Search Documents

By Henry Seltz, Cyril Wells, Hugh J. MacDonald

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By Henry Seltz, Hugh J. MacDonald, Cyril Wells

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

THE increased demand for titanium alloys with improved high-temperature creep strengths has stimulated interest in silicon as an alloying addition to titanium. Silicon is a potent solid-solution strength-ener and, if added in sufficient concentration and properly heat-treated, can also dispersion-strengthen titanium by eutectoid decomposition.' However, better understanding of the nature and distribution of the resulting silicide dispersion in more highly alloyed titanium matrices is necessary for the development of useful titanium alloys which utilize the latter strengthening mechanism. This note describes the chemical and crystallographic characteristics of the silicide phase as it occurs in a typical high-temperature near-a titanium alloy matrix. Several Ti-6A1-3Sn-3Zr a11oys containing various amounts of silicon ranging from 0.1 to 1.0 pct were melted as 10- to 20-lb ingots and processed into 1/2-in.-diam bar stock. The microstructures of specimens annealed at various temperatures were conveniently summarized by the (Ti-6Al-3Sn-3Zr)-Si pseudobinary phase diagram illustrated in Fig. 1. Comparison with the Ti-Si equilibrium diagram indicates the substitutional solutes (Al-Sn-Zr) increase the eutectoid temperature and decrease the a terminal solubility. Annealing at temperatures sufficiently high to dissolve the silicon in a ß solid solution and cooling rapidly enough to preclude coarsening generally produced a uniform dispersion of fine silicide particles, whereas annealing at temperatures near but below the ß transus produced relatively coarse silicide particles. Annealing in the limited a, plus 3 region produced a duplex coarse and fine silicide array. Several a-annealed specimens were examined by X-ray diffraction to determine the crystallographic identity of the precipitate phase. Copper Ka X-ray diffraction patterns of bulk specimens which contained 0.5 and 0.8 pct Si were virtually identical to that of the silicon-free Ti-6Al-3Sn-3Zr base alloy except for a slight shift in some of the high-angle diffraction lines. Apparently the silicide volume fraction was too low to be detected in bulk specimens. X-

Jan 1, 1969

By A. K. Chakravarti, A. Lihiri, G. G. Sarkar

One primary objective of India's third Five Year Plan is the expansion of coal production. The goal: boost present output of 45 million tons to 95 million tons by 1965--an increase of more than 100 pct!

Jan 7, 1961

By Robert J. McKay, F. P. Huston, WILLIAM G. HUMPTON

THE manufacture of nickel-clad steel plate and the fabrication of articles from it has progressed far enough to permit a general description of the working methods used. The manufacture of sheets made up of layers of nickel and steel is not new as a sheet of this character was patented in Germany in 1893. Present development differs mainly in the size and finish of the product. The earlier light-gage highly finished products have been limited in their application due to their similarity, in certain respects, to electro-plated and highly finished alloy sheets. The new product is a relatively heavy plate 1/4 or 3/s in. thick and heavier, with one side coated with nickel, the weight of nickel being of the order of 10 per cent of the whole. The finish is that of hot-rolled steel plate.

Jan 1, 1931

By Walter Miller

NOW, after a year's continued impact of war, the task of the petroleum-refining industry stands out clearly and looms up in larger aspect. This time it is not, as it was so largely in the first World War, simply a matter of increased quantity- more and more of the same petroleum products that had substantially been standard for years. In this era the emphasis is largely on newer and improved materials which had been produced, if at all, in comparatively insignificant quantities, and for which manufacturing equipment was not available on a large scale. At the beginning of 1942 four great product needs (besides a number of lesser one-) confronted the industry: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for aviation and Army equipment service, and petroleum chemicals for synthetic rubber manufacture.

Jan 1, 1943

For handling rough rock, the shovel-train system is unexcelled. The ideal application is a physically large, but not excessively deep, open-pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transportation than will any other haulage method. Relatively gentle grades must be employed- usually 3% for uphill hauls and 4% for downhill hauls. The greater the differences in elevation the greater are the railroad track grade space requirements. By way of illustration, a 3% ramp out of a pit only 300 ft deep must be almost two miles long. Mainline track locations should be selected carefully so that the frequency of movements during the life of the mining operation is minimized. This applies both to ore and to waste haulageways. Such moves are not only expensive but difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semi-permanent trackage.

Jan 10, 1967

By George H. Deike

DURING the past year a survey was conducted by the Committee on the Promotion of Student Interest in Coal Mining to determine whether the program as laid down in past years was operating effectively. It is a source of satisfaction and pleasure to be able to report considerable headway among operating companies in putting cooperative scholarship plans into operation. In previous committee reports the pioneer work along this line by Eugene McAuliffe, president of the Union Pacific Coal Co., has been cited. That Company now has in its employ, in responsible positions, three men who received their education under such scholarship plans. One student under a similar plan is now studying at the Colorado School of Mines.

Jan 1, 1942

By CHAS. A. R. LAMELY

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varyng low dips in varying directions, and underlie large areas of the district. Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that sufficient tonnage existed to justify a redesigning of the whole operation, surface and under- ground. After four years of general study, the following program was planned :

Jan 1, 1949

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By Donald C. Myntti

INTRODUCTION A major segment in a successful heavy equipment maintenance and repair program is the provision of well-laid out and well-equipped shop and service facilities The facilities described here will be those required for a large, high tonnage hard rock open pit mine utilizing rotary drills, shovels, haulage trucks, support equipment, and service trucks. The term support equipment covers the equipment required to support the drill, shovel, and truck operations, these are crawler tractors, road graders, front-end loaders, water trucks, rollers, rubber-tired tractors, etc. Service trucks are the automotive type consisting of rubber-tired over-the- road equipment. The primary structures generally involved in the total maintenance effort are as follows. (1) the main shop with an attached warehouse (the structure could also house the tire and lube shops plus the equipment cleaning stalls), (2) a service station with bulk petroleum product storage tanks, (3) a heating plant, (4) a security station (lf this is a corporate requirement), (5) operating department and employee assembly buildings, and (6) an electrical substation. Under certain conditions, many of these facilities with the exception of the substation could be combined In one or several structures. This arrangement could have a great advantage especially in areas where the heating of the structures is extremely critical.

Jan 1, 1979

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 6oo,ooo lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaCO3) and dolomite (MgCO3CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent Si02, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 Si02 and 6.5 R203. The percentage reported as R203 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe203, A1203 and Ti02. The sorted magnesite product is not the best grade, even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1940

By J. H., R. W. Guard, Westbrook

In 1953 Kornilov and Mints' presented data on thermal expansion and electrical conductivity of the compound Ni3A1 which indicated the possibility of a transformation in Ni3A1 at about 600°C. The present paper gives results of some observations

Jan 1, 1960

THE activity of the principal oil fields of Rumania followed the same course as in 1939. It was marked by (1) collaboration between the various companies, particularly in exploiting oil at great depths with a view to rationalizing the exploitation and decreasing the difficulties inherent in very deep drilling; and (2) economy in the exploitation of the older pools in reducing to a minimum the cost of the extraction and working over of wells by the concentration of productive wells in groups. The pooling arrangement continued at Tintea as a measure of conservation, and exploitation of the unitized region went forward on the basis of the norms established in 1939. The same methods were applied in the fields of Liesti, Ceptura and Boldesti. The petroleum industry had some difficulty in providing the necessary material and the hands for work. Importation of material and machines from the United States was virtually stopped. Substitutes were provided from Germany but particularly useful were certain dispositions made by the local metallurgical industry. Despite the higher cost of the production of local material and machines, they were superior to the German product, the difference in quality justifying the higher price charged as the materials were found to be particularly adapted for the purposes of the petroleum industry. The cost of production was still further raised by the work that was imposed for national defense. The rise in costs per meter drilled was 50 per cent over those of 1939. According to bimonthly tables furnished by the Moniteur du Petrole Roumain, the deepest well completed in 1940 was an exploratory well, No. 201 of the Concordia company, drilled at Tintea and suspended at 3338 meters. This depth was reached toward the close of 1939 and the well was not deepened in 1940 became of large deviation from the vertical. The record for productive wells had been held by No. 429 at Tintea, drilled by Unirea to a depth of 3200 m., and in 1938 well No. 317 Cocorasti-Mislea, of the Colombia company, but these records were passed in 1940 by well No. 613 Liliesti of the Con-cordia company, which reached a depth of 3294 m. and had an initial production of 10 tons per day. In 1940, the same number of wells, II, had been drilled to a depth of over 3000 m. as in 1939. Five of these wells are at Tintea and six at Liliesti. Table I lists these very deep holes in the order of their depth. Table i.—Deep Wells Drilled in Rumania in 1940 Initial No. Produc- of Company Field Meters tion, Well Meters Tons per Day 405 Colombia......... Liliesti 3,001 10 629 Unireu............ Tintea 3,005 73 426 Unirea............ Tintea 3,050 48 410 Colombia. ........ Liljesti 3,055 30 627 Concordja (Unirea). Liliesti 3,072 75 430 627ConcordjaConcordia (Unirea). (Unjrea 3,II9 30 618 Colombia......... Liliesti 3,168 70 24 Steaua Romana. . . Tintea 3,184 18 412 24Unirea............ Tintea 3,211 23 613 Concordia......... Liliesti 3,294 10 Production in Rumania in 1940 reached 5,813,000 tons, in contrast to 6,~40,0oo tons in 1939, a decline of 427,000 tons, or 6.8 per cent. Drilling reached 241,500 m., in

Jan 1, 1941

THE activity of the principal oil fields of Rumania followed the same course as in 1939. It was marked by (1) collaboration between the various companies, particularly in exploiting oil at great depths with a view to rationalizing the exploitation and decreasing the difficulties inherent in very deep drilling; and (2) economy in the exploitation of the older pools in reducing to a minimum the cost of the extraction and working over of wells by the concentration of productive wells in groups. The pooling arrangement continued at Tintea as a measure of conservation, and exploitation of the unitized region went forward on the basis of the norms established in 1939. The same methods were applied in the fields of Liesti, Ceptura and Boldesti. The petroleum industry had some difficulty in providing the necessary material and the hands for work. Importation of material and machines from the United States was virtually stopped. Substitutes were provided from Germany but particularly useful were certain dispositions made by the local metallurgical industry. Despite the higher cost of the production of local material and machines, they were superior to the German product, the difference in quality justifying the higher price charged as the materials were found to be particularly adapted for the purposes of the petroleum industry. The cost of production was still further raised by the work that was imposed for national defense. The rise in costs per meter drilled was 50 per cent over those of 1939. According to bimonthly tables furnished by the Moniteur du Petrole Roumain, the deepest well completed in 1940 was an exploratory well, No. 201 of the Concordia company, drilled at Tintea and suspended at 3338 meters. This depth was reached toward the close of 1939 and the well was not deepened in 1940 became of large deviation from the vertical. The record for productive wells had been held by No. 429 at Tintea, drilled by Unirea to a depth of 3200 m., and in 1938 well No. 317 Cocorasti-Mislea, of the Colombia company, but these records were passed in 1940 by well No. 613 Liliesti of the Con-cordia company, which reached a depth of 3294 m. and had an initial production of 10 tons per day. In 1940, the same number of wells, II, had been drilled to a depth of over 3000 m. as in 1939. Five of these wells are at Tintea and six at Liliesti. Table I lists these very deep holes in the order of their depth. Table i.—Deep Wells Drilled in Rumania in 1940 Initial No. Produc- of Company Field Meters tion, Well Meters Tons per Day 405 Colombia......... Liliesti 3,001 10 629 Unireu............ Tintea 3,005 73 426 Unirea............ Tintea 3,050 48 410 Colombia. ........ Liljesti 3,055 30 627 Concordja (Unirea). Liliesti 3,072 75 430 627ConcordjaConcordia (Unirea). (Unjrea 3,II9 30 618 Colombia......... Liliesti 3,168 70 24 Steaua Romana. . . Tintea 3,184 18 412 24Unirea............ Tintea 3,211 23 613 Concordia......... Liliesti 3,294 10 Production in Rumania in 1940 reached 5,813,000 tons, in contrast to 6,~40,0oo tons in 1939, a decline of 427,000 tons, or 6.8 per cent. Drilling reached 241,500 m., in

Jan 1, 1941

By E. P. Sadowski, L. P. Trudeau, C. R. Cupp

The apparent high radiation resistance of two varieties of maraging steel is described and an indication is given of some phenomena that require further study. Two aspects were included in this work: a) effects of neutron irradiation on the room-ternperature tensile properties of 18 Ni (250) maraging steel; b) effects of neutron irradiation on the room-temperature tensile properties and on the impact resistance of 12 pct Ni-5pct Cr-3 pct Mo maraging steel. Subsize tensile and impact test specimens were used. The 18 pct Ni steel was irradiated to a neutron fluence of 3.3 x 10 n per sq cm (>1 mev). The 12-5-3 variety was irradiated to two neutron fluence levels: 1) 1.5 x 10 per sq CTTL (>I mev) 2) 3.1 x 10'9nper sq cm (>1 mev) In all respects both varieties showed unusually high resistance to change in strength and ductility after neutron irradiation. There was no noteuorthy over-aging in fully aged specimens. The aged 18 pct Ni variety showed a 4 pct drop in yield strength upon irradiation with little or no decrease in ductility. The aged 12-5-3 variety showed a 5 pct increase in yield strength on irradiation with a very slight decrease in ductility. The impact transition of the 12-5-3 variety only increased 35 to 45 Co upon irradiation, and the shear energy fracture value for the subsized specimens decreased only half as much as expected frorn experience with conventional steels. THE development of new reactor concepts and nuclear technology now depends to a large extent on the availability of new alloys capable of operating in stringent reactor environments. One of the most important new types of metallurgical material that has been developed in recent years is the maraging steels. This type of alloy is notable for its remarkable retention of toughness at high strength levels. In the course of a research program which incorporated ambient temperature radiation effects studies to determine the mechanisms of strengthening of 18 pct nickel maraging steel,' it became evident that the resistance of the alloy to neutron-induced changes in mechanical properties should be studied. This paper is to present evidence for the apparent high radiation resistance of maraging steel. The experimental program was in two parts: a) Effect of neutron irradiation on the room-temperature tensile properties of 18 Ni (250) maraging steel. b) Effect of neutron irradiation on the room-temperature tensile properties and on the impact resistance of 12 pct Ni-5 pct Cr-3 pct Mo maraging steel, a cobalt-free alloy. EXPERIMENTAL PROCEDURE 18 Ni (250) Maraging Steel. Tensile test specimens were machined to the dimensions shown in Fig. 1 from $-in.-diam hot-rolled bar of the composition shown in Table I. All specimens were austenitized for 1 hr at 1500°F (815°C) in argon and water-quenched. Half of the specimens were then mar aged for 3 hr at 900° F (482°C) in argon. The specimens were irradiated in a fast neutron transformer rod at approximately 120°F (50°C) to a neutron fluence of 3.3 x 10 10 n per sq cm (>1 mev). The irradiation was performed in the NRX reactor of Atomic Energy of Canada, Ltd., at Chalk River, Ontario, Canada. In all cases, the thermal neutron flux was three times as high as the reported (> 1 mev) fluxes. The room-temperature tensile tests were performed with an Instron tensile testing machine operating at a crosshead speed of 0.05 in. per min. The loading frame of the machine, mounted in a hot cell, was remotely controlled. The specimens were tested either

Jan 1, 1968

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined for the system gadolinium-nickel. Nine intermetallic compounds have been found at compositions corresponding to the following gadolinium-nickel ratios: 3:1, 3:2, 1:1, 1:2, 1:3, 2:7, 1:4, 1:5, 2:17. The GdNi and GdNi5 compounds have congruent melting points of 1300' and 1500°C, respectively while the remaining compounds melt in-congruently. Eutectics exist at 15 wt pct Ni, 31 1/2 wt pct Ni and 87 wt pct Ni with melting points of 6703 8803 and 1220°C, respectively. IN a continuing investigation of the properties of rare earth alloys, a study has been made of the gadolinium-nickel system. Previous work encompassed the iron containing alloys and a subsequent paper will deal with the constitution of the gadolinium-cobalt system. Vogel,1 examined alloys of nickel with lanthanum and cerium. R3Ni, RNi, RNi2, RNi3, RNi4, and RNi5 compounds were found. Endter and Klemm,2 Fulling et al.3 Heumann,4 and Nowotny5 found the 1:2 compositions of this series to exist in a C-15 (face-centered cubic) structure, and the 1:5 compositions in a hexagonal system. Jepson and Duwez6 more recently examined these 1:2 and 1:5 compositions and generally confirmed earlier data while Wernick and Geller7 most recently have given additional data on the GdNi5 compound. Comparisons with our results will be made in the appropriate section of this report. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been given in our earlier paper.8 Chemical analyses of the alloy samples were made by dissolving the specimen in nitric acid, precipitating the gadolinium as hydroxide and the nickel with dimethylglyoxime. Both precipitates were ignited to oxide and weighed. RESULTS Microstructure— Metallography of alloy specimens in this series has been conducted on both arc-melted and annealed materials. Etchants used have been 5 pct nital with approximately 10 pct distilled water added, for high gadolinium samples; Carapella's ferric chloride solution for intermediate compositions; and Marble's (copper sulfate) reagent for high nickel content alloys. Because of difficulties encountered in the grinding and polishing of specimens containing 40 to 75 wt pct Ni, no photomicrographs were made of such specimens. The microstructure of an arc-melted 5.3 wt pct Ni alloy is shown in Fig. 1. Light etching primary grains of gadolinium are embedded in an eutectic matrix. The microstructure of an alloy of 9.55 wt pct Ni alloy, Fig. 2, annealed 50 hr at 700°C, consists almost entirely of the intermetallic compound Gd3Ni. The structure of an arc metal alloy of approximately 19 pct Ni, Fig. 3, consists of grains of the compound GdNi embedded in the Gd3Ni2-Gd3Ni eutectic. The arc-cast structure of the 38.7 wt pct Ni alloy is shown in Fig. 4. Large primary grains of a compound rest in a matrix structure of coarse GdNi-GdNiz eutectic. Because of the occurrence of several peritectic compounds in the central region of the diagram, identification of the primary structure in this alloy is not certain. As has been indicated above, microstructures of alloy specimens containing between ca 40 and 75 wt pct Ni have not been photographed. These specimens were highly brittle, and macro- and micro-cracking were impossible to control in the grinding and polishing procedures. Prolonged annealing did not alleviate this condition. Visual observations in small specimens did, however, provide evidence for a multiplicity of phases and peritectic dissociations of compounds although rationalization of structures was not possible.

Jan 1, 1962

By J. Chipman, N. J. Grant, H. L. Bishop

In a recent review1 of the iron-oxide activity of simple open-hearth type slags containing lime, magnesia, silica, and iron oxide, it was established that activity values were lacking in the range of slag composition most interesting to open-hearth operators. That is, laboratory experimental results were not available for simple slag compositions having basicity ratios ranging from about 1.5 to 4.0 and iron-oxide concentrations ranging from about 10 to 30 pct. However, in order to estimate iron-oxide activities for the range of slag compositions of interest to open-hearth operators, activity values were calculated using ionic concepts of slags by following the treatment of Flood and Grjotheim.2 A study of these data indicated that the desired slag compositions were probably not obtained due to the limited solubility of the basic constituents lime and magnesia. Thus, it was decided to make additional heats equilibrating molten carbon-free iron with slags containing MnO, P2O5, and A12O3 in percentages commonly found in open-hearth refining slags, and to examine the liquid slag field over a greater composition range than that of the simple slags studied previously. The ranges of the constituents used in the present study are summarized as follows: Metal Pct 0 0.070-0.201 PctMn 0.005-0.142 Slag Pet CaO 24.45-41.90 Pct MgO 3.23- 9.21 Pct MnO 1.13- 9.62 Pct FeO 20.08-48.7 Pet Fe2o3 2.23-10.14 Pct SiO, 3.51-28.50 Pct P2O5 0.23- 3.65 Pct A12O3 0.43- 3.38 The experimental procedure consisted of equilibrating the slag and metal in an induction furnace provided with a carbon-arc slag heater as described previously by Winkler and chipman.3 The data obtained were used to establish both the iron-oxide activity values and the activity coefficients for FeO and MnO in the open-hearth type slags. RESULTS AND DISCUSSION I) Iron-Oxide Activity of Open-Hearth Type Slags—The iron-oxide activities of various iron-oxide contents of the open-hearth type slags, as calculated from the oxygen content of the metal by the method of Taylor and Chipman, 4 are plotted against the molar ratio of bases to acids in Fig. 1. The data represent slag-metal studies carried out in the temperature range 1530" to 1700°C. For the purpose of this study, the constituents CaO, MgO, and MnO are assumed equal on a molar basis in their effect on the iron-oxide activity; and, PO2,5 is calculated as an equivalent to SiO2 and A12O3 on a molar basis. The total iron content of the slag is calculated to FeO and is represented by the symbol (FeO) The points presented in Fig. 1 represent the results of this investigation for iron-oxide slags containing between 1 and 8 mol pct MnO and less than about 2 mol pct each of A12o3 and PO2,5 The curved lines shown in Fig. 1 represent the results of the summary1 of the iron-oxide activities of simple slags of the system (CaO + MgO) - SiOz - (FeO),. The solid portions of the curved lines represent experimental data, and the broken portions represent iron-oxide activities calculated from ionic concepts of slags. The iron-oxide values of the open-hearth type slags of this study are in good agreement with the values of the simple iron-oxide slag system. Only a slight modification is indicated. The results of this study suggest that the line for 20 mol pct (FeO), should be lowered slightly in the basicity range 1.5 to about 3.

Jan 1, 1959

By J. M. Boutwell

PAGE I. Introduction,.......541 II. General Geography,......542 III. General Geology,......544 1. Sedimentary Rocks,..... 544 2. Igneous Rocks,...... 545 3. Areal Geology,.......546 4. Structural Geology......547 IV. General Character of Ore-Deposits,...548 V. Genesis of the Disseminated Ore in Monzonite,.... 549 1. General,........549 2. Character and Occurrence,... 649 3. Genesis,....... 550 4. Superficial Alteration.....553 5. Conclusion......553 VI. Genesis of the Ore in Fissures,...553 1. Character........... 553 2 Occurrence......554 3. Deposition...... 556 4. Transporting Agent....555 6. Immediate Causes of Deposition..556 6. Superficial Alteration....564 7. Conclusionl ..... 565 VII. Genesis of the Copper-Ore in Limestone...... 566 1. Character......566 2. Occurrencel .....566 3. Deposition......567 4. Relation of Fissures.....569 5. Relation of Intrusives,...571 6. Superficial Alteration....575 7. Conclusion......578 VIII. Periods of Ore-Deposition....578 IX. Dates of Mineralization.....579 X. General Conclusions.....580 I. Introduction. The object of this paper is to present a concise statement on the genesis of the copper- and lead-deposits of the Bingham

Jan 1, 1906

By J. S. Marsh, T. B. Winkler

THE past year, the first full one of peacetime production, proved that the process of beating swords into plowshares has increased in complexity in step with civilization. Further, judging by various remarks of our distaff departments, the crystal balls of certain radio and magazine oracles must have been cloudy, because we have been in formed from time to time that coveted items such as automobiles and refrigerators did not appear in great abundance. This seemingly extraneous matter is really not out of place here, however; the steel producer and the fabricator exist in a sort of symbiosis: the making of consumer goods produces scrap which is returned to the steelmaker who makes more steel, and so on and so forth. Thus, no abundance of automobiles, no abundance of scrap from this normal source; and other sources had been picked pretty clean during the war. To be short, so was scrap. Since the economy of the steel industry lean; as heavily upon iron from scrap as upon iron from ore, the statement on transformation of swords to plowshares follows. But this is not the whole story: after all, ingot production was a record for a peace year!

Jan 1, 1947