Search Documents

By C. D. Rubert, W. J. Parton

LARGE quantities of fine anthracite with associated impurities are discharged with the waste water from the coal-cleaning plants in the Pennsylvania anthracite region. Furthermore, for many years this fine material has accumulated and formed silt banks. The difficulty of removing the impurities from the fine material and the lack of adequate markets are responsible for the waste of this material. In view of a larger demand for fine coal, mainly for pulverized fuel, the Lehigh Navigation Coal Co. Inc. decided to investigate the froth flotation process for recovery of fine coal from these waste solids. A test plant was constructed and operated for six months during 1942 in order to determine the practicability of recovering coal from the waste water of a cleaning plant (breaker) by froth flotation, and to obtain operating data for designing a commercial plant if the results were favorable. PRELIMINARY INVESTIGATION Before the pilot plant was constructed information was obtained by field and small-scale laboratory tests to serve as a guide in the design and operation of the pilot plant. Size and ash analyses of a representative sample of the material discharged in the wash water from a cleaning plant are given in Table I. [ ] The refuse content increases progressively as the size of the particles decreases. The larger particles (+35 m.) are low in ash content and could be marketed without cleaning. Since these solids are discharged from the breakers with 90 to 95 per cent water by weight, the first step in the recovery of the coal was that of reducing the quantity of water so that water in excess will not have to be handled. Furthermore, it was found that the removal of most of the minus 200 mesh high-ash material was desirable to permit the most efficient flotation of the coal. Classification tests were run and showed that a hydroseparator overflow rate of 12 ft. per hour was sufficient to eliminate much of the minus 200-mesh material while allowing the coarser material to settle and be thickened.

Jan 1, 1944

By H. A. J. Wilkens, H. B. C. Nitze

At the Atlanta meeting of the Institute in October,' 1895, some brief remarks were made by Mr. Wilkens on the above subject. It is the object of this paper to set forth the substance of these previous statements, embodying therewith additional information gained since that time, and a brief illustrated description of the method and means of the separation.* Lack of time will unfortunately not allow as complete a resume of the subject in all its phases, especially those relating to the scientific side of the question, as its novelty and importance would warrant, so that even this paper must be considered a preliminary one. It is hoped that at some future meeting of the Institute we may find an opportunity of presenting supplementary data of interest. The paradoxical title above used requires some explanation. The term " non-magnetic material " is applied to such substances as have heretofore been considered non-magnetic in the arts, more especially in the practice of ore-concentration. Scientifically, it has been shown by Faraday, Plucker, Wiedemann and other physicists that magnetism is an inherent property common to all substances, solid, liquid and gaseous, i.e., all suhstances are either attracted or repelled by the poles of a magnet, although ill the great majority of cases the manifestation of this

Jan 1, 1897

By Roy McLellan

THE slags derived from the smelting of lead and copper ores are composed essentially of silicates. The problems arising from the smelting of these ores consequently involve the study of silicate fusions. In the absence of specific knowledge concerning the compounds occurring in slags, it has been the practice of metallurgists to treat them in terms of their total chemical composition. Slags have been classified as monosilicates, bisilicates, sesquisilicates, and subsilicates according to the relative amounts of oxygen in the acid and basic radicles of the hypothetical salt produced. While this has been a useful guide to metallurgists in computing the furnace charges, it falls far short of a basis for the scientific investigation of slags. In order to understand the nature of a slag as a whole it is necessary to learn the physical and chemical properties of the mineral compounds which go to make up that slag. The efficiency with which an ore is smelted in a furnace depends primarily on the physical properties of the compounds formed during the operation. When the melting points and fields of stability of each of the mineral compounds in slags have been established, it will be possible to determine the properties of any given slag by examining the nature and amounts of its mineral constituents.

Jan 1, 1930

By Frederick N. Rhines

Pure copper that has been allowed to oxidize at an elevated temperature in the air is found to be covered with two distinguishable layers of oxide scale. The outer of these, which is very thin, is composed of cuprie oxide, while the inner layer, comprising the bulk of the scale, is made up chiefly of cuprous oxide (Fig, la). If a small quantity of an alloying element, such as silicon, is present in the copper, silica particles are found disseminated through the cuprous oxide, deposited most abundantly near the metal surface, and, in addition, silica particles occur to a limited depth within the copper itself (Fig. 1b). It is this inner layer, composetl of oxide particles precipitated in a matrix of metallic copper, that is known as the "subscale" or the zone of internal oxidation. Under a low oxygen pressure it is possible to produce the subscale without the formation of external layers of copper oxides, thus leaving the metal surface bright and apparently clean while oxidation has occurred, in fact, to a considerable depth within the metal (Fig. 2). Although little is yet known in a detailed way of the mechanism of internal oxidation, the general nature of the process is evident. By virtue of the considerable solubility of oxygen in copper,' it is possible to bring the alloying element in contact with oxygen within the metallic solid solution. If the oxide of the alloying element is more stable than cuprous oxide, the foreign oxide may form and, since most oxides are relatively insoluble in copper, it will not long remain in solution, but mill separate as a precipitate. As the metallic solute is exhausted in the zone of precipitation, oxygen that is constantly being supplied at the surface diffuses farther into the alloy and thus produces an ever-thickening shell of subscale. The distribution of the reacting elements in the subscale and adjoining zones must be somewhat as indicated in Fig. 3. The conditions requisite to internal oxidation to be anticipated are thus: (I) a solubility of oxygen in the alloy, (2) the ability of oxygen to diffuse at an appreciable rate into the alloy, (3) the possibility of the

Jan 1, 1940

By Frederick N. Rhines

Pure copper that has been allowed to oxidize at an elevated temperature in the air is found to be covered with two distinguishable layers of oxide scale. The outer of these, which is very thin, is composed of cuprie oxide, while the inner layer, comprising the bulk of the scale, is made up chiefly of cuprous oxide (Fig, la). If a small quantity of an alloying element, such as silicon, is present in the copper, silica particles are found disseminated through the cuprous oxide, deposited most abundantly near the metal surface, and, in addition, silica particles occur to a limited depth within the copper itself (Fig. 1b). It is this inner layer, composetl of oxide particles precipitated in a matrix of metallic copper, that is known as the "subscale" or the zone of internal oxidation. Under a low oxygen pressure it is possible to produce the subscale without the formation of external layers of copper oxides, thus leaving the metal surface bright and apparently clean while oxidation has occurred, in fact, to a considerable depth within the metal (Fig. 2). Although little is yet known in a detailed way of the mechanism of internal oxidation, the general nature of the process is evident. By virtue of the considerable solubility of oxygen in copper,' it is possible to bring the alloying element in contact with oxygen within the metallic solid solution. If the oxide of the alloying element is more stable than cuprous oxide, the foreign oxide may form and, since most oxides are relatively insoluble in copper, it will not long remain in solution, but mill separate as a precipitate. As the metallic solute is exhausted in the zone of precipitation, oxygen that is constantly being supplied at the surface diffuses farther into the alloy and thus produces an ever-thickening shell of subscale. The distribution of the reacting elements in the subscale and adjoining zones must be somewhat as indicated in Fig. 3. The conditions requisite to internal oxidation to be anticipated are thus: (I) a solubility of oxygen in the alloy, (2) the ability of oxygen to diffuse at an appreciable rate into the alloy, (3) the possibility of the

Jan 1, 1940

By E. W. Filer, L. S. Darker

ONE of the primary purposes of this investigation was to determine how far blast-furnace metal and slag depart from equilibrium, particularly with respect to sulphur distribution. In studying the equilibrium between blast-furnace metal and slag, there are two approaches that can be used. One method is to use synthetic slags, as was done by Hatch and Chipman;' the other is to equilibrate the metal and slag from the blast furnace by remelting in the laboratory. In the set of experiments here reported, metal and slag tapped simultaneously from the same blast furnace were used for all the runs. The experiments were divided into two groups: 1—a time series at each of three different temperatures to determine the t.ime required for metal and slag to equilibrate in various respects under the experimental conditions of remelting, and 2—an addition series to determine the effect of additions to the slag on the equilibrium between the metal and slag. An atmosphere of carbon monoxide was used to simulate blastfurnace conditions. The furnace used for this investigation was a vertically mounted tubular Globar type with two concentric porcelain tubes inside the heating element. The control couple was located between the two porcelain tubes. The carbon monoxide atmosphere was introduced through a mercury seal at the bottom of the inner tube. On top, a glass head (with ground joint) provided access for samples and a long outlet tube prevented air from sucking back into the furnace. The charge used was iron 6 g, slag 5 g for the time series, or iron 9 g, slag 7 % g for the addition series. This slag-to-metal ratio of 0.83 approximates the average for blast-furnace practice, which commonly ranges from about 0.6 to 1.1. A crucible of AUC graphite containing the above charge was suspended by a molybdenum wire in the head and, after flush, was lowered to the center of the furnace as shown in Fig. 1. The cylindrical crucible was 2 in. long x % in. OD. The furnace was held within &3"C of the desired temperature for all the runs. The temperature was checked after the end of each run by flushing the inner tube with air and placing a platinum-platinum-10 pct rhodium thermocouple in the position previously occupied by the crucible; the temperature of the majority of the runs was much closer than the deviation specified above. The couple was checked against a standard couple which had been calibrated at the gold and palladium points, and against a Bureau of Standards couple. The carbon monoxide atmosphere was prepared by passing COz over granular graphite at about 1200°C. It was purified by bubbling through a 30 pct aqueous solution of potassium hydroxide and passing through ascarite and phosphorus pentoxide. The train and connections were all glass except for a few butt joints where rubber tubing was used for flexibility. The rate of gas flow was 25 to 40 cc per min. As atmospheric pressure prevailed in the furnace, the pressure of carbon monoxide was only slightly higher than the partial pressure thereof in the bosh and hearth zones of a blast furnace—by virtue of the elevated total pressure therein. Simultaneous samples of blast-furnace metal and slag were taken for these remelting experiments. The composition of each is given in the first line of Table I. There is considerable uncertainty as to the significant temperature in a blast furnace at which to compare experimental results. This uncertainty arises not only from lack of temperature measurements in the furnace, but also from lack of knowledge of the zone where the slag-metal reactions occur. (Do they occur principally at the slag-metal interface in the crucible, or as the metal is descending through the slag, or even higher as slag and metal are splashing over the coke?) The known temperatures are those of the metal at cast, which averages about 2600°F, and of the cast or flush slag, which is usually about 100°F hotter. To bridge this uncertainty, remelting temperatures were chosen as 1400°, 1500" (2732°F), and 1600°C. For the time series the duration of remelt was 1, 2, 4, 8, 17, or 66 hr; crucible and contents were quenched in brine. The addition series were quenched by rapidly transferring the crucible and contents from the furnace to a close-fitting copper "mold." Of incidental interest here is the fact that the slag wet the crucible

Jan 1, 1953

By E. H. Dix

During an investigation of high-strength manganese bronze by til Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received thc carly co~l+itlcl-ntio11 of scirntific rcsc:trch. Thc diagram, according to the rnost rcrent \vork.' IS shown in Fig. 1. The disputed questions involve the tcrmi~r:~tiorl of the beta field and the lint at 470' C. The parliest expc~imc>ntcr, Rol)erts--~1~11stcri, detectrd an arrest in some of his cooling curves :it approximately this temperature and ascribed them to the formation of a cutectic; it has since been proved that there arc no eutectics in this series. Shepherd? was unable to detect any thermal arrests at this temperature, his. diagram was essentially as shown in Fig. 1, except that the line at 470" ('. was omitted and the beta phase carried down to normal temperature. 1,:ttcr. carpenter and Edwards, by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the BETA constituent into a cutectoid of alpha and gamma. microscopic evidence of the formation of the cutectoid is doubtful and it seems more likely to he due to an allo-tropic change in the beta constituent as shown by Fig. 1. At least for practical purpose?, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather thin alpha plus an unresoluble eutectoid of "apparent beta" as it has often been called. * Chief, Metals branch, Engineering Division, Air Service. 1 0. F. Hudson: Jnl. Inst. of hlvtals (1913) 12, 2 E. S. Shepherd: Jnl. Phys Chrm. (10141 8, 421. H. C. H. Carpenter and O. A. Edwards: Jnl, Inst. of Metals (1911) 5, 127.

Jan 1, 1923

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By William B. Senseman

For reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system, and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of mill power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1947

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By J. S. Woodward, F. B. Plummer

The measurement of the rate of flow of liquids through sands dates back to 1856, when H. d Arcyb, a French physicist, carried out his classic experiments on the flow of water through sand layers. The earliest recorded data on relationships of pressure to flow of fluids through porous rocks in this country are those of Newell 23 in 1885. The first comprehensive studies of flow were made in 1898 by King15, who measured the rate of flow of water and air through consolidated and uncon-solidated sands and published the results. From 1900 to 1920 there appears to have been little interest in permeability. In 1920 the increase in demand for oil led the U. S. Bureau of Mines to begin a series of experiments to determine subsurface relationships of oil and water and the characteristics of their flow. Mills18 studied the relationship of flow of liquids to text- and structure of the sands, and Melcher17 in 1925 made a quantitative study of effect of changes in pressure on rate of flow of crude oil through Oklahoma oil sands. Since 1930 the importance of flow measurements to production of oil and gas has been emphasized by a large number of excellent investigations. Among these the works of Fettke9.10, BarbI.2, Cloud6, Nutting24-", Bot-set4, Nevin22, Tickell32.33, Fancher, Lewis and Barnes8, Moore, Schilthuis and Hurst19, and Wyckoff, Botset and Muskat"-39 have contributed much to our knowledge of the technique of permeability measurements and to the laws of liquid and gas flow through porous sands. The application of their work has led to the establishment of laboratories for measuring the permeability and porosity of oil sands by most of the large companies. All the investigations, except those of Wyckoff, Botset and Muskat, and Moore, Schilthuis and Hurst deal with linear flow; that is, flow in a more or less straight line through a given cross-sectional area of sand. Three years ago, at the University of Texas, experiments were started to measure radial flow of liquids through sands; that is, flow from all directions toward a central opening—the conditions that operate in a

Jan 1, 1937

By E. H. Dix

During an investigation of high-strength manganese bronze by til Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received thc carly co~l+itlcl-ntio11 of scirntific rcsc:trch. Thc diagram, according to the rnost rcrent \vork.' IS shown in Fig. 1. The disputed questions involve the tcrmi~r:~tiorl of the beta field and the lint at 470' C. The parliest expc~imc>ntcr, Rol)erts--~1~11stcri, detectrd an arrest in some of his cooling curves :it approximately this temperature and ascribed them to the formation of a cutectic; it has since been proved that there arc no eutectics in this series. Shepherd? was unable to detect any thermal arrests at this temperature, his. diagram was essentially as shown in Fig. 1, except that the line at 470" ('. was omitted and the beta phase carried down to normal temperature. 1,:ttcr. carpenter and Edwards, by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the BETA constituent into a cutectoid of alpha and gamma. microscopic evidence of the formation of the cutectoid is doubtful and it seems more likely to he due to an allo-tropic change in the beta constituent as shown by Fig. 1. At least for practical purpose?, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather thin alpha plus an unresoluble eutectoid of "apparent beta" as it has often been called. * Chief, Metals branch, Engineering Division, Air Service. 1 0. F. Hudson: Jnl. Inst. of hlvtals (1913) 12, 2 E. S. Shepherd: Jnl. Phys Chrm. (10141 8, 421. H. C. H. Carpenter and O. A. Edwards: Jnl, Inst. of Metals (1911) 5, 127.

Jan 1, 1923

By James W. Shaffer

Aluminum is the most abundant metallic element of the earth's crust and is a constituent of nearly every type of rock (Clark, 1924, p. 13). The sources of aluminum and aluminous material most commonly used by modern industry are the bauxitic raw materials consisting of bauxite, bauxitic clay, and aluminous laterites. These are mixtures of hydrated aluminum oxide minerals and mineral impurities. End Uses Bauxite is used as an aluminum ore and in the manufacture of refractory products, aluminous chemicals, and abrasives. Other raw materials are used for aluminum ores, but their use is minor compared to bauxite. Refractory products made from bauxite are synthetic mullite, high-alumina fire bricks, castables, monoliths, cements, and ramming mixes used by the iron, steel, and cement industries. Chemicals made from bauxite are aluminum sulfate and sodium aluminate for water treatment and aluminum chloride used in refining crude petroleum. Among the abrasive products made from bauxite are coated abrasives, sharpening stones, and grinding wheels. Special grades of bauxite are used in the decolorization and clarification of raw sugar and lubricating oils. Bauxite has been used for road surfacing but mainly because other material was not more readily available. Perhaps the oldest use of bauxite and aluminous laterite is for a building stone. Ancient temples and more recent structures in India have been made from these and some varieties are suitable for decorative stone. Geology Mineralogy and Properties – Bauxite is a mineral raw material composed principally of one or more hydrated aluminum oxide minerals and impurities of silica, iron oxide, titania and elements in minor or trace amounts. The hydrated aluminum oxide minerals are gibbsite, boehmite and diaspore. Corundum is not included as a bauxite mineral although it does occur in some bauxite deposits. Boehmite and diaspore are both alumina mono-hydrates and have essentially the same composition, but diaspore has a greater hardness and a higher specific gravity because of a more tightly bonded and compacted atomic structure. Gibbsite is an alumina trihydrate mineral. Properties of bauxite minerals are shown in [Table 1].

Jan 1, 1975

By K. B. Nowels

The attainment of efficient flooding to a large extent depends upon a knowledge of fluid movement through porous media and the pressures used in controlling this movement. Little has been understood con-cerning the fundamental principles involved in the forced drive of water-flooding and an attempt will be made to present some data which may be of interest. Considerable data and technical information pertaining to natural and artificial water-flooding have been presented in the past by Torrey, Umpleby, Fettke, Panyity and others. Their papers have thoroughly covered the description of past and present-day methods of oil recovery by flooding in the Bradford field, especially an article by Torreyl in the Petroleum Engineering Handbook. A bibliography of papers devoted to watcr-flooding, published in Mr. Torrey's article, is appended to this paper. No attempt has been made, therefore, to describe the installations and procedure necessary in flooding, thus permitting the writer to deal exclusively with the mechanics of water movement in flooding operations and its relationship to well spacing. Artificial water-flooding will probably always be the most successful in oil fields described by Herold as being under "capillary control"" and will probably be useless in fields naturally under hydraulic or volumetric control. The natural water drive in an oil field under either of these two controls may give efficient recoveries, as a result of the regulated encroachment of edge water. Such a "natural flood" resulting from the influence of edge water must not be confused with the term as used in this paper, however. Any reference to "natural flood" will here refer to the old method of flooding formerly used in the Bradford field. This was discovered largely by accident and utilized the hydrostatic pressure created by a column of water standing in a watered-out oil well in forcing the oil to an adjacent producing well. The same principles are involved in either natural or artificial flooding, and the latter method simply

Jan 1, 1933

By William B. Senseman

For reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system, and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of mill power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1947

By T. H. Aldrich

The Aldrich Mining Go. holds under lease from the Illinois Central R. R. Co. about 14,000 acres, in the east half of Township 12, Range 12 W., in Marion county, Alabama, and owns other lands, of which about 1,000 acres adjoin this leased tract, making a total area of about 15,000 acres, all of which is underlain by the coal-seam upon which the company is operating. This seam is nearly horizontal; and a ravine, diagonally crossing the tract, exposes the outcrop on either side for about 2 miles. The territory has been so divided that nearly the whole of it can be worked out by two collieries. The mines at Brilliant were opened in the fall of 1898, and shipments began in the following spring. The original plan was to furnish steam-coal for locomotives to the Illinois Central R. R. Co.; and upon this expectation the investment of capital was made. The field was entirely new; and the softness of the coal at the outcrop induced the belief that it could be very cheaply mined. A contract for the delivery of a large quantity of coal to the railroad was accordingly executed. But with the advance of' the entries to increasing distances from the outcrop, the coal proved so hard that it could no longer be drilled with a breast-auger; and the expense of mining became so great that the contract for cheap steam-coal had to be canceled. It became evident that the work must be done with machinery and explosives, if it could be profitably done at all. On the other hand, the excellent quality of this coal opened, at the same time, a possible market not specially contemplated at the outset—namely, that of a first-rate coal for domestic and general uses. Since no other deposit of such coal was known to exist on the line of the Illinois Central, or any other railroad

Jan 1, 1907

By S. W. Zanolli

The history of labor relations in the coal industry of the United States is a study of its collective bargaining. This study of collective bargaining is largely the history of the United Mine Workers of America and its contractual relations with the various coal mining employers who have produced this country's coal over the years under a free enterprise system. There have been other unions in the picture from time to time and some coal miners have mined coal without representation by any union. Even today some 25% of the nation's coal is produced outside of the collective bargaining relationship with the UMWA. However, more than 100,000 coal mine wage employees - well over 75% of the total in the industry - are covered by labor agreements negotiated for them by the UMWA. Practically all of these work in bituminous mines.

Jan 12, 1972

By J. T. Burwell, J. Wulff

As is well known, the alloys of iron containing 18 ± per cent chromium, 8* per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composition (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff,1 it was decided to investigate the phenomenon by electron diffraction methods. Apparatus The apparatus used (Fig. 1) was a hot-filament type employing movable slits, similar to that described by Germer.2 The sample-to-photographic plate distance was 69 cm. and the accelerating voltage 30 kv. Since electrons do not in general follow geometrical paths, it is necessary that either the electron source or the sample be movable in a plane normal to the beam. In this case the sample is fixed and the electron source is movable. The source is adjusted until the shadow of the sample appears in the brightest part of the beam as viewed on the fluorescent screen, then the slits composing the two pinholes are inoved into position one by one. The system is evacuated by means of a mercury diffusion pump backed up with a Cenco Hypervac oil pump. Pressures lower than 10- mm. of Hg are read on a calibrated ionization gauge.

Jan 1, 1939

By Casimir Constable

DURING the years 1875 to 1879 I had charge of the Rockwood furnaces and mines, situated forty miles from the nearest railway communication at that time, and one hundred miles north of Chap tanooga, Tenn., by the Tennessee River. The small furnace with old-fashioned stoves, then in blast, was built under great difficulties by General Wilder. The early conditions were somewhat as follows: The ore was fossil ore of the Clinton group ; very fine and generally wet, without other admixture. The coke had a large amount of ash, and the fur" nace appeared to be badly scaffolded at times. On many days only a few tons of iron could be obtained. The founder generally id creased the revolutions of the engine when signs of chilling appeared,. The cinder at such times was black, very scoriatious, often closely resembling mill cinder. When the pressure was increased (the joints being the old-fashioned rust joints), leaks in the blast-pipe occurred It was noted that when the blast was stopped, and the leak bolt imperfectly remedied, the furnace improved a little. This set me thinking on the right track; and I took the responsibility of be coming my own founder for a time. A scaffolded condition had existed, and the situation was a trying one. Strange to say the negroes proved excellent furnace-men. Conceiving the hearth of the furnace to be similar to the grate area of a steam-boiler, capable of disposing of but so much fuel per hour, and requiring only a corresponding amount of air, it follows that an excess of air will burn the fuel not yet arrived at the hearth!, and raise the melting-point far above the tuyeres. This might pro duce scaffolding or at any rate choke the boshes, and leave less fuel to be consumed in the hearth. Thus for the time being less ail;. would be needed, as the continued burning of fuel in and above the boshes, would only aggravate the trouble. This condition of affairs accounted for the black cinder; the heat above having melted ore not yet perfectly reduced. This view decided me to reduce the revolutions of the engine; thefurnace finally became gray, as might have been expected. Any attempt to increase the speed produced black cinder and hard iron ;

Jan 1, 1883

By B. F. Koch

COPPER reverberatories develop large amounts of exit gases of a temperature in the neighborhood of 2000°F. The gases are not only of a noxious nature but must usually be disposed of at considerable heights above the yard level by a stack. Handling these gases at the temperature mentioned would require rather expensive construction of conveying flues and stack. Moreover, wasting such amounts of heat is certainly most uneconomical. Numerous investigations have indicated that waste heat boilers of the water-tube type are the most practical and economical means for utilizing that heat although the gases are heavily laden with rock dust and copper-bearing slag, which upon cooling form hard deposits on the surfaces of dampers or heat absorbing elements placed in the gas stream. Avoiding Slag and Dust Deposits Based largely on the experience of the paper industry in burning black liquor, a waste heat boiler design was developed a few years ago, providing not only extensive water-wall surfaces for cooling the gases below the fusing point of the slag but also settling out, as far as possible, the solidified particles of slag by creating low gas velocity. Matter carried in a stream of gases or air has a tendency to maintain its original direction upon a change in the direction of the flow of the conveying medium. Reverberatory waste heat boilers installed at Hurley and Morenci endeavored to utilize that tendency for the elimination of slagging particles at predetermined places and before they would strike the tube banks of the boilers. Both installations were successful in minimizing the slagging of boiler tubes and thereby minimizing the need for hand lancing. However, the low draft carried at the up-take of the reverberatory furnaces resulted in a positive pressure in the upper part of the furnace of the waste heat boilers, causing the emission of gases from lancing doors and making more difficult the already unwelcome work of cleaning the boilers by handlancing. Attempting to correct this nuisance as much as possible, the overall height of the Chuquicamata waste heat boilers has been reduced to the minimum considered necessary to obtain proper water circulation in furnace walls. Moreover, it is attempted to solidify slag and dust particles by providing large amounts of water-cooled surfaces before the gas stream reaches super-heater and convection banks of the boilers. The furnaces have been made as deep as an economical and practical arrangement of headers for water

Jan 1, 1952