Search Documents

By J. R. O’Connor

Stimulated emission from Nd+3 in yttrium uanadate fYVOJ is reported. Single crystals of YVO4:Nd, obtained from Linde Col-p., have improved substantially in the last several months. Pulsed thresholds of YVO, laser rods are now approximately 2 to 3 5, cowparable to tliose for YAG:Nd. Yttrium uanadate crystalli~es irz a space group similar to zircon. All rare-earth vanadates have this structure. Rare-earth ions sucll as Nd+3 which substitutes for Y+3, aye situated irz a strong tetragonal crystal field which lacks inversion symmetry. This condition increases the p'robability of the parity-forbidden f — f transitions. Yttrium anadate has strong absorption bands beyond -1000A. These are clue to Y-O, V-O charge transfer and molecular transitions. Under 2537 and 3660A irradiation pure YVO, fluroresces u bright yel-LOLO. This fli&orescence is corrzpletely quenched in YV04:Ncl crystals. This and other evidence of energy trut~sjer from the lattice is repovted. Optzcul atz 1user pvope 1-ties o! YI'U4:E[t are brieJy described. THIS paper describes some of the optical and laser properties of Nd+3- and Eu+3-doped yttrium orthovana-date (YVO4). It reports laser action for the first time in this low-symmetry host. For some time we have pursued a research program concerning laser hosts' wherein the rare-earth (RE) ion is situated at a site of low crystal symmetry so as to increase the probability of radiative transitions. Single crystals of doped and undoped YV04 are grown from iridium crucibles in an oxyhydrogen gas-fired furnace by a modified Czochralski technique.' This material crystallizes in a D4li tetragonal space group of the zircon (ZrSiO,) type.3 All RE vanadates have the same structure and form solid solutions with YVO4. Therefore, it will be possible to investigate a variety of cross-pumped laser systems, as in the case of yttrium aluminum garnet (YAG).4 At present, ~d'~-doped YAG is one of the most efficient solid-state lasers.5 Accordingly, most of the material to follow will compare the properties of YV04 to those of YAG. Fig. 1 shows the relative transmission of YAG and two types of YVO4. "Pure" YVO4 has a normal absorption edge and is colorless. A second type has a broad absorption peaking near 4200A and is yellow. Rubin and Van uitert6 suggest the yellow material is slightly reduced. Samples of each type are being investigated by electron spin resonance,7 but these studies are so far inconclusive. The pulsed laser threshold is much lower in the yellow material than in the colorless. Therefore, the absorption at 3500 to 5000.4 transfers energy to the Ndi3 ions. Photons of wave length between 2000 and 4500A cause undoped YVO4 to fluoresce at 4800, 5250, 5460, 5540, and 5750A. This emission, previously reported by Brixner and Abramsom,8 is partially quenched by EU'~ and completely quenched by Ndt3 at room temperature due to energy transfer from the lattice to the RE ions. At low temperatures, some lattice fluorescence is present. This implies that the energy-transfer process is in part phonon-assisted. Although the YVO, single crystals used in this work were prepared from Y2O3 containing less than 0.01 pct rare-earth impurities, there is aopossibility that emission lines between 4800 and 5750A are due to dysprosium, terbium, and so forth. However, these lines are not observed in other compounds, prepared from Y2O3, such as YP04, Y2MoO6, and so forth. Furthermore, extensive absorption measurements on our "pure" YV04 single crystals between 0.4 and 5.0 failed to reveal any characteristic rare-earth lines. Fig. 2 compares the absorption spectra of Ndt3-doped YAG and YVO4from 0.6 to 1.0 . The Ndt3 absorptions are labeled according to free ion, R-S coupling. These term designationsQ are appropriate for YAG:Nd. They appear to be inappropriate for YV04:Nd. In YVO, neodymium must substitute for yttrium. The yttrium site is situated In a strong tetragonal field, where point symmetry is (42m) or possibly lower.1° However, the reduced splitting of the Stark components of the YV0,:Nd spectrum implies that the NdT3 ion is in a cubic site. The only plausible explanation for this discrepancy is that the Ndt3 ion is in a low-symmetry site, lacking inversion symmetry, so that a substantial admixture of 4f and 5d wave functions occurs. In this case, R-S coupling is not valid and J is no longer a good quantum number." Consistent with this view, the 4~ metastable level of YV04:Nd has an oscillator strength larger and a

Jan 1, 1968

By W. F. Holbrook

THE problem of sulfur control is important in all blast-furnace operations but particularly for certain grades of steel because of the rigorous specifications. During the past decade the tendency has been to produce pig iron, and, hot metal of lower sulfur content. As most of the sulfur in the ion originates in the fuel, the use of high-sulfur coke demands modifications in practice to meet sulfur specifications. While it is generally known that high temperatures and more basic slags favor desulfurization, operators as a rule produce the most acid slag that will permit proper desulfurization. The viscosity of blast-furnace slag has been thought to be related to desulfurization and has been investigated by Feild and Royster1, also McCaffery and his associ-ates2, but apparently no systematic effort has been made to determine the relative desulfurizing powers of slags over the range of composition encountered in practice.

Jan 1, 1936

By H. C. Chao, L. H. Van Vlack

Small MnS inclusions with known crystallographic orientations were placed inside powder compacts of low-carbon steel. After the metal was axially campressed with negligible end friction, the deformstions for the metal and the inclusions were compared. The MnS inclusions deformed more when the [100] direction was aligned with the compression axis than when the [111] direction was parallel to this axis. The deformations of the inclusions in the two principal radial directions were equal for each of the above orientations. Inclusions with [110] compression alignments did not deform with radial symmetry. The relative deformation of the inclusion and metal was closely dependent upon the relatiue hardness of the two phases. The relative deformation of the two phases was not sensitive to the rate of deformation. RECENT studies by the authors1.&apos; suggested that the plastic deformation of MnS in steel would probably be highly sensitive to the orientation of the inclusions and to the temperature of the metal. This paper reports an investigation of these factors upon MnS behavior within steel. Manganese sulfide (MnS) possesses an NaCl-type structure and typically has extensive (l10) {110} slip as a separate (noninclusion) crystal.&apos; A secondary slip system, ( l 10) { l l l}, has also been observed where the major slip system is restricted. In general, MnS inclusions must be rated as a highly deformable second phase.3 The amount of sulfide deformation varies, however, with several composition and processing factors. Some of these have been only partially assigned. For example, it is known that minor amounts (<0.01 pct) of silicon within free-machining steels will increase the amount of MnS deformation,4 but the mechanism of the added deformation can only be surmised at the present. Manganese sulfide and steel have sufficiently comparable deformation characteristics so that slip which is started in steel may be continued through the sulfide inclusions and back into the steel if the crystal orientations are favorable.5 A more detailed discussion of previous work on the plastic deformation of NaC1-type crystals and on the plastic deformation of inclusions within a metal is given in Chao&apos;s work.6 EXPERIMENTAL PROCEDURE The manganese sulfide which was used in this study was prepared by previously described methods.&apos; Single crystals of MnS, both as cleavage cubes and as spheres, were oriented within steel powder compacts so that the desired crystal directions were parallel to the direction of axial compression. A four-stage hydrostatic compaction procedure was used and involved the following steps. In the first stage part of the powder was placed in a metal die 1 in. in diameter with a thick (1 in. OD, 5/8 in. ID) rubber liner which had one end plugged. The steel powder was hand-rammed, making it as dense as possible before placing a carefully sized MnS crystal (either as a sphere or as a cube) near the center. The crystal was oriented with the chosen direction vertical; viz., [001], [011], or [111], with the aid of a X10 microscope. A pair of tungsten wire threads 0.020 in. in diameter was inserted along the side of this (&apos;core compact" to locate the desired plane after the compression tests. After the crystal was positioned in the center of the die, more powder was added and carefully rammed by hand. The die was then capped with a rubber plug of the same hardness and thickness as that of the liner. The whole assembly as shown in Fig. 1 was compacted by a ram load of 54,000 lb (about 70,000 psi). In the second stage a smaller, 3/4-in, rubber-lined die was used to give a stress of approximately 120,000 psi. The above process was repeated with the initial compact serving as a core for a larger compact. The final product after sintering was a cylinder 1 cm long and 1 cm in diameter, having a density of 7.54 g per cu cm. This was close to the theoretical density since the metal contained a non-metallic phase. There was no evidence of MnS deformation during the hydrostatic compaction or subsequent sintering. Elevated-temperature hardness data were obtained by procedures previously described.2 Compression tests for inclusion deformation utilized the cylinders which were described above. The critical problem in these tests was the lubri-

Jan 1, 1965

By A. E. Blakeslee

Morphological and electrical properties of GaAs epitaxial layers are influenced not only by changes in the nominal substrate orientation but also by small amounts of misorientation from the exact crystal planes. Deviations up to 5 deg from {11IA}, {11IB}, and (100) planes were investigated. Growth rates increase progressively with angle, approximately I u per hr per deg. Size and density of growth pyramids fall off with increasing angle, but other effects that are deleterious to the surface may occur which are heightened by increased misorientation. Carrier concentration decreases and electron mobility consequently increases as the angular offset increases, except in the case of strong compensation, where the mobility trend is reversed. It has long been known that changes in the crystallo-graphic orientation of the substrate may cause pronounced effects on the morphological properties of vapor grown semiconductor films. Reports of orienta-tion-dependent growth rates and surface characteristics are as old as the literature on epitaxy itself. shawl has recently published a comprehensive study of the dependence of growth rate on substrate temperature and orientation in epitaxial GaAs. It is also well-known that misorienting the substrate surface a few degrees away from the nominal low-index crystal-lographic plane often produces a much smoother epitaxial surface. This was reported by Tung2 for silicon, Reisman and Berkenblit3 for germanium, and by Kontrimas and Blakeslee4 for GaAs, and use is commonly made of this fact in the semiconductor industry to help guarantee smooth vapor deposits. The effects of substrate orientation on the carrier concentration and mobility of vapor grown GaAs were first documented by williams5 in 1964 and have been observed by several other authors since then,6,7 but no one has yet reported a careful study of how small changes influence these properties. We have made such a study and have found that sizable differences in growth rate, morphology, carrier concentration, and mobility can indeed be observed for epitaxial films grown on substrates that are oriented by progressive small increments away from the exact crystal plane. EXPERIMENTAL Early in the investigation an arsine synthesis system of conventional design8 was employed to produce growths on {111A}-oriented GaAs substrate crystals. In that early work, pronounced effects on carrier concentration and electron mobility were observed as a function of slight misorientation from this low index plane. That observation led to the more careful study that is reported here. An AsC13 system, differing in major aspect from those commonly in use today9 only in that the reactor is vertical rather than horizontal, was used for the detailed study. The gallium source was at 900°C and the substrates were at 750°C. The flow rate of pal-ladium-diffused H2 through the AsCl3 bubbler was 200 cu cm per min, and the flow rate of bypass H2 was also 200 cu cm per min. The substrates consisted of chro-mium-doped semiinsulating GaAs to facilitate elec-trical evaluation of the overgrowth by means of Hall and conductivity measurements on conventional eight-legged Hall bridges. They were misoriented by 0 to 5 deg from the {111A}, {111B}, and (100) planes, toward the (100) from the {111A} and {111B} and randomly toward the <111A> or <111B> from the {loo). The crystals were oriented for sawing by the Laue back-re-flection technique, which is good only to about ±1/2 deg; but after polishing or sometimes after epitaxial growth the wafers were checked by a diffractometer technique which is accurate to about * 0.1 deg. After lapping, the wafers were polished with NaOCl after the technique of Reisman and Rohr,10 and just before use they were cleaned in NaOC1, thoroughly rinsed with de-ionized water, and blown dry with nitrogen. Each run employed four wafers, each misoriented by differing amounts from one of the three major faces, and at least two runs were made for each orientation. The runs were continued long enough to provide at least a 15-µ or thicker layer. SURFACE MORPHOLOGY The appearance of all the films that were grown in a given run always changed from wafer to wafer as a function of increasing misorientation, but not always in the same regular fashion. At least three different trends were observed. These are more easily seen than described, and reference to the series of photo-

Jan 1, 1970

By Arthur M. Miller

FROM the time of its establishment in 1933, the Tennessee Valley Authority has been active in the field of phosphates. Under the T.V.A. Act it has a broad Congressional mandate to guide a unified development of the resources of the region for the long-range benefit of the people. As one phase of this function, it is directed to co-operate with farmers in the experimental large-scale use of improved fertilizers and development of better fertilizer practices. Following careful study, it was concluded that the objectives of this phase could best be attained by soil rebuilding through the use of phosphatic fertilizer and lime in an improved farm management sys- tem. This activity was launched through a program of test and demonstration on farms and simultaneous technical investigations to develop new and improved phosphatic fertilizers. Phosphorus has since become a keystone of the Authority&apos;s resource development and conservation program. Human effort is being conserved by phosphate utilization on the farm, and mineral conservation has been promoted by technical developments in phosphate mining and manufacturing operations.

Jan 1, 1944

By Oliver S. North

Reserves of perlite rock in the western section of the United States are immense. A geological report prepared for the Union Pacific RR showed proved tonnage of over 400 million tons in southern Nevada alone. Yet the perlite industry is not large, and most of the mines are relatively small. There are indications that perlite processing, thus far largely in the hands of relatively small com¬panies, is becoming concentrated in a few large companies. For economic reasons the bulk of perlite sold in crude form has come from three or four pro¬ducers, although many individual operators have sold small quantities to limited lists of purchasers. Perlite is one of ultra-lightweight aggregates. Owing to its outstanding qualities as an aggregate, variety of uses, and ultimate economy of use, it has enjoyed considerable popularity in this country in recent years. Marked foreign interest also has been evinced in this material.

Jan 2, 1955

The Sub-committee on Safety of the Industrial Organization Com-mittee of the Institute has been asked to cooperate with the National Safety Council, and has made certain recommendations to the Board of Directors of the Institute regarding ways and means of bringing about this cooperation. The National Safety Council has been in existence seven years. Its inception was at a meeting of the American Iron and Steel Electrical Engineers held in Milwaukee in 1912. The first annual congress was held in New York City in October, 1913, at which time the Council was definitely organized. Its membership now consists of nearly four thousand members, representing industrial plants, railroads, public utility companies, insurance companies, state labor commissions, Chambers of Commerce, manufacturers&apos; organizations, etc. These members are in all states of the Union and in eleven foreign countries, and through them the National Safety Council reaches more than six million workers.

Jan 7, 1919

By George M. Fowler

MINING geology is a progressive study, so we must look to the future for the solution of many of its most significant problems. These problems, world-wide in scope, offer ample opportunity for the exercise of the utmost skill and intelligence by all that attempt to solve theta, as it is generally recognized that many ore deposits of the future will he found only by months or years of combined intelligent effort by the several engineering groups. Renewed appraisals are continually being made to better understand the relationship of physical-chemical processes to ore deposition and other mineralization and to interpret the findings of the geophysicists and others in terms of economic results. A study of current geologic activi¬ties clearly reflects the growing tendency for cooperation between the different branches of geology in order to appraise their united efforts. In line with these activities arrangements have been made to transfer the geophysical section of the U. S. Bureau of Mines to the Geological Survey.

Jan 1, 1936

By ELTCENE A. WHITE

WE are all interested in our ou7n lines of endeavor and consider ourselves the center of the universe. The farmer thinks he is the most important man because he feeds us. The doctor knows he is the real center because he keeps us well. The lawyer says that he is indispensable because he keeps the peace. The banker furnishes us a place to keep our money and tells us how to make proper use of it. The miner sags that without metals there would be no civilization. I think that my branch has sufficient interest and exhilaration. of accomplishment to fully occupy any man&apos;s mind and attention. Mining and metallurgy are as old as the human race. It did not have much, if any, importance in the stone age as there are not found remains of iron and copper, but in the bronze age, which was co-existent with the stone age, it came to the front. Iron and copper were the most important metals. Copper, as bronze, was known in ancient Egypt, I\~:IS important in Rome and other parts of Europe and in Asia; in South America among the Aztecs and farther North were the Mound Builders and the early inhabitants of Lake Superior. At a very early date the Egyptians conquered the Sinai peninsula for the sake of the copper produced there. The history of copper metallurgy can be compared to that of a flower. The seed is sown in darkness and in the Dark Ages the crude metallurgy of copper began. As the shoot comes up from the seed it may be compared to the age of alchemy; the branches of the plant can be compared to the Middle Ages; the flowering shoots to the 17th century, the budding to the 19th and the blossom to our own time from 1870 on.

Jan 1, 1930

By Che, C. W. Spencer, C. A. Steidel, Yu Li

Grain boundary grooving as it occurs in a 5.5-deg simple-tilt nickel bicrystal immersed in a saturated Ni-S liquid has been studied. A 1/3 (t= time) dependence for the depth of the groove indicates that the rate -controlling meckanism for groove developvnent is volume diffusion in the liquid. The activation energy for the diffusive process is estimated at 15 kcal per mole. Using an extended form of W. W. Mullins&apos; analysis for grooving reactions, a computer is employed to fit the appropriate diffusion equation by a numerical method. From the analysis a possible method of measuring L.S. the solid-liquid interfacial tension is demonstrated. WHEN a polycrystalline solid is heated in equilibrium with a saturated fluid phase, grooves will form at the intersections of the grain boundaries and surface. The equilibrium root angle of these grooves is determined by the balance between the grain boundary and solid-fluid interfacial tensions. The grooves deepen and widen with time due to a difference in chemical potential between the flat interface and the curved interface of the groove. In this investigation solid-liquid interaction at a grain boundary is studied, with the object to determine the mechanism of grain boundary grooving in the presence of a saturated liquid. Extension of Mullin analysis then permits the estimation of the solid-liquid interfacial tension. Herring has demonstrated by dimensional analysis that the quasi-steady state change of the dimensions of a small particle during sintering is proportional flow, evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, respectively, if geometric similarity of consecutive configurations of the particles holds. Mullins has extended this analysis to grain boundary grooving. In the case of shallow grooves he solves the diffusion equations for evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, and obtains the same time dependence for any linear dimension of a groove as Herring found for the change in dimension of small particles. In Mullins&apos; analysis2&apos;3 grain boundary grooving of a bicrystal by volume diffusion in the presence of a saturated fluid phase was considered. Several assumptions were made prior to the analysis: 1) the solid-fluid interfacial tension is independent of crystallographic orientation; 2) the Gibbs-Thompson equation relating curvature and chemical potential is applicable at the solid-fluid interface; 3) the relaxation time of the diffusion field is small compared with the time for appreciable changes in the curvature of the groove, so that the diffusion is divergence-less; and 4) the groove has a small slope relative to the initial flat interface. Usually this last condition is fulfilled only for solid-gas systems. The solution of the diffusion equation under the above conditions produces a t1/3 dependence for any linear dimension of the groove in the case where volume diffusion is rate-controlling. The t1/3 dependence is valid because geometric similarity of the grooves exists for all time. EXPERIMENT In the experiment a 5.5-deg nickel bicrystal of <100> simple-tilt orientation was used.4 Grooving was studied in the presence of a saturated Ni-S liquid alloy as a function of time at 750°, 800°, 850°, and 900°C. A low-angle bicrystal was chosen for study to insure that 2L.S. > .b., where l.s.

Jan 1, 1964

By E. W. Pehrson, J. W. Furness

NONMETALLIC MINERALS, exclusive of fuels, may be divided into three groups: Building materials, fertilizer minerals, and miscellaneous minerals. Building materials, such as sand, gravel, slone, lime, and the ingredients of cement and clay products, occur widely in nature and are thus available near consuming centers at relatively low prices. Cost of transportation over great distances deters any&apos; substantial movement in world trade. On the other hand, fertilizer minerals, such as phosphate rock, potash, nitrates, sulfur, and pyrite, and the miscellaneous nonmetallic minerals, such as long-fiber asbestos, mica, graphite, fluorspar, and china clay, do not have such widespread occurrence and consequently contribute the major part of the world&apos;s commerce in such minerals. The U. S. Bureau of Mines has prepared charts showing the inter-

Jan 1, 1936

By W. C. Hellyer, R. A. Campbell

In single-stage autogenous grinding, the buildup of a critical size fraction in the media can be corrected by removing this material through pebble ports, crushing it below the critical size range, and recycling the crusher product back to the mill. The rate at which the critical sire fraction is crushed affects the size distribution of the grinding media and this in turn affects the sire distribution of the grate discharge. This provides a means for controlling the grind produced by a single-stage autogenous grinding unit. The pilot-plant investigations on a very hard copper ore were carried out at the facilities of the Institute of Mineral Research, Michigan Technological University. In an autogenous grinding circuit in which feed at approximately 9 in. top size is reduced to a size suitable for subsequent processing, the build-up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge."&apos; The buildup of a critical size fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large-diameter steel balls to the grinding charge. This has certain disadvantages, such as 1) an increase in mill liner wear, 2) wear on the steel balls, and 3) some loss in flexibility in grinding circuit opera-tions resulting from difficulties in removing the steel balls by means other than by grinding out. A number of investigators&apos; have suggested the use of a small crusher as an alternative to the use of large steel balls for control of a critical size fraction. With this technique the critical size fraction is removed from the mill continuously through suitable-sized pebble ports, crushed below the critical size range, and returned to the mill. An external crusher would cause no increase in mill liner wear, the wear on the crusher would be less expensive than the wear on the steel balls, and the flexibility of the grinding circuit operations would be enhanced since the crusher can be cut into and out of the circuit at will. This paper describes an autogenous grinding pilot plant investigation on a very hard copper ore, which led to the selection of an autogenous grinding flowsheet incorporating a crusher in the circuit as the preferred method for grinding this ore. Further development of the technique demonstrated that the crusher could be employed to control the product produced by an autogenous grinding unit. Description of Pilot Plant These investigations were carried out at the pilot-plant facilities of the Institute of Mineral Research, Michigan Technological University, Houghton, Mich. The autogenous grinding unit was a 6-ft-diam by 2-ft-long Hardinge Cascade mill with %-in. slotted steel grates. Pebble ports cut into the grates allowed passage of pebbles having a top size of approximately 21/2 in. The grate and pebble-port discharge material passed over a 3/16-in, trommel screen with the trommel under -size being pumped to the classification device. DSM screens were employed for classification in the early investigations, but were replaced later by a small Dorr rake classifier. The trommel oversize material returned to the mill via scissor conveyors. When the crusher was incorporated into the circuit, the trommel oversize material passed to a double-deck vibrating screen fitted with 2-in. and 3/4-in. square mesh screen cloths. The $ 2-in. and the —2 +3/4-in. size fractions were combined and crushed to a nominal 1 in. in a 4 x 6-in. jaw crusher. The crusher discharge and the —3/4-in. screen undersize returned to the mill. In the final investigation, a flap gate fitted to the top deck of the screen directed the — 21/2 +2-in. size fraction to the crusher or back to the grinding mill. The flap gate operated manually on a 15-min cycle, with this material being crushed for so many minutes out of each cycle. This was found to be a more reliable method of controlling the amount of — 21/2 +2-in. material crushed than attempting to make a split of a small weight of material on a continuous basis. Operational Techniques: Each sample was sized into three fractions and the Cascade mill feed was reconstituted from these size fractions in the proportions existing in the original sample. Sufficient feed for 15 min operation was weighed out and fed by hand over a 15-min period. The gross mill power draft was recorded every 15 min, corrected for tare power and drive efficiency, and reported as net kilowatt-hours per ton. A recording kilo-watt-hour meter provided a continuous visual record of the power drawn by the mill. Pulp densities of the trommel undersize and the classifier overflow (or DSM undersize) were taken every 15 min. The classifier overflow was sampled automatically. Timed samples of the classifier sands were taken every 15 or 30 min, weighed, and returned to the circuit. After correcting for moisture content, the weights were converted into percent circulating load. Timed samples of the +2 in., the —2 + 3/4-in., —3/4-in. screen fractions, and the crusher discharge, were

Jan 1, 1971

By J. Chipman, H. R. Larson

The data previously reported for the quantity as a function of oxygen pressure at 1550°C have been used to compute the activities of Fe, FeO, Fe2O3, and COO in slags of the ternary system. Activities of the first three have been obtained also for two quasi-ternaries involving fixed CaO:SiO2 ratios. IN a previous paper1&apos; the authors reported the results of an investigation into the effects of oxygen pressure on the composition of various simple slags analogous to some of those which are found in steel-making practice. The ratio of ferric iron to total iron was studied at 1550°C in iron oxide melts to which lime, magnesia, lime-plus-silica, and other oxides were added. The oxygen pressures involved those of air, carbon dioxide, and carbon dioxide plus carbon monoxide in several proportions. Although very low oxygen pressures could not be used, the slag-metal equilibrium studies of Fetters and Chip-man&apos; permitted extending the results to slags in equilibrium with iron. For the ternary system CaO-FeO-Fe,O, the oxygen pressure-composition relationship has been determined from zero percent lime to lime saturation over an oxygen pressure range from air to that represented by equilibrium with liquid iron. Lime and silica were added to iron oxide in the ratios 0.54, 1.306, and 2.235 to form three quasi-ternary systems which were also studied over the entire region of liquid melts at 1550°C. Ternary Gibbs-Duhem Equation Wagner" has developed a method by which the activities of two components of a ternary system can be calculated if&apos; the activity of the third component is known throughout the composition range being considered. The fundamental form of the Gibbs-Duhem equation for ternary systems is N, d In a, + N2 d In a, + N3 d In a3 — 0. Wagner has developed a usable form of this equation by introducing the term y = N3/(N3 + N1) and rearranging the equation to give (? In a1/?N2)x = -y/(1-N2)2 (? In a2/?y) x2 N2/1-N2 (? In a2/?N2) y To apply this equation to the slag system CaO-FeO-Fe,O,, the activity of one of these components must be known. However, the only activity which is known from the experimental data is the activity or pressure of oxygen in the gas phase with which the slag is in equilibrium. The activity of oxygen in the slag can be defined as the square root of the oxygen pressure. In order to use oxygen as one component, the composition of the slags must be converted to the basis Fe-O-CaO. Oxygen, exclu-sive of that contained in CaO, then becomes com-ponent 2 in Eq. 1, Fe is selected as 1 and CaO as 3. Then y = Ncao/(Ncao + NFe). Eq. 1 then becomes (? In a fe/? Nx) y = -y/(1-No)2 (? In ao/?y) xp - No/ 1- No (? In ao/ O No) y. In order to evaluate Eq. 2, the boundary conditions must be known. The obvious choice of a standard state for iron is to assign slags in equilibrium with iron an activity of one. Then In a,., or log aFe, which is substituted for convenience, is determined by integrating along a line of constant y from the slag in equilibrium with iron to the composition at which log a,, is to be determined. Mathematically this can be expressed as log aFe (Nlog y) = log a&apos;Fe + (? log a Fe/? No) dNo where the primes indicate equilibrium with liquid iron and a&apos;Fe = 1. When Eq. 3 is integrated along a line of constant y, the following is obtained: log a Fe (No, y) = - y No ?/ No ? y ( log ao/(1- No)2) No d No - No/1-No d log ao. Lime-Iron Oxide Slags Iron Activity: The oxygen pressure of lime-iron oxide slags is shown in Fig. 1 as a function of j, de-fined as j = Fe+++/(Fe++ + Fe +++) for various constant mol percentages of lime. The j values at 0 to 60 pct lime were then determined for oxygen pressures of 1, 10-1, etc. to 10-" atm. For purposes of calculation, the line for zero percent lime was extrapolated to

Jan 1, 1955

By J. D. Price, W. M. Bertholf

A. C. RICHARDSON*—First of all, [ think that the paper represents a lot more work, study, and correlation than has been indicated by the brief talk by Mr. Price. I like the way he started out and described the areas from which the samples were obtained, the locations of the washing plants, the available tonnages, and other background information with which to evaluate the data he submitted later on. Then I like the way in which he described the various types of washing plants, the tonnages handled and the difficulties of the washing problems; showing the amount of material that lies close to the specific gravity at which the washing separation is made. Later he gave figures from washing plant operations showing recoveries and cleaning efficiencies. He then discussed his own plant at Pueblo. It is the same old plant, I think, that I worked around a good many years ago. It is unusual to find a plant treating nearly 5000 tons of coal a day on tables. But this table plant is, I believe, more efficient than is indicated by the figures that Mr. Price gave. To determine the efficiency of a cleaning operation or to compare it with another it is necessary to consider the quantity and character of the material close to the specific gravity at which the separation is made. It is not fair, I believe, to penalize the table operation by something like 4 pct of out-of-place-material as he has done here. The variety and difficulty of the coals that he has to wash, the continuous shift and change in their composition make a very difficult cleaning problem and the table performance is excellent. I believe that the information in this paper will be of interest and value to anyone operating or planning to build a coal cleaning plant in this or other areas; particularly where the cleaning of fine coal is a problem. The data may be used for comparative purposes in determining the relative efficiencies of other cleaning plant separations. E. D. HAIGLER*—What is a Baum jig? J. D. PRICE (authors&apos; reply)—A Baum-type jig is one in which the pulsations of the water is secured by means of a pulsating air current applied on top of the water. I imagine you are all familiar with the old plunger-type jig which is in effect a U tube in which a plunger on one side of the U, moving up and down, causes a corresponding pulsation on the far side of the jig. In the Baum jig, the pulsating air current is applied on the surface of the water on one side of the U tube of the jig and gives a corresponding pulsation on the other. It is also commonly known as a pneumatic jig. The control of the rise and fall of the water in the jig body proper is under much better control than it is in any of the other type jigs. Mr. Richardson could enlarge on that feature, for I know that he has had considerable experience with these jigs. A. C. RICHARDSON—You have asked how to control a Baum-type jig. The pulsations in a Baum jig can be modified and regulated to a marked degree by the amount of water admitted to the jig and by the adjustments of the valve which regulates the manner in which air is admitted. The number of pulsations per minute is controlled by the number of cycles of the air valve. Thirty to forty cycles per minute is a good speed for large jigs treating coarse sizes of cod. With an air valve it is possible to modify the time-velocity curve of the pulsating water to some extent which in turn determines the action in a jig bed. Within limits the following parts of the air valve cycle may be regulated: (1) the rate and period of air admission, (2) the period of air expansion, (3) the rate and period of air exhaust, and (4) the period of air compression. The rate and period of air admission determines the acceleration of the water at the beginning of the pulsion stroke and the amplitude of the stroke. The period of air expansion, after inlet port is closed, is one in which the water has reached the desired velocity, positive acceleration reduced, and the bed held in a mobile condition. The rate and period of the air exhaust can be adjusted to modify the degree of suction and so modify the manner in which the particles in the bed stratify. The compression period, alter the exhaust port closes and before the intake port opens may be used to advantage in retarding the downward velocity of water during the suction stroke. An ideal jig stroke is one in which during the up stroke the bed is lifted slowly in a mass and opens up like an accordian with the bottom layers dropping away first. With the bed open and mobile the particles adjust themselves according to their hindered settling rates. During the down stroke, while the bed is still open the particles of high specific gravity are accelerated toward the bottom layers. It is possible to approach this stroke with all types of jigs but it is less difficult to approximate it with a Baum jig.

Jan 1, 1950

Jan 1, 1925

By J. A. MacLellan, John C. Bowling, J. R. Davenport, G. M. Ellis

Six months out of the year the cold is always there, and it seems to be waiting for someone to make a mistake. The simplest things can shut down a multi-million dollar plant besieged with -40°F temperatures and a 40 mph wind. It takes only one man-door improperly latched to feeze up all the pumps on the bottom floor. Someone can poke a one inch hole in an outside wall in July and six months later, the whole plant is flooded because the main water line just froze up and burst. Some important things must be remembered in plant design for cold and remote areas. For one thing, everything in these areas is more expensive due to long and difficult supply lines. Fuel is expensive and would be a major cost item even if it were not expensive, due to the extended periods of low temperatures. Building volumes should therefore be kept to an acceptable minimum. Service areas, on the other hand, must be adequate, because maintenance generally has to be conducted inside in a heated area. Supply vehicles, for instance, have to get completely inside the building to unload. If you try to unload a supply vehicle with the door open at -50°F, you won&apos;t be able to find the vehicle for fog and if you take more than 5 minutes half the water lines in the plant will freeze UP.

Jan 1, 1972

By Allen Rogers

THERE are few natural monopolies comparable with the nitrate industry. Perhaps the only other one is, curiously enough, also an essential fertilizer material, viz., potash, of which the Germans have heretofore held practically a-monopoly due to the existence in their territory of the most important known deposits of potash salts. And although nitrates in minute amounts are found in many desert regions, the only deposits callable of being worked commercially exist in Chile. Combined nitrogen in the oxidized form is an essential for plant life. Nature provides it mainly through the agency of nitrogen-fixing bacteria. But where lands are cropped artificially this supply is too small; and gradually the nitrogen supply becomes exhausted. In order to continue farming, it is necessary to furnish a supply of nitrogenous plant food, and this is clone by putting on various substances containing combined nitrogen. These consist of various animal wastes, ammonium sulphate, the ammonia of which is obtained in the destructive distillation of coal, and Chile saltpeter. The latter is immediately available as a plant food, the nitrogen being in the required form. The other substances must oxidize before they are available. Besides its use as a fertilizer, Chile saltpeter is the source from which the bulk of the nitric acid of commerce is derived. The use of nitric acid in the manufacture of almost, all modern explosives is, of course, well known.

Jan 2, 1918

Transit A light weight, totally enclosed theodolite, especially designed for mining, has been placed on the market by Askania Werke, A. G. The instrument weighs only 41/4 lb and measures 51/8 x 71/2 in. without tripod and in a waterproof aluminum hood. It may be mounted on tripod or bracket without removing the protective hood. [ ] Standard equipment includes diagonal eyepiece rotating in all directions which eliminates need to be in line with scope for sighting and makes an auxiliary scope unnecessary for steep sights. The transit reads direct to 1 minute and may be estimated to 6 seconds by means of optical micrometer on both horizontal and vertical circles. The telescope in vertical position serves as optical plummet, sighting through an opening in the base. The instrument is shown above mounted for attaching to a pin driven in timber or rock, eliminating tripod or set-up bar in cramped quarters. The chain clamp in the lower picture is used on timber or steel ground supports. Complete with carrying case and set-up brackets, ready for use in a raise, it weighs less than 6 lb, and the protective hood remains on until the instrument is securely mounted. [ ] Accessories for increasing versatility of this mining theodolite are: tripod, electric illumination for optical micrometer and reticule, close range objective lens, and objective lens prism for sighting vertically in front of the instrument. Circle No. 1

Jan 1, 1952

By Warren Blauvelt

IN VIEW of the enormous wastes of natural resources, of labor and of capital, due primarily to the economic environment, established by legislation, the general neglect of this phase of the problem of the elimination of waste is difficult to understand. In such a study, the engineering method of attacking a problem should be employed. The engineer does not try to solve his problem by disregarding natural laws, but by utilizing them. The successful engineer establishes an environ-ment in which forces, acting in harmony with natural laws upon an object or objects, will produce the desired results. The engineer who notices that the water level in a vessel, into which a gallon of water per minute is flowing, is two feet higher than the level in an adjacent vessel, connected therewith by a 6-in. pipe, does not assume that the law of gravity has ceased to work, or that water no longer seeks its level; he examines the connecting pipe for obstacles which prevent the free flow of water. Some editors, many reformers and most politicians tell us that the law of supply and demand no longer works; hence governmental control of commerce is necessary. Governmental control may temporarily-that is, until trial proves its futility- "insure domestic tranquility" and "promote the general welfare;" but it cannot "secure the blessings of liberty" which it cur-tails, nor can it "establish justice" which it violates.

Jan 9, 1922

By Bruce A. Kennedy

The first light of dawn was appearing through the window of the giant Pan American Boeing 747 as we crossed the Irish Coast on course into London&apos;s Heathrow Airport While still over Ireland, the plane began its descent and a few minutes later an announcement on the public address system informed us that we were coming up on Lands End. Cornwall, and would then begin our final approach into London. Barely visible below through the WISP). clouds were the Seven Sisters Lighthouse and the rugged cliffs of Lands End and Cape Cornwall, the westcrnmost point of England. Start at Lands End To a displaced Englishman, it seems amazing that technology has brought us to a point where large jet aircraft use Lands End as the starting marker for final approaches into London. It was not so very long ago that we considered the eight-hour car journey or the 12- hour train trip from London to Lands End as a major undertaking. Today, with the 180,000-lb thrust of four engines, this enormous aircraft transports 350 or more passengers that distance in a matter of a quarter of an hour. The incongruity of the situation is that the technology leading up to the development of the powerful jet engines used on: today&apos;s aircraft started with the ; invention of the steam engine which found its first commercial use some 300 years earlier in the mines of Cornwall 20,000 ft below.

Jan 1, 1971