Search Documents

By Woodcock J. T

When an aqueous suspension of pyrite and a manganese ore reacts with oxygen, manganese is dissolved by the ferrous sulphate and sulphuric acid produced in situ by oxidation of pyrite. In the absence of added acid, the optimum conditions are: a molecularratio of Mn02/FeS2 of about 1·0, a temperature of about 1400 C., and an oxygen pressure between 25 and 90 lb./sq. in. Under these conditions, complete extraction of manganese is obtained in six hours leaching. An addition of sulphuric acid enables an Mn02/FeS2 ratio of 2·0 to be used successfully.Manganous sulphate decreases in solubility with increase in temperature above 1000 C., but even when the solubility limit is reached during leaching, reaction to form MnS04 still proceeds, and on cooling the MnS04 redissolves.INTRODUCTIONMany manganese deposits contain secondary manganese oxide minerals which are difficult to concentrate. Considerable attention has therefore been given to their hydrometallurgical treatment. In most manganese oxide minerals, the manganese is quadrivalent and must be reduced to the divalent state for dissolution. Reduction and dissolution can be accomplished in a number of ways, one method being to use aqueous ferrous sulphate solutions.A possible source of ferrous sulphate is pyrite as it is known that ferrous ion is an intermediate product in the aqueous oxidation of pyrite. It was therefore thought possible, that by heating an aqueous suspension of manganese oxide and pyrite with oxygen, the ferrous sulphate and sulphuric acid formed from pyrite would provide the necessary leaching reagents for manganese in situ. There are certain advantages in producing ferrous ion in situ...

Jan 1, 1958

By F. Samimi Namin

During the process of developing surface or underground mines, some sites are considered for dumping of surface soils, while others are applied to reclaiming surface and waste disposal. For each kind of overburden, whether it be waste rock, low-grade material, or process tails, a separate storage site is considered so that it becomes possible to transport or recover the overburden separately. Decision-making must be completed by means of a selection process which takes into account the best methods of alternative sets in order to achieve these goals. This decision- making involves many parameters that are inter-related in that changes in some parameters affect the others. There are many methods of decision-making, however, Fuzzy Multi-attribute Decision-making (FMADM) and its functions are studied in this paper. The advantages of this method lies in its theoretical background, formulation, revising capability, unlimited alternatives, and consideration of the counteraction of the different parameters upon one another.

Jan 1, 2007

By R. S. Hearon

The image of the open-pit miner in the eyes or the Environmentalist has never been very outstanding. The phosphate industry, whose history in Florida reaches back to the late 1800's, can-not be credited until recently with a large number or accomplishments in terms of protection or the environment to change this image. This lack of action was not deliberate or in opposition with the desires of the public. In the formative years, there was little or no public and the companies found it necessary to build towns to house their employees and their families, towns which remained in existence until the late 50's and early 60's or formed the core of present large communities. Neither these pioneers nor most subsequent resource developers considered themselves un-thinking spoilers, nor were they so regarded by their contemporaries. Instead, they acted in a manner consistent with their environmental circumstances and intellectual heritage. Early Americans did make mistakes in using the land but the mistakes became apparent only in the opinion of later generations. Over the past five to ten years, there has been a new self-awareness in the industry with regard to environmental responsibilities brought about, in part by a continuing onslaught of new regulations with jurisdiction over our activities. Part of the new regulations are aimed at industries as a whole while many, particularly state regulations, pertain specifically to the phosphate mining industry. Why all the new regulations? The reasons are encased in a complex web of activity but stem primarily from a new public awareness of its environment. More and more of our youth have become interested in the environmental science areas such as biology and ecology. The tremendous growth rate in both the population and industry has made personal issues out of subjects such as atmospheric inversions and water shortages which previously were abstract concepts. The State has grown from a population of 1,500,000 in 1930 to approximately 9,000,000 people today. This personal impact and general lack of knowledge on the part of the public concerning economics has resulted in big business no longer being held in awe, often in contempt and generally in suspicion where environmental concerns are encountered.

Jan 1, 1978

By Minna Karstunen, Patrick Becker

"Abstract The deformation behaviour of a foundation on deep mixed columns in a natural soft soil is a three-dimensional problem, which has to be considered adequately in numerical modelling. However, simplifications are often made due to the computational costs of fully coupled 3D analyses by either modifying geometry of the problem or material parameters in 2D for plain strain analyses or by modelling the problem as 2D axisymmetric case. The volume averaging technique (VAT) is an enhanced 2D FE technique that enables mapping the 3D problem in two-dimensions, yet modelling the two constituents (column and soft soil) with appropriate different constitutive models within a homogenized material. The performance of the volume averaging technique is demonstrated by considering unit cell simulations of floating and end bearing columns in soft soil. The results with VAT are compared and validated against conventional 2D axisymmetric and fully coupled 3D finite element analyses.IntroductionThe properties of very soft clays, silts and organic soils can be improved by stabilizing agents, such as lime and/or cement that are mixed into the soil in situ by using auger-type mixing tools in situ. Deep mixed columns are extensively used to reduce deformations and to improve the overall stability of embankments and foundations on soft soils. Whilst the most typical applications are embankments, increasingly the method is used under foundations. The first category of applications is very common in Scandinavian countries, whilst the latter application has been pioneered in Poland, as an environmentally friendly (low CO2) and cost effective alternative for piling. Due to economic and environmental reasons there is an increasing interest in the technique elsewhere in Europe. With deep mixing, the strength and deformation properties of the soft soil can be improved, and the risk of unwanted deformations is substantially reduced.Numerical methods, such as finite element (FE) analysis, can be used as an alternative to conventional design methods. They are particularly suitable when considering serviceability limit state, i.e. deformation analyses under working loads. FE analyses allow using advanced constitutive models that take account of the complex stress-strain behaviour of natural soil and stabilized columns, respectively. The problems that involve a grid of circular columns under an embankment or a strip footing are fully three-dimensional problems. As 3D analyses are very laborious and expensive, an enhanced 2D technique using the so-called volume averaging technique (VAT) is utilised. The basic idea is to describe the column-improved ground as a homogenized composite material, and using clever mathematics to map the true 3D problem into 2D. Once the constitutive relations of both composites are defined, the response of the column-improved ground can be simulated in 2D subject to arbitrary loading and boundary conditions."

Jan 1, 2014

By Nageswararao K

A series of tests was carried out on one of the rock-pebble milling circuits treating complex nickel ores at Kambalda Nickel Operations of Western Mining Corporation. A mathematical model to describe the behaviour of a 508 mm hydrocyclone was developed from the data.A "flat" reduced efficiency curve was observed for the system. This was attributed to a marked difference in the specific gravity of different size fractions of the feed. A modified approach in describing the shape or the reduced efficiency curve resulted in accurate prediction of the hydrocyclone performance.

Jan 1, 1981

The acid plant consists of the following units: 1. Glover tower. 6. Mills-Packard type chambers. 3. Reaction towers. 6. Gay-Lussac towers.The sulphur dioxide bearing gases, used in the manufacture of the acid, are obtained from the roasting of zinc concentrate. Six Herreshoff type furnaces are available, each with an effective hearth area of 520 sq. ft.The concentrate contains approximately 30% sulphur, of which about 72 is ultimately recovered as acid. The oxides of nitrogen are added to the gases in the requisite proportions partly from nitrous vitriol and from nitric acid in the Glover tower, and partly from nitrous vitriol in some of the chambers and connecting flues.The acid leaving the Glover tower is cooled by the ordinary water-cooling coils, while the cooling of the chamber gases is effected by circulating water over the outer surface of the chambers, and by spraying nitrous vitriol and weak acid into them.Flow of gases throughout the plant is regulated and controlled by means of regulus metal fans, fitted with variable speed gears.

Jan 1, 1934

By Ken Wood

"A reliable source of water of an acceptable quality is vital to the success of any mineral processing plant using wet methods. For Cerro Verde, a new 108,000 t/d copper mill in southern Peru, the main source of raw water is the Chili River. The Chili River is heavily contaminated with raw sewage, industrial wastewater and agricultural runoff, and can also receive high sediment loads during the rainy season. The initial water treatment plant could not supply design flows of water due to the exceptionally poor water quality. Problems with treated water quality caused significant difficulties with water consuming equipment, such as the plant cooling systems. This paper details the Cerro Verde water system and changes from design through to start up from a mineral processing perspective.INTRODUCTIONMining, and mineral processing in particular, is a water intensive activity. Improving water system design and practice are key strategic requirements in moving toward a more sustainable mining industry. This case study forms a basis for ongoing research into water use and reuse at mines and mineral process plants, conducted by AJ Gunson, under the supervision of Dr. Bern Klein and Dr. Marcello Veiga at the University of British Columbia. The case study material was gathered through involvement with the design, startup, and redesign of the Cerro Verde water system.Cerro Verde is a low-grade copper porphyry mine, located near the city of Arequipa in southern Peru, at an elevation approaching 2,800 m. In 1972, one of the world’s first copper Solvent Extraction – Electrowinning (SX/EW) facilities was built on the site, processing oxide ore from two main open pits. In 2004, the operator, Sociedad Minera Cerro Verde S.A.A. (SMCV), approved a 108,000 t/d expansion project to process sulfide ore reserves through a new concentrator plant. The plant was designed under extremely tight schedule and capital constraints, with a mandate to intentionally avoid any overdesign."

Jan 1, 2008

By L. Echeverri

Research studies have shown that the flow within feedwells displays a vortical structure and high velocities at the locations where standard tangential inlets force its way into the feedwell swirling flow, producing high local shear rates and flow non-uniformities. These hydraulic deficiencies can be attributed to the discrete feeding through a few entrances, usually one or no more than a few tangential feedpipes, which practically project jets into the vortex within the feedwell. The main consequences are unequal flocculation with aggregates subjected to different amounts of shear and a non-uniform discharge from the feedwell. This paper presents results on the application of CFD and small-scale models to develop a new design that overcomes these problems by using an involute shaped inlet that converges around the feedwell. The result is a new feedwell with enhanced hydraulics that perfectly couples with the FLSmidth E-Duc® Feed Dilution system by protecting the flocculated aggregates that have been carefully produced upstream, and that favors uniform sedimentation conditions within the thickener thanks to a uniform discharge, while maintaining a practical and trouble-free geometry with excellent turndown.

Jan 1, 2012

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

By V. K. Paruchuri, J. D. Miller, J. Nalaskowski

The phenomenon of surfactant adsorption at mineral surfaces is of significant importance in many particulate processes ranging from mineral flotation and enhanced oil recovery to pharmaceutics, paint technology and the casting of high quality ceramics. Stability of the dispersions is related not only to the amount of adsorbed surfactant but also to the structure of the adsorbed surfactant molecules at the interface. This structure greatly depends on the type of surfactant and the hydrophobicity or hydrophilicity of the surface. On hydrophobic surfaces surfactants adsorb regardless of surface charge by van der Waals/hydrophobic inter-actions with hydrocarbon chains accommodated at the surface. On the other hand, on hydrophilic surfaces the surfactants adsorb through electrostatic interactions with their polar moiety fixed at the surface. In the latter case, the electric charge of the surface and surfactant plays a crucial role in the surfactant adsorption process. The recently developed soft-contact Atomic Force Microscopy technique has revealed images of adsorbed surfactant structures at various interfaces. The adsorbed structures of a cationic surfactant (CTAB) and an anionic surfactant (SDS) are presented in this work for different concentrations at hydrophobic graphite and hydrophilic mica surfaces. Different types of micellar arrangements have been observed at these surfaces for surfactant concentrations around the critical micelle concentration. The structures are more ordered and well defined at the graphite surface than at the mica surface. These results have been correlated with the hydrophobicity of the surfaces as revealed by contact angle measurements.

Jan 1, 2001

This Bureau of Mines report contains the proceedings of a symposium cosponsored by the Bureau of Mines and the University of North Dakota concerning utilization and technology of Western coals and lignites. The symposium, the sixth in a series, comprised 12 papers.

Jan 1, 1972

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

THE successful establishment of iron blast-furnace plants at Newcastle and Lithgow naturally invites attention to the economic utilization of the various products and by-products arising out of the industry.The general similarity in composition between Portland cement and iron blast-furnace slag very early attracted attention both in, the cement and iron-smelting industries. Probably the first use made of blast-furnace slag in the cementindustry was not of an honourable nature-viz, to use an almost worthless and cumbersome by-product as a not readily detectable adulterant in Portland cement, which was at that time very costly to manufacture.The astonishing discovery was made that in many cases the adulterated cement was stronger than the original unadulterated article. It was found that chilled blast-furnace slag introduced in moderate quantity and finely ground with the cement clinkerdid not injure, but usually improved, the quality of the resulting cement. This mode of, manufacture is recognized, especially in Germany, as a legitimate branch of the cement making industry.The use of slag for the manufacture of both slag cement and Portland cement has assumed very large proportions heth in USA and Europe so much so that in the former country plants not well situated and equipped for cheaply making cement from clay and limestone are being forced to close down. Slags from other than iron blast-furnaces, together with some of the latter, are not suitable for cement-making. All slags which disintegrate and fall into powder are wholly unfitted for cementmaking.Those highly charged with mineral oxide compounds...

Jan 1, 1918

The centrifugal elevator invented and patented by the writer is designed for the purpose of conveying the tailings of a gold dredge to such a distance that it shall not impede the dredging opperations. Formerly this was usually accomplished by means of a belt of buckets travelling round a ladder set at an angle of about 30 degrees to the horizontal, but this meant heavy wear and tear on the travelling buckets and the tumblers actuating them. The centrifugal elevator throws the tailings through the air to the required height and distance and it is manifest that during their flight from the elevator to the heap there is absolutely no wear and tear, only the attraction of gravity and the resistance of the air has to be overcome. All then there is left to he considered is how to throw the stuff with the minimun of prower and wear on the elevator.The elevator consists of a cam-shaped steel casting with a disc of mild steel plate on either side: These side plates project a few inches beyond the tips of the beaters, in order to prevent odd stones from straying in an undesired direction; they serve also to prevent extra large stones from reaching the beaters, for they slide off the rims into the water.

Jan 1, 1904

The Greymouth Coal Project is a proposal to mine by the application of proven hydraulic, and room and pillar underground mining methods; and to process the equivalent of an average of 1.7 million tonnes per year over a forty-year period. The proposed mine site is located ten kilometres north of Greymouth, on the west coast of the South Island of New Zealand. Of the three separate mineable seam groups, the thick Main Seam Group, which makes up 77% of the total resource, will be mined by hydraulic mining technology.   It is proposed to market and produce a high volatile bituminous type coal with low ash (6%) and sulphur (0.4%). Because the inherent ash content is low, the requirement for coal treatment will only be the use of a single cell jig circuit to control the effects of rock dilution and partings. The resulting coal product is tentatively planned to be transported by rail to the port at Lyttelton for loading on to Panamax or Post Panamax size vessels.

Jan 1, 1997

By Dennis J. Grigal

The objective of this contract was to monitor operating conditions of, four flooded, fibrous-bed filter panels used during normal underground mining operation and to analyse clogging and structural problems. After observing structural and clogging problems and conducting laboratory and field tests, a final, Flooded, fibrous-bed filter design which minimizes clogging and structural problems was recommended to the Bureau of Mines. This report also describes the dust sampling procedures used to determine the dust concentration at the flooded, fibrous-bed scrubber intake duct.

Jan 1, 1979

By Benedicto Hadad Cintra

In an inflationary environment the need for reduced cost is a daily concern of all industries. The Du Pont do Brasil "Expanded Pattern" method has proven to be an extremely effective means of reducing costs in mining, quarrying and construction operations. Over the past years much emphasis was placed on rectangular drilling patterns where the burdens are less than the spacing. The Expanded Pattern method combining rectangular and staggered patterns, was implemented in 1971 in Brazil after extensive trials in close collaboration with numerous explosives users and Du Pont do Brasil Technical Services Engineers. The best multiple row spacing-to-burden ratio (S/B) was demonstrated to be in the 2 to 5 range and the effective spacing to burden ratio (Se/Be) was found to vary from 5 to 11. These ratios are for the interior of the blast pattern and do not hold true along the front row of holes. Geological rock properties, hole diameter and inclination, explosives energy and loading density, explosives characteristics, blast pattern geometry, bench height and delay patterns along with type and size of digging, hauling and crushing equipment must all be evaluated for each and every operation. The integration of these interrelated parameters, together with sound blasting practices are the basis for the Expanded Pattern method. Color slides and documented case histories will be presented.

Jan 1, 1985

This study explores two evolving 3D surveying technologies, photogrammetry and laser scanning, and applies them to deformation monitoring of rock faces and mine highwalls. A quantitative analysis focused on 3D coordinate determination is performed. Furthermore, a qualitative assessment directed at the practicality and viability of each system operating near a rock face or in a mining operation is undertaken to reveal one systemÆs deficiencies over the other. Two photogrammetric and four laser scanning surveys aimed at optimising accuracy and precision within a short period of data acquisition are conducted on the rock face at Organ Pipes National Park, Keilor, Victoria. The accuracy and repeatability of each survey is determined using a combination of iWitness photogrammetric, and Cyclone laser scanning software. The 3D coordinates of targets placed on the rock face are determined by triangulation and resection principles within a bundle adjustment. The coordinates determined by each system are then compared in a 3D transformation. Controlled deformation conditions are established to determine the precision to which each system can detect movement in the rock face. An object of known dimensions is placed on the rock face to simulate deformation. The relative orientation of images taken for the pre- and post-deformation photogrammetric surveys provide an overall 3D point accuracy of 1.255 mm and 1.804 mm respectively. A 3D transformation shows discrepancies of less than ¦22 mm (RMS) between the geometry of the photogrammetric and laser scanning models. Both systems are able to detect the simulated deformation to a precision of 50 mm. This work also identifies how to obtain millimetre accuracy for 3D coordinate determination of rock faces, thereby providing a quality data set for surveyors, geotechnical engineers and mine geologists. Photogrammetry is shown to be a mobile, time and cost-effective technique that is more amenable to mining operations than terrestrial laser scanning. However, both systems demonstrate that they are capable of detecting movements that may lead to failures in the rock face, and possibly endangering human life. The implications are significant for surveyors, geotechnical engineers and mine geologists working in mining operations where enhanced safety conditions, increased productivity and lower operational costs are important considerations.

Jan 1, 2009