Search Documents

By A. E. Jenkins, L. A. Baker, N. A. Warner

Rates oj decarburization of levilated Fe-C droplets conlaining 5.5 to 0 pct C have been measured at 1660°C. Gas mixtures of 1, 10, and 100 pct 0, with helium diluenl were used at velocities of 12.5 and 62.5 cm per sec. Rates were independent of carbon concentration in the mell and in good agreement with the calculated rule of oxygen diffusion through the gas boundary layer. The effects of flow rale and total pressure are as predicled and the rates are approxitnalely 2.5 times those with CO2 as oxidant. The mass-transfer correlation used incorporaled the efject of natural convection as well as forced conrection. Graphile spheres are shown to oxidize at the same rate as Fe-C droplets under the same experimental codlions. It is concluded that, for high carbon concentrations in the melt, the rate of- decarburizalion is controlled wholly by the rate of gaseous diffusion. Rate measurements with pure CO, are reported for low carbon concentrations where CO bubbles nucleate within the droplet. Under these circumstances the decarburi-zation decreased with carbon concentration and it is proposed that carbon diffusion is significant in conlrolling the decnvburization rate. In an earlier paper1 decarburization rate measurements were reported for levitated Fe-C alloys at 1660°C but with CO2 as the oxidant. The decarburization rate was found to be independent of carbon concentration in the melt but slightly affected by total pressure. The authors were unable to explain the slight pressure effect but in all other respects the results were consistent with control by diffusion in the gas boundary layer. Subsequent work has been directed at finding the reason for the slight pressure effect and whether the kinetics with oxygen as oxidant parallel those with CO2. Recently Ito and Sano2 have shown that with water vapor-argon atmospheres the decarburization rate is gaseous diffusion controlled until an oxide film appears on the surface. In this work the melts were contained in crucibles. MASS TRANSFER IN THE GAS PHASE In the earlier analysis1 only forced-convection mass transfer was considered. Subsequent recognition of the existence of some free-convection mass transfer explained the observed small effect of total pressure on the decarburization rate. Steinberger and Treybal3 and Kinard, Manning, and Manning4 have developed correlations involving the linear addition of the contribution of radial diffusion, free and forced convection. Steinberger and Treybal&apos;s correlation was chosen as the most applicable to the present work since it correlated most of the data available in the literature and handled the low Reynolds number region exceptionally well. The correlation for (Gr&apos;Sc) < 108 is where Nu&apos; is the Nusselt number for mass transfer based upon the total surface of a sphere in an infinite medium, G&apos; is the mean Grashof number for mass transfer defined by Eq. [2], Sc is the Schmidt number (µ/pDAB)f, Re is the sphere Reynolds number (dpu,pf/µf), p is the viscosity of the gas (poise), p is the density of the gas (g cm-3), Dab is the binary diffusivity for the system A-B (sq cm sec-&apos;), dp is the sphere diameter (cm), u is the approach velocity of the gas (cm sec-I), and subscript f denotes the property value is computed at the film temperature Tf defined by Tf = +1/2(To + Tr) where To is the specimen temperature and T, is the approach gas temperature (oK). Natural convection occurs when inhomogeneities exist in gas density. These may be caused by concentration gradients, temperature gradients, or both. In the present work the temperature gradient between the sphere and the bulk gas was very large and in some cases, for example the runs with pure oxygen, the concentration gradient was also appreciable. The Grashof number defined by Mathers, Madden, and piret5 was used since it took account of both temperature and concentration gradients: where Gr&apos; is the Grashof number for mass transfer (p2fgd3|-yA-yA|/µ2f), Gr is the Grashof number for heat transfer (p2f gd3p|To - T,]/µ2fTf), Pr is the Prandtl number (cpµ/k)f, g is the acceleration due to gravity (cm sec-&apos;f, a is the concentration densification coefficient (1/p)(ap/ayA)T, yA is the mole fraction of component A at the gas-metal interface, yA is the mole fraction of component A in the bulk gas stream, cp is the heat capacity of the gas per unit mass at constant pressure (cal g-I OK-&apos;), and k is the thermal conductivity of the gas (cal cm-&apos; sec-1 OK-1). Mathers et al. tested this combined Grashof number

Jan 1, 1968

By Robert Linton

SPECIFICATIONS for clays serving raw materials in the ceramic industry usually contain the following items: (1) Chemical analysis, sometimes with mineralogical structure determined by microscopic investigation. (2) Maturing temperature and firing range, usually expressed in terms of pyrometric cone equivalent. (3) Shrinkage (drying and firing shrinkage separately). (4) Degree of plasticity. (5) Color after firing. Clays may be classified, according to the purpose of the classification, in several different ways, based on (1) Geological occurrence-transported, altered An place, indurated (shales). (2) Physical properties-plastic (bonding clays, ball clays) and nonplastic (flint clays, kaolins or china clays, bone clays). (3) Color. (4) Use. A common classification of clays for commercial designation, and one fol-

Jan 1, 1936

By John V. Beall

Cutting costs and increasing safety with new ideas is the byword with The Cleveland-Cliffs Iron Co. on the Marquette Range in Michigan. Among the new ideas being tried out are mechanical shaft mucking, prefabricated lagging to replace timber poles, Carset bits in shaft sinking, and rubber tired guide wheels on the ore skips. Plans are being made to stockpile ore with conveyor belts during the winter. In sinking the Mather "B" Shaft a 3/8-yd clamshell-type bucket is used for mucking. The clamshell is opened and closed by means of a verticallymounted hydraulic ram actuated by 5000 psi oil pressure. An Ingersoll Rand-type hoist is used to raise and lower the clamshell. The hoist is controlled by one member of the crew on the floor of the shaft. When the bucket is raised, the men swing it over the muck pile to the desired position and then it is lowered on to the broken rock. The 1400-lb weight of the bucket causes it to sink into the broken rock and it digs as the ram closes the bucket. The hydraulic ram is operated by a man on the lowest shaft steel set who controls a specially designed oil pump which supplies oil pressure. The clamshell is emptied.

Jan 1, 1949

By John V. Beall

Tsumeb has added a chapter to its absorbing history with the beginning of copper smelting operations this month. This development will be followed shortly by another one when lead smelting and refining plants go on the line next year. In our own milieu these events would be common- place enough (although a new lead smelter certainly would be cause for wonder), but in the sparsely settled remote regions of northern South West Africa they are a dramatic industrial expansion. They are also, however, a sound businesslike extension of policies which have marked the tenure of Tsumeb Corp. Ltd. The historical data given in Table I are a drab listing of factual bones without the corporeal splendor which should surround the denouement of the Tsumeb bonanza. When Sir Francis Galton traversed the country, his was an expedition which was in keeping with the then blooming era of heroic explorations. The Otavi highlands in the interior were unexplored and the reception of the natives uncertain. While the exploratory work was in progress during the turn of the century the Hottentots and Hereros were successively in open bloody rebellion. The suppression of these uprisings, particularly the Hereros, by German soldiers so decimated the tribes that a labor shortage ensued for many years, hampering the development of the colony. To these troubles may be added difficulties In obtaining mining supplies. However, there should have been no shortage of meat from wild game judging by conditions prevailing even today.

Jan 12, 1962

By J. H. Nead, T. S. Washburn

The grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure— killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes arc not present. Also, the rimmed ingot has no well defined pipe, as compared to the deep pipe on the killed ingots, and there are numerous primary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differentiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7—as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined [or deep as in the killed ingot of Fig. 1. In killed ingots, primary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By George W. Powel

IN the nation&apos;s effort to raise its magnesium metal supply to meet the ever increasing demand, the Government is relying not only on standard established practice but has extended its support to developments not so well proved-at least, not commercially proved. Within the past few months considerable progress has been made, not only in the definite output of metal but in the exploitation of new processes, the successful adaptation of which should, in a reasonably short time, assure an adequate supply of magnesium. Recent months have also witnessed a reshuffling of the favored methods as well as of the likely raw materials, with the mineral dolomite gaining in interest over its richer but less abundant competitor, magnesite, while the lowly sea water appears to be losing ground to the higher magnesian brines of Michigan and western Texas. Every month sees a new alignment and there are signs that still newer methods or raw materials will be in use before the industry finally stabilizes itself.

Jan 1, 1942

By A. W. Gauger

WITHOUT QUESTION the Commonwealth of Pennsylvania contains the most remarkable coal deposits of the whole world. Within its borders ,are to be found excellent coals ranging in rank from the high volatile bituminous of the western part of &apos;the state through the low volatile or semi-bituminous of central Pennsylvania to that aristocrat of solid fuels, anthracite, found in the East. . . . But while other states and even the Federa1 Government have recognized the needs of the coal industry, Pennsylvania has not. Though bituminous coal represents one of the most important industries in the state, far more important in annual productive wealth than agriculture, for example, hundreds, of thousands of dollars have been spent on agricultural research whereas little or nothing has been spent on coal investigation.

Jan 1, 1932

By AIME AIME

ALTHOUGH the present economic depression is felt in the petroleum industry, probably as much as in any other branch of American industry, the Petroleum Section of the Institute was well represented at the general sessions on Monday and at all of the seven division sessions on Tuesday, Wednesday and Thursday. The seven sessions of the Division were so arranged as not to conflict and thus permitted members to hear the programs of all sessions.* The first meeting of the Petroleum Division was held on Tuesday afternoon; a joint session on engineering research and production engineering. The following papers were presented:

Jan 1, 1931

P. L. Pratt (University of Birmingham, Birmingham, England)—The author has measured the hardening effect of isolated edge and screw dislocation boundaries in a remarkably elegant manner, and he proposes that the detailed structure of the boundary determines its effectiveness as a barrier to slip although "there are still unknown details of the distribution which may be extremely important." On p. 678 the author states "that for a good crystal (one having a yield of about 30 psi) a change in annealing temperature from 300" to 400 °C resulted in a negligible shift in the level of the stress-strain curve." Is this in agreement with the results of the earlier paper by Li, Washburn, and Parker8 in which such a change of temperature produced notable hardening in crystals with a yield of about 30 psi? Or were these earlier crystals, of the same nominal purity, less perfect than those used in this work? The experiment illustrated in Fig. 15, p. 681, shows that the boundary has sharpened after annealing at 400 °C, the temperature at which the hardening effect first becomes apparent. Did the author verify that no sharpening of the boundary occurred at, say, 300 °C where no hardening was found? This would seem to be an important check on the proposed mechanism, especially since zinc of this purity should polygonize at temperatures well below 400 °C within the annealing times used here. There seem to be at least two alternative explanations which could fit these facts: 1—The boundary may sharpen at 300 °C or even lower temperatures but be unable to contribute greatly to the hardening until jogged by thermal vacancies and other impurity atoms after 400 °C anneal. This mechan- ism, discussed in the earlier paper,&apos; is believed to account for the thermal hardening observed by Blank&apos;" in NaCl, as stated elsewhere: and by results from recent experiments which tend to confirm this view. 2—The dislocations in the diffuse boundary may be locked by impurity atoms at 300 °C and thus only sharpen the boundary at 400 °C with the aid of thermal vacancies. In this case it would be difficult to distinguish between the two sources of hardening (sharpening or jogging), using metal of this purity. Jack Washburn (author&apos;s reply)—The author wishes to thank Dr. Pratt for his discussion. In connection with his first comment, it should be pointed out that the temperature of testing in the present series of experiments was —196°C, whereas, in the earlier experiments he referred to,&apos; it was 20°C. Therefore, the yield values should not be directly compared. It is likely that the crystals used in the present work were initially more perfect macroscopically than the large shear specimens used previously. The small size of the test section in the kink specimens made it possible to select regions of the large crystals, from which they were acid-cut, that were free of observable small angle boundaries. The sharpening of a microscopically diffuse boundary such as that in Fig. 15 begins in zinc of this purity well below 300°C. However, it is probably not justified to conclude that because a boundary looks sharp under the microscope it has attained the ideal structure. The author agrees with Dr. Pratt that jogging of dislocation lines is one of the structural features of a small angle boundary that should be important in determining its strengthening effect. More detailed information concerning the changes in boundary structure as a

Jan 1, 1956

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

INTRODUCTION This chapter summarizes characteristics of porphyry copper deposits within the Cordilleran orogen east of the Coast Range plutonic complex of the Yukon and British Columbia and south to the Columbia River plateau and the Idaho batholith. Porphyry copper deposits in this area reflect a geologic environment different from that found for mineralized intrusions elsewhere in the Cordilleran orogen, both to the south in the United States and Mexico and to the west in Alaska. A section on the Tertiary Cascade porphyry copper province is included herein. The Cascade province is considered separately because its deposits display a unique mineralogy and age of mineralization. That portion of the Cordilleran orogen described in this chapter is shown in Fig. 32, with the Cascades shown in Fig. 39 (see p. 114). The regional geology of this area has been described by Monger, et al. (1972), Hollister (1974), Wolfhard and Ney (1974), Field, et al. (1974), and Stacey (1974). Each offer slightly differing views on the post-Mississippian evolution of the geology in this porphyry copper province. The descriptive geology in this chapter has benefited from many discussions with J. E. Armstrong and J. W. H. Monger. Two separate petrologic models have been used popularly to categorize porphyry copper deposits in this area, a diorite and a quartz monzonite model. The diorite model, which involves a mineralized quartz-free pluton, has also been called the alkalic type (CZM Special Volume 15, 1976, and Soregaroli, 1975) and the syenite suite (Sutherland Brown, et al., 1971). The quartz monzonite model has also been named the calcalkalic type (CZM Special Volume 15, 1976) and includes mineralized quartz-bearing plutons compositionally ranging from quartz diorite to granite, with the igneous phase closest to ore in time and space commonly being quartz monzonite.

Jan 1, 1978

By S. F. Emmons

The first paper which appears in the published Transactions of our Institute is that read by our respected Secretary at its first meeting in Wilkes-Barre in May, 1871. It is entitled " The Geographical Distribution of Mining Districts in the United States," and presents a brief but masterly review of what was known of the distribution of our deposits of useful minerals, particularly the metals, not only from a geographical but from a geological stand-point. At the request of Dr. Raymond I agreed, somewhat hastily, perhaps, to write for this occasion a brief sketch of the geological distribution of the deposits of the useful metals in this country, in the light of the increased knowledge of the present day. In the time given no personal investigation was possible, and as it was therefore out of the question to attempt to make anything that could be considered an original contribution to the history of our ore-deposits, I have been obliged to limit myself to an examination of such pub-

Jan 1, 1894

Jan 1, 1924

Jan 1, 1924

By V. S. Swaminathan

This year, Great Britain is looking back over a century to August 14, 1850, the day when the first "Act for the Inspection of Coal Mines" was passed in that country, an act which signaled the end of over two hundred years of hitherto uncontrolled and dangerous mining practices. It was back in the time of Queen Elizabeth that . thousands of pounds were invested in mining, particularly coal mining in England and Scot- land. By 1640 there were collieries producing 10,000 to 25,000 tons of coal per year. In the seventeenth century the Tyne district coal industry was organized into powerful partnerships, and coal took an even larger part in industry, as a source of power and as fuel for the iron industry. In the early 19th century a "phenomenal, almost devastating expansion" characterized Britain&apos;s coal industry, and it was sparked by a 111 pct in- crease in the population of England and Wales in the first half of the century. Coal production for those 50 years increased 470 pct and pig iron production was up 946 pct for the period 1801-51.

Jan 1, 1950

By Butler, P. B.

TRIPOLI is a rather unusual form of silica, which thus far has been found in commercially valuable quantities only in the neighborhood of Seneca, Mo., although there are numerous deposits of somewhat similar materials in several southern states. The latter have not, however, attained any position of real importance, due undoubtedly to definite structural limitations which have rendered them less suitable for the particular uses that have given tripoli its principal outlets. Raymond B. Ladoo, mineral technologist, says&apos;: "Since that time (1880-90) the term tripoli has with increasing definiteness been reserved for the Seneca material, and other siliceous materials of similar origin and physical properties."

Jan 1, 1928

By F. C. NINNIS

AT THE Belmont mill, the pregnant solution is de¬livered to a 30 by 10-ft. tank, from which it is pumped to three Merrill clarifying presses of the sluice-bar type, whence it flows through the meter to the precipitation supply tank. ?The solution for precipitation is pumped by a 10 by 10-in. Aldrich triplex pump and delivered through a 6-in. line to the forty-eight triangular frame Merrill presses at the head of the mill. Zinc dust is fed in at the pump suction and the solution precipitated to 0.01 to 0.02 oz. silver. The solution flowing from the presses is tested at 1-hr. intervals with sodium sulfide. All solution is precipitated to the same value; 4J tons of solution are precipitated for each ton of ore treated and the presses are cleaned every 15 days. The product from the presses&apos; is dumped into steel cars having steam-jacketed bottoms, in which they are dried until the moisture content is between 15 and 17 per cent. when 8. per cent. of soda and .3 per cent. of borax are added and the contents thoroughly mixed. In the case of special clean-ups, the precipitate is tested and the flux is added to meet the requirements.

Jan 1, 1921

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts&apos; Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts&apos; method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts&apos; law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,&apos;4, &apos;6 Fe-Cu,&apos;6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 &apos;77 187 19>2° Fe-Sn,16 and Fe-v.51 &apos;3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By G. R. Speich, L. Zwell, H. A. Wriedt

HORNBOGEN1 has recently shown that it is possible to measure the degree of segregation accompanying cellular precipitation in ferritic Fe-Zn alloys by measuring the lattice parameter of the ferrite phase within the cell. In extending this work to study a wider range of composition and to evaluate the free-energy change accompanying the growth of the cells, the lattice parameter and the boundary of the a! phase in Fe-Zn alloys were redetermined to check the earlier work of Schramm.2 This appeared to be necessary since the Fe-Zn diagram has been drastically revised since the work of Schramm. Stadelmaier and Bridgers3 have recently shown that, contrary to prior belief: the y iron field is closed and the a phase boundary extends to an a + T + L peritectic at 782°C where peritectic a contains 42 at, pet Zn. The phase T in equilibrium with the a solid solution has a composition near Fe3Zn10 and a cubic 081 type structure.&apos; The alloys were prepared by two different methods. In the first method carbonyl iron powder (400 mesh, 99.8 pet pure) and high-purity zinc powder (200 mesh, 99.99 pet pure) were mixed in a ball mill and then pressed in a die at 40,000 psi pressure to make compacts with a diameter of 5/8 in. and a thickness of l/4 in. These were sealed in evacuated quartz capsules, gradually heated to 1100°C over a period of 1 week (3 days at 600°C) 3 days at 800°C, 1 day at (1100°C), and then quenched in iced brine. For the alloys containing 23.4 and 30.1 at. pet Zn, the final homogenization anneals were performed at 1000" and 850°C) respectively, to prevent melting. In the second method, alloys were prepared by saturating high-purity iron millings (0.001 in. thick, 99.9 pet pure) in zinc vapor. For each alloy the impregnation was conducted at a fixed vapor pressure of zinc and a fixed temperature between 750&apos; and 800°C. When saturated, the millings were quenched in water. The compositions of the alloys prepared by both methods are shown in Table I. The lattice parameters of the ferritic solid solutions were determined by comparing the 26 values of their 310, peaks (using Co Ka) or of their 211 , peaks (using Cr Ka) with those of corresponding peaks for high-purity a iron. The 20 values were measured at room temperature with an X-ray dif-fractometer (G.E.-XRD5). By using a fiducial value of 2.8664Å for the lattice parameter of pure a iron at 25oC,5 the lattice parameters of the zinc-bearing

Jan 1, 1964

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947