Search Documents

By T. L. Joseph

THE committee appointed to investigate the application of oxygenated air to the blast' furnace believes, after a careful study of the problem, that this enriched air will increase hearth temperature, tonnage, flexibility of operation, and quality of pig iron made, and that fuel consumption will be decreased. These improvements are supported by theoretical evidence; but a practical trial of the process is necessary to establish more definitely the magnitude of benefits realized. The commercial application, however, may profitably be preceded by a test on a smaller scale. A small furnace will, in general, respond to the enriched air in the same way as a commercial furnace and the magnitude of the benefits to be gained from varying additions of oxygen can be fairly well established at relatively little expense. A new experimental furnace, being built jointly by the Bureau of Mines and the University of Minnesota, at Minneapolis, will have a capacity of about 6 tons and will riot require more than 700 cu. ft. of natural air per minute. Its hearth is 36 in. in diameter and its height about 32 ft. Enough oxygen to enrich the blast to the extent recommended by the committee can be obtained from a small oxygen unit. It might even be cheaper to perform preliminary experiments with tanks of oxygen obtained from regular, dealers. A procedure in making the test that suggests itself is to start with operation on normal air; then to use blast, enriched in several steps. Systematic temperature measurements of the tuyeres, slag, and metal would reveal any changes in hearth temperature. When these changes become large enough, the burden may be gradually increased to just within the breaking point and the furnace brought back to normal, if possible, by the addition of oxygen. Such a test would show what might be expected in the way of a decrease in fuel consumption and the time taken to "straighten up" the furnace by means of oxygen. The new furnace at Minneapolis is so equipped that the furnace process can be observed from the stock line to the iron notch. We have been taking gas samples at various elevations in the furnace to study combustibility of the fuel and the reducing power of the gas. If either of these is affected by removing inert nitrogen, the change can easily be measured.

Jan 11, 1924

By R. C. Patterson

IN view of the circumstance that very few important changes have been made within the last 15 or 20 years in the equipment of rod and wire mills, the description of a new process introduced by Grenville Mellen, of Llewellyn Park, N. J., to take the place of the present laborious system of producing rods of lead, zinc, brass, copper, aluminum, etc., may be interesting to members of the Institute. This new process consists in the production of cast rods at one operation in a small continuous casting machine. The hot liquid metal is transferred from the melting crucibles directly into an endless chain of mold blocks in the machine, where solidification takes place, and the rod comes out continuously in a solid form at one end as long as the molten metal is supplied. The operation of these mold blocks so as to produce a solid rod of uniform structure constitutes an important part of Mr. Mellen's invention. The machine (Figs. 1 and 2), 12 ft. in height over all, 2 by 3 ft. in horizontal- cross-sectional area, and 6,000 11). in weight, has a framework of cast iron, holding in position two endless chains of mold blocks, which are made in sections and join in center alignment. The mold orifice is made up of these mold sections, into which the liquid metal flows. The molding chains are composed of steel blocks, grooved on one face to form the molding cavity, and linked together with flexible joints. Each block is carried on four rollers which guide the chain around the end sprockets and carry it in its course through the machine. The accuracy of alignment requisite to the production of a perfect rod in the mold groove formed by these sections is secured by careful machine work, and by building the four ways, down which the alignment takes place, so that two of the sides are fixed permanently, while the opposite sides are held to their position by spring pressure. The guides carrying the molds, while in casting position, are water-cooled square tubes.

Jan 5, 1915

By Paul Weir

During the past decade, methods of producing bituminous coal in the state of Illinois, which ranks third in production among the states in which bituminous coal is mined, have undergone great changes. From less than one million tons in 1923, the strip-mine production has gradually increased to a high of 11,725,870 tons in 1937. From a negligible amount prior to 1927, the amount of coal mechanically loaded underground had increased to a high of 28,374,362 tons in 1937. The amount manually loaded in 1937 reached a low of 12,332,023 tons. In this same year, this state ranked first in strip-mine production, also in mechanically loaded production. For this reason a study of the influence of mechanization on location of production in Illinois may be helpful in anticipating what may happen in other producing states. The reason for the changes in methods lies in the differences in costs of production. The Bureau of Research and Statistics of the National Bituminous Coal Commission has made public the following costs of production by various methods in the state of Illinois (district 10) for the last nine months of 1937: all mines, $1.7602 per ton; strip mines, $1.4319; mechanical loading mines, $1.7457; hand loading mines, $2.1793; all underground mines, $1.8703. These are weighted averages for the entire district. Inasmuch as production in 1937 was reported from 58 counties scattered over two-thirds of the area of the state and from five different seams varying in thickness from less than 3 ft. to as much as 12 ft., it is apparent that the location of production must be influenced by the extent of mechanization possible in the various producing counties. SHIFT in Production The term "mechanization" is commonly used to designate the coal-loading operation. However, in a broader sense it embraces the use of any and all mechanical and electrical equipment on the surface and underground. Strip mining is an intensive form of mechanization. The mechanical cleaning of coal is a form of mechanization. Cutting machines and motor haulage likewise are forms of mechanization, hence

Jan 1, 1940

By Paul Weir

During the past decade, methods of producing bituminous coal in the state of Illinois, which ranks third in production among the states in which bituminous coal is mined, have undergone great changes. From less than one million tons in 1923, the strip-mine production has gradually increased to a high of 11,725,870 tons in 1937. From a negligible amount prior to 1927, the amount of coal mechanically loaded underground had increased to a high of 28,374,362 tons in 1937. The amount manually loaded in 1937 reached a low of 12,332,023 tons. In this same year, this state ranked first in strip-mine production, also in mechanically loaded production. For this reason a study of the influence of mechanization on location of production in Illinois may be helpful in anticipating what may happen in other producing states. The reason for the changes in methods lies in the differences in costs of production. The Bureau of Research and Statistics of the National Bituminous Coal Commission has made public the following costs of production by various methods in the state of Illinois (district 10) for the last nine months of 1937: all mines, $1.7602 per ton; strip mines, $1.4319; mechanical loading mines, $1.7457; hand loading mines, $2.1793; all underground mines, $1.8703. These are weighted averages for the entire district. Inasmuch as production in 1937 was reported from 58 counties scattered over two-thirds of the area of the state and from five different seams varying in thickness from less than 3 ft. to as much as 12 ft., it is apparent that the location of production must be influenced by the extent of mechanization possible in the various producing counties. SHIFT in Production The term "mechanization" is commonly used to designate the coal-loading operation. However, in a broader sense it embraces the use of any and all mechanical and electrical equipment on the surface and underground. Strip mining is an intensive form of mechanization. The mechanical cleaning of coal is a form of mechanization. Cutting machines and motor haulage likewise are forms of mechanization, hence

Jan 1, 1940

By Arthur Braid

The war has caused an increasing scarcity of phosphorus and its well known alloys with copper and tin. At the same time, the production of brass and bronze, nickel-silver, cupro-nickel, and other non-ferrous alloys, has considerably increased. The manufacturers of these products had therefore to secure other materials which would serve their purpose; principally that of a deoxidizer, which could be obtained promptly and regularly. Fortunately these materials, pure carbon-free manganese metal and manganese-copper alloy, were not hard to find—in fact, they were never lost. Manganese in various forms has been used in Europe for more than a century; in this country, however, when manganese was first used, and indeed for a long time thereafter, it was consumed mainly in the manufacture of manganese-bronze. Many foundrymen at that time used manganese-copper with the same freedom as phosphor-copper. Although iron enters into the composition of certain grades of bronze, it is very detrimental to non-ferrous mixtures in general; consequently ferromanganese is not applicable, and therefore pure manganese metal, or the alloy of manganese and copper, technically free from iron and other impurities, is now being generally used. The following are the principal elements having an affinity for oxygen: 1, Sodium. 2, Potassium. 3, Calcium. 4, Strontium. 5, Barium. 6, Magnesium. 7, Aluminum, 8, Phosphorus. 9, Silicon. 10, Manganese. 11, Iron. 12, Zinc. 13, Lead. Each metal has its natural flux, or deoxidizer, in the form of a metal or non-metal which will alloy with it, and has a strong affinity for oxygen. For example, phosphorus, as is well known, acts very beneficially in copper alloys that contain tin. Within the last few years, and particularly since the war began, the .great value of mangancse in nickel alloys has been demonstrated, and one by one the manufacturers of these products have adopted its use. While manganese has not so strong an affinity for oxygen as magnesium, aluminum, or silicon, it is nevertheless sufficiently powerful to reduce any oxide of nickel, copper, or zinc that may be present in the nickel alloy to be purified.

Jan 1, 1919

By Clyde Longyear

DURING the last two years, the diamond core drill has come rapidly to the front as a very valuable auxiliary to the equipment of the exploration and production departments of oil companies. The diamond drill and the rotary oil drill work on the same general principles, the essential difference being that the diamond drill employs an annular steel bit set with black diamonds ("carbons"), instead of the fish-tail or other type of bit employed by the rotary drill. On account of the brittleness of the carbon and the danger of breakage if subjected to sudden blows or stresses, it is not practicable to attach a diamond bit and core-barrel to the end of a rotary drill stem. The operating mechanism of the diamond drill must be subject to much more sensitive control than the rotary drill. The bit must be rotated smoothly, without the jerks that are incident to the operation of the clutches and chain drives on the rotary draw works, and the feed must be con-trolled in a much more delicate manner than the mere action of a brake on a hoist. To accomplish this smooth rotation, diamond drills are usually built as a self-con-tained unit with the crank shaft of the engine geared direct to the drive shaft that turns the drill rods or stem. One or two hydraulic cylinders connected with a high-pressure pump control the feed so definitely that the bit can be raised or lowered at will, while the bit is rotating, by the simple operation of valves. The smaller-sized-drills for very shallow work usually have a screw feed control instead of the hydraulic feed. The principal uses of the diamond drill in oil work are three: 1. Reconnaissance or structure drilling; that is, the drilling of a number of shallow holes to ascertain the subsurface contour. 2. Scout drilling, or the drilling of holes of smaller diameter than is required for production, to obtain information as to the character of the oil sand and the quality of the oil. 3. Drilling producing wells.

Jan 5, 1923

By Arthur Braid

THE war has caused an increasing scarcity of phosphorus and its well known alloys with copper and tin. At the same time, the production of brass and bronze, nickel-silver, cupro-nickel, and other non-ferrous alloys, has considerably increased. The manufacturers of these products had therefore to secure other materials which would serve their purpose; principally that of a deoxidizer, which could be. obtained promptly and regularly. Fortunately these materials, pure carbon-free manganese metal and manganese-copper alloy, were not hard to find-in fact, they were never lost. Manganese in various forms has been used in Europe for more than a century; in this country, however, when manganese was first used, and indeed for a long time thereafter, it was consumed mainly in the- manufacture of manganese-bronze. Many foundrymen at that time used manganese-copper with the same freedom as phosphor-copper. Although iron enters into the composition of certain- grades of bronze, it is very detrimental to non-ferrous mixtures in general; consequently ferro-manganese is not applicable, and therefore pure manganese metal, or the alloy of manganese and copper, technically free from iron and other impurities, is now being generally used. The following are the principal elements having an affinity for oxygen: 1, Sodium. 2, Potassium. 3, Calcium. 4, Strontium. 5, Barium. 6, Magnesium. 7, Aluminum, 8, Phosphorus. 9, Silicon. 10, Manganese. 11, Iron. 12, Zinc. 13, Lead. Each metal has its natural flux, or deoxidizer, in the form of a metal or non-metal which will alloy with it, and has a strong affinity for oxygen. For example, phosphorus, as is well known, acts very beneficially in copper alloys that contain tin. Within 'the last few years, and particularly since the war began, the great value of manganese in nickel alloys has been demonstrated, and one by one the manufacturers of these products have adopted its use. While manganese has not so strong an affinity for oxygen as magnesium, aluminum, or silicon, it is nevertheless sufficiently powerful to reduce any oxide of nickel, copper, or zinc that may be present in the nickel alloy to be purified.

Jan 11, 1918

By Richard H. Zinszer

Application Of electric logs has been used in correlation of subsurface structure to determine the size and shape of the oil reservoir. Such a knowledge is hardly complete until saturation and productivity are determined for the various horizons. It is difficult to use electric logs successfully for this purpose because of the many factors that influence the curves. In this work an effort was made to establish an empirical correlation between formation resistivity for a series of electric-log curves and water saturation and oil productivity of sand. Electric logs were obtained by recording with 10 different electrode spacings through the same interval of a well. In the analysis of these curves all factors except two, a dependent and independent variable, were held constant. The interval studied had been cored and a large number of samples were analyzed in the core laboratory in order to compare the values of permeability and saturation with the measured values of formation resistivity. Results of this analysis indicate: (I) the depth to which mud filtrate enters a sand body, (2) a correlation between permeability and sand resistivity for shallow penetration depths, and (3) that the water saturation for an oil sand can be determined from the measured sand resistivity after making suitable corrections for sand thickness. The procedure in the last method depends on a correction for thickness factor and a theoretical curve. The accuracy of the theoretical curve is now being tested in the laboratory Introduction In an effort to place the analysis of electric logs on a quantitative basis, there is need for a better understanding of the many factors that influence an electric-log curve. These factors may be large differences in sand thickness, permeability of the sand, salinity of the interstitial water, mud resistivity, formation temperature, and other sources. A number of examples were presented by Archie,' which treat the effect of sand thickness on measured resistivity. He compared the true resistivity of a sand with the observed resistivity for sands 8 it., 16 ft., and 24 ft. thick, and found the observed resistivity of the 8-ft. sand to be approximately

Jan 1, 1946

By Richard H. Zinszer

Application Of electric logs has been used in correlation of subsurface structure to determine the size and shape of the oil reservoir. Such a knowledge is hardly complete until saturation and productivity are determined for the various horizons. It is difficult to use electric logs successfully for this purpose because of the many factors that influence the curves. In this work an effort was made to establish an empirical correlation between formation resistivity for a series of electric-log curves and water saturation and oil productivity of sand. Electric logs were obtained by recording with 10 different electrode spacings through the same interval of a well. In the analysis of these curves all factors except two, a dependent and independent variable, were held constant. The interval studied had been cored and a large number of samples were analyzed in the core laboratory in order to compare the values of permeability and saturation with the measured values of formation resistivity. Results of this analysis indicate: (I) the depth to which mud filtrate enters a sand body, (2) a correlation between permeability and sand resistivity for shallow penetration depths, and (3) that the water saturation for an oil sand can be determined from the measured sand resistivity after making suitable corrections for sand thickness. The procedure in the last method depends on a correction for thickness factor and a theoretical curve. The accuracy of the theoretical curve is now being tested in the laboratory Introduction In an effort to place the analysis of electric logs on a quantitative basis, there is need for a better understanding of the many factors that influence an electric-log curve. These factors may be large differences in sand thickness, permeability of the sand, salinity of the interstitial water, mud resistivity, formation temperature, and other sources. A number of examples were presented by Archie,' which treat the effect of sand thickness on measured resistivity. He compared the true resistivity of a sand with the observed resistivity for sands 8 it., 16 ft., and 24 ft. thick, and found the observed resistivity of the 8-ft. sand to be approximately

Jan 1, 1946

By N. H. MacMillan, O. C. Dias

Recent work by Westwood et al. (reviewed in Refs. 1-6) has established that many rocks, minerals, ceramics, and glasses exhibit phenomenologically similar chemomechanical (Rebinder) effects when deformed in different liquid environments, apparently as the result of chemisorption-induced variations in their near-surface flow and flow-dependent fracture behavior. In particular, it appears that there exists an empirical, but apparently general, correlation between the near-surface flow stress of an inorganic nonmetal and its surface charge- namely, that such a solid is hardest at its zero point of charge (i.e., when its zeta potential [ ] = 0) and softens as [ ] increases, regardless of the sign of zeta. Moreover, because near-surface flow and fracture phenomena are two of the important determinants of the rates of machining and comminution processes, both Westwood et al. and others7 have been able to use this so-called "[ ]-correlation" to develop cutting fluids and grinding aids that in many instances have given rise to several fold increases in performance. In addition, Westwood et al. have demonstrated that both aqueous and organic environments can give rise to similar improvements in cutting rate for a given combination of tool and workpiece, provided that both impart the same surface charge to the work- piece (i.e., transfer the same number of electrons to or from its surface). This last finding implies that in any application it should always be possible to find some cutting fluid that is at once effective, cheap, nontoxic, and nonpolluting. Thus, reports of apparently similar environmental influences on the mechanical behavior of diamond,8 certain organic crystals and polymers,9-14 and coa1-15-21 suggest that it is pertinent to ask: (a) whether the [ ]-correlation (or any analogous relationship) extends to coal; and (b), if so, whether this relationship can be used to guide the development of superior aids for grinding coal. Accordingly, correlations have been sought between (1) the zeta potentials, (2) the hardnesses, and (3 and 4) the drilling and grinding characteristics of coals of different rank in different aqueous and organic environments. This paper reports the results of that search.

Jan 1, 1980

By J. M. Callow

The selective action of oils for lustrous minerals was first disclosed by Haynes in 1860. In 1885, Miss Carrie Everson elaborated this idea and also disclosed the fact that acid increased the so-called selective action. Her patent called for oils, either animal, vegetal or mineral, also for an acid or salt. The process was tried out on a practical scale in Baker City and Leadville, in 1889, and failed: first, because, as has since been shown, of the unsuitability of the ore to flotation; and second, because the invention was too far in advance of the times. Then followed the Elmore brothers, first with their bulk oil processes and later with their vacuum method. The basic principles of oil flotation were undoubtedly covered by the above inventors, the work done since their time being merely a building up on ground work laid by them. Different kinds of oil, different quantities of oil, and all the varying degrees of agitation, were all exemplified and practiced by them in one phase or another, and the developments that have since been made are but elaborations of the fundamental principles laid down by Haynes, Everson, and the Elmore brothers. In 1902, the Potter-Delprat process was developed in Australia. In this process no oil was used, the mineral being raised by the generation of gas, brought about by the introduction of acid into the pulp. The mineral particles appeared on the surface of the separatory vessel, in the form of a scum or froth, buoyed up by minute gas bubbles attached to them. This no doubt first gave the suggestion of gaseous flotation. In 1902, also, Froment, an Italian, was granted a patent in which he combined violent agitation with oil and gaseous flotation, the gas being generated within the pulp, in much the same way as in the Potter-Delprat process. In the same year, Cattermole came out with a unique method. First, the pulp was emulsified with a small quantity of oil, by violent

Jan 1, 1916

By Fred E. Wright

In a recent paper1 a detailed discussion is given of the possibilities of using polarized light in the examination of opaque substances. The factors underlying the problem are there treated from the viewpoint of the electromagnetic theory of light and the presentation is necessarily mathematical in form. The practical methods resulting from the discussion are, however, relatively simple and promise to be of value in the determination of certain ores and metals when studied in reflected light under the microscope. The results of the theoretical investigation referred to may be summarized by stating that in general the optical constants, such as refractive indices and absorption indices, cannot be satisfactorily ascertained on small, random, polished sections; that the use of polarized light enables the observer ordinarily to determine whether the crystal plate is iso-tropic or anisotropic, and also to ascertain the degree of anisotropism; that for this purpose methods based either on the contrast in intensity between the two reflected components of non-polarized light, or on the amount of rotation of the plane of polarization, on reflection, of vertically incident, plane-polarized light, may be employed; that methods based on the phase difference between the two reflected components are in general of little value because of the small differences in phase which ordinarily result for a relatively large change in birefringence or biabsorption. The measurement of the optical properties of transparent minerals, even in minute irregular grains, is a simple task with modern petrographic microscope methods and is accomplished by petrologists as part of their ordinary routine work. But the determination of the optical constants of opaque substances is difficult and is rarely attempted; all observations are necessarily made in reflected light and are restricted commonly to the determination of color, of hardness, of the character of crystallization, and of the behavior of the mineral or metal plate toward reagents and abrasives. With practice, the observer becomes expert in recognizing details of this kind and determines with a high degree of certainty the different

Jan 1, 1920

By J. Ruben Velasco, Roland B. Mulchay

CANANEA has long been recognized as a remarkable field for geologic study. The copper deposits and rocks of the district have been described by many geologists and engineers, but only the most general correlations have been made between Can-anea sedimentary rocks and other known sedimentary sections in the southwestern United States and northern Mexico. The present paper describes the Cananea sediments in greater detail than has been done before and attempts to fit the Cananea sedimentary section more closely into the geologic time table. The lack of well-preserved fossils has made it difficult to date the sediments accurately in geologic time, but it is possible to make tentative correlations between the Cananea sediments and the southeastern Arizona sections, based largely upon lithology and general position in the geologic column. It appears that sedimentation at Cananea and Bisbee may have been closely similar during Paleozoic time. Even such generalized correlations, however, may be subject to considerable modification in the future. The present study has led to the recognition of other problems of age and mineralization relationships in the Cananea district. Cananea is located in the north-central part of the state of Sonora, Mexico, at an elevation of 5270 ft. It is about 135 miles northeast of Hermosillo, the state capital, and 25 miles south of the international boundary. By road Cananea is 40 miles from the twin towns of Naco, Ariz., and Naco, Sonora, and about 50 miles from Bisbee, Ariz. It is served by the Nogales-Naco branch of the railroad, F.C. Pacifico, and is connected with Chihuahua and Mexico City by the Aeronaves airline. The headwaters of three rivers flowing to the Gulf of California are located in the Cananea Mountains: the San Pedro River, flowing to the north; the Sonora River, flowing south and west; and the Mag-dalena River, flowing west. Elenita Mountain, the highest point in the district, has an elevation of 8140 ft. The Cananea Mountains extend in a series of north-south to northwest-southeast spurs and ridges and are surrounded by gently sloping gravel plains. The mineralized area, lying across the southern and central parts of the range, is about 6 miles long and at most 2 miles wide. Elevations at the mines vary from 5300 ft at Cananea-Duluth mine at the southeast end of the district to between 6000 and 7000 ft at the west end of the mineralized area at Puertecitos-Elenita mines. Principal production has been from the intensely mineralized and altered area of Capote Basin in the central part of the district and the immediately surrounding area to the southeast. The district has produced over 2 billion lb of copper, substantial molybdenum, and minor amounts of lead, zinc, silver, and gold. Total production through 1949 is estimated at more than $300 million. In 1900 large-scale development was started at Cananea by W. C. Greene. Until World War II only high-grade ores were exploited; low-grade ores were extracted after the installation of a large concentrator in the early 1940's, and subsequent operations have been based upon mining and processing ores containing less than 1.0 pct copper from open-pit and underground workings. Mining and concentration of such low-grade ores, however, are made possible only by continued high copper prices, and active exploration for high-grade orebodies has been continued throughout the important mineralized areas. General Geology Study of the involved rock pattern at Cananea has indicated a complex geologic history for the district. Widespread alteration and mineralization have masked many of the salient features and have led to widely varying geologic interpretations over the years. Further work will probably disclose new information which will modify current beliefs. At Cananea a conformable series of sediments of probable Paleozoic age was deposited on an unknown basement. Following Paleozoic time there was an extended period of erosion common to many districts in the southwestern U. S., and there is no present evidence of marine sedimentation at Cananea after the Paleozoic. The eroded surface was eventually covered with a great thickness of extrusive volcanic rocks. The entire series of sediments and volcanic rocks was later intruded by a variety of deep-seated igneous rocks. These included the Cananea granite, the Cuitaca granodiorite, the El Torre syenite, the Tinaja diorite, the Campana diabase and gabbro and the Colorada rhyolite quartz porphyry. Faulting of early age, probably prior to the deposition of the volcanic rocks, may have been responsible for the present position of some of the intrusive rock masses. In the Capote mine on the third and fourth levels the northwest-striking Rick-etts fault zone, with apparent offset of about 800 ft, has been sealed by a dike-like mass of Cananea granite which gradually increases in size with depth. In lower levels of the mine the granite forms a large southeast-plunging mass generally following the course of the Ricketts zone. The granite is not known southeast of the Capote-Oversight mine areas and the Ricketts fault does not appear in the vol-canic~ southeast of Capote Basin, but several plugs of Colorada quartz porphyry cut the volcanics along the assumed general southeast trend of the Ricketts zone. These porphyritic intrusives may be the up-

Jan 1, 1955

MONTANA SECTION W. C. SIDERFIN, Chairman, OSCAR ROHN, Vice-Chairman, E. B. YOUNG, Secretary-Treasurer, 526, Hennesey Building, Butte, Mont. F. W. BACORN, C. D. DEMOND. The semi-annual meeting of the Montana Section was held at the Silver Bow Club, Butte, Montana, on Friday, Nov. 16, at 8 p. m.; this was a postponement of the regular October meeting because of conflict in date with the St. Louis meeting of the Institute. An informal dinner was served to 68 members and guests. After dinner, Chairman W. C. Siderfin called the meeting to order. The minutes of the annual meeting, of Feb. 2, 1917, and the special meeting of May 21, 1917, were read and approved. C. W. Goodale led the discussion with "Notes on the St. Louis Meeting." He was followed by J. H. Warner who spoke on " The Joplin and Miami Districts," and by J. L: Bruce, Alexander Leggatt, N. B. Braly, and E. B. Young, the latter speaking on the work of the War Minerals Committee; and on the Cosden Oil Refinery at West Tuba, Okla. R. H. Sales reviewed briefly the manganese situation. E. N. Norris presented a paper on "Fire Proofing of Mine Shafts by the Anaconda Copper Mining Co." This resulted in interesting discussion by C. L. Berrien, C. E. Nighman, N. B. Braly, W. B. Daly, B. H. Dunshee, and J. J. Carrigan. C. L. Berrien and C. E. Nighman presented their papers on "Fire Extinction by Hydraulic Filling." In view of the late hour, discussion was waived. The executive committee, by unanimous consent, decided to request written discussion of the above papers to be presented at the next meeting, in February. B. B. Thayer spoke interestingly on the work of the Naval Consulting Board, and referred to the arsenic situation. Spencer Miller, also a, member of the Naval Consulting Board, entertained the-meeting with a vivid description of the method of "Coaling Battleships at Sea." Robert Sticht of Tasmania, in a short talk, spoke feelingly of his relations with the United States. At a late hour adjournment ended a most successful and interesting meeting. E. B. YOUNG, Secretary.

Jan 1, 1918

By Albert Mendelsohn, Charles F. Jackson

The system of stoping described in this paper was first introduced at the Champion mine of the Copper Range Co., Painesdale, Mich., in 1929, and since that time has been developed to a high state of efficiency. The method was devised to overcome some of the objections to the system of horizontal cut-and-fill stoping formerly employed at this mine and has done so successfully. The objections to the old system became more pronounced as the depth of mining operations increased and a change became a matter of necessity. While the combination of conditions encountered at the Champion mine is rather unusual, it is believed that the sublevel system developed there could be employed advantageously at other mines, though certain modifications might be necessary. This paper describes the method and the results obtained through its use, and suggests modifications for making it applicable under quite different conditions from those at the Champion mine. Champion Lode The lode being mined at the Champion mine is the heavily brecciated top of what is known in the district as the Baltic lava flow. The brecciated portion of the lode varies from 6 to 50 ft. in width. Under this breccia is the thinner, tighter, amygdular portion of the lode; under the amygdular portion is the trap footwall. Native copper is found deposited in the rock fragments of the breccia, in the cementing material of the breccia, in the amygdules and in the trappy rock under the amygdular part of the lode. In some places masses of copper many tons in weight extend far into the footwall of the lode. The Baltic lode on Champion property is 8000 ft. long, very straight along the strike, and dips uniformly 70' to the west for 3000 ft. in depth, at which point the dip begins to flatten slightly. The width of the copper-bearing portion of the lode varies from 10 ft. to as much as 80 ft. in a few places; the average width now mined is 17 ft. The lode rock is hard—the standard one-man drilling machines used in the mine drill from 10 to 14 in. per minute when mass copper is not

Jan 1, 1932

By Portland P. Fox, Berlen C. Moneymaker

The development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. The Equipment The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1941

By Portland P. Fox, Berlen C. Moneymaker

The development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. The Equipment The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1941

By A. A. Brant

In this presentation, concepts of the formation and evolution of the universe, the earth, and the cyclic civilizations of man are broadly outlined. The 5 billion or more years of the universe and the 4% billion years of the earth are contrasted to the 5000 years of modern society and the 100 years of objective scientific breakthrough. THE UNIVERSE Let us start back as far as possible, to the beginnings of this universe, some 5 billion or more years ago. This is a time interval that can be crudely underestimated by the moon-earth tidal friction effects that have increased the length of the day by about 1/1000 second per century — from a 5 to 7 hour day to its present 24 — and have moved the moon away at 5 inches per year to its present 240,000 miles. The oldest stony meteorites from interplanetary space give an age dating of some 4.6 billion years, approximating the time of formation of our earth. Further, certain stars pulsate, the period of pulsation being related to their absolute brightness. Measuring apparent brightness and comparing, gives the distance away. Thus Hubble and Shapley of Harvard, from 1925 on, were able to show that the universe reached as far as our telescopes could scan. The Doppler shift of the hydrogen red lines could only mean that the nebulae, or galaxies, were moving away away at velocities increasing with their distances, by 180 km/sec velocity increase for every million light year's distance. In short, the universe is expanding like an exploded bomb. Comparing the velocity increase per million light year's distance again indicates a zero time of some 5 billion years' Thus it appears that this universe had a finite beginning. Physical measurements and present theories permit some picture of our universe's birth. We know since Einstein that many forms of energy are equivalent, e.g., mass, and electromagnetic radiation, aspects of which are heat and light. Now with expansion, radiation density or equivalent mass decreases as a length factor to the 4th power, while mass as matter decreases at a length factor cubed. The temperature in outer space is now perhaps 100° absolute and the radiation mass equivalent is but 1/1000 the rarefied interstellar gas densities. Decompressing the universe to a starting point, however, raises temperature more rapidly than mass density, and results in a high radiation mass energy fraction, which since it is proportional to temperature to the 4th power suggests a zero point temperature of several billion degrees, brighter than any sun. "Let there be light and there was light," according to Genesis 1-3. Now what further initial conditions must there be to explain the relative abundance of the elements in the universe, which by spectral analyses of the earth's crust, stony meteorites, and the sun and stars is surprisingly uniform throughout. Some 55% of all cosmic matter is hydrogen, some 44% is helium and only 1% is made up of all the heavier elements in much the same proportions as on earth. These latter decrease logarithmically in abundance up to atomic weight 100, then level out. This consistent abundance distribution of elements in the universe may be generally explained by taking at Time Zero a hot neutron gas of density about 10-3 grams per cc, at a temperature of several billion degrees Centigrade, with a high radiation energy fraction. Generally neutrons break down into positrons and electrons within about ten minutes, but at the initial high temperature and radiation pressure would recom-bine. However, with rapid expansion and decrease of temperature and pressure, the neutron disintegration would run uncompensated and aggregation would result from neutrons and protons uniting in different degrees of complexity. The total calculated element aggregation time would be about one hour while the temperature still remained above one billion degrees. The element abundances formed would depend on density of the nuclear gas, simplicity of the atom formed, and the neutron capture cross section. Thus a higher density

Jan 1, 1964

By D. J. Rose, W. M. Armstrong, A. C. D. Chaklader

The wetiability of single crystals of MgO by specimens of vacuum-cast iron was studied using the sessile drop technique in vacuo at 1550ºC. Formation of FeO at the liquid-vapor interface caused the contact angle (6) to decrease from 117 to 65 deg during the first minute. After cooling, all specimens possessed a peculiar annular interfacial deposit of Fe,O,. Within the annulus the interface showed no sign of chemical attack. Chemical reaction occurred where the iron was alloyed with Ti, V, Cr, Nb(Cb), Ta, cmd Zr. Vnriation of 6 with alloy concentration was studied. Although vanadium md chromium improved the wettability of MgO by iron, the effect of Zr, Ti, Nb, and Ta was indeterminable because the 8 derived from sessile drop considerations was that of the metal against a restrictive peripheral volume of liquid oxide wetting the substrate. INTEREST in the nature of metal-ceramic interactions has been stimulated by progressive development of metal-ceramic combinations. One of the more valuable methods used for bond investigation is the sessile drop technique. Recent attempts to improve wettability through solute additions to the drop have revealed that the solute may a) react with the oxide creating new compounds at the solid-liquid interface, b) adsorb at the interface in a monolayer formation, or c) distribute throughout the drop uniformly causing no wettability variation. This work, part m in a series1,2 of investigations of interface reactions between metals and ceramics, embraces a study of the Fe-MgO system. MgO possesses a large negative free energy of formation (-173 kcal per g mole 0, at 1550ºC) compared to FeO at this temperature (-73 kcal per g mole 02). Hence the electronegativity difference between the drop and substrate allows selection from an extensive group of metal solutes with intermediate electronegativity differences that would, in the absence of chemical reactions, be expected to adsorb pre- ferentially at the solid-liquid interface. However, the high oxygen pressure of MgO in vacuo creates an oxidation environment which influences the solute behavior. Recent studies of the Fe-MgO systemJ74 have been restricted by chemical reactions that obscured observations. In view of the current interest in liquid-phase sintering of metal-ceramic combinations under partial oxidizing conditions,5 a more comprehensive study of the Fe-MgO system seemed beneficial. EXPERIMENTAL PROCEDURE 1) Specimen Preparation. Optical-grade MgO single crystals and Ferrovac vacuum-cast iron were used in all experiments. A spectrographic analysis of the iron indicated 0.008 C, 0.05 V, 0.005 Mo, 0.01 Ti, 0.002 S, 0.01 Cr, 0.001 Mg, 0.01 Si, 0.003 A1 (wt pct). The MgO crystals were cleaved along (100) planes into plates approximately 20 by 20 by 1 mm. Following annealing in vactto at 1100°C for 3 hr, surface irregularities were removed by a chemical etch in phosphoric acid at 100°C. The iron rod was machined into small cylinders approximately 0.250 in. in diam and length and these were carefully cleaned in organic and acidic solutions to remove surface impurities. All specimens were weighed to the nearest 0.1 mg. 2) Apparatus. The apparatus described in detail by previous authors1,2 was modified for this work. A Polaroid Land Camera was incorporated into the optical system so that drop measurements at ten-second intervals after melting were possible with ultra-high-speed self-develop ing film. 3) Procedure. The iron cylinders were placed upright on the MgO plates and positioned in the molybdenum susceptor. After furnace assembly the system was pumped down to a vacuum of 1 µ and flushed with H2 at 800°C. The system was again evacuated to 5 x 10-5 mm of mercury and the temperature raised to 1550°C within 2 min. The molten drops were photographed at appropriate time intervals. TWO min after melting the iron vapor pressure caused gas discharge, or corona, within the tube. The specimens were then slowly cooled to room temperature, sectioned and examined metallographi-cally. X-ray identification of interfacial reaction products was attempted by the powder diffraction technique. Alloying elements (Ti, V, Cr, Zr, Ta, Nb) were added to the iron in various concentrations up

Jan 1, 1963

By N. L. Carwile, G. W. Geil

A metallographic study was made of deformation twinning (Neumann lamellae) in ingot iron slowly deformed in tension at —196O and —150°C. The results showed that twinning is initiated mainly during the initial stages of plastic deformation. However, the breadth of the twins generally increases with increase in strain up to fracture of the specimen. HE results of an investigation of the effect of low I temperatures on the flow, fracture, strain hardening, and strain aging characteristics, and the true stress-strain relationship for specimens of ingot iron deformed in tension were reported recently.1,2 In that study specimens of ingot iron, in different initial conditions, were slowly deformed in tension at various temperatures between —196" and +100°C. A phenomenon observed, but only briefly reported, was the formation of deformation twins (Neumann lamellae) in the specimens deformed at the lower temperatures. Preliminary metallographic examination of these specimens indicated that there was apparently some correlation between the deformation twinning and the strain of the specimen and that this factor merited further investigation. Some recent investigations have indicated a direct association of Neumann lamellae and the fracture of the metal. Bruckner".' * postulated that the twinning immediately precedes the fracture and the latter is initiated by the stopping of the propagation of twins, either at subgrain boundaries or at other structural features. Tipper and Sullivan5 postulated that Neumann lamellae are initiated by the shock or a shock wave set up at fracture in the still highly stressed unbroken metal, and that a high rate of deformation is a necessary condition for their formation. An extensive metallographic examination, therefore, was made of many of the specimens used in the study of ingot iron at this Bureau and of additional specimens deformed to selected strains under various conditions. The present paper summarizes the effects of deformation under these conditions upon the breadth and scope of the deformation twins. Other features of twinning will be discussed in another paper. Material and Testing Procedure All of the specimens were prepared from one lot of ingot iron, as hot-rolled, of chemical composition other than iron as follows: C, 0.02 pct; Mn, 0.02; P, 0.005; S, 0.018; Si, 0.002; Cu, 0.10; 0, 0.058; and N, 0.002. Cylindrical tensile specimens with a 2 in. gage length were used. The reduced section was slightly tapered from each end; the diameter (0.438 in.) at the midsection of the gage length was about 0.003 in. less than at the ends. The specimens were finished to the final dimensions by grinding and polishing in the axial direction. The ends of the specimens were machined with 3/4 in. x 10 threads and the shoulder fillets were machined to a radius of 0.75 in. The specimens were extended slowly in tension (deformation rate less than 0.5 pct reduction in area per minute) while immersed in an appropriate cryogenic liquid maintained at the desired temperature. The minimum diameter of the specimen was measured during the test by means of a specially designed reduction of area gage accurate to 0.0001 in." A detailed description of the testing equipment and the method of maintaining the desired temperature is given in a previous paper.' Each specimen, after deformation to a specified strain at a selected temperature, was sectioned longitudinally and examined metallographically. The preparation of specimens for metallographic examination was carried out in the usual manner by mechanical polishing and etching. Results and Discussion Deformation twins in specimens of ingot iron extended slowly in tension at —196" and —150°C are shown by the representative micrographs of Figs. 1

Jan 1, 1954