Search Documents

By Leo F. Reinartz

Part II of a four-part series on the history of steelmaking in the US, points out the inadequate safety and living conditions that existed in steel mills at the turn of the Century. Also defined are furnace and process developments. OPERATIONS in steel plants today are highly mechanized. Men work in light, clean, orderly melting shops, making it difficult for old timers to convince young men that primitive, hazardous conditions existed in steel plants at the turn of the century. Working conditions then were very poor as compared to present day standards. In small plants especially, sanitary, locker, and washroom facilities, first-aid practices and stations were un- known Accidents were frequent and severe. Workers had a fatalistic attitude toward getting hurt. He who had an accident was looked upon as a hero. A dirty bandanna often served as a bandage. Infections were frequent. Electric cranes were in their infancy and broke down often Cables had not as yet replaced chains. Pig iron and scrap iron were loaded by hand in the stockyard, and stockyard locomotives were un- known; mules served as the usual motive power. It was not unusual to see recorded a delay of ½ hr in charging a furnace because of a balky mule. Furnace operations A few plants had primitive charging machines, but most furnaces were charged by placing scrap or pig iron on the paddle of a long peel, which rested on a bar across the furnace door opening. Laborers at the handle end of the peel, using the bar as a fulcrum, would heave the material into the furnace by a down and sideward motion of the peel handle. In time they became expert in placing these materials in the furnace, but it was hard, hot work, and a long time was required for charging. Cold charges of 25 tons required more than 12 hr for melting and re- fining the steel. Ports, doors, and frames were not water cooled. The charging and working area in front of the furnace was covered with steel plates. They were hot and often warped by the intense heat of the un- insulated checker chambers directly below. In the summer, working conditions on the charging floor were almost unbearable. Silica refractories were of poor quality. Because of this, and the inadequate training of furnace men in fuel control and furnace operations, roofs, front and back walls, and ends burned out rapidly. Dolomite machines were unknown; consequently, furnace banks and hearths were fettled with dolomite by the use of hand shovels. The round system required six or more men. Each man took a shovelful of dolomite and, in his turn, deposited it on the back wall and bank by a dexterous forward swing and twist of the shovel. The upward swing of the shovel partially protected his face from the searing heat of the furnace coming out through the wide-open door. Considerable skill and stamina were required to do this job properly. Reverse valves, usually of the cast-iron butterfly type, were located below the charging floor. They were operated by long levers on the charging floor level men they became warped, because of heat and abuse, great strength and skill were required to reverse them. Furnace operations were difficult. The quality and quantity of producer gas coming from irregularly stoked, hand-operated gas producers was uncertain and unreliable. Furnace Linings and ports were quickly burned out. Poor bottom and side-wall refractories, indifferent and inexperienced crews, as well as irregular re-

Jan 1, 1961

By W. A. Ver Wiebe

The year 1940 was singularly unmarked by sensational developments in Kansas. Routine operations were carried on in a systematic, orderly fashion and the efforts of oil producers were concentrated on extending known fields. In Kansas an arbitrary yardstick for wildcats has been set up. A well drilled mile or more from a known pool or well is now considered a wildcat. A "rank wildcat" is one that is drilled at least 2 miles from any known producer. During 1940, rank wildcats resulted in the completion of 116 test wells, among which 16 were successful in finding new oil pools and the remaining I00 were dry holes. The ratio of successful wells to dry holes, therefore, was approximately I:6. During the year, 1890 wells were completed in eastern and western Kansas. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or wells that were recompleted in a different geological horizon. About three fourths of these (1423) were completed as commercial oil wells (I220 in western and 203 in eastern Kansas). The commercial gas wells completed number 58 of which 10 are in eastern Kansas and 48 in western Kansas. Of the remzining completions 147 are dry holes in eastern and 262 are dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year account for a cumulative initial production of 46,000 bbl. in eastern and 2,128,000 bbl. in western Kansas. The state of Kansas attained a new peak in production, with the total of 66,245,000 bbl. for the year 1940, the number of contributing wells being 20,779. Thus the increase over 1939, when about 58 million barrels was produced, is considerable. The previous peak occurred in 1937, when 70,761,000 bbl. was marketed. In another still earlier peak, in 1917, slightly more than 45,000,000 bbl. was produced and sold. The production of gas probably reached a new peak also during 1940, with its total of 85 1/2 billion cubic feet. Between the peak of the year 1908, when over 80 billion cubic feet was produced, and that of 1940, the production dropped to a low point of 16 billion cubic feet in the year 1921. The number of test wells drilled was larger than in 1939; that is, 1890 compared with 1458. The first peak was reached in 1904, when 2782 wells were drilled. The number dropped off rapidly, to 368 three years later, but rose to the second and highest peak in 1918, when 4671 test wells were completed. In the period between 1904 and 1912 more gas wells were completed than oil wells. Between the high peak of completions in 1918 and somewhat lower peak of 1937, the low point was reached during 1931, with the completion of only 470 test wells. In the number of new pools discovered, Kansas again ranks high among the states. The exact number depends somewhat upon the interpretation of a "new" area— whether it should be called a new pool or a long extension of an old pool. Unfortunately, the matter of securing the right kind of production allowable also enters into this question. Often the decision regarding a new pool cannot be made until other wells

Jan 1, 1941

By R. R. McNaughton

The Consolidated Mining and Smelting Company of Canada, Ltd. at Trail, B. C., inaugurated a comprehensive program of investigation about 15 years ago to develop the most economical process of recovering the metal in the large accumulated stock of by-products of the lead smelter and the zinc plant. Two principal methods of recovery were followed to a successful conclusion—an electrothermic process to treat zinc-plant residues and cold slag and the fuming of hot slag from the lead blast furnaces. The latter was selected because it showed a saving over the former in its ability to handle hot blast-furnace slag, thus obviating the necessity of granulating, handling and eventually remelting the same slag for the electrothermic process. The design of a fuming plant was commenced in 1928, and construction, which was started immediately, was completed in July 1030. Operating intermittently for a general tuning up, the plant was officially blown in for regular operation in August. During this month the vagaries of a slag-fuming plant were studied and an operating crew was trained. A history of slag fuming at Trail and the development of plant design is given in a paper by G. E. Murray in the Transactions of the Canadian Institute of Mining and Metallurgy for 1933. Fuming Plant The fuming plant at Trail (Fig. 1) is a separate unit although of necessity interlocked closely with the lead smelter. The plant consists essentially of a fuming furnace with its accessories, a waste-heat boiler followed by an economizer, and a suction-type baghouse. The plant was built as the first of two 400-ton units with the intention of adding the second unit within a year, so that flues, fans and buildings were built to handle double the original load. Furnace.—The furnace as originally built (Fig. 2) was of water-jacket construction, 10 ft. wide, 20 ft. long and 6 to 10 ft. high. The roof height was made variable to check experimental work, which had indicated that this dimension affected the rate of reduction. Coal and air were supplied

Jan 1, 1937

By C. L. Kinney

The rapid increase in the amount of steel produced by the basic open-hearth process is an index of its ability to produce high-grade steel from raw materials of the most, varied physical character and chemical analysis. This inherent adaptability of the process has resulted in a lack of care in the selection of raw materials, so that in far too many cases charges are used of a chemical and physical character not justified by local economic conditions. A practice, or series of practices, should be used that will result in the greatest economy for the plant as a whole; therefore, the operations of blast furnace and open hearth must be considered together. In this paper, an effort has been made to show those variations in both open-hearth practice and cost that follow changes in the analysis of the pig iron arid it may be said that the theoretical costs shown are worthy of careful study and consideration. Carbon, manganese, silicon, phosphorus, and sulfur constitute the principal metalloids in basic pig iron and play the leading role in the production of steel by the basic open-hearth process. The percentages of each of these metalloids, with the exception of carbon, is a variable that has its genesis in the economic relation of the blast-furnace plant to its ore and fuel supplies. As the amount of carbon in the iron is a saturation function of the temperature at which it is produced, the variation in the amount carried is, for any given locality and grade of iron, practically negligible and is so considered in the eight heats discussed in this paper. The melting and refining reactions in an open-hearth furnace, either acid or basic, are essentially oxidizing and vary greatly with the type and age of the furnace, as well as the character of the fuel employed. The outstanding characteristic of the basic process, and the one that explains its predominance over the acid, is its ability to form out of the lime charged and the phosphorus oxidized from the charge a stable

Jan 1, 1924

By Jo. E. Sheridan

The Dawson coal-mines are owned aid operated by the Stag Canon Fuel Co., of which Dr. James Douglas is President and E. L. Carpenter general manager. The property is situated in Colfax county, N. M., and the openings now in operation are in townships 28 and 29 N R. 20 E., and township 28 N E. 21 E., shown in Fig. I. The mines are part of the southern end of the Raton coal-field, which extends north into Colorado and embraces many coal-camps of the Trinidad section. II. Geology. Geologically, the coal-measures, commonly known as the Laramie series of the Cretaceous system, have x thickness of about 800 ft. in the vicinity of Damson. The coal makes an excellent coke, and, according to some authorities, its coking properties are due to the action of intruded sheets and sills of igneous rock, the sheets occasionally thickening into masses resembling laccoliths, at such places making nearer approach to the coal and sometimes producing small areas of natural coke. There are but few dikes throughout the entire southern portion of the field and little or no faulting along the dikes. In some parts of this great coal-field the intrusive sheets are far removed in the green shales below the coal-measures, and are so much altered as to be difficult of identification. There is but little disturbance of the strata throughout the Raton coal-field in as far as it extends into New Mexico. There are two workable seams in the coal-measures, and two or three smaller coal-seams, ranging from 1 to 2.5 ft. in thick-

Jan 1, 1910

By E. S. Davenport

IT is indeed an honor and a responsibility to have been selected to present the thirty-fourth in this series of Henry Marion Howe lectures, established to perpetuate the memory of a great teacher and one of America's outstanding scientists. Previous Howe lecturers have established high standards for this annual AIME event. It has been my good fortune to have enjoyed close association with five of these former lecturers; namely, Bain, Grossmann, Johnston, Sosman, and Vilella, all of whom have been prominently identified with the research activities of the organization with which I am connected. Some years ago I had an opportunity to examine a letter written by Professor Howe in 1904. This document was particularly interesting to me since I never had the privilege of personal acquaintance with Professor Howe and do not recall even having seen him during his long and active career. In view of the fact that the letter dealt, to some extent, with matters related to the subject of today's lecture, I would like to quote briefly from it. The letter is datelined, "Bad Kissingen, June 11, 1904." The salutation reads, "Dear Bradley," which suggests that it was probably addressed to Bradley Stoughton, who, I believe, was working with Howe at Columbia University at that time. The letter reads, in part, as follows: "Austenite and Martensite. I have not examined what Osmond says in his new book. His former remarks about austenite I found very confusing, indeed unintelligible. I think we can reconcile matters well enough for the present by assuming that martensite is a transition step between austenite at one end and ferrite and cementite at the other. Above critical range for steel of 0 to 1.80 carbon, austenite is normal state; below Ar1, ferrite and cementite are normal." The letter then continues with a discussion of Osmond's ideas on metallographic nomenclature, particularly his use of the terms martensite, troostite, and sorbite, including the following pointed comment: "For common purposes it seems to me unwise to drag them in, and much simpler to confine ourselves to the end stages Austenite Ferrite plus Cementite Osmond does not really know his own mind— or does not clarify his ideas to others—as to nomenclature." Thus we see that, as far back as 1904, the transformation of austenite, and the products of that

Jan 1, 1958

By James P. Kimball

Sulphur is always present in mineral coal of every variety. In the oxidized state it may exist as sulphuric acid in combination with a base. In the unoxidized state it exists in combination with iron as bisulphide of iron. It is also supposed by some chemists to exist in unknown combinations with the organic elements of the coal. This supposition requires the demonstration as a fact that certain coals yield more sulphur than what may exist in a free state, or what belongs to recognized combinations, not only with the accompanying iron but with other inorganic bases abundantly occurring in coals, but which unfortunately are very rarely estimated. This practically as well as theoretically important question it is at present impossible to decide, simply for want of available thorough ultimate coal analyses including the ash. Such analyses, at the best imperfect, are luborious and intricate, and therefore seldom made, the much simpler proximate analyses, so-called, being resorted to by most chemists for technical purposes, and commonly substituted for more scientific work even in the laboratories of government surveys. And it is unfortunate enough that few ultimate analyses are extended to the composition of the ash, much less to its relation to the original constitution of the coal. Sulphur chiefly occurs in most coals in the form of yellow pyrites (pyrite) and white pyrites (marcasite), both minerals, characterized by differences in crystalline form and in physical properties as well as in color, but having the same chemical composition (FeS2). No coal is entirely free from one or both of these dimorphous forms of bisulphide of iron. It may be disseminated through the mass so as to be invisible, in plates or scales between the laminæ of the coal, or in conspicuous segregations or nodules, sometimes of considerable dimensions. Coals greatly differ as to the proportion of sulphur which they contain. They also differ as to the relative proportion in which its several forms of combination occur. Such qualitative and qnantitative disparities arc scarcely, if at all, more marked in separate coal seams of a uniform type than in different parts of one and the same coal seam, whether it be considered locally as constituted of several

Jan 1, 1880

By O. P. Chisholm

Dross emerges from the blast furnace either with the lead through a lead well or by tapping from a forehearth or settler, but until a dozen years or so ago few dross reverberatories were used in western lead smelters because it was the usual procedure to circulate the dross from the drossing lead kettles back to the blast furnace. It was quite customary for lead smelters to produce matte in their blast furnaces, as this was the form in which copper could be collected, concentrated if necessary, and shipped to the copper smelters for further treatment. The main prerequisites for good matte formation arc., of course, a more or less definite amount of copper on the charge and sufficient sulphur. Such troublesome impurities as arsenic and antimony were ignored, in so far as possible, although they contaminated the bullion and thereby increased refinery costs. At the same time stocks of blastfurnace speiss containing gold, silver, lead and copper in addition to iron, arsenic and antimony, were being accumulated for want of a market to absorb them. As the dross was being fed back to the furnaces as rapidly as it was being produced, arsenic and antimony tended to build up until the arsenic could effect a combination with copper and iron and an alliance with lead, and the antimony a combination with copper and an alliancc with lead. Sulphur, being the most active agent in taking up the copper, left little of that element for the arsenic and antimony, so that on the whole a somewhat unsatisfactory metallurgy resulted. During this same period, certain lead plants were beginning to encounter trouble with zinc due to the replacement of crude ores of lot zinc content by concentrates containing high percentages of lead and zinc in sulphide form, the blast-furnace slags resulting from the smelting of such concentrates being characterized by a decidedly increased zinc content. It was soon realized that zinc plus sulphur was "poison" to a lead blast furnace and steps were taken to reduce the sulphur content,. At this stage some plants found that any substantial matte fall was out.

Jan 1, 1937

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. INTRODUCTION IT has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse' presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941

By Francis F. Lucas

A microscope objective of given numerical aperture, when used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability—the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise when the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500 uu and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.60 N. A. are now an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Kohler and Dr. M. Von Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 uu which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 1, 1926

By Robert Lewis

THE Utah coal field to which the name Book Cliffs is applied runs in a northeast direction from Mt. Hilgarde, in Sevier county, along the escarpment of the Wasatch Plateau to the vicinity of Castle Gate, thence southeast along the Book cliffs, which lie to the north of and generally within sight of the Denver & Rio Grande Railroad,. to the Colorado line. The Book cliffs form the southern escarpment of the West and East Travaputs Plateaus, and vary in height from 2,000 to 6,000 ft. At the base of the Wasatch and Book Cliffs escarpments is a broad plain known as Castle valley. The coal beds outcropping in the escarpments along this valley are worked on the largest scale of any in the State, and this particular area is known locally as the Castle Valley coal field. Geology The Book cliffs are capped by the Tertiary-Eocene-formation, consisting of varicolored shales; buff sandstone, conglomerate, and subordinate thin beds of limestone. Different sections show diverse stratigraphy. This is mainly the Wasatch formation, and lies unconformably upon the rocks of the Upper Cretaceous. Fig. 1 is a generalized section of the rocks of the. Book Cliffs field. The Mesaverde formation contains the cliff-making rocks of the Book cliffs, and is composed of massive sandstone interbedded with sandy shales and beds of coal and carbonaceous shale. The sandstone has greater resistance to erosion and the formation is characterized by escarpment ledges and cliffs. The shale is commonly sandy and is drab in color, but where it is associated with the coal it is usually carbonaceous. The sandstone is generally buff, though occasionally it is white, and in places red. The bedding ranges from thin to massive. In the lower part. of the formation the sandstone is red in

Jan 7, 1914

By Burt C. Mariacher

To note that environmental considerations had a major im¬pact on the minerals processing industry in 1971 would be something less than a profound observation. The degree of its importance was demonstrated by MBD when it established the Environmental Committee as a new unit committee within the Division to achieve greater participation in exchange of information relating to the technologies and problems involved. It is appropriate and necessary to devote special attention to this timely aspect of minerals processing, as its influence penetrates the research, engineering and operations of almost all unit technologies that comprise minerals processing. The pollution abatement aspect of this industry has been such a dominant factor in recent years there is reason to wonder whether progress in unrelated technologies has been curtailed. Perhaps so, to some degree, but unit committee reviews presented in this article suggest rather that it would appear to have served as a catalyst for accelerated progress in development of new methods and improvement in more conventional ones. Present concepts regarding primary metal or mineral recovery and by-product potential may change considerably as a result of improved technology in waste product treatment.

Jan 2, 1972

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold ; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1964

By D. S. Newton

Introduction Historically the production of zinc dust has been based upon residual and secondary zinc. Using horizontal retorts filled with diecasting scrap, galvanizers drosses and sweater billets, dust has been produced by condensation into static condensers on a 24 hour cycle. Although fairly flexible as regards input materials the process is not amenable to close control of the product, is labour intensive and unless carefully run can cause fume problems. With a steadily increasing demand for zinc dust of consistent properties and higher quality there is a demand for an improved method of manufacture in which dust can be produced continuously and which is capable of close control thus ensuring a minimum amount of oversize or unsaleable material. The Process in use in the works of Imperial Smelting Corporation (Alloys) Ltd. in England, and in Canada and Holland, satisfies the criteria stated above, and has proved to be easy to control with a minimum labour demand.

Jan 1, 1970

By Larry Kaufman, Joan B. Berkowitz-Mattuck, Edward V. Claugherty

The oxidation characteristics of hafnium and zirconiunr diboride were measured between 1200 and 2200'K by a thermal- conductivity method which continuously ttzeasures the rate of reaction of oxygen with the diboride and by a metallographic air oridation method zuhich provides a measure of the total arr7ount of bovide conuerted to oxide for a given time interval. The oxidized specimens obtained from the tl~eritaal-coi~ductitrity method were also examined by quantitatire metal-lographic procedares. The significant results obtained in this investigation reveal that metal-rich compositions of lzafi~iutil diboride proride the most oxidation-resistatzt material up to 2000°K; hafnium diboride is tmre oxidation- resistant titan zirconium diboride at all tempevatures examined; the morphology of the oxide formed on H/B2 and Llie temperature coefficient qi. the oxidation rate constants change at the temperature of ttze monoclinic to tetragonal phase transition] in HfO2; the oxidation of neither HfB2 nor ZrB2, results iN catastrophic Jazlure at lorc. oxygen pressures; and pvefevetztial gvaLti boundary oxidation was not obsevued for either HfBi or ZYB, A comprehensive study of the high-temperature characteristics of refractory transition-metal di-borides is currently in progress. This program has included investigation of the physical, thermal, and thermodynamic properties of TiB2, ZrB2, HfB2, NbB2, and TaB2. In addition, aspects of the synthesis and fabrication of such materials have been studied. In view of the diverse nature of this research, a number of other laboratories have actively participated and contributed specific capabilities for analysis and characterization of these materials. As a consequence, an extensive description of the relevant properties of these compounds has emerged which is central in evaluating their high-temperature (1200" to 2500°K) performance. To date, information on thermodynamic stability, specific heat, and vaporization characteristics,1 hot hardness and electrical resistivity,1, 3 therma1 expansion:'4 and thermal conductivity 1, 5 has been presented. This information has been generated on materials of the highest purity (98.5 to 99.9 wt pct Me + B) and density currently available. Samples fabricated by zone melting6 and high-pressure hot pressing"3'7 techniques have been used to generate suitable specimens for all of the aforementioned studies. dation characteristics of the most oxidation-resistant of these materials, hafnium and zirconium diboride, is presented and a description of the synthesis and the experimental procedures used to prepare and characterize specimens is given. The high-temperature range under consideration (1200" to 2200°K) and the known dependence of oxidation characteristics on sample chemistry, density, and oxidation conditions required a close coupling of the synthesis, fabrication, and evaluation procedures.8 This was accomplished by continual surveillance of chemical composition of starting materials before and after specimen fabrication and by evaluation of density, phase constitution, and microstructural features prior to and after oxidation exposure. I) PROCUREMENT AND CHARACTERIZATION OF STARTING MATERIALS In view of the current state of the art in fabricating refractory boride materials, the methods used in preparing samples for the present study are given in detail as follows: starting materials were purchased in high-purity powder form and fabricated by high-pressure hot pressing into 0.40 by 1.00 in. bars from which oxidation specimens were obtained. The hafnium diboride used in this study was purchased from Wah Chang Corp.; the zirconium diboride from U.S. Borax and Chemical Co. These powders were routinely characterized by quantitative chemical analyses for metal, boron, carbon, oxygen, nitrogen, and iron, by qualitative emission-spectrographic analysis for trace impurities, by X-ray procedures for extraneous phase identification, and by powder densitometry for comparison with X-ray (theoretical) density. Hafnium and zirconium metal and elemental boron were also purchased as high-purity powders and characterized for impurities by emission-spectrographic analyses. The hafnium diboride was procured in three shipments which were designated as HfBl.g7(1), HfB1.88(2A), and HfB2.12(2). The indicated stoichiometry is based on the atomic ratio of total boron to total hafnium; the number in parentheses identifies the shipment number. Shipment 1 was 5 1b, shipment 2A, 1 1b, and shipment 2, 8 1b. The zirconium diboride was procured as a 20-1b shipment and designated as ZrB1.89(1). A small quantity of purified zirconium diboride was also supplied and designated ZrB1, 9(P). The averaged results for chemical analyses which were generally performed according to the procedures set forth in the compilation by KrieGe9 are presented in Table I. Qualitative spectrographic analyses indicated that Ca, Cr, Ti, Si, Zr (in H~B~), and A1 were present at levels between 0.01 and 0.10 wt pct. Other metallic elements were found to be less than 0.01 wt pct. Since it is virtually impossible to purchase these materials in the desired quantities (5 to 20 lb) as single-phase compounds it is necessary to obtain

Jan 1, 1968

By R. Wang, N. J. Grant, B. C. Giessen

By crystallographic and X-ray methods, the existence and isonzorphism of Ti3Rh5 and Hf3Rhs were confirmed. Both phases are of the orthorhombic Ge3Rh5 type; lattice parameters and refined positional parameters are given. The structure is related both to the filled-up NiAs-B8 and Cu-AI types. An analogous phase with zirconium does not exist; the effect of ternary substitutions for titanium ad hafnium suggests a size factor limit to be active. A recent survey of phase diagrams of the T4 metals titanium, zirconium, and hafnium with the T, noble metals rhodium and iridium indicated the existence of the A3B5 phases Ti3Rhs, ZrsRhs, and HfsRhs. Ti3Rhs and Hf3Rh5 were found to be isostructural, based on the line-rich powder patterns which had not been analyzed. Zr3Rh5 was considered to have a substructure of the NbRu type (orthorhombically distorted B2-CsCl type).&apos; Because, in combinations with other transition metals, hafnium and zirconium are generally more likely to form isostructural phases than hafnium and titanium (with the significant exception of the Ti2Ni-"E93" type phases based on T4 metals2), the reversal of this relation for the A3B5 phases was of interest. As shown in the following, the nonexistence of Zr3Rhs has been established, the structures of Ti3Rh5 and Hf3Rh5 have been worked out, and crystal chemical relationships and stability criteria are reported. EXPERIMENTAL METHODS AND RESULTS Alloy Preparation and Phase Diagram Work. Alloys were prepared from high-purity (99.99+ pct) elements by arc-meltin3,4.Heat-treated alloys were annealed in a vacuum of 3 x X torr for 24 hr at 1300DC. Metal-lographic samples were etched electrolytically in concentrated HCl with 5 v ac for 5 min.3 X-ray diffraction powder patterns were taken on a GE XRD-5 dif-fractometer with Cum radiation at low scanning rates (0.2 deg per min for 28). It was confirmed that Ti3Rhs and Hf3Rh5 have similar diffraction patterns, and that an alloy with the composition Zr3Rhs has a different pattern. Six Zr-Fh alloys with 59 to 69 at. pct Rh were therefore prepared and investigated in the as-cast state by X-ray diffraction and metallography. Alloys at 59 and 61 at. pct Rh were found to be a single phase, with the distorted B2-CsC1 type structure typical for the off-stoichio- metric region of the phase (Zr,-,Rh,)Rh. This phase forms a eutectic with ZrRhs at about 66 at. pct Rh: accordingly, alloys between 61 and 69 pct at. pct Rh consisted of two phases. There is no evidence for the existence of Zr3Rh5. Based on the results in Rafs. 1 and 5, on the present work on Zr-Rh, and on several additional alloys investigated, the portions between the AB and AB3 stoi-chiometry for Ti-Rh, Zr-Rh, and Hf-Rh are as follows: Further, several ternary alloys near Ti3Rhs and Hf,Rhs were prepared in which it was attempted to replace titanium and hafnium partly by zirconium, niobium, tantalum, and germanium. The results will be discussed in a later section. Structure Determination of Ti3Rh5. Since Ti3Rh5 and Hf3Rh5 are isostructural, the following discussion will largely deal with the former. Although the powder pattern of TisRhs is complex, as found previously,1 it could be indexed by comparison with other structures of A3Bs stoichiometry. Ti3Rh5 was found to be isostructural with Ge3Rh5, whose orthorhombic structure had been elucidated by Geller.9 As both the sizes and atomic numbers of germanium and titanium are comparable, the unit cell volume and the peak intensities could be expected to be similar; however, significant differences exist in the atomic positions, as will be shown. All lines in the powder patterns of Ti3Rh5 and Hf3Rhj could be indexed with primitive orthorhombic unit cells with the lattice constants: The fractional errors are 10 The low-angle portion of the indexed powder pattern of Ti3Rh with sin2 8 < 0.30 is listed in Table I. The extinction laws Okl only with k = 2n and hOl only with h - 2n are compatible with the space group Pbo2 and the more symmetrical space group Phnm of Ge3Rh5. Finally, the positional parameters of Ti3Rh5 and HfsRhs were refined under the assumption that titanium and hafnium occupy the germanium positions in Ge3Rh5. Integrated intensities were obtained from the diffraction patterns by planimetry. Intensities of overlapping reflections were separated by an iteration process incorporated into the least-squares positional refinement program according to a method described previously. The intensities of Ge3Rh5 were used in the first separation cycle, while the atomic parameters of Ge3Rh5 were used as starting values in the first refinement cycle. Absorption due to specimen

Jan 1, 1970

By B. H. Sage, R. T. Carter, W. N. Lacey

The phase behavior of a number of binary systems consisting of parafin hydro-carbons has been determined in recent years. In addition, the composition of the coexisting phases of mixtures of crude oil and natural gas has been investigated.~ However, the latter study did not include information concerning the influence of the concentration of a component upon its distribution between two coexisting phases. Owing to the paucity of such information it was considered desirable to investigate in some detail the composition of the coexisting phases in the methane-propane-n-pentane system throughout the greater part of the two-phase region at a tempera-ture of 100°F. Information of this nature also permits the establishment of the critical behavior of this ternary system. Method The compositions of the coexisting phases in this ternary system at 100°F. were deter-mined by withdrawing samples from a pres-sure vessel containing a heterogeneous mixture of the three components that had been brought 10 equilibrium by mechanical agitation at the desired pressure and tem-perature. The samples were withdrawn under such conditions that the equilibrium was not disturbed and the composition of each of the phases was ascertained by means of the conventional low-temperature fractionation procedure. The apparatus employed in this investi-gation was nearly the same as that utilized in an earlier study of the methane-pentane system.~ Several minor modifica-tions in the arrangement of the apparatus were made in the interest of simplifying the procedure and avoiding the possibility of condensation in the tubing connecting the equilibrium apparatus with the analyti-cal equipment. The pressures were meas-ured by means of a pressure balance with a precision of 0.5 lb. per sq. in. It is believed that the equilibrium pressure was ascer-tained with an uncertainty of not more than 2 lb. per sq. in., even though small varia-tions in pressure obtained during the withdrawal of the samples. The tempera-ture of the equilibrium equipment was maintained by use of an automatically controlled oil bath. The bath temperature was determined by means of a copper-constantan thermocouple, the electromo-tive force being determined by means of a potentiometric circuit of such a nature as to reduce the uncertainty of the tempera ture to less than O.I f. The fractionating column employed in the determination of the composition of the gas phase had a diameter of 0.12 in. and was approximately 4 ft. long, while the column employed in the analysis of the liquid phase was 0.18 in. in diameter and about 5 ft. long. Each column was equipped with the conventional constant-volume receivers, which were maintained at a constant temperature by means of an automatically controlled oil bath. In nearly every case the distillation in thr neighborhood of the transition between

Jan 1, 1941

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana&apos;s northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming&apos;s Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By Thomas T. Read

The cost of labor turnover in industry is so large as to justify the adoption of almost any means to bring about its reduction. Intensive study has shown that faulty methods of hiring and discharging men is the most important factor in labor turnover. Complete control over hiring and discharging by the foreman is a relic of outgrown industrial conditions; centralized hiring permits this work to be put on a scientific basis and also does away with many serious evils that cannot, otherwise be reached. Centralized hiring does not impair the authority of the foreman; he hires his men from the employment office and discharges them back to it, instead of from and to the street. The employment manager, being a direct representative of the employer, tends to restore the former relation of direct intercourse between employee and employer that was helpful in avoiding friction between them. Being a specialist,, he is able to bring special knowledge and skill to bear upon the task of selling employment in his concern to desirable workmen; he is also able to give the foreign workman the special attention he requires. Employment managers have been used for the past few years by a number of large organizations, a few of which are engaged in the mining and rnetallurgical industries. They have invariably reduced labor turnover, in some cases to as little as one-tenth of what it had been. So great a reduction is due in part to other changes made in the light of the data made available by scientific study of the labor problem. In my former paper on personnel work&apos; I advocated the more general use of the employment manager in mining and metallurgical enterprises as a means of reducing labor turnover. The form of organization recommended seems not be to understood by all, and I have requested the privilege of explaining it at greater length, since it is perhaps the most important factor of all in personnel work, and has a vital influence on the cost sheet of every industrial enterprise.

Jan 1, 1918

By G. P. Boomslitter

In previous discussions on stresses in hoisting ropes, little has been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured. Theoretical Discussion According to elementary physics, the force required to accelerate a Wf body of weight W at the rate of f ft. per sec.2 is wf . To raise the body Wf with acceleration of f ft. per see.2 the total force required is I + Wf, in if

Jan 1, 1927