Search Documents

By Jorge Castillo

This paper presents a dynamic analyses of heap leach pad stability under high phreatic levels and various levels of seismic loading. The dynamic analysis were conducted as fully non-linear two dimensional analyses with fully coupled liquefaction triggering using the Fast Lagrangian Analysis of Continua (FLAC) computer code. Also, the geotechnical parameters, appropriate earthquake record selection and modification, model calibration, numerical analyses and results are discussed.

Sep 12, 2005

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004

By C. B. Manula

Simulation continues to hold the spotlight among the Operations Research applications in the operational side of mining. One reason for this is the need to solve the many waiting line and storage problems common to the industry. A second reason for using simulation is the central requirement of retrospect testing. Acceptance of a model by management is more likely to depend on its tested performance rather than on the underlying validity aspects of the model itself. Mathematics have not been and may not be developed that will allow all desired system elements to be considered simultaneously. It is in this realm that simulation bridges the gap between theory and useful design procedures. One of the earliest published accounts of simulation at work in the coal industry is demonstrated by the application cf Monte Carlo methods to explore changes in future operating policies for an existing track system (Manula, 1963). By modifying certain control parameters, revision in design changes were evaluated in the computer rather than in the actual production section. A second application which has found wide use in practice is the VFI-OCR Face Simulator (Prelaz et al., 1968). The model developed here has the purpose of allowing the comparison of methods for room-and-pillar face operations end observing their effect on mining prior to actual installation. Proposed changes are tried in the model and the best of these are selected as a guide for better mire management: IBM's own simulation package, the System 360 General Purpose Simulator, has experienced heavy use in solving similar problems and other steady-state situations.

Jan 1, 1974

By H. Askari-Nasab, S. Upadhyay, A. Moradi-Afrapoli

Material handling in surface mines accounts for around 50% of the operational cost. Optimum truck dispatching plays a critical role in the reduction of this operational cost in truck and shovel surface mines. Researchers in this field have presented several mathematical models to solve the truck dispatching problem optimally. However, a critical survey of the literature has shown that three significant drawbacks exist in the available truck dispatching models. The published models underestimate the importance of the interaction between truck fleet, shovel fleet, and the processing plants. They also disregard goals set by strategic-level plans. Moreover, none of the available models account for the uncertainty associated with the input parameters. In this paper we present a new truck dispatching model that covers all of these drawbacks, using a fuzzy linear programming method. The performance of the developed model was evaluated through implementatin in an active surface mining operation. The results show a significant improvement in production and fleet utilization.

Sep 1, 2021

By H. H. Stoek

MINE models have three distinct uses: 1. As exhibits in expositions and museums. 2. As exhibits in law suits. 3. As illustrations in teaching mining engineering. All three uses are in a sense educational. The third, or distinctively teaching function, has not been extensively developed in America as it has been abroad, chiefly because of the cost of the models and the scarcity of model makers. In connection with expositions, such as the Columbian, the Louisiana Purchase, and the Panama-Pacific, a number of very good mine and metallurgical models were prepared with funds furnished by State commissions, by mining organizations or mining companies. At the close of these, expositions, some of these models have been deposited in National or State museums or in educational institutions, but too many of them have been lost, or have been stored, away in some mining company's office or in the basement of some State building, where they have been lost sight of and have gradually fallen to pieces. A visitor to a German mining school is impressed by two facts: 1. The mining laboratories are in general inferior to those in America. 2. The mining museums are infinitely superior -to ours, particularly in models exhibited. One may reply to this comparison by saying that a museum is necessarily a work of time. From the historical standpoint this is, of course, true, but it is not necessarily true in connection with a working museum intended to illustrate current practice. For instance, the oldest mining school in Germany, that at Freiberg, has much excellent historical material, but very little on modern practice, while Berlin, one of the youngest German mining schools, has a most extensive and valuable collection of modern appliances and models. This is true in spite of the fact that one of the best-known model shops is at Freiberg, from which many of, the models to be seen in America have come. Because many of the models in American mining schools have come from

Jan 4, 1917

By N. Demirel, O. Gölbasi

Draglines are massive machines extensively utilized in opencast mines for overburden stripping. The demanding working environment induces fractures, wear and tear, and fatigue failures in dragline components and eventuates in extended maintenance, lengthy downtimes, and loss of production. The bucket is the main source of external loads on the machinery, since interactions with ground materials take place in this region. This study aims to develop a generic finite element model of the stress on an operating bucket. This entails (i) three-dimensional modelling of a dragline bucket, (ii) analytical estimation of resistive forces in the bucket movement, (iii) three-dimensional simulation of the moving bucket using finite element analysis (FEA), and (iv) sensitivity analysis to examine the effect of formation characteristics on stress variation. Simulation results imply that the drag hitch and digging teeth are the elements of the bucket that are most prone to failure. In addition, sensitivity analysis indicates that internal friction angle of the formation is the dominant parameter leading fluctuations in stress values. Changes in stress level are least influenced by formation density.

Jan 1, 2015

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals in the hope of understanding the reasons for poor performance when it occurs, and developing mitigating strategies.This testwork along with a review of the relevant literature has demonstrated that the amount of sulphide added to the primary reactor, relative to the copper concentration, is the most critical parameter dictating plant performance, with pH and residence time important secondary factors. The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. Testwork shows that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. The theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are likely to experience growth in crystal particle size through aggregation rather than heterogeneous nucleation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process.There is evidence to suggest that operating the copper sulphide thickener in the SART Process without flocculants may be beneficial. Thickener underflow densities could improve from the current 10 - 15% range to 40 - 50%. This will not only reduce the flowrate of slurry to the filter, but the filtration properties of the slurry (filtration rate, filter cake moisture content) will also improve. This is one of the most critical engineering and design aspects of the SART Process, and the achievement of high solids density in the thickener underflow will not only improve the health and safety aspects of the operation, but also has the potential to lower capital costs and improve the quality of the final product."

Jan 1, 2016

Particles of a complex nickel sulphide concentrate (containing pyrite, pyrrhotite, pentIandite, and violarite as the major mineralogical constituents) were entrained in a stream of hot gas the temperature of which was varied from 500 to -1000°C. Chemical analysis of the particulates collected from the furnace was used to detect the rapid change in sulphur content which accompanied the ignition temperature jump. X-ray diffraction analysis was used to characterize the oxidized material.These techniques showed that ignition was dependent on the mineralogical composition and occurred over the temperature range 500-900°C. Pyrite ignited first in the range 500-600°C; pyrrhotite was the least reactivemineral and required temperatures in excess of 800°C for ignition. The nickel minerals <pentIandite and violarite decomposed before ignition and ignited at temperatures intermediate to those required for the pyrite and pyrrhotite. The ignition temperature for the pyrite was found to be independent of particle size and concentration of oxygen in the atmosphere.Ignition temperatures determined by the simulated flash smelting method were compared with the results of differential thermal analysis (DTA) measurements performed on the same concentrate. Temperaturesdetermined in the DTA test as corresponding to the start of exothermic activity were shown to be at least 100°C below those determined by the simulation test.

Jan 1, 1978

It is a great honour to be privileged to address The Institute for a second time as President and I appreciate it more than I can say. Eight years ago in Hobart I tried to cover the development of the mineral industry in Tasmania. That was a general subject. Tonight I want to be more specific - I propose to talk to you about rutile.The choice of subject for a Presidential Address is never easy. One is addressing an informed audience and the best one can do is to try to crystallize a particular subject and to present it in a form that willbe of interest to those who listen.I looked carefully at the addresses given by our Presidents over the past seven or eight years. The titles are impressive, the content excellent, and the length, as published, much greater than I had hoped.It is therefore with some trepidation that I have chosen as a subject one only of the three crystal forms of titanium dioxide. This subject is not as limited as may at first appear.There are two aspects with which I can deal - the mineral itself, which has become familiar as the major product of the East Coast beach sand operations, and the lesser-known "synthetic" product, which is the major pigment in almost all the white paints in common use today, and in cosmetics and white-walled tyres and toothpaste, and even the better types of fine papers. The synthetic form of rutile is' the "whitest"of white pigments.

Jan 1, 1966

By Lowell Stroud

This report is the third in a series presenting equilibrium vapor-liquid data for helium-bearing natural gases. The first two reports contained phase data for the gases processed for helium at the Bureau of Mines Amarillo and Exell, Tex., helium plants. The present report offers similar information for a lower-helium-content (0.75 mole-percent) natural gas to be processed in the Department of the Interior's long-range helium-conservation program. A windowed-cell apparatus was used to obtain 218 samples of equilibrium vapor and liquid phases at 73 experimental conditions ranging in temperature from -100° F to -275° F and in pressure from 100 to 500 psi. From the phase data, the condensation characteristics, helium solubility, and equilibrium-vaporization-coefficient data for helium, nitrogen, and methane were evaluated. The effect of using a. preliminary hydrocarbon trap upon the subsequent vapor-liquid compositions is reported. A brief comment regarding the composition effect of passing the gas through a gasoline-removal unit is also included.

Jan 1, 1963

The seams of black coal occurring in Victoria are so disturbed by faulting, wash-outs, thinning, etc., that it is necessary, for the prevention of costly errors in development, that close boring be undertaken so that the correct positions of the shafts, tunnels, main and auxiliary roadways can be set out in order that the area can be economically worked. The State Coal Mine has two boring plants continuously at work, which have given good service for the last twenty-five years.The information supplied herein is merely our experience in boring at the State Coal Mine over an extended period. The type of plant in use is that known as the Victoria Drilling Plant, equipped with an 11 h.p. portable oil engine, using power kerosene as fuel. It was purchased in 1914, complete with mechanism for cable drilling, capable of boring to a depth of 1500 ft. with a guarantee of 1000 ft., with Calyx cutters, boring rods and all necessary equipment for the sum of £1473. The chief mechanical features of the plant are as follows:-The derrick is in the shape of a tripod (see Fig. 1), two of the legs being of steel channel built together to form a frame which, when lowered on to two sets of road wheels, forms a carriage for the transport of a portion of the boring equipment. The third leg is made of oregon in the form of a double bow, with bolts and distance pieces between the wooden sides. The top of this is hinged on to the steel frame, and the bottom is fitted into a cast iron block, having two small wheels to facilitate erection. A rope attached to the cast iron block and to the winch easily...

Jan 1, 1936

By J Seccatore, F Golin, E Munaretti, M Cardu, J C. Koppe, J Bettencourt

Contour blasting is commonly performed by employing linear charges decoupled from the boreholes. This method is common in surface and underground excavations, either for civil or mining purposes. To achieve the best results in terms of rock breakage and respect of the excavation profile, blasting theory suggests that charges should be inserted coaxial to the holes to grant uniform distribution of the explosive energy, therefore obtaining a uniform radius of damage. Nonetheless, due to readiness of operations or lack of availability of specific products on the market, non-coaxial charges are often employed in blasting practice. Non-coaxial charging methods include the employ of high-power detonating cord (40 to 100 g/m), low-power detonating cord connecting small-diameter cartridges (commonly 10 g/m detonating cord priming 1” cartridges) or string loading (a thin layer of bulk emulsion pumped with controlled flow and controlled extraction of the injecting rod). This research focuses on evaluating the effects of the first two charging methods on the quality of final walls in open pit and underground operations. Different drilling geometries and charging configurations were applied to both quarrying and tunnelling blasts. The half-cast factor, the overbreak and the underbreak were evaluated as control indicators. Rock quality designation and rock mass rating were used to classify the rock mass. The research was aimed to push contour blasts to their limits, observing for which geometry and charge configuration the blast lost its design threshold with respect to the final wall for every given rock mass. Results show the operational limits of non-coaxial charges encountered in the rock masses object of this study. In good-quality rock, smooth blasting with decoupled linear charge of 40 g/m can be extended to a spacing S = 22Øf with little or no detectable drawbacks in terms of final wall quality, in contrast with theoretical formulae for the determination of the radius of damage. On the other hand, when the rock is poor, any quality of the final wall is hardly achieved at all, in spite of any care in the details of execution of smooth blasting. It is concluded that any design criterion and theoretical approach modelling the effects of contour blasting cannot ignore the features of the rock mass.CITATION:Seccatore, J, Golin, F, Cardu, M, Munaretti, E, Bettencourt, J and Koppe, J C, 2015. Evaluating the effects of non-coaxial charges for contour blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 267–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Edward L. McHugh, Louis J. Denes, Jami M. Girard

A prototype portable hyperspectral imager that operates in the visible and near-infrared ranges of the electromagnetic spectrum was field tested at an open-pit mine. The tests were sponsored by the Spokane Research Laboratory, National Institute for Occupational Safety and Health, as part of an investigation of remote sensing technologies for use in detecting and monitoring conditions in surface mines that could lead to catastrophic slope failure. The spectro-polarimetric imager, built at the Carnegie Mellon Research Institute, employs an acousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. The spectral range of the instrument is 450 to 1000 nm at 10-nm intervals. High-resolution hyperspectral images of highwalls, outcrops, hand samples, and drill core were collected in the field. Spectra from the images closely matched those of specific minerals present and were used to classify the images. The field tests were designed to examine the feasibility of using spectral imaging to assist in compiling objective geologic maps of mine highwalls and other hazardous slopes. Results illustrate the capability of the method to discriminate materials within the image, validating the concept of simplified spectral imaging. A contributing factor in many slope failures is the presence and distribution of mechanically incompetent, clay-rich altered rock in slope faces. Spectral features of clays and other minerals are more distinctive in the short-wave and mid-infrared part of the spectrum; the capabilities of the instrument need to be extended into this range to apply the AOTF-based technology to common geologic materials. A field-portable hyperspectral imager could find broad application in remotely identifying diverse materials from solids and coatings to gases.

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

By Diego Pinheiro Aun

Neste trabalho, foi investigada a influência da textura de fitas de NiTi superelástico no início do processo de cristalização de um revestimento de TiO2 flexível. Foram utilizadas a calorimetria diferencial, cartografia Raman e difração de raios X para o estudo. Foi mostrado que existe uma influência significativa da textura do substrato no crescimento de grãos de anatase e rutila no filme de TiO2. Amostras com menor rugosidade apresentaram grãos mais desenvolvidos para todas as temperaturas de cristalização. Mostrou-se também que o substrato de NiTi promoveu a formação de TiO2 rutila em temperaturas abaixo daquelas observadas para a cristalização de pós.

Aug 16, 2017