Search Documents

By Joe B. Alford

Jan 1, 1971

By AIME AIME

THE paper by C. H., Lieb on the "Economics of Oil-Producing Practice" (June issue, M. & M.) contains much food for thought. The engineers should be gratified that an executive with Mr. Lieb's. responsibility should recognize their standing in the industry. Yet after giving them that recognition, he proceeds to spur them on to greater accomplishments by pointing out that their job is only partly done and in some instances poorly done. The operating policies in this paper when applied to new pools with flowing wells are sound. Neither do I take exception to their application to pumping wells. But I do wish to comment on what lie says about price when applied to the many more wells that are approaching abandonment that is, the small producing wells. Mr. Lieb states in effect that higher prices would be detrimental from the long range viewpoint. I doubt that the present prices of crude will provide an ample return from the hundreds of thousands of small wells that have possibilities of substantial recovery by means of water-flooding, repressuring with gas, and air drive. Probably expenditure for experimental work can he justified, but at this time it must usually be considered as experimental. Recently I visited a property where it was estimated that $250,000 would be spent on a 160-acre tract for flooding purposes. The rate of r e t n r n and amount of profit at today's prices are uncertain. It can be argued that if this type of recovery is not economic with crude at $1 then it can he delayed as it is now possible to secure economically an ample supply of crude from our flush fields. But these old fields still retain large quantities of crude in a dormant state, and should not he abandoned per-

Jan 1, 1936

By A. C. Fraker, H. H. Stadelmaier

In the systems Mo-Fe-C, Mo-Co-C, and Mo-Ni-C the phase boumdaries of the cubic Ij carbides were determined at 1000°C and the variation of the lattice parameter with composition was measured. In the system Mo-Fe-C a single ternary carbide, Mo3Fe3C, was observed. In Mo-Co-C and Mo-Ni-C two new n phases of the type M12C were found: Mo6C06C and Mo6Ni6C. At 1000°C they coexist with the M6C phases MO3-4,CO3-2C and Mo3-4Ni3-2C, respectively. Mo3C03C and Mo4C02C are not separate phases but parts of a single M6C phase region, and the same is true of Mo3Ni3C and Mo4Ni2C. THE n carbide structure type has been known since it was determined by westgren' in 1933, yet reliable information on phase compositions of this type is ap-parently scarce. The following selection of suggested formulas illustrates the extent of the confusion con-cerning compositions: W2-3Fe4-3C,1W6Fe6C,2 W2_4Fe4-2C,3 (W,Fe)6C,4 Tj.-W4Co2C and nz-W6Co6C,5 n1-W3Co3C and n2-w4Co2C,5 W3C03C and w6Co3C2,7 MO3Fe3C,8n2-M04Fe2C,9 (MO,Fe)6C,4 MO3CO3C,8 n2-MO4CO2C.9 Many of these compositions obviously overlap, some disagree in carbon content. The use of the designations 77, and n2 is not consistent. There is uncertainty whether two carbides M6C coexist or whether there is only one M6C with a wide range of substitution of one metal for the other. The existence of M12C seems questionable altogether if one ignores the results of a neutron diffraction study of W6Fe6C supporting that particular metal to carbon ratio.'' More reliable information is available for the iso-typic oxides studied by Nevitt,11 Nevitt, Downey, and orris," and Meussner and carpenter.l3 That n car-bides and oxides are structurally identical, particularly with respect to the location of the metalloid atom, has been demonstrated clearly by Stadelmaier and Meussner14 and also by Parthe, Jeitschko, and sadagopan.15 Therefore the present paper, which attempts to establish the phase boundaries of n defini-tively for three carbon systems, has implications for the whole family of filled Ti2Ni types. EXPERIMENTAL PROCEDURE The samples were prepared in two stages. Pellets weighing 3 g were compacted from powders of the elements and presintered in a closed tube of fused silica that had been evacuated to lO-4 mm Hg. This was fol- lowed by arc melting the sintered samples under argon. Remelting the button once was sufficient to produce homogeneous specimens. The metal powders had the following minimum purities in wt pct: molybdenum 99.5, iron 99.0, cobalt 99.7, nickel 99.9, graphite 99.94. Carbon determinations by the gas volumetric method were obtained from thirty-one of the one hundred samples in the annealed condition. They were limited to compositions that were critical to placing a boundary line in the isothermal sections. The carbon losses were comparatively low and averaged less than 1.5 at. pct. For annealing, the samples were sealed in tubes of fused silica evacuated to 10-4 mm Hg. The annealing schedule was 20 hr at 1250°C followed by 150 hr at 1000" ±10°C. For the water quench the silica glass tubes were broken mechanically to speed the quench. The specimens were examined in the as-cast and annealed condition by standard metallographic techniques. Some of the as-cast and all annealed samples were studied by X-ray diffraction using a 114.6-mm powder camera with filtered Co radiation. The lattice parameters of the n phases were determined by graphic extrapolation to 8 = 90 deg on a plot against sin2 8. It is estimated that the maximum error in the lattice parameters is ±0.002A.. The phase fields were determined by the disappearing phase method, relying on X-rays for phase identification and on microscopy to detect small amounts of a phase. RESULTS Pertinent information on the binary side diagrams has been summarized by Hansen and Anderko16 and Elliott17 and will not be discussed further. Photomicrographs documenting the equilibria at 1000°C have been selected to avoid redundancy due to the similarity of the three systems. Thus there will be only one picture showing an equilibrium with Mo2C, and so forth. Molybdenum-Iron-Carbon. An isothermal section of most of the Mo-Fe-C system at 1000°C is shown in Fig. 1. No attempt has been made to distinguish between a and y iron or to determine their phase boundaries. A conspicuous absence is the phase Fe2 1Mo2C6 with the Cr23C6 structure, supporting the suggestion by Krainer4 that it decomposes by annealing at high temperatures. The only ternary phase is found in a narrow range around Mo3Fe3C (MO43Fe43C14). A microstructure with a two-phase mixture of Mo + n is seen in Fig. 2. The variation of the lattice parameter of n with the estimated composition is shown in in Table IA. The phase diagram does not agree with the results of Kuo9 who reported n2-Mo4Fe2C. Our lattice parameter Varies from 11.095A at the iron-rich end to 11.140Å at the molybdenum-richoend of the phase field whereas Kuo9reported 11.26Å for Mo4Fe2C. We are in agreement with the older work

Jan 1, 1970

By G. C. Stone

At the conclusion of my paper on the same subject read at the Boston meeting of the Institute, I offered to send some of sample No. 2 to any chemist who wished to analyze it. Eight chemists wrote to me for samples; so far I have received results from five. I give these results in a table (on the following page), together with the results previously obtained: As to the chemists and their methods : K is an iron-works chemist whom I only know by correspondence; lie writes: "No. 27(13.64) was obtained by the method I generally use, as follows : Dissolve 0.8 grams spiegel in hydrochloric acid and a little potassium chlorate, in a half-liter flask. Boil off most of the acid, add ammonia in slight excess, redissolve in acetic acid, using rather more than is really necessary, and then add 8 or 10 grams of sodium acetate and make up to the mark with warm water. Boil hard for fifteen minutes, then allow to settle (cool?), until the liquid reaches the mark, and withdraw 300 C.C. of the nearly clear liquid. Add to this an excess of hydrochloric acid, evaporate to dryness, take up with hydrochloric acid and water, and separate the iron by two precipitations with ammonia (I have often tested the ferric hydrate for manganese, but have never found any, if the separation by ammonia was properly made). Finally, precipitate the manganese as phosphate." Nos. 28, 29 (13.35, 13.07) were by Ford's method." No. 30 (13.50) was by Troilus's method He writes, " I may add the results are quite as good as I expected, although for any element except manganese, they are not close enough for anything like accurate work." L is a firm of commercial chemists of large experience who have made a specialty of iron work. Their method is as follows : Dissolve

Jan 1, 1884

By Dell P. Williams, Howard G. Nelson

The tensile behavior of magnesium single crystals at a temperature of 26º ± 2ºC was investigated at varying pressure levels from 760 to 8 X 10-8 tow. For crystals deformed at a constant linear strain rate of 0.061 min-1. there was no apparent effect of the vacuum environment down to 10-8 torr. However, from a vacuum of 10-5 torr down to the lowest pressure attained (8 x 10-8 tor,), the effect of the vacuum environment was to increase the strain at the end of the first linear (or easy-glide) stage and to decrease the slope of this stage; the magnitude of this effect was found to be dependent on pressure. The slope of the second linear stage was also decreased at the lower pressure levels; however, this effect appears to be caused primarity by the vacuum effect on the first linear stage. The magnitude of the vacuum-environmrnt effect was also found to be dependent upon strain rate. The reduction in flow stress at 5 x 10-8 torr, as compared to the stress in air, was obserced to be about 10 pct for a strain rate of 0.0250 min-' and 70 pct for a strain rate of 0.67 min-1. No systematic effect of pressure on the critical resolvled shear stress was observed. The data interpreted in terms of a modified form of Mott's work-hardening mechanism for hexagonal metals. It has long been known that surface conditions influence the mechanical behavior of materials. Roscoe 1 demonstrated the importance of surface conditions on mechanical behavior by testing cadmium crystals with oxide layers. He found that the "apparent" critical resolved shear stress for cadmium was increased approximately 2.5 times by the presence of an oxide layer 1000 atoms thick. The magnitude of this effect was dependent on film thickness with crystals having films less than 20 atoms thick still showing a definite increase. This observed strengthening could not be attributed to any strength of the oxide film because of 1) the thinness of the films and 2) an observed increase in the flow stress as deformation proceeded. Harper and cottrel12 obtained similar results on zinc crystals which had been etched and steamed to give artificially thick oxide films. However, in the course of this study, they also carefully examined the very early stages of plastic flow for zinc crystals which in one case had been electrolytically polished and in the other had been lightly etched to produce a thin film. They then found that the critical resolved shear stress for both surface treatments of the crystals was actually identical but that the etched crystal exhibited a much more rapid initial hardening rate. This had not been noted previously. This result indicated that, in fact, the film caused an increase in the stress for continuation of slip, rather than for the initiation of slip. Lipsett and King3 investigated the effect of evaporated gold films on the plastic behavior of cadmium single crystals. For large angles (=75 deg) between the specimen axis and the normal to the slip plane, they found that the stress-strain curve of the coated specimen always lies above that for a clean specimen. The shear strain at the end of the first linear stage was greater in clean specimens than in coated specimens and the slope of the second linear stage was

Jan 1, 1965

By R. L. Perrine

The rise of drain holes drilled from a well to improve productivity is becoming increasingly common. This paper presents data on the productivity increase that may he expected. The data were obtained by use of an electrolytic tank mode1 of a reservoir. Parameter varied in the study to show their effect on productivity include the length, number, and arrangement of drain holes, formation thickness, and damage near the well-hore. The most important results are that very large increases in productivity can be expected only ill damaged wells. The distance, to which drain holes penetrate is of primary importance. Additional length is more effective than increasing the number of drain holes. INTRODUCTI O N In planning the use of drain holes to improve productivity, it is important to he able to estimate the increase in production that can be obtained for a given expenditure. It is also important to know what combination of parameters related to the use of drain holes can he chosen to give the largest production increase. This paper presents data on the productivity increase that may be expected, as obtained by use of an electrolytic tank model of the reservoir. In this study, :! number of parameters were varied to show their effect on productivity. These included the length, number, and arrangement of the drain holes. The presence or absence of a damaged zone of low permeability around the well-bore and the thickness of the producing formation were also considered. The productivity increase that might be expected due to drain holes is presented as the ratio: productivity of a well after drain holes are drilled and completed to the productivity of the same well in an undamaged state without drain holes. The symbol Q/Qo is used to represent this productivity ratio. Thus, the comparison in each case is with a formation of uniform and undamaged permeability. Additional notation includes I;, for the radial extent of the damaged zone, which is assumed to be cylindrical and concentric with the wellbore. Thus the effect of an actual block is approximated by a discontinuous varia-tion in permeability. For purposes of this paper, the permeability within the damaged zone, denoted by kb, is assumed to be 1/25 that in the remainder of the formation, or k. A necessary assumption in making comparative tests using an electrolytic model is that reservoir flow behavior can be approximated by single-phase, steady-\tate flow according to Darey's Law. In addition, the formation must be assumed to be homogeneous with equal horizontal and vertical permeability. The well-hore diameter in this study is assumed to be 11¾ in. and the drainage radius of the well equal to 500 ft. The drain holes are considered to have been completed without damage. THE ELECTROLYTlC MODEL 'She producing formation was modeled by forming a sheet of phosphor-bronze into a cylinder 40% in, in diameter to represent the boundary of the drainage area. This was enclosed in a waterproofed plywood box, and the box filled to an appropriate level with a dilute sodium chloride solution. Solution concentration was adjusted to give a total resistance from

Jan 1, 1956

By Thomas T., Read

IT will be recalled that the first professor of metallurgy in the United States, appointed in 1855, never really gave any instruction in metallurgy and gradually turned into a professor of mineralogy. Metallurgy was included with. mining in the early curricula, two students who took the B.S. in mining engineering from the Polytechnic College of Pennsylvania in 1862 wrote their graduation theses on the metallurgy of copper and zinc, respectively. Even after Columbia School of Mines established, in 1868, a separate curriculum leading to the Ph.B. degree in metallurgy, very few students elected it,* preferring to take the mining degree, since they received in its curriculum nearly all the metallurgical instruction they would have in the metallurgical curriculum. For many years a large proportion of the men who attained prominence in metallurgical enterprises had taken mining rather than metallurgical degrees. METALLURGY Clifton Sorby's study of thin sections of rocks under the micro¬scope, beginning in 1850, and its subsequent development by Zirkel and others, had made microscopic petrography a recog¬nized department of geological research as early as 1873. . It was inevitable that the idea of studying polished metal surfaces-¬under the microscope by reflected instead of transmitted light would occur to investigators. Sorby himself did it in 1864, and Adolph Martens and Floris Osmond may -be especially named among the many European workers who, by the late eighties, had so developed the, necessary techniques that they were able to photograph polished metal surfaces at magnifications as high

Jan 1, 1941

By P. A. Beck, M. V. Nevitt

All binary and a number of ternary u alloys formed by first long period transition elements were examined and found to be ferromagnetic at low temperatures. The Curie temperatures for these alloys were measured. It was found that the correlation of the Curie temperature with composition may be described qualitatively in terms of the contributions of the various component atomic moments to the saturation moment of the alloy. Ternary Fe-Cr-Mo u phase alloys were also found to be ferromagnetic, with a Curie temperature dependent on the iron content and largely independent of the unit cell dimensions. Similar relations were found for the Co-Fe-Cr and the Co-Cr-Mo a alloys, where the Co + Fe content appears to determine the Curie temperature. RECENTLY, it has become increasingly evident that the u phase is some kind of an "electron compound." Several papers1-' discussed the empirical correlation between the composition of the various u phases in alloys of the transition elements and the distribution of electrons in the partially filled d-levels of the component atoms. However, a picture of the latter can be formed only in a more or less intuitive manner, as in the Pauling theory," and the rigorous treatment of these problems is at present prevented by lack of adequate knowledge of the electronic structure of the transition elements in the metallic state. It appeared reasonable to expect that investigation of the magnetic properties, which are related to d-shell electrons, may help in clarifying the physical nature of the foregoing empirical correlation. Qualitative tests of samples of various compositions have shown that certain u alloys become ferromagnetic at liquid nitrogen temperature." The present investigation was undertaken to determine whether or not low temperature ferromagnetism is characteristic of a large variety of u alloys and to establish how the Curie temperatures of ferromagnetic u alloys are influenced by changes in composition and in lattice parameter. In the first portion of the in- vestigation, Curie temperatures were measured for a series of u alloys containing either vanadium or chromium with one or two of the elements manganese, iron, cobalt, or nickel. In the second phase of the work, data were obtained on the Curie temperature of ternary (Fe, Co, Cr)a, (Fe, Cr, Mo)a, and (Co, Cr, MO)U alloys, as a function of composition and of interatomic spacing. Experimental Procedures High frequency vacuum melting in high purity re-crystallized alumina crucibles was employed in the preparation of the u alloys, using metals whose lot analyses are given in Table I. Approximately two-thirds of the alloys were analyzed chemically, the analytical results being in acceptable agreement with the intended compositions, as seen in Tables I1 and 111. The specimens were annealed for homogen-ization in an atmosphere of purified 92 pct He and 8 pct H, mixture or in evacuated and sealed Vycor tubes at temperatures from 780" to 1300°C, depending on the temperature range of the u phase field for the particular composition. The annealing temwerature and time for kach alloy are given in Tables 11 and 111. Curie points were determined by an induction method; the change with temperature of mutual inductance between two coils was observed when the i-u specimen was inserted into the flux path between the coils. The transformer consisted of three coils each containing 1200 turns of 0.0050 in. diam enameled copper wire. The center coil, P in Fig. 1, served as the primary coil, and was linked magnetically with each of the two secondary coils, S, and S? which were connected in series opposition. The primary coil, P, was energized by an audio-oscillator, set at a frequency of 500 cycles per sec, while the signal from the transformer secondary circuit,

Jan 1, 1956

By C. L. Mantell

Although so common and well known a metal, tin is really a less abundant element than many of those less familiar and usually ranked with the scarce or rare elements, such as cerium, yttrium, lithium, beryllium, titanium, zirconium and vanadium. The color of tin is white, with a slightly bluish tinge. When it is compared with nickel, the latter metal is brown. When placed alongside of tin, chromium is definitely blue. Tin is whiter than silver or zinc. Exceedingly thin films of tin show various shades of brown by transmitted light. The metal has a brilliant luster, and when mirror-polished, has high light reflectivity. The luster depends to a large extent upon the pouring temperature at which the metal is cast. If the temperature be too high, iridescent colors may show on the surface. These are the result of oxide film formation. If the pouring temperature be too low, the surface is dull. Small amounts of foreign metals, such as lead, arsenic, antimony and iron, decrease the luster of tin and impart a yellowish tinge to the metal. The structure is decidedly crystalline. The cast metal is a mass of crystals. When a bar of tin is bent, it emits a characteristic creaking sound. This is called the "cry" of tin, resulting from the grinding of the crystals one against the other during the bending of the metal. Tin metal may lose its crystalline structure by cold working, but grain growth occurs rapidly under the influence of heat. Metal which has been cast at a low temperature may become amorphous as the result of mechanical work. If such material be heated to temperatures well below the melting point, say at 110° C. for a half hour or for a few minutes at 150" C. recrystallization occurs. If the surface of tinned plate, tin foil, or tin meta1 in cast form be etched with hydrochloric acid containing a little free chlorine, attack occurs at the intererystalline faces. The surface shows patterns resembling the frost flowers on window panes in winter. The etched appearance is called moire metallique. Fine dendritic surface crystals of tin may be obtained by casting the metal on a surface of polished steel. In commercial tin plate, the intercrystalline boundaries are shown by fine grooves or channels, .which result from the method

Jan 1, 1929

By C. L. Mantell

Although so common and well known a metal, tin is really a less abundant element than many of those less familiar and usually ranked with the scarce or rare elements, such as cerium, yttrium, lithium, beryllium, titanium, zirconium and vanadium. The color of tin is white, with a slightly bluish tinge. When it is compared with nickel, the latter metal is brown. When placed alongside of tin, chromium is definitely blue. Tin is whiter than silver or zinc. Exceedingly thin films of tin show various shades of brown by transmitted light. The metal has a brilliant luster, and when mirror-polished, has high light reflectivity. The luster depends to a large extent upon the pouring temperature at which the metal is cast. If the temperature be too high, iridescent colors may show on the surface. These are the result of oxide film formation. If the pouring temperature be too low, the surface is dull. Small amounts of foreign metals, such as lead, arsenic, antimony and iron, decrease the luster of tin and impart a yellowish tinge to the metal. The structure is decidedly crystalline. The cast metal is a mass of crystals. When a bar of tin is bent, it emits a characteristic creaking sound. This is called the "cry" of tin, resulting from the grinding of the crystals one against the other during the bending of the metal. Tin metal may lose its crystalline structure by cold working, but grain growth occurs rapidly under the influence of heat. Metal which has been cast at a low temperature may become amorphous as the result of mechanical work. If such material be heated to temperatures well below the melting point, say at 110° C. for a half hour or for a few minutes at 150" C. recrystallization occurs. If the surface of tinned plate, tin foil, or tin meta1 in cast form be etched with hydrochloric acid containing a little free chlorine, attack occurs at the intererystalline faces. The surface shows patterns resembling the frost flowers on window panes in winter. The etched appearance is called moire metallique. Fine dendritic surface crystals of tin may be obtained by casting the metal on a surface of polished steel. In commercial tin plate, the intercrystalline boundaries are shown by fine grooves or channels, .which result from the method

Jan 1, 1929

By W. J. Joslin

The frontal-advance equation can determine how the fluid withdrawal rate and subsurface operating pressure influence oil recovery from pressure-maintained reservoirs having characteristics favorable for efficient vertical segregation. For effective vertical segregation in formations having low dip angles, the requirements are: thick, massive sands, low viscosity oil and high vertical permeability with few discontinuous shale members. This approach has been successfully applied to the LL-370, which is a massive Eocene sandstone reservoir containing crude with an average gravity of 26" APT, a dip of only 3" and vertical permeability of ½ darcy. The average gas cap saturation was calculated for various rates of vertical gas-oil contact movement corresponding to a wide range of reservoir producing rates. This method also evaluated the effect of different pressure maintenance levels on oil recovery. Applicability of this procedure for calculating the present oil saturation in the LL-370 gas cap has been substantiated from field performance, where the oil saturation was computed by comparing oil recovery with the gas cap volume vacated. INTRODUCTION During the natural depletion history of the LL-370 reservoir, located in Lake Maracaibo, Venezuela, excellent vertical segregation resulted in the formation of a thin gas zone over a substantial portion of the oil-productive area. Subsequently, gas injection forced this thin gas-saturated zone slowly downward, reducing the oil saturation in the gas cap to a low value. The oil recovery has been raised considerably above earlier predictions where vertical segregation effects were under-estimated. In order to determine the maximum efficient producing rate and optimum operating pressure for this reservoir, a vertical gas frontal-advance analysis has been made through application of the fractional flow equation. LL-370 RESERVOIR CHARACTERISTICS The reservoir consists of a truncated monocline of massive. highly-permeable Eocene sandstone, called the B-b formation, covering an area of more than 13,500 acres. The original oil in place was 2.17 billion STB. Internal non-sealing faults subdivide the structure into four blocks called the B-6-x.6, 10, 11 and 13, which are effectively bounded by major faulting on the flanks, an unconformity updip to the west, and an immobile aquifer to the southeast. The producing formation occurs at an average depth of 5,250 ft subsea and has a closure of more than 1,500 ft. A typical producing section has a net oil sand thickness of 170 ft. Scattered throughout the section are a few randomly-positioned shale lenses which increase in thickness and areal extent downdip. The reservoir rock and fluid properties vary with depth. The permeability and produced oil gravity are 1600 md and 28" API at the top, compared to 300 md and 18° API at the water-oil contact. The productivity of updip wells is, therefore, much higher than the reservoir average. The reservoir oil was originally saturated at the crest, grading to a slight degree of undersaturation at the water-oil contact. There was no original gas cap; and material balance and the field performance indicate no water influx. Except for the northern B-6-x.6 block, the fluid and rock properties have already been published.' Average LL-370 reservoir properties are shown in Table 1. RESERVOIR PERFORMANCE UNDER NATURAL DEPLETION Fig. 1 shows production performance from 1939 to date. Early development was gradual, with 30 wells pro-

Jan 1, 1965

By C. W. Spencer, J. Singer

A PARTIAL phase diagram for the As-Te system is given in Hansen.' The only compound reported is As2Te3, melting at 362°C. Stoichiometric quantities of reagent-grade elements were reacted in evacuated quartz and directionally cooled. The resulting ingot consisted of very thin threadlike crystals from which only very small single-crystal fragments were isolated. A powder diffraction diagram disclosed nonisomorphism with the analogous V-VI compounds insofar as these have been reported; Sb2S3, As2S3, Bi,S,, and Bi2Te3 data in the ASTM index of powder patterns, together with the single-crystal data on Sb2Se3,2 were used for the com- parison with the observed spacings. Single-crystal data confirmed the uniqueness of the As2Te3 structure. Single-crystal Weissenberg diagrams have so far yielded the following data: As2Te3 is monoclinic, space group C-m (OkO data still lacking), a = 14.4A, b = 4.05A, C = 9.92A, ß = 97". The cell volume is about 5802. The set of isomorphous ortho-rhombic cells of Sb2Se3, Sb2S3, and Bi2S, are apparently related to As,Te, in having one lattice constant close to 4.0 and with cell volumes as large as 540A8. Assuming Z = 4 for As2Te3 also, the density is calculated as 6.1 which agrees well with a roughly determined value of 6.0. A complete structure analysis is under way.

Jan 1, 1956

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,' involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct alloy content were carefully resolved. Phase relationships in the higher alloy content regions were outlined. A single intermediate phase, peritectically formed, of the form ZrX2 was established in each system. A eutectic and a eutectoid were found in the zirconium-rich region of both systems. Appreciable solubility of molybdenum and wolfram was found in ß zirconium, but only a slight solubility in a zirconium. PREVIOUS work on these systems was limited to X-ray investigations of the intermediate phases1, 2 and preliminary surveys of the zirconium-rich alloys." The diagrams presented were determined principally by metallographic, thermal analysis, and incipient melting techniques. In accordance with the Atomic Energy Commission contract requirements, phase relationships up to 50 atomic pct molybdenum or wolfram were carefully resolved, while only a limited amount of work was done to outline the 50 to 100 atomic pct alloy region. A description and analysis of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar, produced by the decomposition of a volatile iodide onto a hot filament, was employed for these studies. Westinghouse "Grade 3" crystal bar was used for all alloys. The zirconium, as received, was coated with corrosion product from a standard autoclave test by which its grade designation is determined. This was removed by a sand-blasting and HF-HNO, pickling technique developed by the Atomic Energy Commission. The bars were cold rolled to approximately 1/32 in. sheet, pickled for iron removal, sheared to 1/4 in. squares, washed with acetone, and stored for furnace charge. Molybdenum sheet. 0.003 in. thick, 0.001 to 0.005 in. wolfram wire, and M in. wolfram rod crushed to granular form, from Fansteel Metallurgical Corp., were used as alloying stock. Melting Procedure A nonconsumable electrode arc furnace identical to that described in detail by Hansen et al.4 was used. The source of power for melting Zr-Mo alloys was a 400 amp dc welding generator, while a 900 amp dc generator was used for preparing Zr-W alloys. Electrode tips of the same material as the alloy addition were employed in both systems, i.e., molybdenum tips were used for Zr-Mo alloys, and wolfram tips for Zr-W alloys. This precluded any possible electrode contamination during arc melting. Ingots of 20 to 30 g of Zr-Mo alloys were melted under high purity helium in the cavity of a copper block insert in a spun copper crucible. Homogeneity was insured by remelting all ingots four to six times without opening the furnace. Due to the large difference between the melting points of wolfram and zirconium, direct melting of the charged metals as above generally yielded ingots containing unmelted wolfram particles. This was overcome, after many variations in technique, by melting a pure wolfram charge at high power levels (700 to 900 amp) and slowly adding zirconium to form a master alloy. Such master alloys were sectioned and remelted several times, then crushed to serve as melting stock for alloys of lower wolfram content. Master alloys containing 26, 50, 52, 70, and

Jan 1, 1954

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By Joachim J. Hauser

William F. Hosford, Jr. (Massachusetts Institute of Technology)—Dr. Hauser has used a very interesting method to study the interaction of dislocations on different slip systems, but it should be pointed out that the analysis of the experiments is subject to a serious criticism. He states that "the effect of the compression can be adequately described by one slip system." The effect of frictional constraint during the compression makes this quite unlikely. When a block of metal is compressed its lateral expansion requires a sliding of the metal over the compression platens. The role of friction in the interface between the deforming metal and the platens is to increase the normal force required for the compression. Analyses1213 have shown that, in general, the additional force, p, required for the compression is a function of l/h where is the coefficient of friction, I is the length of the speci- men in contact with the platens. For a constant COefficient of friction, isho' shows that P should increase exponentially with pl/h for both plane strain and axially symmetric compression. For a compression specimen, Fig. 7, whose cross section perpendicular to the compression axis is a rectangle whith one dimension L, much larger than the other W, a much larger force would be required for appreciable flow parallel to L than for flow parallel to U7. Therefore lateral strain in the W direction, EW, should be much greater than the lateral strain in the L direction EL. Since L/H = 14.5 for Dr. Hauser's crystals, and since no lubrication was used, it seems questionable that appreciable lengthening of the crystals could occur. Because the theories of frictional constraint have been derived for isotropic polycrystalline materials, it was decided to make experimental measurements on a single crystal. A section 3.590 in. long was sawed from an aluminum single crystal with a square section of 0.249 in., so that L/W= 14.4. This crystal was tested in compression between dry ground steel platens. Fig. 8 shows the orientation of the crystal and the axis of compression. The face for compression was chosen so that the operation of the single-slip system which would be predicted in the absence of friction would lead to a larger strain in the length direction than in the width direction. The dimensional changes of the width and length as well as the height were measured frequently during the compression with micrometers. Width strains were calculated from the average of readings near each end and at the center. A plot of the length strain, EL, against the width strain E w is given in Fig. 9. The slope indicates that the EL amounted to only 2.5 pct of cw. Other compression tests on similar crystals with shorter lengths also showed severely limited elongation. Even for a crystal with L/W = A.0, EL was only about 26 pct of cw. Because of the frequent interruptions of the tests for dimensional measurements should have decreased the frictional constraint by allowing a reseating of the platens, even smaller elongations under continuous testing seem probable. These tests on long narrow crystals show that essentially plane strain conditions prevailed. We may assume that Dr. Hauser's crystals deformed similarly. That the compression can be described by the

Jan 1, 1962

By J. Gurland

The wmk is concerned with the estimate of the degee of continuity of a particulate phase dispersed in a matrix. The first section is a verieu: of the parameters nzeasurable by quantitative rnetallogvaphy, namely the contact area and, under certain conditions, the number of contacts between particles of one phase. In the second section, the frequency of particle contacts is related to the degee of continuity of a randomly embedded phase orz the basis of the lattice-percolation model of Hamrnersley and others. THE extent of continuity of the constituent phases may greatly influence the structure-sensitive properties of phase mixtures, particularly if the phase properties differ significantly. An example from the literature1 is shown in Fig. 1. The marked decrease of the electrical resistivity of sintered silver-alumina bodies near 25 pct by volume of silver presumably occurs because the more conductive phase changes from a discontinuous to a continuous structure. Other example of electrical- and thermal-conductivity transitions are cited by kingery In view of these observations, a knowledge and understanding of the connectivity of the microstructure may be of considerable practical importance. This study is concerned with one aspect of the genera1 problem, namely the estimate of the degree of continuity of a particulate phase dispersed in an opaque matrix. The first section reviews the parameters measurable on a polished cross section by auantitative metallography, such as the contact area and under certain conditions, the number of contacts between particles of one phase. In the second section, an attempt is made to relate the frequency of particle contacts to the degree of continuity of a randomly embedded phase. For the purpose of this discussion, the aggregate has two constituents: the particulate phase and the matrix. The latter is considered to be homogeneous. The term "particle" is used with the meaning of "grain", i.e., a minute unit of matter which is usually a single crystal of a readily distinguishable substance within the confines of a simply connected boundary. While many of the concepts which are used here to describe the structural variables characterizing the microstructure of phase mixtures are qualitative and ill-defined, they are presented with the intent of stimulating further work of a more general and rigorous nature. I) PARTICLE CONTACT, CONTIGUITY, AND MEAN FREE PATH 1) Measurement of Contiguity. The fraction of the total internal surface of a phase a shared with particles of that same phase in a two-phase mixture of and $ is indicated by the contiguity ratio:3 whereis the area of the interface between o particles, and Sap is the area of the interface between a particles and matrix P, per unit volume of mixture. The contiguity ratio ranges from 0 to 1 as the distribution of the a phase changes from a completely dispersed to a completely agglomerated structure. The interfacial areas may be obtained from simple intercept measurements on a random plane, after Smith and Guttman where and N are the numbers of intercepts between a random line of unit length on a plane of polish and the interparticle and interphase interfaces, respectively. The equations are valid for any distribution of particle sizes and shapes.

Jan 1, 1967

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941