliation of initial stope production from the GQ domain also pointed to inadequate sampling as a major constraint to effective grade control and reserve conversion.To overcome this deficiency, dense 115 mm wet RC grade control drilling and conditional simulation modelling has been successfully implemented with the intent to replicate the grade control process in the open pit. The increase in sample density and sample volume has proven to be a very effective tool for mapping out highly complex mineralisation. A marked improvement in stope definition, reserve conversion and Mine to Mill reconciliations has been demonstrated on the back of an innovative approach to UG grade control.CITATION:Clark, F and Carswell, J T, 2014. Using reverse circulation drilling to improve sampling in a complex underground gold operation – an innovative approach to underground grade control at the Sunrise Dam Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 143–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Koppe J. C

This study presents the procedure of mine modelling and reserve evaluation by means of statistics, computer interpolation methods and aerophotography interpretation. All data are from Carbonifera Treviso, Laura Muller City, Santa Catarina State, southernmost Brazil. From 22 bore holes and nine trenches opened in the coal seam outcrops, a data base including level references and thickness of all rock formations was created.Using this information, basic statistic analysis was carried out, showing that there are three different populations (three modal distribution). These populations defined three geological blocks with different characteristics of overburden removal and mining methodology. This mathematical approach for analysing geological data is very important for correct mine planning and complementary prospection.

Jan 1, 1993

By Hayward SB

The Maragorik prospect is an example of high sulphidation, Cu/Au mineralisation occurring at a high level in the hydrothermal system. As extensive ash deposits blanket the region, controlled-source audio magneto-tellurics (CSAMT), in conjunct-ion with bulldozer trenching, have been used to delineate subsurface geology. Fluid upflow has occurred along EW structures dilated by rotation on the bounding major NW lineaments. Rising hydrothermal fluids have exploited permeable horizons in contact with the upflow structures. This lithological control is evident as ledges of silicification and peripheral clay alteration, at high levels in the system. As is typical of high sulphidation systems, a two phase fluid consists of an initial rapidly moving vapour-dominated phase, followed by a liquid-dominated phase. Much of the zoned and overprinted silica to clay alteration is developed from the vapour-dominated fluid. Mineral deposition occurs as a result of brecciation of the competent silic-ification by liquid phase fluids. Such mineralisation is of restricted volume in ledges proximal to the feeder structures.The style of alteration and mineralisation are indicative of a very low temperature and hence a high level system. Thus, although high sulphid-ation systems are inferred to develop from porphyry-related magmatic fluids, such a source at Maragorik is interpreted to be very deeply buried.

Jan 1, 1994