Search Documents

By Richard L. Seal, Allan L. Turner

INTRODUCTION The chapter discusses the procedures and operations starting with the actual training of operations personnel with respect to a grinding mill circuit and a typical check-out and start-up of a grinding circuit before turning over the operating circuit to production personnel. For the purposes of this paper, it will be assumed that the mill circuit installation is at a new location or a new operation at an existing operation. Expansion of an existing grinding facility would probably require less time-consuming and less costly procedures than those that will be outlined here. There are numerous arrangements and types of equipment that can be used for grinding circuits. For example, the grinding could be wet or dry. The grinding mill could be a rod or ball mill or some combination. The circuit could be open or closed. The closed circuit classification could be accomplished with rake classifiers, spiral classifiers, cyclones, stationary screens, or vibrating screens. To limit the discussion, the grinding circuit shown on Figure I will be discussed. The circuit includes a dry ore feed by a belt conveyor (feeder) to a wet ball mill. The ball mill discharges to a cyclone feed pump box and pump. The pump feeds a cyclone type classifier with the cyclone underflow returning to the ball mill feed and cyclone overflow being the required grinding circuit product. For the purposes of this paper, it will also be assumed that the extensive overall preparation necessary for every start-up has been accomplished. These preparations are only outlined here as they have been adequately dealt with in recent papers. (1), (2), (3) The items in these preparations would include. 1. Appointment and indoctrination of the start-up organization. 2. Integration of the start-up into the overall project schedule. 3. Development of the specific start-up schedule. 4. Budget determination and monies appropriation.

Jan 1, 1982

Sec. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whom residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the claw of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1934

By J. Norman Bulkley

As electrical power is used to a greater extent on the Rand than in any other mining center, it is thought that a short description of the methods used and results obtained may be of interest. In comparing Rand practice with that on other fields, several general factors should be borne in mind: First, the mines are all working on large tonnages of low-grade ore (average. $6.50). The annual crushing rate is about 27,000,000 tons. Second, the mines are all grouped udder the financial and engineering control of mining houses, so that the results of a group, rather than an individual mine, are open for study, and practice follows more uniform lines. Third, coal of fair quality (about 12,000 B.t.u.) can be obtained for $2 to $3 per ton., Good supplies of condensing water are, however, scarce, and have to be carefully stored. Power Supply Power is supplied by the Victoria Falls & Transvaal Power Co., Ltd., and its subsidiary, the Rand Mines Power Supply Co. Both companies, which are practically one from an engineering point of view, operate the following stations, all feeding into the same system.

Jan 2, 1916

By A. W. Fahrenwald

THE absolute efficiency of crushing and grinding in a ball mill is not known. A number of investigators have made calculations to this end and have presented efficiency figures. Two factors have prompted further investigation of this subject: (1) the unbelievably low magnitude of the values offered, and (2) a desire to obtain, if possible, true relationships between the relative efficiencies of a ball mill operating under varying conditions. A useful forward step in the study of mill efficiency was made when Martin1 and Gross and Zimmerley2 proved the correctness of Rittinger's law, and incidentally the incorrectness of the so-called Kick law, and when Gross and Zimmerley3 determined and gave surface values for Tyler sieve-sized quartz. These data are probably accurate throughout the range of the sieve scale, but on -400 mesh (which is the finest sieve available), the surface data, as obtained by the hydrofluoric acid disso-lution method, are of doubtful reliability. Any inaccuracy existing in surface determinations of -400-mesh material, especially when comparing runs in which varying quantities of this product are formed, will cause the resulting relative mill efficiency values to be distorted. Moreover, knowing surface accurately, the efficiency calculations require a surface energy figure. Two such figures are to be found in literature, one by Edser4 and one by Martin.5 Edser's surface energy

Jan 1, 1931

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth, W. L. Finlay

Titanium with up to 7.5 pct Al forms single-phase a alloys that are work hardening, not heat treatable, and ductile as welded. The high aluminum Y phase alloys are not usefully ductile, despite their low hardness, but they have excellent oxidation resistance and hot hardness. LITTLE has been published on the effect of aluminum on the mechanical properties of titanium, despite the fact that two of the first four commercial alloys released by titanium alloy producers contained aluminum as an important alloying ingredient. These were both a-ß type alloys, one containing 4 pct A1 and 4 pct Mn and the other containing 3 pct A1 and 5 pct Cr. However, neither of these alloys reflects the true alloying nature of aluminum, since each contains important amounts of the ß-stabilizing addition, manganese or chromium. In a previous publication on the constitution of Ti-A1 alloys,' the authors showed that aluminum had a high solubility in a titanium and was strongly a stabilizing in nature. About 25 wt pct A1 is soluble in a titanium at room temperature. With as little as 5 pct added aluminum, the a transus temperature is increased from 882" to 970°C, and the correspond- ing ß transus to 995°C. The first intermediate phase in the Ti-A1 system is the ordered face-centered tetragonal TiAl phase, which extends from 34 to 46 wt pct Al. The present paper presents hardness data over the entire titanium-rich region of the system, through the TiAl phase, and mechanical property data on the alloy range capable of being fabricated. Methods of Investigation The materials used and general preparation of alloys, as well as experimental techniques used in the investigation of Ti-A1 alloys, have been adequately described.' Briefly, the preparation consisted of arc-melting the desired amount of high purity aluminum (99.99 pct purity) and iodide titanium (maximum hardness 100 Vickers, as deposited) together on a water-cooled copper hearth under a partial pressure of argon. The resulting button ingot was of such form that it could be fabricated without further treatment. All work was done using ingots weighing 10 to 15 g, which were hot-rolled to strip form whenever possible. Tensile samples were 3.25 in. long, 0.5 in. wide, and 0.040 in. thick, with a reduced section 1.25 in. long by 0.250 in. wide. The gage length used was 1 in. Electrical strain gages mounted on the

Jan 1, 1954

By R. T. Hukki

IT is no great exaggeration to say that present grinding practice and economics are largely determined by lining design. A record of outstanding liner wear can be achieved with any liner surface pattern that will positively lock the outer layer or layers of grinding media. With no slippage, lining wear is bound to be slight. At the same time, popular practice calls for tumbling loads of about 50 pct of mill volume to obtain maximum grinding capacity. Innumerable parallel grinding investigations have verified that optimum speed for such a mill lies within 70 to 85 pct of theoretical critical speed. If the mill is speeded up to 100 pct of critical, little or no grinding can be accomplished. Earlier Work on Supercritical Grinding: First investigations concerning grinding at supercritical speeds seem to be very old. Remarkable work on the subject has been performed by White,1 and his experiments have been described and summarized by Richards1 White's contributions seem to have passed unnoticed by Fahrenwald, 2,3 whose extensive experiments have been well presented, yet apparently very little appreciated. Additional work on grinding at supercritical speed has been reported, e.g., by Lewenson and Tscherny,4 USSR; Anselm5 and Grunder,6 Germany; and Rose and Evans,[6] Great Britain.

Jan 5, 1958

By Lo-Ching Chang, K. M. Goldman

The kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was, simple. A graphite crucible 15/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an in- duction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature for 3-5 "'in., aftcr which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 mi11. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the ternperature of the furnace in 1 to 1 1/2 min. Slag

Jan 1, 1949

By K. M. Goldman, Lo-Ching Chang

The kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was, simple. A graphite crucible 15/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an in- duction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature for 3-5 "'in., aftcr which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 mi11. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the ternperature of the furnace in 1 to 1 1/2 min. Slag

Jan 1, 1949

By Joseph T. Singewald

AMONG the genetically interesting iron ores of the United States are those of the St. Francis Mountains near Ironton and Iron Mountain, Missouri. They are specular hematite in porphyry. The Iron Mountain and Shepherd Mountain deposits are generally spoken of as veins and those of Pilot Knob, Cedar Hill, and Russell Mountain as bedded deposits. Iron Mountain has produced nearly 4,000,000 tons of ore and Pilot Knob about 1,500,000 tons. The output of the other three localities has been insignificant. Pilot Knob is no longer worked as an iron mine, but the rock is now being crushed for use as road metal. Iron Mountain has continued as an active producer. In 1927, the property was acquired by the M. A. Hanna Co. and an extensive prospecting and exploration campaign was undertaken, so that the ultimate production of Iron Mountain will doubtless greatly exceed the figures mentioned. Previous Theories of Origin Descriptions of the deposits and theories of their origin have been concerned mainly with Iron Mountain and Pilot Knob, which represent the two contrasting types of occurrence. The Iron Mountain deposits have been considered of close magmatic origin by Whitney' in 18.54, Geijer2 in 1915, and Spurr3 in 1927. Whitney referred to them as of eruptive origin. Geijer considered them fissure fillings at magmatic temperatures. Spurr called them vein dikes formed from ore magma which was essentially fluid iron oxide. Schmidt4 in 1872 ascribed them to fissure filling by thermal chalybeate waters of meteoric origin. Nason5 in 1892 advanced essentially the same explanation. One of the best

Jan 1, 1929

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By Edgar R. Kendall

A KNOWLEDGE of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. LOCATING THE SUPPLY The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1939

By M. Cohen, R. J. Teitel

There is considerable interest in beryllium because of its low density (1.84 g per cu cm), high modulus of elasticity (40 X 106 psi), high melting point (1280°C), and special nuclear characteristics. Moreover, it has fair resistance to corrosion and oxidation. However, the purest beryllium known to the authors is relatively brittle at room temperature, and cannot be fabricated readily. The search for improved properties leads naturally to investigations of beryllium alloys and the phase relationships upon which they are based. The present paper is concerned with the alloys of beryllium and iron, primarily from the standpoint of the equilibrium diagram. Iron was selected (1) because of its all-round importance in metallurgy, and (2) because the beryllium-iron system is known to be quite complex. The most recent diagram in the literature is that of Gaev and Sokolov,' and covers only the iron-rich end up to 16 wt pct beryllium. Beryllium markedly restricts the austenitic field, closing the gamma loop at about 0.4 wt pct (3 at. pct). On the other hand, beryllium is soluble in a-ferrite up to a maximum of 7.5 wt pct (34 at. pct) at the eutectic temperature of 1160"C. The eutectic composition lies at 10 wt pct beryllium (42 at. pct) and corresponds to a mixture of or and FeBez (called j3 in the present paper). The solid solubility of beryllium in the a phase decreases with decreasing temperature, and makes precipitation-hardening possible. These findings substantiate the earlier work of Oester-held,2 Wever and Mueller3 and Laissus.4 In addition to the FeBe2 (ß) mentioned above, Misch6 has reported on FeBes, and indicated evidence for another compound containing still more beryllium. A preliminary diagram by Gordon,5 not hitherto published, is given in Fig 1. Besides the phases previously named, there are shown a solid solution of extended range (e), a compound of limited solubility (t), and a high temperature phase (7). Beryllium is designated as 8. The t field contains the compound composition FeBea, and the f phase undoubtedly corresponds to the beryllium-rich compound found by Misch.6 The region around the { phase was proposed by R. J. Teitel based on Gordon's data. The details of the diagram are self-explanatory. It was the unusual complexity of this system that prompted the authors to undertake the present studies. By the same token, more emphasis was placed on the beryllium-rich than the iron-rich end of the diagram. Exprimental Details RAW MATERIALS The beryllium employed in this investigation was one of the purest grades available. Its chemical analysis after vacuum melting is given in Table 1. The metal assayed 99.4 wt pct beryllium. Vacuum melted electrolytic iron of purity shown in Table 1 was the source of iron.

Jan 1, 1950

By Arthur F. Johnson

THE principal costs of making a pound of aluminum are for 9 kw-hr of electricity and for 1.9 Ib of the oxide (A1203) called alumina. A pound of alumina is made by digesting 2 or 3 lb of bauxite in hot caustic solutions, settling and filtering out the oxides of silicon, iron, and titanium and precipitating and calcining the A1203 as a pure, white powder. The cost of foreign bauxite delivered at an alumina plant in the U.S. may equal or exceed the cost of its chemical treatment to make alumina. Some of the principal factors affecting costs in the utilization of foreign bauxites are: transportation from mine to market, mineralogical and physical composition of the bauxite, thickness of the bauxite beds and their clay and forest overburden, amen- ability of the bauxite to beneficiation and to caustic extraction of the alumina, and lastly size of bauxite deposits and rate of mining employed.

Jan 6, 1954

By Rudolph G. Wuerker

WITH the growing complexity of ore dressing processes and the diversity of equipment, efficiency control has become increasingly important in beneficiation. In the case of iron ore dressing, there have been sporadic attempts'-3 to establish the optimum separation for various ores so that grade and recovery would be readily predictable. But no rigorous statistical analysis and graphical presenta- tion of such tests could be found in the literature of this country. Tests Made with Iron Ores Expanding upon existing methods of plant supervision and efficiency control, an investigation was started in the ore dressing laboratory at the University of Illinois on the applicability of distribution analysis to iron ores. A sample of crude ore was obtained from the Ohio mine of Cleveland-Cliffs Iron Co. at Ishpeming, Mich., consisting mostly of alternating bands of hematite and siliceous gangue, both about 1/4 in. wide. The ore was heavily coated with limonite, which often filled the cracks.

Jan 1, 1959

By Richard W. Lodge

Several methods, both wet and dry, for the assay of zinc-box residues from the cyanide process, have been described in recent years, and each of them has been claimed to be superior to all others. In the year 1901, a paper, entitled "Assay of Zincy Precipitates," was published ill the School of Mines Quarterly to the purport that the scorification method for the assay of zinc-box residues was absolutely unreliable. In order to shed light on this matter, the following experiments were undertaken by Messrs. C.B. Hollis and F. D. Kehew, undergraduate students at the Massachusetts Institute of Technology. The zine-box residues used were obtained through the courtesy of Mr. H. R. Batcheller. The samples were very rich and varied greatly in the fineness of their condition. SCORIFICATION-ASSAYS. In the preliminary tests, the charge, which was weighed on a chemical balance, consisted of 0.1 Assay Ton of residues mixed with from 30 to 35 grammes of test-lead and placed in a 3-in. scorifier, over this an additional quantity of test-lead (from 30 to. 35 grammes) was placed for a cover, and borax-glass, varying in quantity from 3 to 15 grammes, was sprinkled over the top of each charge of the various assays for a cover. The charges were scarified in a muffle-furnace heated to the ordinary temperature which is used in scorification; in some cases the door of the muffle was left open, while in others it remained closed. Generally, the charges spit badly, especially in the assays that were made with door of the muffle left open, or in those in which the door was opened too quickly. The results of the preliminary assays showed: 1. That in order to obtain approxi-

Jan 1, 1904

By H. H. Uhlig

A study of passivity in chromium-iron alloys holds considerable interest, both because of the present-clay practical importance of the stainless steels, and because of the scientific importance attached to the mechanism of their corrosion resistance. Upon the discovery of the passive chromium-iron alloys in 1912, it seemed logical to attribute the observed phenomenal corrosion resistance to a thin, continuous, protective reaction product on the surface. The product was thought to be Cr2O3 or a similar oxide containing both chromium and iron. This mechanism seemed likely in view of Michael Faraday's conjecture that passive iron is not reactive in concentrated nitric acid because of an oxide on the metal surf ace. Since 1912, data have accumulated that permit a further exploration into the nature of passivity and provide a new approach to the problem. A summary of the facts lends considerable weight to a mechanism based not on physical protection of an oxide or similar compound, although such compounds may be present on the surface, but to a change in tendency of surface metal atoms to react chemically. This change in reaction tendency is ascribed to chemisorbed films that effectively satisfy residual valence forces of the metal surface, but do not appreciably disturb the positions of metal atoms in the lattice. In other words, formation of a new lattice such as that of an oxide is not a necessary condition for this type of passivity. The decreased reaction tendency of the metal by reason of chemisorbed films can thereby account for low reaction rates of the stainless steels in many media, as well as a noble galvanic potential as is observed. Substances capable of adsorbing on the stainless steels, and hence accompanying the property of passivity, are typically oxygen, nitrites or chromates, but are not in any sense limited to these. Other elements and compounds can also chemisorb, and therefore may also play a major part in the mechanism of passivity in specific media. The mechanism of passivity based on chemisorption or activated adsorption begins with the interpretation Langmuir proposed for his experiments concerning adsorbed oxygen on tungsten.' He found that adsorbed oxygen was tightly bound, remaining on the tungsten surface above temperatures at which WO3 rapidly volatilizes. The oxygen in such a state did not readily react with hydrogen even at

Jan 1, 1949

By A. J. de Witte

INTRODUCTION The importance of determining dips of subsurface formations in wells, especially in wildcat wells, is self-evident and need not be enlarged upon. Various dipmeter instruments have been described in technical literature1,2,3,4 over the years. The introduction of the continuous dip-meters3,4 has made the earlier types obsolete. Continuous dipmeter logs are run by at least two different major service companies. Included as part of the service are a limited number of dip calculations—usually 10—made at different levels from the log. Very frequently this is the total result of a dip survey. It is believed that dipmeter surveys would be of considerably more advantage if geologists and engineers were able to make their own calculations from the original records. Determination of dips from the dipmeter record starts with the correlation of three log curves taken at different sides of the borehole. It cannot be over-emphasized that the quality of the results hinges primarily on this correlation. Nobody should be better qualified to correlate logs than a subsurface geologist or field engineer. The next requirement is to have an easy yet accurate way of computing the dip from the correlated points. Service companies use a mechanical device for this purpose. Directions for a graphical method were given in a recent article by B. 0. Prescotts. This paper describes a different graphical technique which, in our experience, is simpler, faster and at least as accurate. The entire manipulation is carried out on the stereonet in a number of easy moves. The paper is divided into two parts. This first part contains the introductory sections and full explanation of the geometry involved. The second part reviews the reading of data from an actual field log and summarizes the practical rules for computation of dips, the whole process being illustrated by an example. Following the outlined procedure, one could calculate a good many levels in a relatively short time, thus being able in particular to check suspected anomalies such as fault zones or unconformities in as close detail as the log will permit. GENERAL EXPOSITION OF THE METHOD Prnciple of the Dipmeter The position of a plane in space is defined by the location of three points, not on a straight line. Referring to Fig. I, if a borehole traverses a bedding plane, we can determine the strike and dip of the bed by finding three points which are not in line along this plane. Such points as A, B, and C are obtained with the dipmeter. The device consists of three electrodes (or caliper arms)1, 2, and 3 spaced at 120 angles, as schematically indicated, whose readings are separately recorded (Curves 1, 11, 111, to the right). When electrode 1 passes the boundary of the bed, Curve I will kick, etc. From these curves, we know the relative distances of points A, B, C, measured along the axis of the hole. If A is at zero, then B and C are at levels d1 and d2 up the hole,

Jan 1, 1957

By E. S. Bartlett, D. N. Williams

QUANTITATIVE values for the oxidation rate of unalloyed molybdenum in air at temperatures above the melting point (1460°F) of the characteristic oxide are contained in the literature as a result of previous investigations. Lustman' reported values corresponding to 0.36 in. penetration per day (IPD) at 1500 and 1600°F in still air, noting essentially no variation in rate with temperature. Jones, Spretnak, and Speiser' reported values corresponding to 0.14 and 0.13 IPD at 1500 and 1800°F, respectively, in still air, attributing the decreased oxidation rate at higher temperatures to a lesser accumulation of the corrosive molten oxide on the surface at the higher temperature as a result of increased volatilization rate. Harwood3 ecently summarized work in the field, presenting generalized data corresponding to 0.48 to 0.96 IPD at 1800°F and 0.55 to 0.83 IPD at 1700°F in slowly flowing air. In a recent program at Battelle, it became desirable to know more about the characteristic oxidation behavior of molybdenum under varying conditions of temperature and atmosphere. Using oxidation-test apparatus designed for dynamic, continuous recording of weight change during testing,' values for the oxidation rate of molybdenum were obtained at temperatures from 1400 to 2150°F. In addition the effect of air flow on the oxidation rate was studied briefly at temperatures of 1600, 1800, and 2000°F. Exhaust of the contaminated atmosphere from the oxidation chamber was effected by an impeller pump attached to a 3/16-in.-diam opening in the oxidation chamber. The volumetric exhaust rate (cubic feet per hour) was normally maintained slightly in excess of the input rate to avoid condensation of MOO,,' on the sample suspension rod. The entering atmosphere was preheated prior to admission to the oxidation chamber by a 1 1/2-in.-diam cup packed with shredded asbestos. The experimental data are presented in Table I. Comparing conditions 2 and 3 (taking into account the temperature difference) and conditions 8 and 9. shows that in the absence of forced exhaust an atmosphere of moving air results in greater oxidation rate than a stagnant atmosphere. The use of forced exhaust, as shown by comparing conditions 3 and 4 and conditions 14 and 15: resulted in an even greater increase in oxidation rate. By virtue of the size of the atmosphere input and exhaust openings, it was calculated that the exhaust velocity was about 60 times that of the input velocity for essentially equal volumetric flow rates. Because of the proximity (about 3/4 in.) of the exhaust port to the specimen, it is logical to assume that cleansing of the atmosphere immediately surrounding the specimen was accomplished much more efficiently by the exhaust flow than by the input flow at a constant-volumetric flow rate. Also, it can be seen by comparing conditions 4 through 7 and conditions 11 through 13 that increasing the rate of atmosphere flow (by increasing input velocity with a proportional increase in exhaust velocity) above some optimum value has little, if any, further effect on the oxidation rate. These results suggest that there is a maximum oxidation rate for molydenum at a given temperature which is obtained when conditions are maintained such that the partial pressure of MOO3 in the atmosphere surrounding the specimen is at a low value. By controlling the partial pressure of MOO, surrounding the sample, it is possible to control the rate of volatilization of MOO:, from the surface. This, in turn, affects the rate of oxidation, since the thickness of the MOO3 layer determines the amount of oxygen which will be able to reach the reaction surface.' When the liquid oxide layer is less than some critical thickness, i.e., when the volatilization rate is high, enough oxygen is transported to the active surface to permit oxidation to proceed at the maximum rate allowed by the kinetics of the oxidation reaction. However, if the volatilization of MOO,, is suppressed, the thickness of the layer of MOO3 on the surface increases, and the diffusion of oxygen through the oxide layer becomes the rate-controlling step in the oxidation process. The lack of agreement between the present results and those of previous investigators is presumed to be due to differences in removal of the oxidation product (Moo,) from the immediate vicinity of the sample. By comparing conditions 1, 5, 10, 12 and 14, it is seen that when forced exhaust was used the oxidation rate of molybdenum increased with increasing temperature. A rapid increase was observed between 1400 and 1600°F, attributable to the effects

Jan 1, 1959

By P. Chaudhari, Michael B. Bever

The heat of solution at infinite dilution of selenium in bismuth, the heat of mixing of selenium and bismuth, and the limit of solubility of selenium in bis~rzuth have been determined at 573, 623; and 663°K by metal solution calorimetry. The heat of forrrzation of the compound Bi2Se at these temperatures has been determined from the heat effects associated with the precipitation of the compound from a saturated solution oj selenium and bismuth. The published information on the thermodynamic properties of the system Bi-Se is limited. The heat of solution at infinite dilution of selenium in bismuth at 623°K has been measured.' The heat of formation at 273 K1 and room temperature2 and the heat capacity at 80 K3 of the compound Bi2Se3 have been reported. An estimate of the heat of formation of the compound BiSe at room temperature has been published.2 Information on the phase relations in the system Bi-Se is available.' In the investigation reported here the following quantities have been determined at 573", 623", and 663°K: 1) the heat of solution at infinite dilution of selenium in bismuth, 2) the heat of mixing of selenium and bismuth in bismuth-rich solutions, 3) the limit of solubility of selenium in bismuth, and 4) the heat of formation of the compound BizSe. These quantities were determined by the addition of selenium to bismuth-rich solutions in a metal solution calorimeter. The determination of the heat of formation at the tem- perature of the calorimeter bath involved the precipitation of the compound from a saturated solution in the calorimeter. 5,6 This method differs from that commonly used which requires the addition of the compound and of a mechanical mixture of its components and yields the heat of formation at the temperature from which the additions are made (273 K EXPERIMENTAL PROCEDURE AND CALCULATIONS The solution calorimeter has been described in detail.' Pure bismuth (99.999+ pct) was used as the bath at the start of a run. The calorimeter was calibrated with small amounts of bismuth added from 273°K; the differences of the heat contents of bismuth at 273°K and the temperatures of the baths are listed in Table I. After the calibration, additions of hexagonal selenium (99.999+ pct) were made. Loss of selenium by evaporation was negligible. No unusual experimental difficulties were encountered.9 The differences in the heat contents10 of selenium at 273°K and the temperature of the bath, listed in Table I, were subtracted from the measured heat effects to give the "adjusted heat effects". The methods by which the heat of solution at infinite dilution, the

Jan 1, 1968

By E. J. Fasiska, L. Zwell

PREVIOUS investigations 1,2 of Fe3P described by pearson3 and schubert4 show that Fe3P has a bct unit cell having four Fe3P tetrahedra centered around each lattice point. The space group is 14, No. 82, and all atoms occupy general positions 8(g). The cell dimensions3 are: a = 9.090, c = 4.446 kX, with an axial ratio of c/o = 0.4891. We have measured the lattice parameters of Fe3P, using a Fe as an internal temperature standard, at 23°, 414°, and 678°C and computed the thermal expansion over this temperature range. The Fe,P was prepared by melting under vacuum (after flushing with argon) a commercially pure iron and "ferrophosphor" in a high-frequency induction furnace. Part of the ingot was crushed for X-ray examination and for chemical analysis. X-ray diffraction and light microscopy indicated iron phosphide (Fe3P) present as the major constituent and a small amount (about 5 pct) of a Fe. Chemical analysis showed 0.05 wt pct Si, 0.008 wt pct N, 0.018 wt pet C, and less than 0.02 wt pct each of other metallic elements. X-ray diffraction powder patterns were obtained from a mixture of iron and Fe3P sealed in an evacuated quartz capsule using a Unicam high-temperature

Jan 1, 1968