Search Documents

By H. M. Crankshaw

The early methods of mining anthracite in the steep pitching Mammoth bed consisted in driving breasts up the pitch from the gangways and airways driven in the bed along the strike (Plate 2, Fig. 1). Breasts are simply rooms driven up the pitch the full thickness of the bed (Plate 2, Fig. 2), having a width of from 18 to 30 ft., and a manway or traveling way on one or both sides. (For detail of breast method see Whildin, Trans., vol. 50, p. 704). Many difficulties were encountered, and the maintenance cost of the timbered gangways was so great as to be practically prohibitive. To reduce this expense, the gangways were driven in the thin Skidmore bed underlying the Mammoth, and the coal mined through rock holes. (Plate 2, Fig. 2, A.) It was found that after the breasts were driven up 80 to 100 ft., the coal almost invariably rushed or "ran away," making good ventilation almost impossible and the extraction of coal from the upper portion of the lift very difficult. The economic length of a lift is from 200 to 250 ft., and the percentage of extraction by the old method above mentioned was often under 50 per cent., while the coal recovered was so badly broken up as to reduce materially the percentage of large sizes. Principles of Present Mining Methods The present methods designed for the recovery of a maximum percentage of coal and a maximum yield of the prepared sizes depends largely on the following principles: First.—Formerly the practice in mining bituminous coal was to space rooms so that as much coal as possible could be extracted in first mining (Plate 3). The small pillars were often lost, and an improvement in total extraction was found in the system of driving narrow rooms with wide pillars, with a much larger final recovery (Plate 4). Second.—The early method of ventilation was to maintain a single

Jan 1, 1917

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix .2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smiths have pointed out, that the lamellae delineate the [210] planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By Wheeler P. Davey, Robert T. Phelps

A study of solid solutions has long been a source of interest because of the conditions controlling their formation. X-ray investigations so far have been conducted with the idea that there were two types of solid solutions. In the first type, an atom of the solute was supposed to replace an atom of the solvent in the crystal lattice. In the second type, an atom of the solute was supposed to lie in one of the interstices between the atoms of the solvent. These pictures both require that the sizes of the atoms must play an important part in the process of solution. It is the purpose of the present investigation to study the mechanism of solid solution, using pure silver as the solvent, and pure aluminum as the solute. X-ray measurements show that these elements have the same "shape" of atomic domains1 (they both crystallize as face-centered cubes) and that their atomic diameters differ by less than one per cent.' The results of the present investigation point toward a chemical rather than a physical picture of the nature of solid solution, and make the older pictures merely special cases of a more general picture. The new theory has the advantage, too, that it offers a rational explanation of certain phenomena which hitherto have been only interesting detached facts. The aluminum-silver system which was chosen for this study has been studied by various methods by several workers. By means of thermal analysis Gautier2 and Petrenko3 have determined the phase diagram. Hansen studied the aluminum-rich alloys by means of thermal and microscopic analyses. He showed that at high temperatures silver dissolved in aluminum to the extent of 47 per cent by weight at 560" C. But this solubility decreased to 1 per cent at 200" C. Westgren and Bradley5 made an extensive X-ray study of these alloys. They used the change in the lattice parameter of silver as a criterion of the solution State College, Pa.

Jan 1, 1932

Alfred Stansfield, Montreal, Canada:—In Professor Howe's paper on the position of Ae3, he shows its industrial importance in determining the temperature to which steel should be heated for " grain refining." Several years ago I carried out a research on the " burning " of steel and found that while hypo-eutectoid steel should be heated to Ae3, hyper-eutectoid steel that has been very much overheated must be reheated to the curve Sa on the carbon-iron diagram, in order to redissolve the pro-eutectoid cementite and thus to obtain recrystallization and grain-refining. This treatment was necessarily only partly successful, and I should like to ask whether the conditions of heat treatment for refining overheated high-carbon steels have been ascertained. Speaking of the &'Persistence of Solidificational Segregation " Professor Howe quotes an experiment made by Mr. Stead in which a bar of 1.2 per cent. carbon steel was immersed in a large mass of molten blast-furnace slag and allowed to cool with it. The steel was heated ; above the solidus (curve An on the carbon-iron diagram), but below the liquidus (curve AB). A drop of eutectic carbon-iron alloy, rich in carbon, had liquated out and hung below the bar. This agrees exactly with my own observations on the burning of steel, but my interpretation differs somewhat from that of Professor Howe. Professor Howe considers that the fusion of a part of the metal (rich in carbon) shows that the solidificational irregularities of composition had persisted through the rolling and heat treatment of the steel, as otherwise no part of the steel would have been sufficiently fusible to melt. It does not appear to me that such an explanation is necessary. A piece of steel represented in temperature and composition by any point within the area ABa will ultimately resolve itself into a solid phase and a liquid phase in equilibrium with each other. It may appear that if the steel were absolutely uniform no fusion could take place, but, the smallest nucleus of high-carbon, fusible alloy would ultimately bring about this separation into liquid and solid phases, by diffusion of the carbon from the solid to the liquid areas. A nucleus sufficient for the purpose might be provided by an area of pro-eutectoid cementite which had not become diffused during the

Jan 1, 1914

By J. B. Mudd

Introduction It is difficult to think of any activity on which mankind has been more dependent than mining, and certainly there is much evidence in almost every part of the world of old workings that clearly demonstrate that man from earliest times has dug and toiled to take from the earth precious stones, metals and materials that from time to time have been essential or of value to him. In step with social development and industrial and technological advances the tempo of mining activity, regulated only by the laws of supply and demand, has quickened and in this century has accelerated rapidly in keeping with its dramatic development. Indeed, the rate of change of events has been such that if it were to continue to accelerate as fast as it has over the past decade there is reason to wonder how the insatiable demands for metals and minerals are to be met in the years that lie ahead. Shallow mines containing high-grade ore deposits either have been or are being rapidly mined out and their place can only be taken in general by ore lying at greater depth, or by ore of low grade, situated for the most part in remote and in underdeveloped areas. The cost of exploration and development is rising at an alarming rate, with the result that the expenditure now required to bring a mine to production far exceeds anything previously contemplated. It is estimated that the total capital required to maintain existing operations and develop new ones during the next 5 years will be of the order of $50,000 million and of this, new capital to bring new mines to production will be of the order of $3,000 million. Today no single mining finance company can, from its own resources, find all the money for a major mining development, and as a consequence there has been a strong trend toward joint ventures and to the formation of multinational consortiums. International lending institutions already play an important part in financing many new mining projects and their participation provides the financial umbrella under which other lenders can invest with greater security. There is little doubt that to finance the costly ventures in the future, governments and international lending agencies, banks and finance

Jan 1, 1971

By R. E. Cech, J. H. Hollomon

KURDJUMOV and Maksimova reported experiments with manganese steels and high carbon steels' and with an Fe-Ni-Mn alloy' in which mar-tensite was formed isothermally over a range of temperatures. They found in some cases that mar-tensite formation could be suppressed by rapid quenching to liquid nitrogen temperature. From their microstructural observations of martensite formed isothermally, they concluded that the rate controlling step is nucleation rather than growth. Kulin and Cohen,3 in an attempt to reproduce these experiments, found that with a steel having the same composition as that reported by Kurd-jumov and Maksimova, the transformation to martensite was essentially complete above the temperature range of Kurdjumov and Maksimova's isotherms. The possible reasons for this disagreement were not considered. Recent papers by Das Gupta and Lement4 and Kulin and Speich5 report the formation of isothermal martensite in a high chromium steel and in an Fe-Cr-Ni alloy, but neither paper can be considered a verification of the original Kurdjumov and Maksimova results. Further, in neither case were the authors able to suppress the formation of martensite entirely. Because of the important bearing the Kurdjumov and Maksimova results have to an understanding of the mechanism of martensite reactions it was felt that an experimental investigation directly concerned with checking the validity of their results was in order. This paper describes the results obtained on the isothermal transformation over the temperature range from —79" to —196°C of an alloy of iron, nickel, and manganese. Experimental Apparatus A 15 lb heat of an alloy containing 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn was melted by induction and cast under argon. The ingot was forged to 1-in. bar and a portion rolled to 1/16x1 1/2-in. strip. This strip was pack-homogenized 300 hr at 1100" in a helium-filled sealed iron tube. The composition after homogenization was 73.2 pct Fe, 22.94 pct Ni, 3.73 pct Mn, 0.05 pct C, and 0.015 pct N. The strips were cut to 1/2-in. width for dilatometer and metal-lographic specimens. Only the center portion of the 11/2-in. strip was used in the present investigation. The dilatometer employed was similar in design to one described by Flinn, Cook, and Fellows." A concentric fused auartz rod and tube assembly with hooks for holding the specimen was mounted so as to transmit the specimen dilation to a 1/10,000 in., 1/10 in. travel dial gage. The dilatometer proper was mounted by means of extension arms to a counterweighted sliding member on a vertical standard. This method of mounting permitted rapid transfer of the dilatometer from the austenitizing furnace to the quenching bath and low temperature chamber. A small electrical vibrator on the dilatometer kept frictional effects of the quartz members at a minimum. The austenitizing unit was a vertical, molybdenum-wound, hydrogen atmosphere furnace maintained at a constant temperature ±3°C by means of constant power input. A 12-in. stainless steel jacketed copper liner having 1/2-in wall thickness acted to equalize the temperature in the hot zone of the furnace. This liner, closed at the bottom end and open at the top to permit entrance of the dilatometer and specimen, was kept filled with dry nitrogen gas. A chromel-alumel thermocouple was placed inside the tube to determine the temperature. The 4-in. dilatometer specimens in the chamber varied less than 1/2° across the specimen length except for a 1 1/20 drop at the end nearest the open end of the furnace. The low temperature isothermal holding bath was a double Dewar arrangement similar to one described by Turnbull7. The outer bath was filled with a refrigerant at a temperature lower than the desired holding temperature. The inner bath was filled with Freon "11" or "12" or a mixture of both, depending upon the holding temperature. This inner bath which tended to be cooled by the outer bath was kept at a constant temperature by introducing a small amount of heat with a manually controlled electric heater. Stirring was accomplished by bubbling dry air through the bath. A Leeds and North-rup type K potentiometer was used to measure the inner bath temperature as indicated by a five element copper-constantan thermopile. The bath temperature was maintained within ±0.2°C of the desired temperature by occasionally adjusting the heater current so as to keep the Leeds and Northrup galvanometer at zero deflection with a constant setting of the potentiometer. Isothermal tests were usually continued for 300 to 400 min and another reading made at approximately 1000 min if the bath, unattended overnight, had not deviated in temperature more than 5°C. Transformation curves are drawn dashed (Fig. 1) through the time region where temperature was not controlled precisely. Experimental Procedure Dilatometer specimens of 1/2x1/16-in. strip were cut to 41/2-in. length and holes were drilled for the quartz hooks with proper spacing to give a 4-in. measured length. A thermocouple consisting of 0.012-in. diameter chrome1 and alumel wires was spot welded to the specimen and threaded between the dilatometer rods to binding posts near the dial

Jan 1, 1954

By Howard A. Meyerhoff, J. Earl Frazier

It is not known when silica sand was first noticed along the north coast of Puerto Rico, but the first mention of its occurrence was made in 1922, by N. L. Britton,1 who described its presence in isolated patches extending from Loiza westward beyond Manati. Further observations were made in 1925 and 1926 by Meyerhoff,2 who extended the known occurrences still farther westward to the low hill belt in the Quebradillas limestone immediately south of Hatillo. The extraordinary purity of the sands, which in most localities exhibit no contamination from the non-siliceous materials surrounding them, was quickly appreciated, and the feasibility of utilizing them for the manufacture of glass was investigated, initially by the Committee on Mineral Resources3 and later (1936) by the Puerto Rico Recon-structionAdministration and by H. C. Ray, mining engineer of the Insular Bureau of Mines. In 1934 samples submitted to the Hazel Atlas Glass Co., of Washington, Pennsylvania, were reported to have the composition as shown in the table on column two. Appreciation of the quality of the sand prompted geological and quantitative studies of the deposits, as well as cornmercial investigations to determine the feasibility of utilizing it locally or on the mainland for the manufacture of glass containers. Distribution of the Sands The quartz sands consistently lie within the outcrop area of the Quebradillas limestone, the youngest of the Miocene formations in the Tertiary coastal plain that fringes the northern coast of the Island. Many of the deposits are closely associated with limestone outcrops, but some appear to be embedded in lagoonal sediments at some distance from rock exposures, and at least one deposit, near Dorado, has been reworked by waves and littoral currents. With this single known exception, the deposits consist of irregular, patternless patches of white sand, which have sharply defined contacts with the surrounding material. Although patches of sand are present in a 90-km. belt that is not more than 5 km. wide, extending from Loiza to Hatillo, they attain maximum size, purity and number in the north central coastal area between Dorado and Barceloneta. Fifty separate deposits have been mapped in Lago Tortuguero and to the south of it, some as small as 50 ft. in diameter but

Jan 1, 1948

By J. Earl Frazier, Howard A. Meyerhoff

It is not known when silica sand was first noticed along the north coast of Puerto Rico, but the first mention of its occurrence was made in 1922, by N. L. Britton,1 who described its presence in isolated patches extending from Loiza westward beyond Manati. Further observations were made in 1925 and 1926 by Meyerhoff,2 who extended the known occurrences still farther westward to the low hill belt in the Quebradillas limestone immediately south of Hatillo. The extraordinary purity of the sands, which in most localities exhibit no contamination from the non-siliceous materials surrounding them, was quickly appreciated, and the feasibility of utilizing them for the manufacture of glass was investigated, initially by the Committee on Mineral Resources3 and later (1936) by the Puerto Rico Recon-structionAdministration and by H. C. Ray, mining engineer of the Insular Bureau of Mines. In 1934 samples submitted to the Hazel Atlas Glass Co., of Washington, Pennsylvania, were reported to have the composition as shown in the table on column two. Appreciation of the quality of the sand prompted geological and quantitative studies of the deposits, as well as cornmercial investigations to determine the feasibility of utilizing it locally or on the mainland for the manufacture of glass containers. Distribution of the Sands The quartz sands consistently lie within the outcrop area of the Quebradillas limestone, the youngest of the Miocene formations in the Tertiary coastal plain that fringes the northern coast of the Island. Many of the deposits are closely associated with limestone outcrops, but some appear to be embedded in lagoonal sediments at some distance from rock exposures, and at least one deposit, near Dorado, has been reworked by waves and littoral currents. With this single known exception, the deposits consist of irregular, patternless patches of white sand, which have sharply defined contacts with the surrounding material. Although patches of sand are present in a 90-km. belt that is not more than 5 km. wide, extending from Loiza to Hatillo, they attain maximum size, purity and number in the north central coastal area between Dorado and Barceloneta. Fifty separate deposits have been mapped in Lago Tortuguero and to the south of it, some as small as 50 ft. in diameter but

Jan 1, 1948

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8.9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3-s in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6.9 The measure of internal friction adopted here, I/Q, is (p) X the logarithmic decrement, a measure used by some writers, and is also (I/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°°C. As shown in Fig. i, the internal friction increased by only a factor of 2 from room temperature to 300°°C., then by a factor of 100 during the next :too' interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction ~ e-HI/RT [I]

Jan 1, 1942

Dubbed "Freeport's Mission Impossible" by the trade press, the company's Ertsberg mine in West Irian nevertheless shipped its first concentrates in December 1972, ahead of schedule. This is a new and great chapter in the history of Freeport Minerals Co. and its contractors. Exploration and construction were only possible by moving equipment and supplies by helicopters. This work was carried out by Petroleum Helicopters, Inc., of Lafayette, La. At the peak of operations six machines were in service manned by 11 pilots and supported by 10 mechanics. During the month of August, with work in full swing 1,604 tons were moved, including 3 DC-6 tractors requiring 18 trips each; flying hours for the month were 636.

Jan 1, 1973

By L. Luini, E. Lee

An exploratory survey of the heat treatment response of commercial titanium alloys (Ti-150A, RC-130B, and MST 3AI-5Cr al-loys) shows a wide range of possible hardness and microstructural characteristics. The hardening is primarily dependent on the solid state transformation of the phase. An age hardening reaction which apparently is associated with ß decomposition and precipitation has been shown. Brittleness and notch sensitivity appear to be characteristic of age hardening to high hardness. Ductility, tensile strengths, and elongations are given. A NUMBER of commercially produced titanium-base alloys have been made available by the titanium metals industry. These alloys were developed to combine the light weight of titanium with increased strength through alloy additions. Usually the properties of these alloys are reported for material in the hot rolled and annealed condition. Since the production of commercial titanium has preceded the investigation of titanium-base alloy systems, the potential of these alloys is not well known. Although heat treatability has been indicated for these alloys, data on the response to heat treatment are quite limited. The heat treatability of titanium is based on the allotropic transformation of the high temperature, body-centered cubic ß structure to the low temperature, hexagonal close-packed a structure at approximately 1625 °F. This transformation in the pure metal is of little practical significance in heat treatment since the high temperature phase is not amenable to controlled transformation. Alloy additions serve to alter the transformation kinetics and permit control of the transformation by heat treatment variables. The effects of different alloys on the allotropic transformation in titanium classify them in two general categories,1 a stabilizing and ß stabilizing elements. The a stabilizers, represented by aluminum and oxygen, raise the temperature limits of the low temperature phase and introduce a two-phase a + ß temperature range. The ß stabilizers, represented by molybdenum and columbium, lower the equilibrium temperature of ß and give rise to an extended temperature range where both a and ß phases are stable. Another type of ß stabilizer, represented by iron, chromium, and manganese, introduces a eutectoid reaction. Some commercial titanium alloys belong to complex multiple element systems. Based upon the phase diagrams of the binary systems, the general effect of commercial compositions is to vary the stability of the high temperature phase and significantly alter its transformation characteristics. Therefore it is expected that the characteristics of alloyed titanium can be altered by heat treatment. The present investigation was undertaken to survey the variations in hardness, microstructure, and mechanical properties as affected by heat treatment variables. Commercial Alloys lnvestigated The commercially available titanium-base alloys selected for this investigation and obtained as 3/4 in. diameter hot rolled and annealed bars are listed in Table I. The producer did not determine the chemical composition of the Ti-150A heats X1052 and L685. The early heats of Ti-150A, prefixed with the letter X, were melted with tungsten-tipped electrodes and cast in approximately 500 lb ingots 12 in. in diameter. The heats prefixed with the letter L were melted under a revised melting practice yielding approximately 1300 lb ingots 16 in. in diameter. The final annealing treatment was at 1200" to 1250°F for 1 hr. The MST-3A1-5Cr alloy was melted in an induction furnace and cast in 7 in. diameter ingots. This practice produces high carbon material and some variation in the amount of carbides was found in different sections of the same bar. The RC-130B alloy was melted with a carbon arc. This alloy showed approximately 2 pct carbides. No large segregation effects were observed.

Jan 1, 1955

By I. W. Wark

AN attempt has been made to compare the influences of the two most widely used depressants-alkalis and sodium cyanide-and the most widely used activator-copper sulfate-on the air-mineral contact induced by five sulfur-bearing compounds: (1) sodium di-ethyl dithio-phosphate (sodium Aerofloat); (2) potassium ethyl xanthate; (3) sodium di-ethyl dithiocarbamate; (4) potassium iso-amyl xanthate; (5) potassium di-n-amyl dithiocarbamate. Three different organic types are included in this group and for two of these types a higher and a lower homologue have been tested. The study of potassium ethyl xanthate, the preliminary results of which have been described,1 was continued until there had been obtained a comprehensive account of the influence of variations in pH value and in the concentrations of xanthate, sodium cyanide and copper sulfate on the adsorption of this xanthate by galena, sphalerite, pyrite and chalcopyrite. With concentrations of copper sulfate and collector that the work with ethyl xanthate indicated would give the most illuminating results, the other four collectors were tested in a less exhaustive way. The same general principles determine the influence of alkalis, cyanide and copper sulfate, no matter to which type the collector belongs, but there is a gradation in the quantitative measure of such influence. In the list above, the five collectors are cited in the order of their capacity to withstand the depressants, sodium Aerofloat being the least resistant, potassium di-n-amyl dithiocarbamate the most resistant. This order coincides substantially with that of the solubilities of the heavy metal salts formed by double decomposition with the collectors, those formed from sodium Aerofloat being most soluble. There is little difference between the third and fourth members of the series, and under certain conditions their positions are reversed.

Jan 1, 1934

By S. J. Kidder, G. C. McCartney

THE Helen Mine, of the Algoma Steel Corporation, in the Michipicoten district, Ontario, Canada, has produced more than 6,240,290 tons of iron ore. Prior to and during World War I, 2,823,369 gross tons of brown ore were shipped, and from 1939 to the end of the 1944 season, 3,416,921 gross tons of siderite ore were produced from open-pit operations. Brief descriptions are given of the nature of the ore, the mining methods employed and the manner of treatment of the ore. Shipment of the finished product, known as Algoma sinter, is made to blast furnaces in both Canada and the United States. The iron-ore bodies-i.e., the oxide ores of the Old Helen and the siderite of the New Helen-are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 ft. and has a maximum width of 1000 ft. The ores are considered to be a product of introduction of iron-bearing material accompanied by replacement of the rocks already present. It is shown that introduction took place subsequent to the development of the major folded structures. It is believed the iron-bearing material emanated from an igneous source.

Jan 1, 1946

By A. W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall, for oreshoots mined were more continuous than drilling indicated. The Geophysics Dept of Michigan Technological University developed a portable induced polarization drill hole probe with a 3-electrode configuration and a sampling radius of 5 ft ±. A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec intervals and readings are taken every 2 ft. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the 1P potential is sampled for 10 ms and recorded. Resistivity (ohm-ft) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous S values noted. The low resistivity amygdaloid contains sills of high resistivity basalt. Verified by core logs, contacts between amygdaloid and basalt could be picked to ± 0.5 ft from resistivity alone. Lithologic logs of long-steel holes, based on resistivity, then replaced sludge logging. An S value of 30 mv/v was established as the lower limit of diagnostic 1P effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found. During the past ten years, the Calumet Div. of Calumet &Hecla, Inc has conducted extensive exploration and mining in the footwall of the Osceola amygdaloid lode in the native copper district in Michigan's Upper Peninsula. In an attempt to delineate more clearly the extent and nature of high-grade footwall copper mineralization, 876 diamond drill and long steel holes aggregating slightly more than 47,000 ft have thus far been drilled from the accessible hanging-wall workings in the Osceola No. 6, 13, 14 and 15 shafts. Early in this program it became obvious, through inspection of footwall workings in progress, that due to the erratic and bunchy occurrence of the native copper in the footwall zone, the exploration drilling was failing to outline completely the extent of the oreshoots. Early drilling re-

Jan 1, 1964

By H. L. Gilbert, C. Travis Anderson, W. J. Kroll

IN a previous paper,1 the use of a split graphite tube resistor as a heater element for high-temperature furnaces has been described. The principal advantages of this type of construction are: I. The quadruple resistance or voltage compared with the top-bottom clamp resistor furnace. 2. Free expansion of the resistor. 3. The ease of protection from oxidation by air. 4. The firmness by which it may be held in the compact split clamp. This construction appeared to be well adapted for the fusion of high melting metals which require fusion in a vacuum. Zirconium metal had previously been melted at the Albany Laboratory of the Bureau of Mines in a vacuum arc furnace on a water-cooled plate, using a movable tungsten top electrode.2 When larger furnace capacities were desired, this type of construction proved to have its limitations as the largest tungsten rods available were about 7/8in. in diameter. The supply of direct current of high amperage for producing the . desired arc characteristics was also not available. Considerable difficulty was also found in compensating the atmospheric pressure on the flexible tubing of the movable electrode, at the same time keeping its movement sufficiently free to enable the striking of an arc on any part of the metal briquet. Among the various materials used for the electrodes in conducting experiments in the vacuum arc furnace was graphite. It was found that zirconium fused in a graphite cup with a carbon arc was contaminated to only 0.2 pct carbon. It was therefore decided to melt zirconium directly in graphite crucibles. A high-frequency furnace was first used in the attempt to melt the zirconium in graphite crucibles. The high-frequency heating coil was placed outside a silica tube which was evacuated by means of an oil diffusion pump backed up by a mechanical pump. The graphite crucible was thoroughly degassed at 1900°C before use. Considerable difficulty was experienced in operating at such temperatures in vacuo because, as shown by Zintl,3 carbon vapor formed and reacted with silica according to the reaction: Si02 + C = SiO + CO. The silicon monoxide which is volatile at these high temperatures reacted with the zirconium, thereby contaminating it with silicon and oxygen. The presence of carbon monoxide was detected by means of a gas discharge tube placed in the vacuum system as indicated by the pale blue glow of the tube as soon as carbon vapor started to react with the hot silica. The reaction between the carbon vapor and hot silica was avoided by the use of split cylindrical molybdenum shields which were inserted between the graphite crucible

Jan 1, 1948

By Russell G. Wayland

THIS paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. MUSCOVITE MICA Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. THE MICA PROBLEM Block muscovite mica is commercially classified into the following general qualities, beginning with the best quality: I. Clear and Slightly Stained (C & SS). 2. Fair Stained (FS). 3. Good Stained (GS). 4. Stained (S). 5. Heavy Stained (HS). 6. Black Spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately I C & SS to 4 FS to 10 GS to 14 S to whatever the

Jan 1, 1944

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By H. N. Eavenson

EaRly in 1917, the United States Coal & Coke Co. secured options on several tracts in Harlan County, Ky., aggregating about 19,000 acres in area, and after careful prospecting by outcrop openings and diamond drilling, completed the purchase late in July of that year. This property is situated in the eastern end of Harlan County, south of the Poor Fork of Cumberland River, and extending across Big Black Mountain to the Clover Fork of Cumberland River, a distance of about 7 mi. (11.3 kg.). It extends from the Kentucky-Virginia line westward for about 6 mi. Looney Creek, which empties into Poor Fork, crosses the property for about 4 mi. (6.4 kg.), and as several of the seams within the property outcrop along this stream, it afforded an easy, and the logical, place for development. The property is on the northern side of the geological trough formed by the uplifting of Stone Mountain, on the southern, and Pine Mountain, on the northern side; the northern boundary along Poor Fork is practically at the base of Pine Mountain. This area has been described in various geological reports. The main seam on this property is the one known variously as the "C," Benham, Keokee, Taggart, and Roda; it is also called, by the Kentucky Geological Survey, the Kellioka seam of the western portion of Harlan County. This seam averages, in this property, about 5 ft. (1.5 m.) in thickness, although local rolls reduce this thickness considerably over small areas, and at the extreme western end of the property the seam splits. It is usually clean, although occasionally a small parting occurs within a few inches of the bottom of the seam; it is one of the best coking and gas coals in the United States. The average analysis of this coal is given in Table 1.

Jan 1, 1922

By Francis M. Rich

BEFORE the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was producing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3: To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as follows: 1 Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimen¬sion of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of Water 1. A particle will move upward if [W > KVr(s-1)] and, by suitably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [T1= s2-1] cannot be separated in an upward-current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of 2.5 sp. gr. Unless 2.5-1 the ratio of diameters is less than [1.35-1 or 4.3 to 1,] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone¬-shaped vessels or vessels of other shapes that allow the use of&apos; different velocities of current at different points in the flow are used to modify this limitation. 3. During the initial stages of motion, coal particles ascend more rapidly than refuse particles of the same size. 4. A particle will ultimately fall if [W < KVr(s-1).] If particles of

Jan 1, 1950