Search Documents

By T. J. Snell

Bolnore Village in Haywards Heath, Sussex, England, is a large development covering 8 to 10 hectares and expected to provide 1500 homes in five phases to assist in the continuing demand for new homes in the London area. Part of the development required housing on a relatively shallow slope found to have deep seated failure planes which are fairly prevalent in this part of Sussex. Locally the slope angle was around 20 degrees but more typically the gradient was 6 to 7 degrees. There were significant concerns about slope stability and bearing capacity due to pre-existing shear surfaces and the complex geotechnical profile. There was some evidence of instability in the form of residual shear surfaces and tension cracks. The development required terracing the site with retaining structures up to 5 meters in height, formation of access roads and foundations of new houses. The developer Crest Nicholson adopted a collaborative approach with consulting engineers Powell Tolner and specialist geotechnical contractor Keller Ground Engineering. The solution consisted of a novel combination of contiguous bored piling, ground anchors, and both block work and timbacrib retaining walls to ensure the geotechnical issues were adequately addressed within the time and cost constraints set by the team. The paper describes the geotechnics of the problem together with the design, practical implementation, and site progress achieved

Jan 1, 2006

By Michael Mann, Kenneth K. Eltschlager

The International Society of Explosives Engineers (ISEE) Standards Committee has recently updated both the Field Practice Guidelines for Blasting Seismographs and the Performance Specifications for Blasting Seismographs. The revisions are the result of public and industry input along with recommendations of the ISEE Blast Vibration and Seismograph Section. The committee is comprised of blasting seismograph manufacturers, users and general interest personnel. On an as needed basis, subject matter experts are enlisted to advise the committee. Three phases of activities are necessary for each revision cycle: request for comment on the existing standard, first draft revision of the standard based on public input, and final draft approval by the ISEE Board of Directors. The ISEE standards revision process will be explained and each standard will be discussed along with the significant revisions from the latest revision cycle.

Jan 1, 2018

By K. Lundholm, A. E. Mäkinen

"Ore grades are declining and getting more complex around the world which not only complicate the ore processing but also produce new type of requirements to manage the produce waste streams. One specifically problematic and increasingly identified element in waste streams produced in mining and metallurgy is arsenic.Arsenic is a compound that has no significant market value, but that needs to be removed from ores, concentrates and other process streams because of environmental or process technical reasons. One example of a removal process is partial roasting of high-As sulfide concentrates, originally developed by Outotec. In this process the arsenic is volatilized in the gas phase and thus separated from the solid material, i.e. the calcine. If the arsenic is recovered by wet methods the process gas is quenched and all arsenic needs to be stabilized in the effluent treatment plant.Outotec has developed ferric arsenate precipitation as a method to produce stabile arsenic residues from wet gas cleaning effluents. Iron based precipitates, when correctly produced, can meet typical landfill criteria measured with different types of leaching methods meant for characterizing the arsenic dissolution behavior from the precipitates.In this paper partial roasting of sulfide concentrates with arsenic volatilization in combination with ferric arsenate precipitation is discussed from the perspective of producing wastes that can meet the stability requirements set by common leaching tests methods, TCLP and CEN. These leaching test methods set the normative landfill requirements for most operations generating arsenic containing wastes. A typical flow sheet of Outotec® Ferric arsenate process is discussed with results showing the importance of correct process control and sequence on producing arsenic containing waste that can meet the landfill disposal requirements."

Jan 1, 2014

By E. S. Yan, R. Graley

"The StackCell was developed to overcome the engineering and design challenges that are commonly associated with existing flotation technology such as pneumatic, self-aspirating cells, mechanical cells, and flotation columns. These challenges include high energy consumption, large floorspace requirements, and size. They are most evident when designing systems to process streams containing a high volumetric flow rate coupled with a significant float yield. Unlike many metalliferous and industrial mineral applications, fine coal flotation circuits are typically characterized by feed streams containing a low solids content (<5%, by weight) where up to 85% of the feed can report to the product launder. With input from major engineering houses and end-users, the Eriez Flotation Division (EFD) developed the StackCell technology with the goal of providing an additional flotation option for end-users. This technology was designed specifically to overcome these challenges by providing an efficient method of separation in terms of metallurgy, but also with respect to equipment size, energy consumption, and installed costs. Besides being placed in tandem with existing cells to provide cost-effective supplemental capacity, this technology can be installed in a stand-alone arrangement as recently demonstrated at Patriot Coal’s Kanawha Eagle preparation plant. This manuscript provides an understanding of the underlying fundamentals of this new technology and presents data from Kanawha Eagle in addition to other industrialscale installations.INTRODUCTIONOver the past decade, column flotation has continued to gain acceptance as an alternative method for recovering fine coal due to superior metallurgical performance as compared to mechanical flotation cells. This point has been proven on numerous occasions by comparison of plant flotation data with the release analysis separation curve (Dell et al., 1972). Data from a release analysis test approximates the ultimate flotation response of a coal sample. In North America, a number of investigations have been published that document bottom-line improvements achieved using column cells (Luttrell et al., 1999; Kohmuench et al., 2004; Baumgarth et al., 2005). According to these reports, the benefits are derived from an overall increase in plant yield that can be achieved due to the improved product grade in the flotation circuit. In particular, the application of wash water to a deep froth utilized in column flotation minimizes the nonselective recovery of high-ash ultrafines that are hydraulically entrained in the froth by conventional flotation machines."

Jan 1, 2013

By Sean Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by using assets more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the ?productivity paradox,? where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the true source of benefits is in how effectively IT is used. Most business sectors have accepted that the reengineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors but unique operational processes. The lessons of changing business practice in more common business processes such as inventory control and customer-supplier relationships can be adequately transposed into a mine. The unique operational processes in mines, in turn require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manger training simulators. This paper reviews the latest IT products and ou lines the processes and kinds of change that will be required in order to benefit from these new investment options.

May 1, 2002

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By A. Tobey Yu, W. Joseph Schlitt, Alfred Weiss, Frederic L. Kadey, Louis Kuchinic

Introduction The February and April 1984 issues of MINING ENGINEERING have already provided introduction to the long-range planning efforts of the Society of Mining Engineers (SME). These efforts are intended to provide the basis for effectively maintaining and improving the Society in the face of the changes that are besetting the mineral industry. This requires that SME recognize what changes are occurring and determine how these will impact the membership. Then a plan must be developed and implemented so that the Society successfully meets the challenges of the next decade. The Board of Directors has charged the Long Range Planning Commission with the responsibility for meeting these goals. This article provides a summary of the work done by the Management and Organization Committee of the Long-Range Planning Commission. This committee&apos;s task was to analyze the Society&apos;s current organizational structure and management process. Then a set of recommended improvements was to be developed. In doing this, the Committee has been careful to operate under that popular axiom, "If it ain&apos;t broke, don&apos;t fix it." Thus, changes were not proposed simply for the sake of change, but only where the present system appeared to be less effective than desired. Bases For Action The Committee began by establishing a set of premises about SME and its membership. These premises provided the bases for subsequent actions and recommendations by the Committee. Highlights from the premises included: • The Society should be run on a business-like basis. However, its "business" is that of a not-for-profit scientific, technical, and educational public institution. SME enables professionals involved in or associated with the mineral industry to serve the public purpose of benefitting mankind. • The Society operates as a national (US) organization with transnational (worldwide) interests. It recognizes its obligation to make its goods and services available to minerals professionals throughout the world. In addition, the Society recognizes its obligation to translate technology for the "lay" public, who then also become users of its goods and services. • The Society&apos;s Board of Directors is the policy-making body of SME and has final approval of all programs. These responsibilities will become greater when the Society becomes a separate corporation. • At present, the Society provides the following goods and services: publications, meetings/programming/short courses, academic education support, information dissemination - internal and external, and individual member services. • Planning is an ongoing process. It is best performed on a decentralized basis. That is, each major service category should have a responsible group authorized to conduct planning for that category, subject to the Society&apos;s master plan and the Board&apos;s approval. • The Society is privileged to have highly qualified and motivated members who volunteer their time and efforts on behalf of the Society. The best of these volunteers should rise to the highest positions of leadership - the Presidency of the Society and Institute (AIME). • The Sooiety is strongly committed to the protection and promotion of the history, traditions, and identity of AIME and the use of AIME as the unifying forum for the Constituent Societies. Identification of Potential Problems Once the premises about the Society and its membership were well in hand, the committee began examining the many facets of SME&apos;s organizational structure and management process. This was done in order to identify problems or potential problems in these areas. After considerable review and discussion, 10 areas of potential concern were called out for more detailed study and possible recommendations for improvement. These 10 areas include: • A lack of continuity at the Board level and among officers due to the established turnover policy. • A series of subboards that serve, by practice, to diffuse management authority and accountability, rather than enhance it. • A question as to whether the dissemination of information has been adequately planned, organized, and staffed. • An apparent illogical divisional organization. Two divisions are discipline oriented and two are commodity oriented. • A regional organization that does not adequately fulfill its purposes. • Uncertainties about the per-

Jan 6, 1984

By J M. F Clout

In the iron ore industry significant emphasis is placed throughout the mining process on meeting chemical composition specifications for the export of fine ores, however, little has been published on the implications of ore chemical composition for iron ore sinter and pellet product quality. The ore bulk composition, together with the nature of the minerals in the fine ore both play a critical role in determining the type of high temperature bonding phases that form during sintering and pelletising. This paper uses the experimental determination of phase relations in model sinter and pellet systems such as Fe2O3-CaO-SiO2 (FCS) and Fe2O3-Al2O3-CaO-SiO2 (FACS) to examine the links between iron ore chemical composition and the temperatures used during sintering and pellet firing. The phase relations help to establish the critical thermal and compositional parameters that control the bonding phase chemistry which in turn influences the physical characteristics of the sinter or pellet matrix. Results show that lower Fe-grade (

Jan 1, 2002

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. Basis of operation of the PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, online technologies through review of published information available for on-conveyor minerals applications. Case studies demonstrate benefits provided by this technology in two operating mines. An iron ore company had prior experience with the PGNAA analyser technology, implementing an early model in a minerals application in 2003 to develop confidence in its measurement performance and usefulness of the data. A number of analysers were subsequently included throughout the new plant design for extensive measurement and control of conveyed bulk flows, from conveying after mining through to rail load-out. A copper-gold company installed an analyser to address copper ore blending issues where an on-belt system was the only viable option for the degree of control required. Analyser suitability was evaluated through test work on site samples to determine customised multi-element precision guarantees for each application. Analyser results from normal operation are compared against laboratory analyses of multiple cross stream samples collected from conveyed flows to assess performance. Both projects discussed were able to realise benefits previously unattainable for plant quality control, surpassing capabilities of traditional technologies which were either unsuitable for measuring conveyed flows with adequate accuracy or in real time. Equipment payback within a few months was achieved for both sites. Through proven performance in these applications, the companies consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.

Jan 1, 2014

By J. Baird

The Sappington Bridge, a steel arch span bridge constructed in 1904 over the Meramec River, was demolished due to its advanced state of deterioration. The demolition was a project to benefit Crawford County, Missouri, the U.S. Army, the Missouri Department of Transportation, and the University of Missouri – Rolla (UMR) was conducted jointly by the UMR Rock Mechanics and Explosives Research Center (RMERC) and the UMR Center for Infrastructure Engineering Studies (CIES). By arrangement with Crawford County, a 55-foot span of the old bridge was brought to the University Structures Laboratory in Rolla, while the longer, 200-foot span of the bridge was demolished using preburning and explosives. Originally, the longer span was to be blown up by C Company of the 5th Engineer Battalion (from Ft. Leonard Wood, Missouri) under the supervision of personnel from UMR. Unfortunately, permission for the operation from the Department of the Army could not be obtained in time to meet permitting requirements for the demolition. Therefore, a commercial demolition contractor was employed to perform the demolition, and to remove the scrap.

Jan 1, 2003

This paper has peen translated from the Russian by the United States Bureau of Mines and is issued as one of a series of circulars dealing with mining methods and costs in connection with a general study of this subject sponsored by the bureau. The paper presents some interesting features in connection with the methods employed in Russia and describes certain variations in standard methods which might conceivably be applied to a limited extent in this country.

Jan 1, 1930

By Jay A. Carpenter

THIS preliminary report from the Committee to Study Relations Between Students and the Institute is submitted to our member- ship for consideration and discussion before the general subject comes up for action at the Annual Meeting in February. At present, the A. I. M. E. has a dual relationship with mining students, each relationship in no may connected with the other. To the individual student the Institute offers for $2 a year a Student Associateship in the Institute which carries with it a subscription to MINING AND METAL- &apos;LURGY, a watch fob, and the privilege of becoming a Junior Member after graduation without payment of the -first year&apos;s dues, if one&apos;s application is accepted. To the student&apos;s college society it offers the privilege, upon application, of becoming &apos;an Affiliated &apos;Society, which brings with it no specific supervision or aid, and in turn requires no specific conditions as to membership, fees, or rules. This Affiliated Society is distinctly a school organization which Student Associateship in the Institute can he given special status or ignored, is the local .society sees fit.

Jan 1, 1934

By Albert J. Phillips

FOR the most part, recent changes in nonferrous physical metallurgy have been gradual and of a transition nature rather than abrupt modifications of existing methods. Development of new alloys containing vital constituents in what formerly would have been considered minute amounts has necessitated more precise control of metallurgical procedure than ever before. Realization of the remarkable effects of minute amounts of specific foreign elements in many alloys has brought about a revolutionary control in the selection of even the most commonplace raw materials. In addition, recognition of the widespread occurrence of precipitation hardness in metal systems, and the utilization of many of these, has emphasized not only the need for precise temperature control but also the necessity for considering the time factor in its effect upon properties in the treatment of most metals. These needs have caused the development and widespread installation of equipment that permits precision of control undreamed of a generation ago.

Jan 1, 1935

By R. W. Bartlett

DISILICIDE coatings, MeSi2, on refractory metals are usually grown by a solid-state diffusion reaction similar to the parabolic oxidation of metals. Two or more silicide compounds occur in each of the binary silicon-refractory metal systems. When an adequate source of silicon is available during the coating process, the lower silicide compounds are usually not formed.1 However, during service application of the coated refractory metal, continued heating causes further diffusion and growth of the lower silicides. A study of the growth kinetics of the lower silicides in the molybdenum and tungsten binary systems with silicon was previously reported.2 The present study is concerned with the growth kinetics of Ta5Si3 and Cb5Si3, formed as conjugate layers between TaSi2/Ta and CbSi2/Cb diffusion couples, respectively. Diffusion couples consisting of disilicide-coated tantalum and columbium sheet coupons were subjected to diffusion heat treatments, cross-sectioned, and scanned by an electron-microprobe analyzer to determine the relative X-ray intensity profiles. These profiles correspond closely to concentration profiles for the constituents, and were used to identify phases and locate phase boundaries. The analysis of a single specimen after a diffusion-anneal provides only one value for the Me5Si3 phase thickness, corresponding to the time and temperature of the diffusion treatment. Consequently, each isothermal curve showing the rate of accumulation or depletion of silicide phases required several samples with identical diffusion temperatures but different diffusion times. The disilicide coatings were prepared by pyrolizing commercially pure silane in a hydrogen carrier gas. The hydrogen was purified by passage through a palladium membrane. Commercially pure tantalum and columbium sheet metal coupons, 0.005 by $ by 2 in., were used. All of the coated specimens for each system were prepared together in a single group in order to minimize coating variations among individual specimens. During pyrolysis, the brightness temperature was maintained at 1200°C. With suitable flow rates at this temperature, only the disilicides of tantalum and columbium were formed in detectable amounts. Coated specimens were subjected to diffusion an-neals in a tube furnace with automatic proportional control within ±10°C. A H2-Ar mixture, deoxidized and dried over anhydrous magnesium perchlorate, was used to prevent oxidation during the diffusion anneal. Diffusion couples were cross-sectioned, polished and examined with an A.R.L. electron-microprobe X-ray analyzer. Both metal constituents in each specimen were simultaneously scanned using a 1-p beam spot size and either 1- or 2-µ steps. Analyses were performed using the Ka radiation of columbium and silicon, and the La, radiation of tantalum. For all specimens, an acceleration voltage of 30 kv was used, and integration was made against the specimen current. LiF and A DP monochrometers were used to isolate characteristic radiations. Three or more traverses were made on each specimen. The intensity scales were adjusted using the constituent metals and standard samples of the silicide compounds which had been verified by X-ray diffraction. The relative intensity profiles were used directly, in conjunction with the standard samples, to identify compounds and phase boundaries. The stoichiometries differ considerably between the silicide compounds in both systems, and the homogeneity range for these silicide compounds is narrow. These characteristics result in marked differences in relative intensities of the fluorescing elements—differences which permit ready identification of phases and phase boundaries. Projections of both electron back-scattered images and characteristic

Jan 1, 1967

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests.

Jan 1, 1934

By R. F. Droullard

The Bureau of Mines has used gross alpha and gross beta detectors to continuously measure radiation working levels for a number of years. During this time, improvements have been made in the design and performance of continuous working-level (CWL) detectors. This report discusses the improved designs and some of the operating principles and applications of CWL detectors in the measurement of radon daughter products in mines and dwellings.

Jan 1, 1985

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009