Search Documents

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using an untreated rock dust and a rock dust treated with an anti-caking additive. Using PDM 3600s and 3700s, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine (BEM) using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device. INTRODUCTION Two factors have combined to renew concern regarding respirable dust measurements and compliance. This renewed recognition is due to two regulations that have modified operators’ rock dust schedules. First, the 80% incombustible requirement in intake entries has increased both on-section and outby-the-section rock dusting. Secondly, the recent respirable dust regulation change that has increased the number of respirable dust samples taken per sampling cycle. Previously, when only 5 samples were needed bi-monthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule. The significant number of samples now required under new regulations combined with the need to maintain 80% total incombustible content in active mining areas require the schedules for respirable dust sampling and rock dusting to intermix. This raises concerns about the amount of rock dust that potentially is included in the sampler weight gain. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 (effective August 1, 2016) increasing concern that rock dust contamination may be an issue. Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application or to schedule rock dusting during a maintenance shift when the number of miners present is lower. NIOSH’s research examining the quality of rock dust has led to the development of hydrophobic rock dusts."

Jan 1, 2017

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By Arno C. Fieldner, Howard I. Smith, J. W. Paul, SAMUEL SANFORD.

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the character and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition, and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1,1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines, July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.a Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.b The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1913 to 1916. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22 and 85, the same plan of geographical classification has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1918

By J. Tuzo Wilson

Abstract A division of part of the Canadian Shield into provinces believed to represent former mountain belts is attempted, special emphasis- being laid upon radioactive age determinations, the relation of Archaean to Proterozoic rocks, and the structure of the Grenville province. Original data on the distribution of radioactivity within several batholiths and their connection with ore deposits are' presented. The possible growth of continents and a theory which explains the shape and distribution of the world's younger mountain and island areas are discussed and applied to the Canadian Shield in an attempt to explain how the growth and present structure came about. The relation of the major mining camps of northeastern Ontario to fault zones is discussed in the light of this theory. Introduction The valuable symposium issued by this Institute to celebrate its jubilees emphasizes the important role of major faults in determining the location of many ore deposits in the Canadian Shield. Many of these faults are known to extend for long distances. It is therefore widely appreciated that it would be of great value if the pattern, ages, and causes of these faults were better understood. This would be particularly useful if the relations of the major fault systems to petrological and metallogenic provinces and to former mountain belts could be established. Each year the volume of available data, and hence the chance of reaching a fuller solution of this problem, increases. This article is a review of the present situation. It is accordingly based almost wholly upon the work and ideas of others, which are gratefully acknowledged. Naturally, responsibility for the selection and marshalling of the data is the writer's.

Jan 1, 1949

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION TO OCTOBER, 1904 Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 28 Montreal, Canada Sept, ?79 8

Jan 1, 1923

By H. M. Smith

MORE than a year before the United States entered World War II, the requirements of the National Defense Program indicated the need for additional sources of aviation gasoline. On September 10, 1940, Dr. R. E. Wilson, Group Executive, Advisory Commission of the Council for National Defense, requested the Bureau of Mines to undertake a survey of crude oils of the United States to designate those suitable for the production of 91-octane aviation gasoline. As quickly as a program could be defined, agreed upon, and funds provided to conduct the work, the Bureau began the project. Over a period of many years the Bureau had collected samples and made analyses of thousands of crude oils produced in the United States. Although these analyses did not include octane numbers of the gasoline fraction, they provided data necessary for calculating the correlation index. This index, developed within the Bureau, is a measure of the types of hydrocarbons present in gasoline and therefore is roughly indicative of the octane value. This fund of information from Bureau of Mines Hempel analyses, supplemented by information obtained from oil companies, reduced considerably the necessary laboratory work by providing data that permitted a large number of crude oils to be eliminated from consideration. However, in the survey carried out during the last part of 1940 and the first half of 1941, 225 samples of crude oil were collected and distilled. Octane values of the distillates were determined by the Army AFD-1C method. (See page 57.) A report containing these results, together with the calculated amounts of 91-octane aviation gasoline available from these sources, was prepared and distributed to the several offices of the Office of the Petroleum Coordinator for National Defense in August 1941. In December 1942 the Office of the Petroleum Coordinator for National Defense became the Petroleum Administration for War (P. A. W.).

Jan 1, 1951

By S. J. Rodgers

MSA Research Corporation, Division of Mine Safety Appliances Company, was awarded a contract to conduct a survey of past and present methods used to control respirable dust in noncoal mines and ore processing mills. The survey covered information reported in mining journals, and U.S. Bureau of Mines Circulars, dust inspection reports, on-site evaluation of dust control methods and systems, and contact with manufacturers of dust control equipment. Both surface and underground mining operations were visited. Fifty mines and 51 processing plants were included in the survey. Dust control methods for the following types of ores or mines were studied: [ ]

Jan 1, 1974

By Thomas G. Murdock

The possible contribution of an improved mineral economy to the further advancement of the lesser developed regions of the world is a vital consideration today. Many of the newly independent countries recognize the problems and the challenge involved in orderly development of mineral resources. Some countries are inventorying resources, planning development, and encouraging local and foreign participation. The Malagasy Republic, composed of the island of Madagascar and the immediately adjacent islands, formerly the French Overseas Territory of Madagascar, is one of the members of the French Community which achieved independence in 1960. It is making real progress towards improving its mineral economy, an effort particularly remarkable considering the generally unfavorable geographic location of the area with respect to world markets and what is, after all, a comparatively sparse-economic mineralization in the light of discoveries to date. Most of the development of the Malagasy economy before independence was fostered by French private enterprise, although the State participated in some ventures. Since independence, the Government has encouraged private investment from a variety of sources through favorable legislation and has indicated that legitimate investment projects that will further advance social and economic programs will be welcome.

Jan 1, 1963

[This Report represents the culmination of work perfomed under Contract No. .,JG1551A8 for the U.S. Bureau of Mine.The &apos;.:o-< embeded a site evaluation, engineering E:-y- ,, esign, and preparation of specifications for construction of a Transport Research 7 :4 (HTRF)The HTRF is designed as a research facility J evaluate the hydraulic transport of large lump coal at a prototype ;e scale. The HTRF is to be constructed and operated by the Pittsburgh and Safety Research Center of ;. re U.-AN a*, their Bruceton, Pennsylvania test center. In terms of technical capability, the HTRF will have transport pipeline:: of -, twelve-, and eighteen-inch diameter _&apos; with supporting coal handling n , water forage a.^ &apos;d conveyance, mixing, pumping, and dewatering equipment, plus instrumentation and controls. Maximum design velocity 13 20 ft/sec.; solids concentration, by, volume, will; 1 be a maximum-- of sixty, percent. Each test loop is designed to accommodate solids of up to one-third the diameter e - of the pine. The Final Report Pr.-&apos;I-rents information of t HTHF,. including the site evaluation, design criteria, a description of the a description of the procedure to be used for operation of the facility, an estimate of the cost to construct the f^Cilit:r, 1 p el_~lli.&apos;iU construe`, icn Schedule, and a construction suicJ_iicaT.l_ccn&apos;. T e c011SLr?Jc&apos;.ion soecl_ i.on _ccnta_i:s technic.&apos;..i re7,uir: (-n`,s for !&apos;urr1S~ &apos;~latcr..al. and ec-uipr,ent for :":C1 C_`:_C ti on of ti,_ H ice&apos; u:&apos;.:i ._II u s(-.6 for ~.Iir: .3!7 soliciting bids. `.l_o included n cc&apos;;,art_- c?r~.air sV:et..: :s ^nd rr^.?]

Jan 1, 1976

By R. S. Dean

The work of the metallurgical fundamentals section during the past year, representing active experimental investigation or thermodynamic study, may be summarized as the following problem subjects: 1. Low-temperature specific-heat investigations. 2. Development of a method of concentrating gases. 3. Thermodynamic properties of metallic carbides and nitrides, 4. Production of pure chromium from chromium chlorides. 5. Thermodynamic properties of the hydrates of calcium, sulphate. While this list is not identical, with officially designated problems, due to overlapping of subjects and to new developments within specified problems, presentation upon the basis of this subdivision will best serve to review the work of the section.

Jan 1, 1937

By AIME

Burton J. Westman-Besides decreasing the diamond size, there appear to be two other approaches open to overcome excessive diamond loss and, more particularly, the rapid diamond polish that took place in this quartz-feldspar rock. First, however, a short discussion of the diamond characteristics should be made in order to discuss the situation more clearly. The West African diamonds which we can assume were used. for this drilling have two disadvantages when drilling hard, exceptionally fine-grained rocks. These are rapid polishing and, if .the bit isn&apos;t "drilled in" carefully, a tendency to damage, resulting in excessive diamond loss. The normal wear resistance of any diamond is inversely proportional to the compressive strength of the diamond, therefore only the highest grade, of diamonds free from insipient fractures should be employed. Using upwards of 90 diamonds per carat instead of the20 to 30 per carat not only decreases the total projected area of the cutting points but increases the stress per point which, in turn, causes greater depth of penetration into the rock. Considering this depth of penetration, therefore, suggests an approach other than increasing the, number of diamonds per carat and that is to decrease the actual number of diamond points (also the carat weight per bit) so that the penetrating force on an individual diamond is increased. This penetration increases the chipping or rock shearing action.

Jan 1, 1950

By Malcolm Scoble, Nick Vagenas, Greg Baiden

Recent advances in underground communications technology have demonstrated the feasibility of teleoperation and automation in underground metal mines. One major challenge lies in the automation of underground mobile machines from surface, with the potential to reduce significantly the need for human involvement in underground operations. This paper reviews the evolution of underground metal mining automation, principally related to the development of teleoperation and automation of mobile mining machines. Examples of prototype systems are given and the associated benefits that have been observed are reviewed.

Jan 1, 1997

By G. Lyle

Since its inception CEMI (Centre for Excellence in Mining Innovation) has focused on facilitating innovative solutions to the mining industry in six strategic research areas; GeoRisk, ConstructMine, ValueMine, FindMine, SustainMine and MineTech (visit www.miningexcellence.ca for details). This paper focuses on CEMI?s largest project to date, Ventilation on Demand (VOD). Energy consumption in mines can account for upwards of 40% of a mines operating cost, with a significant portion of this been consumed by the ventilation requirements. VOD provides a significant opportunity to reduce overall mine ventilation requirements and subsequently energy costs, while potentially increasing mine productivity. CEMI is currently in year 2 of an assessment of VOD, focusing on the financial, physical and equipment viability of utilizing such systems in both new and existing mines. This two year program, to be completed by March 31, 2011, is designed to systematically assess such a system to determine if and when it could effectively be applied in underground mines. The paper will describe the process by which the project was initiated, the demonstration projects established to capture data, the means to interpret the data and the modelling developed to calibrate and predict ventilation system requirements.

Oct 1, 2010

By A. C. Neiva

An energy-dispersive x-ray fluorescence spectrometer was assembled with the aim of analysing alloys and corrosion products of artistic, ethnological and archaeological pieces. The spectrometer is semiportable and consists basically of an 60kV/1.5mA X-ray tube with W anode and a Si-drift X-ray detector with Peltier cooling, with no need of liquid nitrogen. It was used for the analysis of the alloys and occasional corrosion products of several metallic pre-Hispanic pieces of the Museum of Ethnology and Archaeology of the University of São Paulo. Special care was taken to account for the contribution of spurious radiation from both the Pb primary collimator and the Zr detector collimator. The main components of most alloys were Au, Ag and Cu, but Pb, Ca, Fe and other elements were also identified. The characterization of the alloys and corrosion products is important for the subsequent conservation of the collection.

Jan 1, 2006

By R. Guardia, J. Hoskins, E. Claros, Y. Kamiya, R. Ramirez, J. Dalenz, P. Fernandez, E. Ilgren

Crocidolite is a well known causative agent for mesothelioma. Studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width. Epidemiological studies have shown that ‘thin’ fibers from mining areas of Western Australia and the Cape Province, in South Africa are associated with a high mesothelioma risk while exposure to ‘thick’ asbestiform amphibole fiber of the same fiber type are associated with little or no mesothelioma risk. This study is concerned with ‘thick’ Bolivian crocidolite but similar findings also probably explain the paucity of mesotheliomas in the Finnish anthophyllite, South African amosite and African Transvaal crocidolite mines. The findings from the present study suggest the incidence of mesothelioma in the three major cities of Bolivia is not significantly elevated above background even though Bolivian crocidolite has been used for the past 60 years commercially and residentially in all three cities. Although some cases of mesothelioma may have been missed due to a failure to reach hospital or a shortened natural lifespan, mesothelioma generally occurs after the age of 50, we cannot tell precisely the extent to which these were confounding. We suggest the most likely explanation for the lack of mesotheliomas despite the large populations at risk from the long and extensive residential and commercial use of crocidolite containing products, is related to an increased fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By M. A. Schellhardt

The Bureau of Mines has made periodic back-pressure tests on numerous gas wells in the Texas Panhandle field during the past several years to study the delivery capacities of the wells under different pressure and operating conditions and to determine the relationships between pressures and rates of delivery from gas wells.4/ However, information regarding the intake capacities of gas-well systems is meager, end in projects involving the flow of gas into porous-rock reservoirs it has been necessary to determine intake capacities of gas wells by trial. Accordingly the fundamental intake characteristics of natural-gas yells have been studied to develop a method for determining intake capacities under different wellhead pressures from data descriptive of the "output" or producing characteristic of the wells.

Jan 1, 1936

By Elisa Comis, Jeffrey Peterson, Yama Ebrahimi

Construction of the Northeast Boundary Tunnel (NEBT), the last leg of the Anacostia River Tunnel System on DC Water’s Clean Rivers Project, started in September 2018 and was completed in April 2021. The 26-foot-bore earth pressure balance (EPB) tunnel boring machine (TBM) mined 26,737 feet at elevations between 80 to 160 feet belowground. Approximately 55% of the tunnel was cut through lower predominantly coarse-grained facies identified as the Cretaceous Patuxent Formation (undifferentiated) (PTX), and the remainder was cut through upper predominantly overconsolidated fine-grained plastic material facies identified as the Cretaceous Patapsco/Arundel Formation (P/A). Mixed face conditions were encountered in the transition from the P/A to the PTX and vice versa. This paper reviews the performance of the TBM that mined the NEBT through several unique challenges, including 8,000 feet of tunneling under the heavily developed Rhode Island Avenue corridor, major sensitive structures, cast iron water distribution mains, and other sensitive utilities.

Dec 1, 2022

By A. M. Kiwior

In 1969, the Congress of the United States declared that "the first priority and concern of all in the mining industry must be the health and safety of its most precious resource - the miner," Therefore, Public Law 91-173, Federal Coal Mine Health and Safety Act of 1969, was enacted. Since haulage accidents account for a high percentage of coal mining accidents, Section 314e, ?Hoisting and Mantrips,? was included in the law. This section states: "Each locomotive and haulage car used in an underground coal mine shall be equipped with automatic brakes, when space permits. Where space does not permit automatic brakes, locomotive and haulage cars shall be subject to speed reduction gear, or similar devices approved by the Secretary which are designed to stop the locomotive and haulage cars with the proper margin of safety."

Jan 1, 1975

By Slobodan Radosavljevic

The polymetallic W-Pb-Bi-Ag ore from the ?Nova jama? ore zone of the Rudnik ore field have been investigated. Contact-pneumatolytic (skarn), pneumatolytic-hydrothermal, and hydrothermal mineralization phases are defined in this ore zone. The most significant mineralization phase that gave compact ore bodies is pneumatolytic-hydrothermal phase. A relatively pure Mo-free scheelite is the only tungsten-bearing mineral. Lead minerals are mostly presented by Pb-Bi sulphosalts and much less with galena. The image analysis coupled with Energy Dispersive Spectrometry (EDS) analysis on a Scanning Electron Microscope (SEM) was applied to the characterization of a W-Pb-Bi-Ag ore as an efficient tool for mineral quantification. Results of EDS (Energy Dispersive Spectrometry) analyses gave the empirical formulae: Pb1.91Ag0.05Cu0.08Bi1.93S5 for cosalite, Pb0.98Ag0.03Cu0.05Bi1.99S4 for galenobismutite and galena Pb0.99Ag0.03S.

Jan 1, 2006

By Nan C. Jensen

Modern high-temperature metallurgical processes have created a demand for raw material for furnace parts and lining that not only will with-stand high temperatures is but will not react with the substance being melted in the furnace. Spark-plug insulators, laboratory ware, tanks for the glassmaking making industry, and saggers and kiln furniture for the chinaware and pottery trades also must be made of materials hat have high melting points. Among the minerals that can be employed for such refractory uses ore those commonly known as the "sillimanite group&apos; -kyanite, andaluste, sillimanite, and dumortierite - and the allied minerals topaz and pinite. Consideration of the occurrence, properties, qualities, uses, and sources of supply of these commodities and the markets for them constitute the subject of this paper. General Features of Kyanite and Related Minerals Kyanite, andalusite, and sillimanite ire composed of three elements - aluminum, silicon, and oxygen ? and are called aluminum silicates. The have

Jan 1, 1943