Search Documents

By G. S. Scott, G. W. Jones

ECONOMIC waste caused by mine fires may become considerable,15 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters-such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control. necessarily must be based upon one or the other, or both, of these two principles. . The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion) ; and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. OXIDATION OF COAL Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored.6,16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By Lester C. Uren

THIS paper reviews the industrial trends and changes in educational concepts that have led to the development of the modern petroleum engineering curriculum. A trend toward emphasis on engineering fundamentals is noted. While most universities are committed to the traditional four-year engineering program, it is agreed that more than four years is necessary for academic preparation of the petroleum engineer in all phases of his profession. The author proposes a coordinated program of undergraduate and graduate training that will permit of adherence to the general pattern of the present four-year engineering course, with provision for extension of the program into specialized graduate courses of professional character. In the latter, emphasis may vary with the interests and objectives of the individual student. A specific undergraduate curriculum is proposed in which upward of 80 per cent of the available time is devoted to engineering fundamentals. A broad survey of the professional field is afforded in courses grouped in the third and fourth undergraduate years, but detailed treatment of the professional aspects of petroleum engineering is reserved for the graduate program. INTRODUCTION Of necessity, engineering curricula must ever be changing to reflect the new techniques, the changing concepts that are presented as the engineering industries develop and unfold. Particularly is this true of the younger engineering curricula representing comparatively new and rapidly changing industries such as the petroleum industry. Institutions that planned their petroleum engineering curricula a decade or two ago now find that the petroleum industry has become vastly more technical in its requirements. Entirely new methods and techniques have come into vogue and must be given place in the curriculum, and some of these are of a character that demands changing emphasis in the fundamental preparatory subjects. College and university faculties cannot complacently assume that curricula in this field that were considered appropriate 10 or 20 years ago still reflect the needs of the industry that they are designed to serve. If they do, their graduates will be poorly equipped to meet the requirements imposed upon them by a rapidly changing industry. Perhaps it is not too much to expect academic authorities to anticipate the trends of industry and equip their graduates with what they will need to attain leadership 10 or 20 years after graduation. Whether or not this desirable objective is possible, there is no excuse for allowing curricula to fall behind the current needs of industry. DURATION OF CURRICULUM The majority of our engineering schools and colleges still adhere to the four-year curricula and there appears to be a definite - sentiment among many engineers engaged in industry that work should be so planned that the engineering student may secure the essential academic preparation for his profession in a terminal four-year program. Yet, in recent years, it has become increasingly apparent that four years of

Jan 1, 1941

By William F. Cerini, Willis R. Battles, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company's experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.' It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well' The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By R. T. Hukki

John F. Myers (Consulting Engineer, Greenwich, Corm.)—Since the art of comminution has lain practically dormant for many years, it is very interesting that R. T. Hukki approaches the subject with a new concept. One is reminded of the research carried on by A. W. Fahrenwald of Moscow, Idaho, a few years ago. Fahrenwald mounted a steel bowl on a vertical shaft. The balls and ore placed in the bowl were rotated at fast speeds, thus simulating the supercritical speeds used by Hukki. The rolling action of the balls against the smooth shell liner has pretty much the same effect. The action is horizontal in one case and vertical in the other. Both researchers report good grinding activity. It is also constructive that such able investigators give to the students of comminution their interpretation of their laboratory results in terms of large-scale operation. History shows that it takes a lot of time for such radically new ideas to be absorbed by the industry. Typical of this is the present-day activity of cyclone classification in primary grinding circuits. The idea of cyclone classification has been kicking around for 30 or 40 years. Certainly we all suspect that the ponderous grinding mills of today, and their accessory apparatus, large buildings, etc., will ultimately give way to small fast units, just as this has occurred in other industries over the past 50 years. At the moment there is no evidence that ball and liner wear is prohibitively high. In fact, at the time Fahrenwald was demonstrating his high-speed horizontal machine at the meeting of the American Mining Congress, several years ago, he assured this writer that the balls retained their shape much longer than they do in conventional tumbling mills. Rods and balls that slide (as some operators in uranium plants are experiencing) get flat. Apparently the balls have a rolling action. Mr. Hukki's references to the processing capacity of the Tennessee Copper Co. mills is adequate. Those studying this subject will be greatly interested in the paper presented by Richard Smith of the Cleveland-Cliffs Iron Co. at the annual meeting of the Canadian Institute of Mining and Metallurgy in Vancouver April 24, 1958. This paper will be published during the latter part of 1958 in the Canadian Institute of Mining and Metallurgy Bulletin. Hukki's pioneering spirit is to be commended. R. T. Hukki (author's reply)—It has been heartening to read the objective discussion by J. F. Myers. The sincerity of his opinions is further strengthened by the fact that the article he has discussed contradicts in a major way the parallel achievements of his life work. Myers is right in his opinion that in general it takes a long time before new ideas are accepted by the industry. On the other hand, revolutions usually take place at supercritical speeds. There are many indications at present that both the unit operation of grinding and the related subject of size control are now just about ripe for a revolution. In grinding, brute force must ultimately give way to science. Rapid progress can be anticipated in the following fields: 1) Autogenous fine grinding at supercritical speeds will be the first advance and the one that will gain recognition most easily on industrial scale. At this moment, little Finland appears to be leading the world. Crocker recently made a statement that in nine cases out of ten, your own ore can be used as grinding medium more effectively and far more economically than steel balls. This is true. The present author would like to introduce a supplementary idea: In eight cases out of the nine cited above, it can be done at the highest overall efficiency in the supercritical speed range. Fine grinding must be based on attrition, not impact. The path of attrition may be vertical, horizontal, even inclined. 2) In coarse grinding, the conventional use of rods is sound practice. However, even the rods can be replaced by autogenous chunks large enough to offer the same impact momentum as the rods. To obtain the momentum, the chunks must be provided with a free fall through a sufficient height in horizontal mills operated at supercritical speeds. Coarse grinding must be based on impact. Detailed analysis of the subject may be found in a paper entitled "All-autogenous Grinding at Supercritical Speeds" in Mine and Quarry Engineering, July 1958. 3) All conventional methods of classification, including wet and dry cyclones, are inefficient in sharpness of separation. Continuous return of huge tonnages of finished material to the grinding unit with the circulating load is senseless practice. In the near future the present methods will be either replaced or supplemented by precision sizing. These three fields are also the ones to which J. F. Myers has so admirably contributed in the past. Fine Grinding at Supercritical Speeds. By R. T. Hukki (Mining EnGineERInG, May 1958). Eq. 9, page 588, should be as follows: T , c, (a — 6') n D Ltph On page 584 of the article the captions for Figs. 4 and 5 have been placed under the wrong illustrations and should be interchanged.

Jan 1, 1959

By Eric R. Morgan, J. C. Shyne

STRAIN aging is the name given to time-dependent changes which occur in the properties of cold-worked metals and alloys during storage. These changes are best observed through a study of mechanical properties, as illustrated in Fig. I for low-carbon steel. The effects of strain aging are usually regarded as being detrimental, particularly in deep-drawing steels. For example, an increase in yield strength and loss in ductility lead to buckling and tearing during drawing. At the same time the return of the yield point results in the formation of Luders bands or stretcher strains during the pressing operation. As a result of these effects many attempts have been made to eliminate strain aging from low-carbon steel. The problem still remains, however, because all known methods of preventing strain aging result in a more costly steel. The present work is an assessment of the situation in terms of theoretical, practical, and economic factors and suggests a new solution to the problem. Previous Work According to the Cottrell theory,' strain aging in a-iron may be regarded as the migration of interstitial atoms to free dislocations and the anchoring of dislocations by the resulting atmospheres. It may be concluded that the important factors which will govern the degree of strain aging are the diffusivity, the effective amount of interstitial element in solution, and the time of aging. The diffusivities and effective amounts of carbon and nitrogen in solution in low-carbon rimming steel are such that significant aging occurs in a few hours' storage at room temperature. Strain aging in deep-drawing steels cannot be controlled by controlling the time of aging because in commercial practice this is determined by economic factors concerned with inventories and may be several weeks. The diffusivity of nitrogen is twice that of carbon at room temperature but the diffusivities can be controlled by controlling the storage temperature. The retardation produced by only a 25 °C drop in temperature is significant but the cold storage of large steel inventories is an impractical solution to Table I. Analysis of Base Materials Alloy Pet C Yet 0 Pet N Vac 0.0037 0.052 0.0003 H 0.0044 0.013 0.0008 C 0.06 0.0014 0.0001 the problem. By far the most simple and effective ways to control strain aging are through control of the amount of carbon and nitrogen in solution. This may be effected through alloying, controlled precipitation, or by eliminating the carbon and nitrogen. Consider first the control of the amount of carbon in solution. The simplest approach would be alloy -ing in which strong carbide-forming elements are added. Examples of this approach are the additions of titanium' and niobium9 0 steel. These elements also combine with nitrogen and oxygen and when added in sufficient quantity result in a completely killed and non-aging steel. They are, however, impractical additions because they result in a costly steel. Carbon and nitrogen are often removed from iron on a laboratory scale by annealing in wet hydrogen, but because of cost this process has never been adopted on a commercial scale. In practice the amount of carbon in solution is controlled by the rate of cooling from the annealing temperature (710°C or 1310°F). In commercial box

Jan 1, 1958

By Mark D. Tabak

Measurments of the transient photoconductivity in fillns of amorphous selenium with blocking- contacts haue been used in studying the transport properties. The results shozu that the transport of free carviers cannot be explained in terms of a model using bulk trapping. Measurments of the photocurrent-applied field characteristic as a unction of sample thickness do not pvoduce the scaling lau,s approps-iate lo a range-limited model. THE investigation described here was undertaken to explore the mechanisms of transport in amorphous selenium films. These films are used in xerography, where a photoconductor is charged electrostatically and then exposed to light to form a latent image. The sensitivity that one can expect when operating in this mode is directly related to the transport properties of the photoconductor material. The study of photoconductivity at high fields in insulating materials is often complicated by contact effects. Injection from the contacts can easily mask the fundamental transport processes that are being studied. A technique is described in this paper that allows a study of photoconductivity and transport processes in amorphous selenium films without the complicating effects introduced by contacts. Accordingly, the samples are prepared using insulating films between the sample and the metal electrodes, where the electrodes are capacitively coupled to the surfaces of the sample under study. A transient measurement is performed with pulsed light, and the photocurrent measured near the beginning of the pulse before the field is distorted by polarization at the blocking elec- trodes. A similar method has been described by Manyl using pulsed electric fields in studying the high field transport in insulating cadmium sulfide. EXPERIMENTAL It is possible to eliminate undesirable contact effects and maintain uniform high fields across the sample by using blocking electrodes and measuring the current-field characteristic under transient conditions. The sample configuration is shown schematically in Fig. 1. Each of the gold electrodes is separated from the amorphous selenium film by a layer of insulating plastic (Formvar) approximately 2000~ thick. The electrode on the front surface is semi-transparent to allow illumination of the sample. The whole configuration is mounted on a KEL-F substrate, which is a transparent insulating plastic having a thermal expansion coefficient that allows low-temperature measurements without cracking the selenium film. Fig. 2 shows a block diagram of the measurement apparatus. Light was obtained from a 450-w Xenon arc lamp, the intensity of which was controlled by stainless-steel screen filters and monitored by a pho-tomultiplier which was calibrated periodically against a thermopile. A camera shutter operated at 1/200 sec provided the light pulse and a synchronized signal to the oscilloscope. The photocurrent transient is ob-served with a high-speed picoammeter (response time of 1 msec) the output of which is displayed on an oscilloscope. The applied voltage is constant throughout the transient measurement. The selenium films were prepared by evaporation of four 9's pure selenium shot supplied by Canadian Copper Refiners. Spectrographic analysis showed about 1 ppm of Te and Fe, 5 ppm of C1, and 0.05 ppm

Jan 1, 1968

By B. B. Sandiford

It has been known for many years that the efficiency of a water flood can be improved by lowering the water-oil mobility ratio in the system. Such a change leads to better sweep efficiency and also to more efficient oil displacement in the swept zone. Data from our laboratory water-flood tests of both small cores and long sand packs are presented which show that water mobility can be reduced and oil recovery increased by the addition of certain polymer solutions to flood water. The reduction in mobility, in many cases, is greater than would be expected from conventional viscosity measurements. These solutions, however, do not cause significant reductions in oil mobility. The over-all effect of these mobility changes is increased waterflood oil recovery. Encouraged by results of our laboratory work, we expanded our study to include pilot field tests of floods with such solutions. One such test, made in the West Cat Canyon field, Santa Barbara County, Calif., is described in detail in this paper. Three other field tests are also discussed. INTRODUCTION Oil production from most reservoirs following primary depletion and/or water flooding is often less than 50 per cent of the original oil in place. Heavy oil reservoirs seldom yield over 15 per cent of their original oil. With new reservoirs becoming harder to find, the improvement of oil recovery efficiency is one of our very important problems. We describe here some of our attempts to increase the efficiency of oil displacement by adding a water-soluble polymer, partially hydrolyzed polyacrylamide, to flood water. This technique will be termed "polymer solution flooding". The concept of using high-viscosity water to increase the efficiency of water flooding is not new. In 1944 Detling (Shell Development Co.) obtained a patent covering the use of several additives for viscous water flooding.' His objective was to improve water-oil mobility ratios by increasing the viscosity of the flood water. Other patents2-27 have been granted covering specific water-SO~LIble polymers or specific conditions of viscous water flooding. Barnes'" described his laboratory model study of the injection of a viscous water slug into a reservoir which had been partially invaded by bottom water. He concluded that, for this type of reservoir, "the cost of viscous water should not exceed a few cents per barrel for viscous water slug injection to be economically feasible" Our studies have led us to a somewhat different conclusion in a number of cases where hydrolyzed polyacrylamide solutions have been injected into reservoir models or actual reservoirs. Possible reasons for this difference are discussed in this paper. Our studies have shown that polymer solutions may lead to an increase in oil recovery over that from an ordinary water flood by (1) improving sweep efficiency, (2) improving microscopic displacement efficiency, or (3) a combination of these mechanisms. In the work of Barnes, only the benefit of improved sweep efficiency was considered. Also, our work has shown that there are marked differences in the effectiveness of different water-soluble polymers as flood water additives. Partially hydrolyzed polyacrylamide is better than many other water-soluble polymers we have tested because, even in very low concentrations, it can lead to increased oil recovery. This is an important advantage when either a dilute polymer solution is injected continuously or a relatively concentrated slug is injected followed by water. In the latter case! portions of the slug become diluted and function in the formation as very dilute solutions. As dilution takes place the effective slug size will increase which, in turn, will reduce the cost per barrel of the effective flooding medium. The reason that partially hydrolyzed polyacrylamide solutions are more efficient at low concentrations than certain other polymer solutions of equivalent viscosity (when measured in conventional viscometers) is not fully understood. We do know that the shapes and sizes of macro-molecules dissolved or suspended in liquids influence the flow properties of their solutions or suspensions. Solutions of partially hydrolyzed polyacrylamide cause greater reductions in water mobility than would be expected from conventional viscosity measurements. LABORATORY STUDIES Laboratory water floods were run in linear and radial systems with different water-soluble polymers and under varying conditions of flow. including reservoir conditions of temperature, pressure and fluid composition. Some of these runs are considered in this section. OIL DISPLACEMENT IN LINEAR MODELS In this group of runs the sweep efficiency approached 100 per cent because the linear sand packs used were as nearly uniform as possible. Results reflect primarily the micro-scopic displacement efficiencies. The laboratory models were unconsolidat-ed sand packs the lengths of which varied from about 4 in, to 40 ft. Further information on the flow models used is listed in Table 1. Using conventional procedures, water floods were run on sand packs containing either refined or crude oil at restored state. Frequently, a repeat run, similar to the first, was made as a check. Then a third run was made on the restored-state model using either polymer solution or a combination of polymer solution (slug) and water. Details of these runs are also reported in Table 1. In Figs. 1 and 2 results of two different groups of runs are shown in which the oil used was a 62-cp refined oil and the flooding medium

Jan 1, 1965

By A. Totani, S. Nakajima, H. Okazaki

The phase diagram for the SnTe-SnSe system has been studied in the temperature range from 300° to 900°C by differential thermal and quenching techniques. The X-ray measurements were made on quenched specimens. High-temperature diffraction was also made to study the phase transition in SnSe. The system is proved to be of a eutectic type in which no intermetallic compound exists. The eutectic point is at the composition SnTeo.55 Seo.45. the eutectic temperature being 755°C. Solid solubility limits are SnTeo.6Seo.r and SnT eo. 3s Seo.6s at the eutectic temperature, and change almost linearly to SnTeo.aaSeo.lz and SnTeo.18 Seo.az as temperature decreases to 300°C. It was shown that the SnSe phase has a phase transition of the second order at about 540°C and that the transition temperature decreases with increase of the SnTe content. THERMOELECTRIC properties of tin telluride (SnTe) and tin selenide (SnSe) have been studied extensively in recent years. The variation of physical properties with composition could be of interest if these compounds form an appreciable crystalline solution. The purpose of present investigation is to confirm the formation of crystalline solution or intermetallic compound, if any, and to establish the phase diagram for this system. The crystal structure of SnTe is NaCl type with a cubic unit cell1 (a = 6.313A). The crystal of SnSe having an orthorh2mbic unit cellz (a = 11.496, b = 4.1510, and c = 4.4437A) is isomorphous with tin sulfide (SnS) which has a distorted sodium chloride structure. It has been known that SnSe has a phase at at 540°C; the transition has been assumed to be of the second order. As far as we know, only two studies on the SnTe-SnSe pseudobinary system have been reported. The conclusion obtained in these papers is that, in the composition regions near SnTe and SnSe, the system forms a crystalline solution of the SnTe structure and the SnSe structure, respectively, and that, in the intermediate region, both phases coexist. However, neither the variation of the solid solubility vs the temperature nor the liquidus and solidus were investigated. Hence present writers have attempted to determine the phase diagram of the system by differential thermal analysis (D.T.A.) and X-ray diffraction. EXPERIMENTAL Sample Preparation. Starting materials, SnTe and SnSe, were prepared by the direct fusion of commercially available high-purity (99.999 pct) elements. Stoichiometric amounts of each couple Sn-Te or Sn-Se were weighed into a clear fused silica ampule. After evacuation to a pressure below 10-3 mm Hg, the am- pule was sealed, and annealed at 900°C for 5 hr. The melt was quenched in water. X-ray analysis confirmed the formation of a single phase of SnTe or SnSe. The other samples, SnTel-,Sex were synthesized from these SnTe and SnSe by mixing them in the required ratio, followed by annealing at 900°C and quenching. These samples were used directly for D.T.A. For X-ray measurements, samples were annealed at 700°, 600°, or 500°C for 100 hr or at 300°C for 150 hr, and then quenched in water. It was found that the lattice constants of the SnTe phase annealed for 150 hr at temperatures above 500°C did not differ from those annealed for 100 hr at the same temperatures. However the X-ray phase analysis showed that at 300°C the annealing for 150 hr was necessary to attain a true equilibrium state. D.T.A. The solid-liquid equilibrium temperature was determined from D.T.A. measurements. The sample was sealed in an evacuated silica tube and molybdenum powders sealed in an another tube were used as a reference material. The sample and the reference tube were placed in a nickel block and were heated from room temperature to 900°C at a rate of 3°C per min and then cooled down at the same rate to 600°C. Thermocouples for these measurements were Pt-Pt. Rh (10 pct) and the error of temperature measurements was within + l0C. D.T.A. curves were obtained on a two-pen recorder and an automatic controller (PID type) was used for the program of heating and cooling. When temperature reaches the solidus from the low-temperature side, there appears an endothermic peak. The solidus temperature was determined by extrapolation of the straight portion of the starting flank of this peak to the base line. In a similar way, the liquidus temperature was determined from an exothermic peak on D.T.A. cooling curve. In the case of supercooling, if any, its degree can be estimated from the magnitude of the abrupt temperature rise. X-Ray . X-ray powder patterns were taken by a diffractometer using CuK, radiation. Since the SnSe crystal is cleaved easily, the powders become flaky when SnSe-rich samples are ground in an agate

Jan 1, 1969

By Arthur Phillips, R. M. Brick, A. J. Smith

A previous publication1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuAl². A similar study has been made of the aluminum-rich aluminum-magnesium alloys. Attention has been directed in the present investigation to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic defomation or cracking has been considered in relation to the physical properties of the alloy On reheating alloys in the two-phase field, the time required for precipitation to occur has been observed in connection with the degrec of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys. Strain in Solid-solution Alloys A 10 per cent magnesium alloy ill the form of chill-cast bars was furnished by the Aluminum Company of America through the courtesy of L. W. Kempf. Additional alloys were prepared using alllminum (99.95 per cent Al) and high-grade magnesium. The alloys listed in Table 1 were melted in an Acheson graphite crucible under a flux of fused MgCl², CaC12, NaCI. Chill-cast rods were sealed under vacuum in Pyrex glass, homogenized several days at 450' C., air-cooled and machined to rods of from 1/8 to ¾-in. dia. Metal powders taken from these rods with a fine-toothed saw were again sealed under vacuum in

Jan 1, 1935

By R. M. Brick, Arthur Phillips, A. J. Smith

A previous publication1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuAl². A similar study has been made of the aluminum-rich aluminum-magnesium alloys. Attention has been directed in the present investigation to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic defomation or cracking has been considered in relation to the physical properties of the alloy On reheating alloys in the two-phase field, the time required for precipitation to occur has been observed in connection with the degrec of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys. Strain in Solid-solution Alloys A 10 per cent magnesium alloy ill the form of chill-cast bars was furnished by the Aluminum Company of America through the courtesy of L. W. Kempf. Additional alloys were prepared using alllminum (99.95 per cent Al) and high-grade magnesium. The alloys listed in Table 1 were melted in an Acheson graphite crucible under a flux of fused MgCl², CaC12, NaCI. Chill-cast rods were sealed under vacuum in Pyrex glass, homogenized several days at 450' C., air-cooled and machined to rods of from 1/8 to ¾-in. dia. Metal powders taken from these rods with a fine-toothed saw were again sealed under vacuum in

Jan 1, 1935

By T. E. Scott, R. P. Zerwekh

The charactevistics of the deformatiotz of fcc thorium were examined between 78 and 473 K. Activation energy, actiuation volume, and the temperature dependence of the flow stress were determined and conlpared uith several theories for the rate-controlling mechnnistn of the tempemture-dependent component of the flou~ stress. It was established that the Cottrell-Stokes law does not hold, even approximately, for thorium. Through consideration of the above factors and other parameters, it was concluded that the vandom solute barrier theory proposed by Friedel demonstrates the best agreement with experimental observations of the deformation of thorium below ambient temperature. THORIUM, the first metal in the actinide series of rare-earth elements, is interesting and important from two points of view. In the more practical vein, it is a potential reactor fuel. As such, it is important to know its properties. Of specific interest here are the mechanical properties of thorium. Second, no detailed information concerning the deformation characteristics of the actinide elements has been gathered to date. In view of the interesting physical and chemical properties of these metals, their mechanical behavior might reveal characteristics which could improve our understanding of the mechanisms controlling deformation of the more common metals. For example, it has been shown1 that thorium exhibits a yield point which is greatly enhanced by interstitial solute elements such as carbon. This is not a normal occurrence in fcc metals. The goal of this investigation, therefore, was to characterize the deformation of polycrystalline thorium. MATERIAL AND PROCEDURES Thorium, made by the magnesium intermediate alloy process described by Peterson et al.,2 was rolled and swaged to 0.065-in.-diam wire. The metal analysis is given in Table I. After preparation, the oxygen and nitrogen contents had risen to 308 and 60 ppm, respectively. The 0.065-in.-diam wires were cut into 2-in. lengths and annealed in a vacuum of lo-' Torr at 750°C for 1 hr, producing a grain size of 2735 grains per sq mm. The ends of the 2-in. sections were masked off so that a 1-in. gage length could be electropolished. Specimens were polished at 35 v in a solution of 6 pct perchloric acid in methanol which was maintained at 0°C . The gage diameters after polishing were about 0.0625 in. The tests were run on a screw-driven tensile machine at a constant crosshead speed corresponding to a strain rate of 0.005 min-'. The strain rate was changed rapidly after each 0.01-in. extension between 0.005 min-' and one of three higher strain rates which were selected in order to achieve strain-rate ratios of 5, 10, and 20. Tests were run at several temperatures from 78" to 473°K; most were tested at 423", 300°, 215", and 78°K. EXPERIMENTAL RESULTS Flow Stress vs Strain and Temperature. Typical true stress-true strain curves for thorium are shown in Fig. 1 for several temperatures over the range 473" to 78°K. The curves for 78", 215", 300") and 423°K were obtained from strain-rate change tests using the lower (0.005 min-') or base strain-rate values of stress. Additional tests, using the same base strain rate at different strain-rate ratios, gave curves which virtually superposed on those shown, indicating that strain-rate changes did not materially influence the work-hardening characteristics at the base strain rate. The curves for 273") 373") and 473°K were standard tensile tests at 0.005 min-'. The behavior of the flow stress with temperature is

Jan 1, 1968

By George M. Enos, Robert J. Anderson

An impoRtant factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2-mm. (equivalent focal length) apochro-matic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002 to 0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002 to 0.0004 mm. thick. This thickness is equivalent to 50,000-

Jan 1, 1925

By Glenn C. Waterman

THE diamond drill is a very important tool in exploration and development testing and its use is increasing. In almost all cases results of diamond drilling are analyzed on the basis of grade and tons. A proper evaluation of core and sludge assays is important if drilling results are to be acceptable as a basis for geologic and engineering appraisal. The relatively wide variation in assay averages as calculated by various well-known combining methods indicates that the engineering choice of a method may affect the outcome of the drilling in terms of ore and waste. The problem of combining assay results from core and sludge samples has been discussed many times in conference and in the literature.'-' Most writers agree that the field of disagreement in methods is large and that the engineer on the job must consider features unique to his drilling, pick one of several combining methods, and depart from the rules when abnormal results come in. All the discussion to date can be summed up by the admission that as yet there is no fairly simple, generally acceptable combining method that is practicable over a wide range of drilling conditions, ground conditions, and ore occurrence. The combining problem is important in evaluating drilling results at Chuquicamata. Recently a reappraisal has been made of recovery variables and their effect on assays, with the result that a new combining method is offered which fits average drilling conditions and is mathematically reasonable. It is simple in application, fundamentally correct, and an improvement over most combining methods. At Chuquicamata diamond drillholes are used to outline the grade and position of blocks of normal and marginal grade oxide, mixed, and sulphide ore. Most holes penetrate all classes of material (and waste), and it is important for mining programs as well as ore reserves to know almost precisely the soluble and insoluble copper content of mineralized ground. At present three classes of ore are mined and treated differently. For an orderly sequence of mining operations which can provide regular daily tonnages of all three ore types and keep grade at certain levels with minimum variation, ore type and its grade must be predicted. Diamond drilling plus geologic mapping and bench sampling are tools for prediction. And drilling data are largely used to calculate grade of material more than a few meters away from bench faces. The orebody at Chuquicamata" is criss-crossed by millions of barren or mineralized weak to fairly strong slips and fault fissures. Mineralization is diverse and encompasses many quartz and oxide or sulphide-bearing copper veins, as well as seams and disseminated grains. Copper occurs in oxide or sulphide minerals or mixtures of these two mineral types. Rock conditions vary from intensely seri-citized (soft and porous) through clay-altered ground to almost fresh granodiorite. The result is an orebody which offers many obstacles to good and consistent core recovery in diamond drilling. Recovery varies considerably in the several alteration zones, the various types of oxide and sulphide ores, and the position and inclination of the drillhole within the complex fracture pattern. As core recovery drops sludge samples must be used with core samples to calculate grade. Many years of drilling at Chuquicamata indicate that in good grade oxide zones and in the sulphide areas core recovery is good and the ground uniformly mineralized. Moderate loss of core, therefore, does not markedly affect grade calculations based on core assays. An early core-sludge combining method used core assays at face value as indicating grade down to 50 pct core recovery, but below this recovery percentage sludge samples were used and weighted according to the standard Longyear chart. This method apparently did not introduce serious errors, but it abruptly used sludge assays with high weighting factors representing 100 pct return irrespective of actual percentage of sludge recovered. Recent drilling activities have been directed toward outlining the marginal ore areas. The non-uniform mineralization and generally poorer core recovery in such ground indicated that a more exact core-sludge combining method was required to equate wide differences between core and sludge assays and recovery. In fringe ore areas at Chuquicamata core recovery averages about 50 pct, from a minimum of 10 to 15 pct to a maximum of 100 pct. Sludge recovery is likewise variable and averages perhaps 80 pct even though holes are cemented as water return falls off. In a homogeneously mineralized area cut by many slips and faults, with hard and soft ribs, loss of core is loss of ground which has a grade similar to that of core recovered, and core assays approximate true grade. In this case sludge samples need not be used. However, it would be unusual to know beforehand that an area is uniformly mineralized, and in fact this condition is probably uncommon. Generally the distribution of valuable minerals in the ground does not exactly compare with their recoverability in core. Thus, in the usual case, loss of core decreases the

Jan 1, 1956

Jan 1, 1942

Jan 1, 1909

Jan 1, 1965

Jan 1, 1929

State Mine Experiment Station, College of Engineering, University of Alabama, University, Ala Copies of two bulletins issued by the Mine Experiment Station may be had by writing to the Director of the School of Mmes at the above address: Bulletin 1, Coal losses in Alabama, 2, A specific gravity study of Alabama coals The Cooperative work of the Mine Experiment Station with the Southern Experiment Station of the U S Bureau of Mmes is covered by Bulletins of the U S Bureau of Mines

Jan 1, 1933

Jan 1, 1941

At a meeting of the Board of Directors, held Jan. 21, 1916, the following resolution was adopted: Resolved, that this Board has learned with indignation and sorrow of the unprovoked and brutal murder of 18 American citizens on January 10, in the State of Chihuahua, Mexico, and laments especially the death of Messrs. C. R. Watson, C. A. Pringle, H. C. Hase, and W. J. Wallace, who were members of the American Institute of Mining Engineers. As these men and their companies were engaged, in the lawful prosecution of their work, we trust that nothing will be allowed to prevent or delay appropriate action by our Government concerning the outrage by which they lost their lives;

Jan 3, 1916