Search Documents

J. H. HEGINBOTHAM, a, metallurgist of the General Engineering Co., talked on "Current Milling Practice at Kirkland Lake," at the December meeting of the Utah Section. The ore is enough alike through the whole district so that some generalizations and comparisons may be made. The question as to whether or not the flotation process should be used in the flowsheet for extracting gold by cyanide solutions is still being vigorously debated, and it will seemingly need some years for a definite answer to be given. Most of the gold is either free, though much of it is finely dispersed in quartz, or occurs with pyrite. At times there may be 2 per cent of telluride compounds in the ore, but the amount of gold telluride present is small and has not been definitely established. It has been shown by Dr. Haultain and others that though gold tellurides may be so finely disseminated that it is necessary to grind the ore exceedingly fine, the compounds themselves are not difficultly soluble. (An increase in temperature helps to dissolve tellurides, and also to settle pulps.) It is likely that if the ore were ground through 400 mesh, practically all of the gold would be soluble. As it is, with 96 to 98 per cent of the ore ground to minus 200 mesh, and some 70 per cent minus 325, the cost of

Jan 1, 1934

By Howard N. Eavenson

WASTE of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few ears after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained. but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested. but without any illusions that it will be followed or that much attention will be paid to it.

Jan 1, 1946

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

By James P. Kimball

AMONG the curious results of the recent advance of prices in the iron trade of the United States, one of them at least is to be regarded as of great importance. I allude to the utilization of mill cinder as a cheap and almost costless substitute for high-priced iron ores in many blast furnaces, situated within easy reach of such raw material. It has been, with but few exceptions, the practice in this country, based upon tradition rather than upon authority or European precedents, to waste this material on 'account of its high proportion of silicic and phosphoric acids, although known to contain more iron than most ores, and although also known to be sometimes applied to the blast furnace in greater or less quantities without serious detriment to the iron for specific purposes. While in use to a limited extent in the Hocking Valley and Hanging Rock iron regions of Ohio for several years, its use in Western Pennsylvania has only become general of late, under the exigencies of high prices and a short supply of ore. Especially has mill cinder largely entered into the stock of furnaces attached to rolling mills in and about Pittsburgh. Under such circumstances the cinder pig has been paddled on the premises, and the malleable iron produced has been unexpectedly good. Cautiously as at first mill cinder has been applied, it is evident that the temptation to use it freely is a strong one whenever the commercial rates for high-class ores are out of proportion to the general conditions of the iron trade, as sometimes happens in this country, especially as the free use of it is apparently justified by the quality of the iron produced from this cheap and abundant material. Indeed the consumption of cinder pig has., not been wholly confined to mills using up the production of furnaces belonging to the same plant. One furnace at least on the Ohio, at Covington, for several' months has been making foundry pig from "all cinder." The iron has gone into the general trade. It is probable that malleable iron of good quality can he made from the poorest cinder pig, but with what degree of economy will

Jan 1, 1881

By Francis A. Thomson

IN reviewing mineral industry education a year ago, occasion was taken to congratulate the Institute in general and to felicitate the Education Di- vision in particular on "the most gratifying growth which is taking place in Institute consciousness in regard to its responsibility for the recruitment and adequate training of student personnel and for the successful bridging of the difficult gap between graduation and achievement of professional status." Continuation of this growth of interest throughout 1939 is a recognition of the validity of the splendid statement of George Otis Smith that the mining students of today are the ore reserve of the Institute for the future. In this connection one recalls the equally apt expression of another distinguished geologist, George M. Fowler, who, speaking of exploration for ore deposits, says, "The place to look for elephants is where elephants have been found."

Jan 1, 1940

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By Gene D. Clayton, Robert R. Dimock

A time-consuming and expensive preshearing program to minimize the adverse effects of blasting on slope stability at Kennecott Copper Corp.'s Ruth Pit in east-central Nevada has been eliminated in favor of down-the-hole, nonelectric delayed blasting which can produce a smooth wall effect and improve blast fragmentation. The new blasting approach resulted from a Kennecott engineering investigation aimed at improving the stability of the extremely variable rock conditions found throughout the pit by reducing the vibrational energy imparted to the walls with conventional bench blasts.

Jan 4, 1977

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days' rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

By AIME AIME

THE PAPER, "Surface Effects on Assay Beads Caused by Metals of the. Platinum Group," presented by J. L. Byers, before the Institute of. Metals Division at the February meeting of the Institute, is the subject of interesting discussion, an abstract of which follows. The original paper is available at Institute headquarters as a Preprint. Member-What assurance have you that the percentage of metals, as stated, is really an accumulation?

Jan 1, 1932

By George F. Kunz

THE recently discovered occurrence of diamonds near Murfreesboro, Pike county, Ark., was brought to. our attention by Mr. Samuel W. Reyburn (Trustee for Messrs. C. S. Stifft, A. D. Cohn, August Zinsser, Jr., and himself, owners of the property), through whose courtesy we investigated the locality of the deposit. Prospecting with the diamond-drill is now in active progress ; but mining operations on a large scale have not yet been ordered. Geology.-The geology as well as the petrography of this interesting locality has been well described by Messrs. J. C. Branner and R. N. Brackett.1 Briefly summarized, the igneous rock in which the diamonds are found is a vitreous peridotite, forming a stock or volcanic neck, which has broken up through the Carboniferous and Cretaceous quartzites and sandstones. After an extensive period of erosion, during which an unknown portion of the neck and presumably a previously existent volcanic cone have been removed, the surface was covered with thin beds of Post-Tertiary conglomerate. The volcanic intrusion was accompanied by the formation of several small dikes of a rock much like that of the main body. One of these dikes cuts across the stock, while another cuts the Cretaceous sandstone, but is overlain by the conglomerate, thus giving a datum for the period of intrusion. So far as known, there was little, if any, metamorphism of the country-rock by the igneous magna, which probably followed an approximately vertical course, so that a more or less vertical extension downward of the igneous body to indefinite depths may be expected.

Mar 1, 1908

By AIME AIME

Acid Open-Hearth Manipulation.. By ANDREW MCWILLIAM and WILLIAM H. HATFIELD, ii, 279. Discussion by J. J. MORGAN, iii, 647; E. H. SANITER, iii, 648; MCWILLIAM and HATFIELD, 111, 648. ADDICKS, LAWRENCE. The Effect of Impurities on the Electrical Conductivity of Copper, iii, 559. Address of Welcome to the U. S. National Museum, Washington, D. C. By RICHARD RATHBUN, .iv, 923. ALLDERDICE, TAYLOR. Discussion of MR. ROE'S paper, The Mann¬ facture and Characteristics of Wrought Iron, v, 1091. American Mining Engineer. Discussion by ARTHUR JARMAN, iii, 641. An Automatic Stock-Line Recorder for Iron Blast-Furnaces. By J. E. JOHNSON, JR., iii, 509. Anthracite-Washeries. By GEORGE W. HARRIS, vi, 1263.

Jan 1, 1907

By IRVING H. WENTIVORTII

(New York Meeting, February, 1912.) THE little town of San Nicolás, Tamaulipas, Mexico, lies approximately 60 miles east of Linares, situated in the State of Nuevo Leon, and 150 miles SE. of Monterey, as shown in the sketch-map. Fig. 1. The place is reached from Monterey by the Tampico train as far as Linares, a distance of 92 miles, and then by coach the rest of the way. It is situated in a narrow valley between low hills, the houses forming one main street and a plaza. It is peopled by about 500 inhabitants. The climate is temperate, the thermometer ranging from 90° in summer to a few degrees below freezing-point in winter; but this severe weather only lasts a day or two at a time, when the " northers " blow. There are no streams in the vicinity, but water sufficient for the use of the people is obtained from wells. The rainfall is about the same as that in the rest of NE. Mexico. The rainy months are July, August, and September. The rest of the year is practically dry, with an occasional showery day or two during the winter, when a " norther " is blowing. Timber is abundant in many localities. There are two varieties of oak, besides mesquite, ebony, "maguira," "patol," and a number of other kinds of trees indigenous to this region. I. HISTORY. On the discovery of the silver-lead hearing veins occurring in this district, the mining-camp of San Nicolás was founded in 1767 by the Spaniards, and numerous mines were opened and worked for a distance of abort 3 miles east and 5 miles west of the town. At the western extremity and near the Carrolena mine, a small town called San Pedro was built. The ruined walls of the houses form a single street, and all is over-

Aug 1, 1912

By HOMER L. WILLIAMS

WHILE some of the mining companies have been pumping a small amount of water for some time, it is only in recent years that large quantities of water have been encountered in the Tonopah district. The water appears to be in different zones or belts so that the draining of one property does not necessarily affect the one adjoining. Consequently, each company has its own pumping plant and its own conditions. The companies panes handling the largest amount of water are the Tonopah Extension Mining Co., Halifax Tonopah Mining Co., West Tonopah Consolidated Mining Co., and Great Western Consolidated Mining Co. The Halifax shaft is on the eastern end of the district and the other three properties on the western. The ore-bearing formation occurs at greater depth on -the eastern and western ends, hence the water problem in these properties.

Jan 1, 1921

By J. Brian Eby

As is generally understood, the word geophysics means literally ?the physics of the Earth? and the science of geophysics is therefore that which treats of the study and measurements of the various physical properties of the Earth. The broad and general study of the elastic, the gravimetric. or the magnetic properties of the Earth as a whole belongs to the general science of geophysics. The detailed application of this science to rocks of shallow depth and in small areas for the purposes of ascertaining data on their character and structural attitude gave rise to the present well-known science of ?applied geophysics.? Since the discovery of enormous new quantities of oil, gas, and sulphur has been by far and wide the principal benefaction of geo-physics in the United States, this paper will refer only to geophysical methods employed in the search for these particular minerals. The application of methods and appliances originally used for geophysical research to the solution of the practical problems of finding new oil-fields, plus the counterflow or new and highly refined techniques and Instruments from the company and consulting geophysical research laboratories and into non-economic geophysical research, has provided another case of that gen-eral cycle of events which is familiar to all scientists. That this closed-circuit flow or scientific current has been tremendously important to the whole science of geophysics is probably well known to all members of this audience, but the gen-eral status of the exploratory geophysical arts as now used In the search for new oil-fields, the scales on which different methods are being used, the magnitude of the costs involved, and the far greater magnitude of the practical results achieved may not necessarily have come so directly to your attention. It is, I understand, for this reason that this paper has been sug-gested, and I shall seek to provide the information requested by using as case-illustrations those changes in the oil-reserve picture for the United States as a whole, and for the Gulf Coast, California, and Illinois Basin regions in particular, which have occurred in the period of the past 17 years, during which time oil-field discoveries have proceeded at a rate which served to build up known and readily-available (or proven) oil supplies to a reasonable figure, and have dispelled the fears of a serious oil shortage during any period for which valid fore-casts can be made. Not that geophysical-prospecting methods have alone been responsible for this transformation, but they have an indispensable and leading part in the picture of exploration and production-to which geophysics, geology, engineering, and general technical progress have jointly made contribution. So far as the United States as a whole is concerned, its total proven, probable, and possible oil reserves (discoverable and recoverable by then-known methods) were estimated at about nine billion barrels in 1920, whereas proven reserves alone are now com-puted at about 16 billion. In 1920 the driller in ?wild-cat? territory was faced with the knowledge that for every new oil-field opened by a successful well, from 20 to 100 unsuccessful wells would have to be drilled and, in some territories, that the chances for a discovery were really less than one in 100 for new drilling, in contrast to which may be cited the record for the past year in parts of Louisiana where the 67 wells drilled opened 16 new oil-fields, that is to say, where the score of hits to misses was increased to approximately one out of four.

Jan 1, 1940

AlFred JamEs," London, Eug.:—I thank you, gentlemen, for Sour kind invitation to address you. It is a very great pleasure for me to be here at your annual meeting, and, although I have been a member since 1894, this is the first opportunity I have

Jan 1, 1909

By D. C. Porterfield

ProUuction of crude oil in Venezuela increased from 186,134,000 bbl. in 1940 to 2~8,131,ooo bbl. in 1941, or 22.6 per cent, to establish a new all-time high for the country. While the average production for the year was 625,000 bbl. per day, production during the month of December 1941 averaged 751,000 bbl. per day, and during the last week of the year, 766,000 bbl. per day. Production from the Lake Maracaibo basin averaged 454,000 bbl. per day during the year, or 72 per cent of the total for the country, compared with 73 per cent of the total produced in 1940. Drilling during the year was approximately on the same scale as in 1940, with 438 wells completed in 1941 as compared with 429 the year before. Exploratory completions decreased from 18 in 1940 to 6 in 1941. Of the drilling operations in 1941, 56 per cent was concentrated in the Lake Maracaibo basin and 44 per cent in eastern Venezuela, success being 98 per cent in the Lake basin and 83 per cent in the east. Successful completions for the country as a whole amounted to 92 per cent of the total wells drilled. Exploratory drilling in 1941 resulted in the discovery of three new fields, all in eastern Venezuela; viz., Guara, about II km. to the northeast of the Oficina field but on a separate structure; Santa Rosa, which is east of El Roble field on a structure forming a part of the major Santa -Ana- San Joaquin-El Roble uplift; and Santa Barbara, which is southwest of the Jusepin field on an extension of the main Jusepin anticline. At the close of the year three wildcats were drilling, all of which showed prospects of obtaining production; that is, Mercedes No, 2 in central Guarico, Las Ollas No. I on the Anzoategui-Guarico border near the town of Zaraza, and Quiamare No. I in Anzoategui northeast of the town of San Mateo. In spite of heavy withdrawals and the resultant natural decline in the potentials of older producing areas, new drilling during the year increased the potential production of the country from an estimated 780,000 bbl. per day at the end of 1940 to an estimated 810,000 bbl. per day at the end of 1941, or approximately 4 per cent. Since domestic consumption of petroleum products is insignificant compared with total production, exports of crude and products during the year increased in line with production. Crude exports totaled 196,800,000 bbl., compared with 158,400,-000 bbl. in 1940, and exports of products were 26,100,000 bbl., compared with 21,900,000 bbl. the year before. Exports of crude from Venezuela to the United States amounted to 36,500,000 bbl. In addition, about 2,200,000 bbl. was imported in bond into the United States for transfer to Canada. Total refining capacity of the country in 1941 was approximately 125,000 bbl. per day, including a crude-conversion plant with a capacity of 32,000 bbl. per day, capable of making fuel oil only. Three plants with a capacity of 121,000 bbl. Per

Jan 1, 1945

By M. King Hubbert

In 1856 Henry Darcy described in an appendix to his book, Les Fontaines Publiques de la Ville de Dijon, a series of experiments on the downward flow of water through filter sands, whereby it was established that the rate of flow is given by the equation: q= - K(h2- h2)/I1 in which q is the volume of water crossing unit area in unit time, I is the thickness of the sand, h1 and h2 the heights above a reference level of the water in manometers terminated above and below the sand, respectively, and K a factor of proportionality. This relationship, appropriately, soon became known as Darcy's law. Subsequently many separate attempts have been made to give Darcy's empirical expression a more general physical fornzulation, with the result that .so many mutually inconsistent expressions of what is purported to he Darcy's law have appeared in published literature that sight has often been lost of Darcy's own work and of its significance. In the present paper, therefore, it shall be our purpose to reinform ourselves upon what Darcy himself did, and then to determine the meaning of his results when expressed explicitly in terms of the pertinent physical variables involved. This will be done first by the empirical method used by Darcy himself, and then by direct derivation from the Navier-Stokes equation of motion of viscous fluids. We find in this manner that: q = (N4(p/p)[g - (l/p) gradPI = WE, is a physical expression for Darcy's law, which is valid for liquids generally, and for gases at pressures higher than about 20 atmospheres. Here N is a shape factor and d a characteristic length of the pore structure of the solid, p and IL are the density and viscosity of the fluid, a = (Nd2)(pip) is the volume conductivity of the system, and E = [g - (l/p) grad p] is the impelling force per unit mass acting upon the fluid. It is found also that Darcy's law is valid only for flow velocities such that the inertial forces are negligible as compared with those arising from viscosity. In general, three-dimensional space there exist two superposed physical fields: a field of force of charucteristic vector E, and a field of flow of vector q. The force field is more general than the flow field since it has values in all space capable of being occupied by the fluid. So long as the fluid density is constant or is a function of the pressure only, curl E = 0, E = - grad F where F = gz + dp/p The field of flow, independently of the force field, must satisfy the conservation of mom, leading to the equation of continuity div pq = — f ap/at , where f is the porosity, und t is the time. For steady rnotion ap/at = 0. and div pq = 0 .

Jan 1, 1957

By R. Kossowsky

Structural changes in Be-Cu, Be-Ni. Be - Ag, and Be-Fc alloys pressurized in a solid medium were invesligated by resistivity measurements , X-ray diffrac lion in situ and metallogvaphic examination. Some limited tests in liquid medium were also conducted. Good correlation was oblained between diauges of slope of relative resistance us pressure and changes in diffraction pattern. Metallographic examination rez:ealed that the copper, silver, and nickel alloys lwiu heauily due to the applicalion of pressure at room temperature. Using polarized light technique {1012}, {1011}, and possible {1010} twinning planes were identified. At eleuated temperature twinning was moslly confined to the {1012} planes. Although twin-ning could be promoted by application of hydroslutic pvessure (liquid medium), it was strongly enhanced by the pvesence of a nonhydvostatic shear component due to pressurizalion in a solid medium. It was further obserced that a decrease in grain size inlnibiled twinnitzg activily. A great deal of effort has been expended in recent years to render beryllium useful for structural applications. Efforts were concentrated towards a possible phase change and to promoting other than basal deformation modes. Quenching experiments to obtain the high-temperature bcc phase have failed,' nor were alloying additions successful in improving ductility of the brittle hcp phase.2 Herman et a1.3 have reported a new {1011} twinning mode in a Be-4.4 wt pct Cu alloy oriented for a C axis compression sustaining loads to 440,000 psi. A new approach using high-pressure techniques was undertaken at Curtiss-Wright, Wright Aeronautical Division Laboratories. Marder4 reported a 25 pct decrease in relative resistance of commercially pure beryllium at 92 kbar. He proposed that this discontinuity corresponded to the bcc phase found at high temperature; however, X-ray diffraction in silu did not confirm a phase transition.5 contre6 has recently shown that the bcc transition in pure beryllium is lowered to 800°C at 80 kbar accompanied by a 50 pct increase in relative resistance. The purpose of this paper is to report on one phase of an investigation of the effects of high pressures and temperatures in beryllium alloys, namely, twinning behavior in Be-Ni, Be-Cu, Be-Fe, and Be-Ag alloys pressurized to nearly 100 kbar and temperatures up to 200°C. EXPERIMENTAL METHODS Material was obtained from Nuclear Metals, Inc., in the form of a 1.5-mm-diam wire extruded in stainless-steel cladding at 1600° F. Nominal composition of the alloys is listed in Table I, and the major impurities are are given in Table 11. Pressures to 100 kbar* were ob- tained using a National Bureau of Standards type 100/400 ton tetrahedral unit supplied by Barogenics, Inc. This type of apparatus contains a retaining sleeve with a conically tapered internal surface and four pressure-intensifying anvil assemblies with tungsten carbide tips. The 10-mm-long specimen fits into a pyro-

Jan 1, 1968

The following list of corrections has been compiled from the thirty-five volumes, with some additions: VOLUME I. Page 160. The first two sentences of the second paragraph should read as follows : " For No. II we find that 2.33 percent. A1,08 take 4.07 per cent. 8109, leaving 3.48 per cent. 8102 free, which requires 3.25 per cent. CaO." Page 160, line 14, 3.79 should be 3.25; and in the 15th and 18th lines, 48.44 should be 46.98. VOLUME VI. Page 59. The discharges of the miners' inch per second, given as .2624 and .2499 cubic feet, should be .02624 and .02499, respectively. The discharges per minute, hour, etc., are correctly given. VOLUME VIII. Page 214. 16th and 25th lines, ferric carbonate should be ferrous carbonate. Page 486, 16th line, 10,000 should be 5,000. [ ]

Jan 1, 1907

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared for these tests by high-temperature methods, especially by crystallization from borax melts.

Jan 1, 1950