Search Documents

By Persifor Frazer

IN his “Final Report," Vol. II, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

Jan 1, 1877

By J. F. Peters

The term solution loss is discussed and defined. Examples are given showing that solution loss may either have a favorable or unfavorable effect on blast furnace performance. A theory is advanced explaining the contradictions encountered during earlier studies of the problem. MANY papers have been written and numerous theories advanced concerning the chemical reactions in the iron blast furnace. Richards, discussing the utilization of fuel in the blast furnace, said: "All the carbon burnt in the furnace should be first oxidized at the tuyeres to CO and all the reduction of oxides above the tuyeres should be caused by CO, which thus becomes CO,. This dictum is not Gruner's own words, but expresses their sense, and from the point of view of the present discussion, it is the correct principle upon which to obtain the maximum generation of heat in the furnace from a given weight of fuel." Richards also said the cubic feet of wind per pound of coke does not express how efficiently a furnace is running, but it will be shown later where Howland paid much attention to this figure. Richards pointed out a shortcoming of Grun-er's discussion in that Richards claimed there is not enough CO generated in a good working blast furnace to possibly combine with the oxygen of the ore, so some of it must be reduced by solid carbon. Mathesius2 made two important contributions. First, he wrote the direct and indirect reduction equations showing the heats of formation in each case and stressed that the indirect reduction reaction produces heat while direct reduction absorbs heat. Secondly, he substantiated Richards' conclusion that there may be a deficiency of CO gas and that some direct reduction is required, but he pointed out that "direct reduction in the hearth has often been confused with direct reduction in the stack, which more correctly should be termed 'premature combustion'." Then he said that "as this carbon is consumed partly by economical (direct reduction in the hearth) and partly by wasteful reactions in ever varying proportions, it is evident that the relation of this total carbon gasified above the tuyeres to the fuel consumption of a furnace cannot possibly have a direct bearing on the economy of furnace operation. The premature combustion of carbon (CO2+C?2CO) must therefore in all cases be considered a detrimental reaction." Johnson3 discussed this whole problem. Through experience Johnson found that when departure from Gruner's ideal working is considerable, the fuel economy is poor, and when the quantity of blast goes up, the fuel economy goes up in the same proportion. Johnson said that the wind per pound of coke is a measure of fuel economy, which will be shown to be wrong. Howland4 established the fact from operating data that there was no relationship between the coke consumption of a furnace and the percentage of coke burned at the tuyeres. But some of his calculations have led to questionable conclusions, such as "it is practically impossible to obtain low coke consumption unless we keep our wind low." Howland made an important contribution when, in his concluding paragraphs, he reached certain negative decisions as to why one coke works better than another. He said the reason one coke works better than another in a blast furnace is not because: 1—there is any difference in the percentage gasified at the tuyeres, or 2—there is any difference of wind required per pound of coke. Korevaar5 propounded a new theory on combustion which disagrees with Gruner because "as far as we can see, this is sufficient proof for the invalidity of Gruner's ideal, for if it was valid, the Low coke consumption should always be accompanied by a higher percentage of carbon burned at the tuyeres. This not being the case, we must deliberately give up our belief in Gruner's ideal." The part in italics will be proved to be wrong. Martin" contended that there was not enough reducing capacity in the blast furnace unless solution loss occurs. He came to a series of conclusions, such as: 1—The greatest efficiency of the blast furnace may not be attained when the reduction is performed entirely by carbon monoxide as demanded by Gruner's definition of the ideally perfect working of the blast furnace. 2—The so-called solution loss reactions, which should more properly be termed direct reduction reactions, promote furnace efficiency. 3—In modern blast furnace practice, the carbon consumption of the process is determined primarily by the carbon needed for reduction purposes, any thermal deficiency created by the reduction process being balanced in practice by the use of blast heat. From a practical standpoint further discussion of the theory of chemical reactions is of little moment. There is however one phase of the general theory of chemical reactions which is very important and that is the combustion of coke in the blast furnace. The purpose of this paper is to show that the reaction

Jan 1, 1955

By S. R. Seagle, R. Schuhmann, N. A. Parlee

Rates of CO evolution and CO absorption were measured for liquid-iron alloys containing from 0.15 to 4.4 pet C, using a modified Sieverts apparatus. The alloys were held in alumina crucibles, so that both crucible-metal and gas-metal reactions occurred simultaneously. The data are interpreted on the hypothesis that the C-O reaction rate is controlled by oxygen diffusion across the boundary layers at the gas-metal and crucible-metal surfaces. CARBON-monoxide evolution from liquid Fe-C-0 alloys is a key reaction in steelmaking processes, both in the steelmaking furnace and in the ingot mold. Also, this reaction probably is an essential step in the desulfurization of iron under blast-furnace conditions, for which carbon is the principal reducing agent or deoxidizer present in the iron. The thermodynamic properties of the solutions of C and 0 in Fe and the equilibria of these solutions with gaseous CO and CO, have been investigated in some detail and are reasonably well understood. However, while these equilibrium data have accumulated in the laboratory, other data have accumulated to show that equilibrium conditions are often not achieved under plant operating conditions. Thus, an understanding of the rate and mechanism of the carbon-oxygen reaction not only has theoretical interest, but ultimately may assume considerable practical importance. Reaction Mechanisms and Rate Equations The over-all reaction under consideration is C (in liquid Fe) + 0 (in liquid Fe) + CO (gas) [I] Although this appears to be a straightforward heterogeneous reaction, involving just two phases (liquid metal and gas), a wide variety of reaction mechanisms has been proposed. Different authors have expressed divergent views as to the nature of the rate-controlling steps. Accordingly, a brief discussion of the possible reaction steps will be given. 1) Homogeneous Reaction Within Liquid Iron— Feild' and Jette2 have applied chemical reaction-rate theory as if the C-0 reaction were a homogeneous, second-order reaction occurring within the liquid-metal phase. This mechanism necessarily produces CO "molecules" dissolved in liquid iron. In order to yield CO gas, the dissolved CO must nucleate CO gas bubbles, and the dissolved CO also must be transported to the bubble surface where it enters the gas phase. However, this mechanism is inconsistent with present concepts of the structure of liquid-metal solutions. 2) Reaction at Gas-Metal Interface—At the surface of contact between gas and metal, a second-order reaction between dissolved C and 0 may occur to produce a CO molecule which enters the gas phase. This reaction presumably involves an "activated complex" structure in the interface. Some such surface mechanism appears essential because the carbon and oxygen do not occur in the same species in the two phases and therefore must react in some way at the surface. At liquid-iron temperatures, calculations based on reaction-rate theory indicate that the surface reaction must proceed extremely rapidly and thus cannot be a rate-determining step in the C-O reaction under ordinary conditions.3 ccordingly when the over-all reaction is measurably slow, the surface reaction may be considered at equilibrium; that is Cc* Co* = m'Pco [2] in which Co* and Co* are the concentrations of carbon and oxygen (weight per unit volume of metal), respectively, in the liquid-metal phase at the interface, Poo* is partial pressure of CO in the gas phase at the surface (atmospheres), and m' is the mass-action constant for Reaction [I]. Since activities of C and 0 are not strictly proportional to concentrations, m' is not a true thermodynamic equilibrium constant but varies with carbon content.' 3) Mass Transport—If the reaction is to proceed at the gas-metal surface, as described above, dissolved carbon and oxygen in the liquid iron must come to the surface and gaseous carbon monoxide must move away from the surface. Details of the mass-transport mechanisms depend on the kind of system under consideration. For a stirred metal bath in contact with a CO gas phase, the transport of C and 0 to the surface can be described by 1 Do Mols CO evolved per sec = — 1/16— Do/do Agm (CO-Co*) = 1/12 Do/do Agm *(Co-Co*) [3] In this equation, Do and D, are the diffusion constants for oxygen and carbon in liquid iron, 6, and 6,. are the boundary-layer thicknesses, A,,,, is the

Jan 1, 1959

By I. R. Kramer

The stress associated with the surface layer was deter-minedfor iron and molybdcnum. These measurements show that the surface layer plays a very important role in the plastic deformation of bcc metals. From the relationship between strain arui the surface layer stress and the back stress imposed by the internal obstacles, it is Proposed that the term of of the Hall-Petch equation is related only THE large number of studies on plastic flow of bcc metals have failed to delineate clearly the nature of the obstacles influencing dislocation movement. Since there have been numerous articles which have reviewed the mechanisms proposed to explain various aspects of plastic flow of bcc metals (for example, conrad1 and Keh and weissmann2), no attempt will be made here to discuss their conclusions. However, it should be to the surface stress while the term Kfd is the stress required to move dislocations through internal obstacles. Further, it was possible to derive the well-known empirical equation C = , and it is shown that the terprz a is comprised of two terms: a term Cs associated with the surface layer stress and Ci related to internal dislocation obstacles. pointed out that in all of these publications it has been tacitly assumed that plastic flow occurred uniformly throughout the cross section of the specimen (except, of course, for the Luders band region), It has generally been further assumed that the nature and distribution of the obstacles opposing the motion of dislocations are of the same type throughout. The role of the surface layer in bcc metals has not, as yet, been considered even though its role in fcc metals has been shown clearly to be of primary importance.3-5 Investigations on fcc metals have shown that at the onset of plastic deformation a surface layer acts to

Jan 1, 1968

By Prince Gelasio Caetani

PRESIDENT DWIGHT'S invitation to be a guest of the American Institute of Mining and Metal-lurgical Engineers was the first of the subsequently very numerous invitations to dinner I have received from my American friends. When I received his telegram I had not yet been even formally appointed Ambassador. I cannot tell you how deeply I appreciated it. It was a hearty welcome in returning to your country which has been for me a second home and it came from the American mining brotherhood which has been my second family.There are two distinct periods of learning in life. The first one are the years spent in school where we learn many things we after-wards forget; the second one are the years of prac-tical apprenticeship which engrave indelible signs in a man's character and shape his life. These latter years I spent in the United States and they have influenced the whole course of my life. I owe very much to my American friends who trained me. The earliest was Prof. Robert Peele, of Columbia University. At the Daly West mine, in Park City, Utah, he curbed my futuristic English spell-ing and had a hard time at it. Prof. James F. Kemp taught me that geology is a guess work just as unre-liable as the prediction of international events; he taught me also that a frank, honest and loyal character will lead a man equally straight through a mining report and through public life.

Jan 3, 1923

In late May, at its final session in Nairobi, Kenya, the UN Conference on Trade and Development (UNCTAD) narrowly rejected the US proposal for a new International Resources Bank suggested by Secretary of State Henry Kissinger. The proposal was defeated by a roll-call vote of 33 to 31, with most of the nay votes cast by communist countries, and with 89 of the less-developed countries abstaining or absent.

Jan 7, 1976

By D. C. McLean

This report summarizes the work that has been done during the past several years in adapting resins for use as auxiliaries in mine roof support. The resins were applied in two ways: 1) by injection into the strata, and 2) as a bonding agent for roof bolts and reinforcing bar. The Explosives and Mining Chemicals Department of the American Cyanamid Co. has worked during this period in cooperation with the Roof Control Research Group of the U.S. Bureau of Mines, the Pattin Manufacturing Co., the J. H. Fletcher Co., the Homestake Mining Co., the U.S. Steel Corp., the National Mines Corp. and the Pocahontas Land Corp. in an effort to create resin formulations and methods for applying them as a practical and sate type of roof support for mining areas particularly where conventional support is inadequate, yet expensive. This, work has involved much pioneering in a field where theory, speculation, and pure mythology predominates, and little basic engineering data is available. It is strange butt true that, despite the importance of roof control both from an operational and safely standpoint, there is scarcely a mining' company in this country that has an engineer, or anyone, assigned to the study of roof support problem, except temporarily--after a bad roof fall. The responsibility for improving roof control methods seems to have been placed entirely upon the shoulder, of the USBM, various State departments of mines, and individual roof bolt manufacturing; companies. It was in cooperation with the USBM that Cyanamid first developed resins for mining use.

Jan 1, 1964

By J. F. Kemp

PAGE Introductory Description of Deposits of this Type,.....244 Topography of the Ducktown Region,...247 Geology and Petrography,...248 The Mineralogy of the Ores and Gangue,..249 The older minerals : Amphibole, 250 ; Pyroxene, 250; Garnet, 251; Zoisite, 252; Calcite, 258 ; Quartz, 259 ; Apatite, 259 ; Rutile, 259. The Sulphides: Pyrite, 259; Zincblende, 259; Galena, 260; Pyrrho tite, 260; Chalcopyrite, 260. Later minerals, not belonging to the Gossan: Quartz, and certain sul phides, 261 ; Graphite, 261. The Formation of the Ore,...262 The Gossan Minerals,...........263 Bibliography,............265 Introductory Description of Deposits of this Type. Ore-bodies of more or less lenticular shape and lying parallel with the foliation of schists and slates form a group of

Jan 1, 1902

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Recent efforts to design drilling fluids for increased drifting rates have confirmed some laboratory results of other investigators, but have also produced additional data that should be considered. These data were obtained under controlled test conditions using a microbit drilling machine. Clays and some polymers have previously been reported to cause reduction in drilling rate. Recent data have shown that under laboratory conditions, suspensions of a single day or polymer have sometimes given faster drilling rates than when water was used. Measurements have been made of clay suspensions and polymer suspensions comparing filtration (I) under API conditions, (2) while drilling with temperature of 150F and differential pressure of 1,000 psi and (3) under dynamic conditions after drilling. Some correlation between instanraneous filtration (white drilling) and drilling rate has been observed. INTRODUCTION Several papers have been presented that related drilling fluids to penetration rate. Generally, it was found that a decrease in the solids concentration resulted in significant increases in the drilling rate. Of course, this change also resulted in a decrease in the viscosity of the drilling fluid.' Conclusions from investigations by this laboratory are in agreement. Data have shown that of the simple mud measurements commonly made at the drilling rig (density, plastic viscosity. yield point, API filtrate and total solids), only the density and total solids have a significant relationship to the drilling rate in Berea sandstone when attempting to correlate a single mud property individually.' More recent drilling rate experiments have been designed to study (1) effects of individual clays and polymers on drilling rates in Berea sandstone and Lueders limestone, (2) the relationship between drilling rate and dynamic filtration as measured after drilling and (3) the relationship between drilling rate and dynamic filtration as measured during drilling. Data show that drilling rates are dependent upon type and concentration of particles, type of formation and filtration of the individual fluids while drilling. Mud pressure: pressure of drilling fluid as measured after leaving the drilling chamber (Fig. 1). This is taken to be approximately the mud pressure just past the bit and at the face of the formation. Terrastatic pressure: pressure representing weight of overburden. Formation pressure: pressure of formation fluid as measured at outlet of drilling chamber (Fig. 1). This is taken to be approximately the pressure of fluid in the interstices of the formation. Differential pressure: difference between the mud pressure and formation pressure. LABORATORY EQUIPMENT AND TESTING PROCEDURE The drilling equipment was described in two previous publications."' Main components are a drilling chamber, filter-heater, rotary drive and variable-speed circulating pump. Auxiliary pumps supply pressure boosts for the mud, terrastatic and formation pressures. All equipment is designed for 15,000 psi and 500F. Capacity of the circulating system is approximately 7 gal. The mechanical design was facilitated by moving the rock down onto the bit. Data collected with this design should not differ from that obtained by a normal design where the bit moves into the rock. Drilling fluid is pumped through 50 ft of ID pipe coiled in an oil bath, enters the rotary shaft at a right angle and is pumped through the jets on the bit (Fig. 1). Most of the drilled solids are extracted by a screen mounted in the circulating system on the suction side of the pump. Data reported in this paper were obtained by controlling these parameters: mud pressure, 5,000 psi; formation pressure, 4,000 psi; terrastatic pressure, 5,000 psi; force on bit, 1,000 Ib; formation, Berea sandstone and Lueders limestone; flow rate, 7 gal/rnin; bit, 11/4-in. diameter with two 0.078-in jets; mud temperature. 150F; and rotary speed, 60 rpm. Mud pressure was controlled at 5,000 psi, thus giving a differential pressure of 1,000 psi even though the fluid densities varied. Cores of 3%;-in. diameter and 8 in. long were selected from quarry blocks to provide some control of grain size distribution, permeability and porosity. A 2-in. section was cut off each core and a I -in. diameter plug was taken from this section. Permeability to 5 percent by weight sodium chloride solution was determined and the large cores were

By Persifor Frazer

In his " Final Report," Vol. 11, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

By M. M. Singh

Coal mine operators are obligated to mitigate or plan for subsidence under the new regulations. This paper presents the types of subsidence control measures that may be employed to meet these requirements, which include: changes in mining methods, strata stabilization after coal extraction, construction of specially designed surface structures and foundations to accommodate ground movements, and comprehensive planning and coordination of surface land use with underground mining. The basic principles of these techniques, along with specific procedures that may be followed to implement them, are briefly discussed. Subsidence control methods that are currently being investigated are mentioned.

Jan 1, 1985

Jan 11, 1951

By O. U. Bradley

The methods of handling the oil output of the Mid-Continent fields are not unlike those practised in other oil fields of the United States, and it is not expected that this paper will present any entirely novel ideas. Some features of the practice of handling this oil may be of interest, however. Wooden Gaging Tanks Practically all of the oil sold to pipe line? and other purchasing agencies throughout the Mid-Continent field is gaged from wooden tanks. Steel gaging tanks are slowly coming into use, and are preferable in many ways—leakage and evaporation are reduced, and the strapping and recalculation of capacities are unnecessary. The wooden tanks are slightly coned to facilitate tightening the hoops. The sizes in common use are 250, 500, 800 and 1600 bbl. The number and the capacity of the gaging tanks upon any producing oil property depend upon its production, and the facilities for disposing of the output. The 1600-bbl. size was the most common in the Cushing field, particularly during the period of flush production. The tanks are distributed over the leased premises in groups of two, three, and four tanks each, and these are filled from flow tanks, or through direct pipe connections with the heads of the wells. Flow tanks are merely temporary reservoirs to facilitate the transfer of oil from the wells to the gaging tanks. They diminish fire risk, and are considered indispensable on small producing properties where water is pumped with the oil, as they permit the refuse and water to 'settle out before the production is run to the gaging tanks. strapping and Calculations After a gaging tank has been strapped (measured) and its contents computed, a deduction of 3 per cent. is made from its computed volume. The strapping of a tank requires four steps: (1) The outer circumferences

Jan 1, 1920

By Marcus Grossmann

THIS paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, 'the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of Chromium, Per Cent FIG. 1.-IRON-CARBON DIAGRAM. FIG. 2.-IRON-CHROMIUM DIAGRAM. alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron.

Jan 12, 1926

By D. J. Jr. McAdam

RESULTS of a general survey of corrosion-fatigue phenomena at the Naval Engineering Experiment Station were presented in five previous papers.1-5 In these papers references were given to the work of Haigh in 1917.6 The five papers mentioned gave a general survey of the behavior of metals when tested to failure under simultaneous corrosion and cyclic stress. As a result of this survey the fourth paper gave a tentative analysis of the corrosion-fatigue process. According to this analysis, if the initial stress is below the endurance limit but above the corrosion-fatigue limit, the corrosion-fatigue process is divided into two periods. The first period is the formation of pits. As the initial stress is below the endurance limit, the pitting is assumed to be due to corrosion, not to fatigue. The corrosion pitting, however, is not the ordinary pitting of stressless corrosion, but is an accelerated pitting due to the effect of the cyclic stress on the corrosion. As the pit progresses, both the actual stress and the effective solution pressure increase. The increase of actual stress is due to increasing stress concentration at the bottoms of the pits. The increase of effective solution pressure is due to the increase of actual stress. The mutual intensification of stress and solution pressure continues until the actual stress at the bottoms of the pits surpasses the endurance limit. The second period of corrosion-fatigue then begins. In this period the process is merely fatigue accelerated by the corrosion. The cracks advance at a continually accelerated rate until the specimen breaks.

Jan 1, 1930

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The ductile fracturing process was studied in single-crystal and poly cvystalline aluminum deformed in tension over a temperature range from 295° to 4.2°K. At temperatures as low as 77°K, the fracture of "inclusion-free" material, including zone-refined aluminum, was by rupture (-100 pct RA). At 4.2 OK, fracture was brought on by adia-batic shear. Metallographic examination did not disclose any voids or slip-band microcracks, thus negating for inherently ductile metals any mechanism of void nucleation by vacancy condensation or of cracking due to dislocation pile-ups. In Izigh-purity aluminum not treated to be inclusion-free, fracture at temperatures as low as 45°K was of the double-cup type and a result of void formation. The reduction-of-area decreased as temperature was lowered, corresponding to the earlier appearance of voids. Such behavior was rationalized in terms of a larger increase, with decreasing temperature, in the .flow stress relative to the strength of the inclusion-matrix interface. Evidence for low-temperature adiabatic shear was found in discontinuous flow at 4.2"K, in the transition to a localized shear fracture at low temperatures, and in the suppression of shear fracture with an elastically hard pulling device. A simple analysis for the initiation of adiabatic shew permitted a general correlation of the various contributing factors. It has been pointed out that the duration of shear depends upon effective mass and elastic stiffness of the deformation system. IT has long been recognized that fracture* may Throughout this paper, the term "fracture" is taken to mean any process that results in the separation of a material into two (or more) parts. Thus rupture as it may be encountered in a tension test leading to 100 pct reduction-of-area is included in this category. occur in a ductile mode, and that the process can be of great practical as well as general interest. Much information about ductile fracture has also been accumulated over this period, but only recently has an understanding of mechanism begun to appear. Ludwik,' in 1926, first reported fracture in a tensile specimen starting with a central crack in the necked section. Since then, other studies have disclosed that such cracks may form by the coalescence of voids nucleated in this region where hydrostatic tension is highest.2-4 Rogers and Crussard et al.' have emphasized void formation and reori-entation along localized shear bands as a mode of crack propagation. pines6 has considered the tensile rod as a bundle of fibers joined by weak interfaces, which subsequently separate to allow individual fiber contraction. The notion of cavity growth and coalescence by purely plastic processes was discussed by Cottrell: who added that the tensile reduction-of-area ought not to be sensitive to temperature. On the other hand, it has been observed that the reduction-of-area is greatly increased if tests are carried out at high temperaturesa or under high hydrostatic pressure.' Fracturing anisotropy in wrought products lends support to the idea of void formation from preexisting flaws strongly aligned by earlier processing.''-l2 There is evidence that many voids result from the fracturing of inclusions or separation at the inclusion-matrix interface Another possibility is that voids grow out of pore volume produced in the initial solidification and never fully removed in later working. In general, a structure 3f particles, pores, and weak interfaces can be expected, at least in materials of engineering interest. Vacancy condensation has been suggested as an alternative mechanism of void formation for materials considered to be inclusion-free.13 Yet experience has shown that tensile reduction-of-area increases with purity, to the extreme of rupture as so often observed in single crystals. Adiabatic shear has an important bearing on ductile fracture. It occurs when the decrease of flow stress, as a result of local temperature rise from heat generated during straining, becomes larger than the increase due to strain and strain-rate hardening. As demonstrated by experiments on punching of plates,14 a large temperature rise may be brought about by rapid straining. Adiabatic flow as a result of the high strain rate reached in an ordinary tensile specimen just prior to separation may account for the cone formation in cup-and-cone fracture;14 evidence of such local heating has been presented.15 For geometrical reasons, however, pure sliding along the conical surfaces is unlikely, and separation under tensile forces is probably an important accompanying feature of the shear.7 In deformation processing operations, a high shear-strain rate may exist at boundaries between plas-

Jan 1, 1964

By R. V. Norris

THE wage rates and working conditions in the anthracite. region of Pennsylvania have been governed for nearly 20 years by the award of the Anthracite Coal Strike Commission, appointed Oct. 16, 1902, by President Roosevelt. The report of this com-mission, made in March, 1903, was accepted and, with eight modifications made at various dates, has had .almost the force of law, and has kept this great indus-trial region free from strikes for almost a generation. In 1920, President Wilson appointed an Anthracite Coal Commission, and its report, accepted Aug. 30, 1920, governed wage conditions to April 1, 1922. Actually, the agreements have been for terms of two to four years, and lately, in 1916 and 1920, the employ-ees have continued at work pending the negotiation of new agreements which were made retroactive, and which have all been modifications of the original 1903 award. With the expiration, April 1, 1922, of the 1920 award approaching, Mr. Lewis, president, of the United Mine Workers of America, addressed a letter, on Feb. 20, to the operators, suggesting a meeting on March 15; this date was accepted by the latter, with the notation that the time was short. At the meeting, the Mine Workers presented 19 demands, and advised that if a satisfactory agreement was not reached by April 1.a suspension of mining would occur, contrary to the practice since 1916 of continuing work with a retro-active adjustment.

Jan 6, 1922

By Allen D. Garrison

THE chemistry of clays and shales has been assuming increasing importance in the petroleum industry, and two factors have greatly influenced this trend. The first has been the growing evidence that the marine shales are source beds, and that the petroleum compounds have migrated to the sand reservoirs overlying or underlying these shales: the second has been the demand for drilling fluids better adapted to penetrate these marine shales without difficulty and expense. ORIGIN AND GENERAL COMPOSITON OF CLAYS AND SHALES Clays, shales and surface soils are all closely related materials. They are mixtures of finely divided compounds formed during the weathering of the solid crust of the earth. Their nature is essentially colloidal; that is, their behavior is determined by the state of division of the materials and the surface reactions of the smallest grains. Many of their chemical changes affect only the exposed areas and do not involve the interior of the grains of matter. The extent of these reactions is more nearly proportional to the area of the substances than to their mass, therefore it is possible for a small amount of a material in an extremely fine state of division to completely dominate the character of the mixture. More than 83 per cent of the crust of the earth is composed of three elements-oxygen, silicon and aluminum. Consequently, the corrosion products of the crust are predominantly aluminosilicates, or compounds of aluminum, silicon and oxygen. If we add the compounds of six elements-iron, calcium, sodium, potassium, magnesium and hydrogen-more than 98 per cent of the crust has been accounted for. These six elements, together with the first three, also appear in soils, clays and shales. But direct chemical analysis is of little value in describing the nature of such materials. Many chemical individuals may be present in variable amounts, and the extreme subdivision of any one of the individuals may contribute qualities that dominate the mixture.

Jan 1, 1939

Mills Day left a journal of his travel to Ohio and return by way of Pittsburgh in 1810. He left this comment about western Pennsylvania: "June 19. As I proceeded toward Pittsburg, (From Washington and Canonsburg) the country grew more populous. The hills appeared to consist of strata of freestone, iron, coal, and slate. June 20. Its (Pittsburg's) water communication with a vast extent of country and the immense beds of coal in its immediate vicinity render it a place peculiarly adapted to manufactures. Coal may be obtained of a good quality, ready delivered at 5 cents a bushel."1 Until within a year or so of this period, coal was used for domestic purposes, brick-making, by blacksmiths, etc.; now the industry entered a period of rapid growth caused by the introduction of the steam engine. As manufacturing was increasing due to the settlement of the western country, the additional facilities created by mechanical power were welcome. Apparently the first engine was installed in Pittsburgh, in a steam grist mill, in 1808; it is described in the Navigator of 1811: "The water of the boilers are heated by large fires made of stone coal, which is introduced at one end into a grated fire place as long as the cylinders themselves; the quantity of coal consumed daily by these boilers is said to be about twenty bushels, which cost one dollar." Later it mentions the effect of burning coal:

Jan 1, 1942

By G. D. Cody, D. S. Beers, B. Abeles

The thermal diffusivity (thermal conductivity divided by specific heat) of Armco iron has been measured over the temperature range 30º to 1025ºC. The results are in good agreement with the thermal diffusivity computed from published values of thermal conductivity and specific heat, except near the Curie point and at the a to y phase transition, where the measured diffusivity undergoes rabid variations. The differences observed are ascribed to a rapid variation in the electronic thermal conductivity near the Curie point, and a decrease in the lattice thermal conductivity, at the a to ? phase transition. A major difficulty in measuring the thermal conductivity of materials at high temperatures is the determination and elimination of radiation losses. It has been shown, however, that in measuring thermal diffusivity D (thermal conductivity/specific heat) radiation losses can be taken into account exactly.' In order to test the performance of a newly designed apparatus for measuring thermal diffusivity of solids,' we measured Armco iron to an accuracy of 2 pct in the temperature range 30" to 1025°C. This material was selected since both the thermal conductivity,3'4 k, and specific heat,5 C, are known accurately in this temperature range and thus the measured values of D could be compared with D computed from the pub-

Jan 1, 1962