Search Documents

By Ellsworth Daggett

THE system of pitwork used with the Cornish pumping engine, and which, for want of a better name, we may call the Cornish system of pitwork, consists essentially of a series of plunger-pumps, situated one below the other, in a shaft or incline, the plungers being operated by a rod called the pitman or pump-rod, which must, therefore, extend from the motor at the surface to the lowest pump. The subject will be best understood by reference to Fig. 1, in which k may be taken as typical of the ordinary plunger-pump, in which S is the suction pipe, u, the lower valve situated in the H piece T; v, the upper valve situated in the valve-box O; I, the mounting-pipe or column through which the water is carried to the surface; L, the plunger-barrel, and P, the plunger working through the stuffing-box, and actuated by the branch rod r, which is attached to the main pump-rod, R. The action of the pump is as follows : On the ascent of the plunger, acting now by suction, the water flows from the reservoir through the valve u, into the barrel, L. On the descent of the plunger, the water is forced up through the valve, v, which acts merely as a check valve, into the pipe, I, through which it is, at each successive down-stroke of the plunger, forced upward until it reaches the next reservoir, from which it is taken by another similar pump, and so on until it reaches the surface or drain-tunnel. The pump is obviously only single-acting, i. e., it acts only during one-half of its entire stroke. The weight of water raised during the up-stroke of the plunger is equal to the weight of a column of water whose base is the area of the plunger and whose height is the mean distance between the plunger-face and the surface of water in the lower reservoir, a distance not usually exceeding 12 or 15 feet, and which obviously cannot under the most favorable circumstances, exceed 25 or 30 feet. The water forced up during the down-stroke is equal to the weight of a column of water whose base equals the area of the plunger and whose height equals the length of the mounting column above the mean position of the plunger-face, say from 150 to 300 feet. Almost all of the useful work, therefore, is done on the de-

Jan 1, 1879

By Ellsworth Daggett

Jan 1, 1879

By CHARLES M. SCHWAB

THE ENGINEERS have placed this great country of ours in a preeminent position with everything pertaining to manufacture, metallurgy, and the kindred arts. We are second to none in the world. We have a country which, another speaker has said, God has endowed with such riches in coal and natural resources as no other country in the world. But rich as these are, there is one thing greater; the sturdy character, energy, and integrity of its people, which will make these great resources an influence in the world's developments. Great as are these resources and the energy and integrity of our people, there is one problem of our .engineering, which I term human engineering, that is of far more importance than the creation of machines and methods, with which you have been so successful in the past. Of what value is the skillfully devised machinery, the complex process, unless manned and operated by people whose heart and soul are in sympathy with the work they are doing and who have before them the giving of a complete day's work for a day's pay?

Jan 1, 1920

By D. B. RUSHNORE, K. A. Pauly

Bulletin. No. 41, May, 1910. ABBREVIATIONS. Al. Ind., Alliance Industrielle. am. Elec'n.. . American. Electrician. Bull. As. Ing. El Bulletin de la Association des Ingenieurs Elec- triciens Sortis de l'Institut Electrotecnique Montefiore, Liege. Bull. Soc. bilge d' Elec Bulletin de la Société belge d'Electriciens. Col. Guard . Colliery Guardian. D. R. P Deutsches Reich Patent. Dilly. Poly Dingler's Polytechniches Journal. E. & DI. Jour Engineering and Mining Journal. E. T. Zeit Electrotechnische Zeitschrift. Eclair. Elec. L'Eclairage Electrique. 1;1. Anzeig Elektrotechnischer Anzeiger

Sep 1, 1910

By T. Egleston

The importance of condensing the gases which escape from furnaces so as to save both the fine particles of ore carried off mechanically and those which are volatilized, has for a long time occupied the serious attention of metallurgists in all parts of the world. It was my good fortune during the last summer to visit the lead and silver works at Ems, near Coblentz on the Rhine, and through the politeness of Mr. Freudenberg, general director of the works, to study in detail their methods of condensation, and to receive from him the important results which have been obtained through a series of experiments lasting over a number of years. I have thought, that these results would be of great interest to the members of the Institute and to other metallurgists in the United States, and I have, therefore, with the assistance of Mr. Freudenberg, prepared a careful, detailed description of the construction of the flues, as well as an account of the various experiments which have been made with them, and the conclusions arrived at as the result of these experiments. It may be said, in general, that the reason why so little attention has been paid in the metallurgical works of the United States to the collection of flue-dust, is that we are not generally aware of the large amount of material carried off by the gases. This is owing partly to the fact that little or no attention is paid to the subject, and also to the fact that the assays, which are almost invariably made in the dry way, show a result so much below the real contents

Jan 1, 1883

New Jersey Zinc Co. - The Plants Canon City Palmerton Depue

Jan 12, 1953

By H. H. Rachford

Numerical solutions of immiscible flow problems in which dispersive effects of capillarity are dominated by convection require excessively fine grid spacing with attendant high computing costs. The use of coarser spacing reduces cost but often produces oscillation or undue dispersion associated with displacement fronts, A numerical formulation is proposed here which should be applicable to two-dimensional flow problems. it is in part analogous to an approach previously tested for miscible systems. The convective transport is approximated using a change of variables to yield a coordinate system moving approximately with the local characteristic velocity. The capillarity-induced dispersive terms in the differential system describing the process are approximated with respect to a fixed coordinate system by the usual implicit formulation. One-dimensional tests of the procedure yielded results in which the saturation profiles tended smoothly to the zero-capillary pressure solution as the ratio of viscous to capillary forces was successively increased in a sequence of calculations. This contrasted favorably with solutions by other numerical procedures which would require attendant grid refinements to approach the zero capillary pressure results. INTRODUCTION Numerical solution of displacement problems has until recently relied on applying methods developed primarily for transient heat-flow problems. Such problems are classified as parabolic in type, and where the heat transport is purely by diffusion their solutions are characterized by a high degree of smoothness. It is not surprising, therefore, that for approximating these solutions available finite difference methods are quite adequate. In flow problems the transport is partly by diffusion, partly by convection or flow. Although the problem remains of parabolic type because the dispersive effects of capillary forces or diffusion play some role in every displacement, at high flow rates the problem is dominated by convection, and solutions tend toward those of equations of the hyperbolic type. Solutions of hyperbolic problems are characterized by the translation of fronts, or discontinuities, that may progressively increase in sharpness. Numerical methods for treating parabolic problems become less and less satisfactory as displacement rates increase and the role of dispersion due to concentration or capillary pressure gradients becomes small relative to transport due to flow. In computation the difficulty manifests itself as an error associated with the grid size chosen. 1-6 In summary, if the heat-flow type approximations are to include the terms arising due to convection, one of several choices may be made: (1) an upstream (to the direction of flow) approximation for the convection terms may be used; (2) a centered-in-distance (CID) approximation may be used; or (3) a recently developed approximation based on the theory of oscillation matrices may be chosen.6 The last appears to have significant promise for one-dimensional flow problems; its extendibility to two or three dimensions is an open question. In either of the first two approaches, a suitably small ratio of v&/D must be maintained, where v is the velocity, & is the grid spacing and D the effective dispersivity in the direction of flow. In the first choice, the approximation of the convective part is only first-order correct and errors introduced appear as a numerically induced dispersivity of magnitude proportional to v?x. In the CID choice, the approximation can be second-order correct, but the difference formulation fails to satisfy the maximum principle unless a condition on v?x/D is met. Practically, this means that for high flow rates oscillatory solutions may result in the neighborhood of a front unless exceedingly small grid intervals are taken. While the procedure proposed by Stone and Brian4 permits a less severe limitation to be placed on this ratio, ultimately the flow rates increase relative to the dispersivity the oscillation obtains. Further, extensions of their approach to higher dimensional systems may be attended by considerable

Jan 1, 1967

By R. H. Brown, F. Keller

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By F. Keller, R. H. Brown

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

R. W. Guard (General Electric Co., Schenectady)— The method of fractional replication discussed by the author has proven very valuable to us in applied research connected with alloy and process development where many of the same experimental difficulties exist. Several of our experiences may be of assistance to those who want to apply the method in these fields. Contrary to the author's observation that interactions are rarely significant, we have found in a number of cases that first order interactions exist which are significant and metallurgically important. Because of this difference there are two further precautions which should be taken in order to minimize the difficulties from this point. First, in evaluating the importance of

Jan 1, 1957

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968

By Kurt Stock

The war caused a demand for enormous quantities of high-grade zinc, which were not available and could not be produced from pure ores in sufficient amounts and in the time required. Redistillation of virgin spelter on a large scale was practiced to supply this demand; this paper gives a full description of the process used by the Oklahoma smelters of the Bartlesville Zinc Co. As the redistillation of zinc has become of historical interest only, having been superseded by the electrolytic process, it was deemed advisable to give expression to this phase of the metallurgy of zinc that, in the past, had never gone beyond laboratory experimentation. THE grades of spelter demanded by the consuming industries were not definitely established until the American Society for Testing Materials undertook to fix specifications, based on the varying percentages of the common impurities (lead, iron, and cadmium) as follows: TOTAL, NOT LEAD, IRON, CADMIUM, OVER. PER PER CENT. PER CENT. PER CENT. CENT. A. High grade 0.07 0.03 0.05 0.10 B. Intermediate 0.20 0.03 0.50 0.50 C. Brass special 0.75 0.04 0.75 1.20 D. Prime western 1.50 0.08 The question which grade was the best for certain purposes and why was left unanswered. The conservatism of the zinc-smelting industry and the unwillingness of the spelter-consuming industries to engage in research work prevented the full benefits being obtained that such standardization promised. The custom smelters, producing spelter in pigs or plates, found it impossible to adhere closely to the established limits on account of the variety of ores treated; and the smelters with long-established and known brands, or those manufacturing their metal into marketable products, like sheet zinc, did not have to abide by the newly established grades based on chemical percentages.

Jan 7, 1924

By George D. Graffin.

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 A.D. graphite crucibles were being made in the Haffnerzell district of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still used for the mineral are "Plumbago," meaning leadlike, and "Black Lead." The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it "graphite" from the Greek word "graphein," meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Ceylon (now Sri Lanka) graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite. Physical Properties and Classification Graphite is found in laminated, flaky aggregates disseminated in schistose rocks. It also occurs in veins and exhibits a foliated or fibrous structure. Graphite is a black lustrous mineral that crystallizes in the hexagonal system, with rhombohedral symmetry. The crystals have tabular form and are six-sided; the faces are commonly striated. The flakes have perfect basal cleavage and are opaque. When well crystallized, the flakes have a black metallic luster while the amorphous material is black and earthy, with a microcrystalline compactness. The flakes feel greasy. Graphite is an excellent conductor of heat and electricity. It melts at approximately 3550°C at a triple point under 1250 psi. It sublimes between 3300-3500°C at 14.7 psi. At 3726°C a second triple point occurs at approximately 100,000 atmospheres. Thermal oxidation in the presence of oxygen begins at 300°C and the rate increases with temperature. The three forms of carbon (charcoal, graphite, and diamond) are distinguished by chemical and physical tests. The specific gravity of charcoal is 1.3 to 1.9, of graphite 2.266 g/ cm3 (crystal density), and of diamond 3.5. Graphite has a hardness of 1 to 2 (Mohs' scale). Natural graphite can be divided into three classes: disseminated flake, crystalline vein (fibrous or columnar), and amorphous. Flake graphite is a lamellar form found in metamorphic rocks, such as marble, gneiss, and schist. Each flake is separate, having crystallized as such in the rock. Crystalline vein graphite is found in the form of well defined veins or as pocket accumulations along the intrusive contacts of pegmatites with limestones. The graphite of such deposits is of two types, foliated and columnar. The important Sri Lanka (Ceylon) deposits are vein type. Amorphous graphite is commonly found as minute microcrystalline particles more or less uniformly distributed in feebly metamorphic rocks, such as slates and shales, or in beds consisting practically entirely of graphite. The latter usually are metamorphosed coal seams and carry as much as 80-85% graphitic carbon, while the former, being altered carbonaceous sediments, commonly range from 25 to 60%

Jan 1, 1983

By A. Brown

RAPIDLY rising world demand for mineral pro- ducts has accelerated depletion of the more readily accessible ores, particularly those of premium grade. Operations must proceed at a faster rate to deeper horizons, where there are problems of ground control that restrict economic recovery of the mineral and introduce new hazards to mine personnel. For some of the new Canadian mining fields severe problems of ground stress are still in the future, but much of Canada's mineral output comes from well established mines that have reached considerable depths. It must also be anticipated that the depletion of premium grade ores will eventually necessitate mining low grade material at competitive cost, and unsolved problems of ground control can materially increase costs. Studies of ground stress phenomena in underground workings are therefore considered a present-day necessity, especially since these investigations must be a long-term effort owing to the highly complex nature of the problem and the difficulty of making full-scale observations.

Jan 8, 1958

By Gordon MacVean

THE adoption of rock dusting, as a safety measure, has made notable progress in the West Virginia coal mines since May, 1925. At that time there were but two mines in the State that were thoroughly rock dusted, mines No. 2 and No. 12 of the Boone County Coal Corp., at Sharpless. Since then it is probable that 75 per cent of the coal operators in the State have given consideration at one time or another to rock dusting. This growth of interest followed the meetings of the various mining institutes all over the country, during the summer of 1925, at which papers were presented, drawing the attention of the coal mining operators to the merits of this safety measure. Yet outside of the experience with rock dusting at the Old Ben Coal Corp., of Southern Illinois, and the Carbon Fuel Co., of Rains, Utah, there had been no actual occurrence in the coal mines of the United States, which could be taken as positive evidence of the efficacy of rock dusting in the prevention of the propagation of coal dust explosions. The U. S. Bureau of Mines, however, had run innumerable tests under conditions which closely approximated actual coal mining conditions and had clearly shown that rock dusting was effective.

Jan 1, 1926

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc has been used as an instrument for comparison of the absorption and sectioning techniques as a means of studying diffusion. Single crystal as well as poly-crystal samples were used asanda the temperature range of diffusion extended from 200° to 415°C. For temperatures above 200°C, the data indicate that the results obtained from the absorption technique agree with those obtained from the sectioning technique. The effect on the values of the diffusion coefficient of electroplating vs evaporation as a means of applying the tracer was investigated and no significant difference observed. It was found that an excess or deficiency of tracer did not materially affect the results obtained from the sectioning technique, but invariably caused errors with the absorption technique. NEARLY all self-diffusion experiments and many alloy diffusion experiments have employed radioisotopes as the instrument for following the diffusion. Of the various techniques in which radioisotopes are applicable, the two most widely used are the sectioning and absorption techniques. In the former, the diffusion coefficient is obtained from a curve of log concentration vs the square of the mean penetration depth. In the latter, the diffusion coefficient is calculated from a knowledge of the decrease in activity at the surface after diffusion. In spite of the importance of knowing the reliability of the diffusion data and the widespread use of these two techniques, they had not been directly compared experimentally on the same samples. Thus, such a comparison was worthwhile. The specific system chosen for this comparison was the self-diffusion of zinc, since the metal was readily obtainable in high purity, single crystals were easily grown, and the anisotropic features of the diffusion added an additional factor of interest to the comparison. Self-diffusion in both single and polycrystals was investigated, since the possibility existed that grain boundaries and grain boundary diffusion might produce different effects for the different techniques. Also, the effects of electroplating vs evaporation as a means of applying the radioactive tracer, and the effects of applying an excess or deficiency of tracer material were studied. The general experimental procedures and the mathematical analyses of both techniques have been described previously in some detail, and only those points essential to an understanding of the present work will be discussed here. The mathematical analysis of the sectioning data requires only a knowledge of the solution of Fick's equation. where C,, is the initial concentration, C is the concentration at depth x, D is the diffusion coefficient, and p is the absorption coefficient of the solvent metal for the radiation from the solute. Having obtained F from the experiment, the value of z can be read from a plot of F vs In z, and D can then be calculated if is known. The necessity of knowing the absorption coefficient causes most of the criticism of the absorption technique. It is very difficult to measure accurately under the conditions existing in the diffusion experiment, but it is absolutely necessary, as will be indicated briefly later. Portions of this problem have been discussed in detail elsewhere." The difficulties involved in the measurement of the absorption coefficient arise from three principle factors: the physical characteristics of the absorber, the geometry, and complex radiation spectra. The first two are heavily dependent upon the third. If

Jan 1, 1957

By G. R. Love, M. L. Picklesirner

THE use of color adds a new beauty, power, and versatility to metallography. This has been amply demonstrated in a number of public exhibits and on the walls of corporate, government, and university metallographic laboratories around the world. Indeed, in a number of cases, the color not only is of esthetic value but is scientifically essential to the competent examination of particular samples and systems. Optical strain analysis,' determination of true grain size in U-A1 alloys: phase identification in Nb-base alloys,3 analysis of transformation rates in heat-treated Nb-Zr alloys,4 measurement of solidification segregation in cast Nb-Zr alloys,' study of the intermediate phases in Nb/Sn diffusion couples,6 investigation of the oxidation kinetics at various surface orientations in single crystals,7'8 and a number of other research efforts9'10 would have been vastly more difficult without the extra clarity and distinction introduced by color—either the colors resulting from particular polarized light techniques or the interference colors obtained by oxidation. It is unfortunate that the beauty of colored micro-structures cannot be shared more widely, but the economics of publishing a technical magazine apparently prohibits color plates except under extraordinary circumstances. It is doubly unfortunate that no convenient, general method exists for communicating the information available in colored microstructures to the scientific community. True, in some instances the color changes observed are dramatic enough that direct black and white photography is adequate. In photoelastic stress analysis, several orders of interference fringes may be produced and it is frequently desirable to suppress the color effects (use monochromatic light) to simplify interpretation. On the other hand, relatively minute color variations may be readily detectable by eye, be of considerable assistance in interpreting a structure, and yet be enormously difficult to reduce to an unambiguous black and white print. In order to illustrate a possible compromise or solution to the above problems, we wish to show three black and white photographs of the same region of an Nb/Sn diffusion couple whose interpretation depends heavily upon use of color techniques. These micro-structures were obtained from a section through a rod consisting of commercial-purity niobium tubing filled with 99.995 pct Sn (melt-filled in 10"6 Torr vacuum). The composite rod, measuring 500 mm long, was bent into a hairpin shape and inserted into water-cooled copper grips in a vacuum high-temperature furnace. The rod was outgassed for 2 hr at a furnace temperature of 800°C and was further heated by self-resistance using a 2.2-kva ac power supply. The rod was raised to 1910°C over a 4+-hr period, held for 15 min, slow-cooled to 1500°C over a -hr period, and free-cooled to room temperature (all temperatures were measured with W5Re/W26Re thermocouple). Throughout the heat treatment the ambient pressure was kept below 8 x lo-' Torr. Metallographic preparation of the sample was completely conventional except that it was necessary to extend the grinding steps to remove damage in the brittle NbsSn phase introduced by sectioning. No satisfactory chemical or electrochemical etch has been found for these diffusion couples; of those which have been tried, any that attack the niobium-rich phases at all attack the tin-rich phases disastrously. However, the final polishing steps did produce a slight relief effect and this, coupled with anodizing, yielded excellent clarity in the microstructures for direct observation. The anodizing voltage was chosen to give maximum change in color per unit change in composition. In this case, indeed normally, this maximum sensitivity occurred in the blue-to-red color range. The pure niobium tube wall anodized to a relatively bright blue

Jan 1, 1967

By ERIIL SCHROEDTER

THE death, on May 6, 1908, of Dr. Hermann Wedding, Privy Mining Councilor of the Kingdom of Prussia, and Professor of the Metallurgy of Iron and Steel at the Royal Mining Academy of Berlin, was a loss keenly felt by the whole metallurgical world. Not alone in his native land, but also in foreign countries did he enjoy an esteem of which the title of honorary membership in the American Institute of Mining Engineers, the United States Association of Charcoal Iron-Workers, and the (British) Iron and Steel Institute bears eloquent testimony. Hermann Wedding was born March 9, 1834, in Berlin. At the suggestion of Dr. C. J. B. Karsten, the veteran father of Prussian metallurgy and author of the first German text-book of the metallurgy of iron, lie turned his attention, after gradu¬ating from the gymnasium, to mining and metallurgy. In 1853, he began a practical course at the Malapane iron-works, in Upper Silesia. Subsequently, he studied at the Berlin Mining Academy, and received from the University in 1859 the degree of Doctor of Philosophy. A journey which be made to England, somewhat later, led to his undertaking a German translation, with revision and additions, of John Percy's classic treatise on the metallurgy of iron and steel, the publication of which, in successive installments, stretched through many years. In 1863, lie published, as a thesis in connection with his "Assessor's examination," an essay, entitled The Results of the Bessemer Process for the Production of Steel, and Its Prospects for the Rhenish and Westphalian Iron and Steel Industry, which revealed such ability and knowledge as to secure for him a call to the chair of metallurgy in the Berlin Mining Academy.

Jun 1, 1909